Search Documents

By A. J. Teplitz, T. Bardeen

In the course of an investigation of lost circulation, a new tool has been developed which gives a qualitative measure of the relative velocity between the fluid column in the borehole and the tool. The position of a diaphragm in the side wall of the instrument depends on the flow through the device. This position is established by using the conductive borehole fluid in a potentiometric circuit. The instrument has high sensitivity and can detect changes in velocity as low as. 5 ft/min. Lost circulation mud additives do not interfere with the satisfactory performance of the tool. In a number of circulation losses of the pressure induced type, the instrument has shown that the losses were confined to extremely narrow zones (less than I ft), indicating that such ruptures occur in a more or less horizontal rather than vertical plane as has often been assumed. This pinpointing of the zone of loss is important in remedial procedures since it allows the treatment to be applied directly to the point of loss rather than to the entire open hole. The device can also be employed for indicating points of entry of water in producing wells. INTRODUCTION The need for an improved means of locating the positions of lost returns zones became evident during an investigation of lost circulation difficulties in the Gulf Coast area.1 With instrumentation available at the time, it had been learned that, contrary to common belief, the position of the thief zone responsible for a given loss seldom coincided with the point of bit penetration at the time the loss was encountered. In the majority of cases, the losses were found to be occurring at some distance removed from the bottom of the hole —sometimes as much as a few thousand feet. This information, along with other observations made during the investigation, led to improved techniques' for dealing with lost circulation problems. Highlighted, however, among the results of this work and of similar studies subsequently conducted in drilling operations in other parts of the country, was the indication that a considerable portion of the difficulty and expense involved in treating prolonged circulation losses is due to the unsystematic application of remedial measures to one or more apertures of unknown position. Basis of Tests It is worth considering that if the troublesome formation could somehow be transported to the surface where it could be directly observed, there would likely be little difficulty in readily effecting a seal. Although this is a decided oversimplification of the situation, it does appear that the chief obstacles to similar ease of handling of a lost circulation zone in a well are lack of visibility and of ready accessibility. The latter handicap is overcome to a considerable extent by placement techniques already in use, and other procedures now in the process of development are expected to offer further improvement. But in the matter of visual observation, the technique to be presently described appears to afford a quite satisfactory substitute.

Jan 1, 1957

By Raymond B. Ladoo, C. A. Stokes

This paper summarizes the economic problems of the industrial mineral industries which are essentially different from those of the metals and the fuels. Failure to understand and evaluate such factors as markets, place value, and substitutions of one mineral for another may be disastrous. The engineer should be as responsible for profitable operation as he is for technical efficiency. The Raw Materials Survey of Portland, Oregon, is described.

Jan 2, 1950

By H. T. Clark

Within the last twenty years at least three sets of lattice constants for the room temperature (alpha, hexagonal close packed) phase of titanium have been reported in the literature. These values, summarized in Table 1, differ one from another by amounts far greater than can be explained on the basis of inaccuracies in parameter measurements. This paper presents new values determined for high purity titanium. It also details the effect of two elements, oxygen and nitrogen, on these parameters and shows that two of the previously reported values are probably in error because of the presence of one or both of these elements in the material used for examination. Preparation of Samples The titanium+ used for this study was prepared by the thermal decomposition of titanium tetraiodide7 on a hot titanium filament. This titanium rod was prepared for X ray examination by melting about 10 g in purified argon in an electric arc furnace on a cold hearth. This cast button was cold rolled to 0.040 in. thick sheet, cleaned, annealed in vacuum at 1000°C and cold rolled to 0.020 in. thickness. About 0.003 in. of surface material was then removed by hand grinding on papers to remove any contamination caused by the rolls and the sample was bent to the radius of the focusing camera. The sample was then vacuum annealed at 600°C, a temperature just high enough to cause recrystallization, producing a fine grained structure. Such a structure is essential in sheet specimens prepared for focusing cameras in order to have a sufficient quantity of grains to develop continuous diffraction lines. The use of sheet specimens rather than powder samples appears to be essential for the X ray examination of titanium. This is because of titanium's exceptionally high gettering power and its rapid absorption of adsorbed gases, water -vapor, and the like at annealing temperatures. While the effect of this contamination may be neglected for sheet specimens, its effect on 200-300 mesh powder is appreciable. Titanium alloys of oxygen and nitrogen were prepared by a technique simi- lar to that described above except that the required amount of the highest purity titanium oxide or nitride available was added prior to melting in the arc furnace. These materials were added by placing them in holes drilled in the titanium. A small weight loss invariably occurs during the melting of these oxygen and nitrogen alloys. This is believed to be due entirely to the loss of some of the powdered compound in the blast of the electric arc, an assumption which is justified on the basis that there is no weight loss during the melting of titanium metal and that wet analyses for nitrogen on representative samples have checked with the calculated analyses when it was assumed that the entire loss during melting was due to the loss of titanium nitride powder. These alloy buttons were reduced to sheet in the same manner as used for the unalloyed titanium. Experimental Procedure A North American Phillips 12 cm diam symmetrical precision focusing vacuum camera and copper radiation

Jan 1, 1950

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By A. F. Frederickson

Rapid advances in any branch of science often follow the development of new instruments or techniques which permit the scientist a closer look at the material in which he is interested. With the development of the polariz¬ing microscope, modern petrology was born. The resolving power of the microscope, however, was not great enough to enable the geologist to dis¬tinguish or identify the material now known to be minerals which constitute the bulk of the rocks known as "clays" and laterites. The discovery of X-rays and the development of powder X-ray diffrac¬tion techniques provided the extra resolving power necessary to get "a closer look" at the minerals in the clays and laterites. These techniques are largely responsible for the great strides made in the past two decades in the identification of the clay, sesquioxide and hydroxide minerals. To obtain an X-ray diffraction. pattern of a mineral or rock is relatively a simple procedure, but to interpret this pattern in terms of crystal structure or min¬eral identity is quite another matter. It has taken the combined talents of physicists, physical and colloid chemists, mineralogists, and geologists to unravel the identity of some of the minerals in these complex rocks and, as this symposium will indicate, many more problems remain to be solved. To assist in the identification of these minerals, we have the ever-useful microscope, which, is supplemented by the development, only in the last ten years, of differential thermal techniques and the powerful and costly "eye" that enables us to see the shapes and sizes of extremely small particles -the electron microscope. To this array of equipment must be added such gadgets as supercentrifuges, spectrographs, and the apparatus necessary for chemical analytical work. Obviously, not only is it difficult for any one man to master all of the techniques to the point where he can do competent re¬search, but also few institutions are able to provide the high capital outlay for purchase and maintenance of suitable equipment. Here we clearly see that if this equipment is to help us solve our many problems, a close co¬operation of specialists from various institutions and industry is essential. This, however, is less than half the problem. If the geologist is going to learn to intelligently find, and the industrialist to intelligently and eco¬nomically exploit the materials that constitute a large part of the mineral wealth upon which our way of life is based, we must get a better insight into

Jan 1, 1952

GEORGE F. BECKER Dr. George Ferdinand Becker, notice of- whose death appeared in the May Bulletin, was born in New York City Jan. 5, 1847, the son of Alexander Christian Becker, member of a Danish family, and Sarah Cary Tuckernian Becker of Boston. Dr. Becker was the last member of the group of distinguished geologists who, in 1879, were associated with Clarence King at the time of the organization of the United States Geological Survey. He was a leader in mining geology and geophysics, and for many years had been the chief of the Division of Chemical and Physical Research in the Geological Survey, and the investigations under his direction led to the establishment of the Geophysical Laboratory of the Carnegie Institution of Washington. Dr. Becker was a graduate of Harvard University and received the degree of Doctor of Philosophy at Heidelberg, and in 1871 passed the final examinations at the Royal School of Mines in Berlin. He was for four years an instructor of mining and metallurgy in the University of California, from which he went to the United States Geological Survey. In 1896 he examined the gold and diamond mines f South Africa and at the time of the Spanish-American War was detailed to serve as geologist on the staff of General Bell with the army in the Philippine Islands. He died at his hone in Washington, D. C., on Apr. 20'.1

Jan 6, 1919

By J. Jones-Parra

In previous Technical Notes, W. R. Rose' and W. Purcell have discussed the capillary pressure data presented by Welge.' Welge obtained capillary pressure curves of the imbibition type in which it was necessary to apply to the apparent wetting phase a greater pressure than that of the non-wetting phase to complete the cycle and reduce the non-wetting phase saturation to low values. Rose suggests in his Note that conditions of equilibrium could not have prevailed, since the. non-wetting phase pressure must always be the greater. Pur-cell in his Note, proceeds to postulate a pore system consisting. of a series of "holes in a doughnut," in which he contends that under equilibrium conditions it is necessary to resort to negative capillary pressures before significant wetting phase displacement can take place. There is a remarkable similarity between the shape of the capillary pressure curve calculated by Purcell and those measured by Welge. It is the purpose of this Note to show that, because Purcell neglected to account for the behavior of the residual wetting phase saturation, his system was not in equilibrium during imbibition; and, furthermore, that if his system had been in equilibrium, negative capillary pressures would not have been possible. In Purcell's pore system, the residual wetting phase will form pendular rings at the interstitial spaces existing somewhere within the system, for example, such as those spaces between "doughnuts" as shown in Fig. 1. The true capillary pressure is that across the pendular ring interface, and for the system to be in equilibrium the pressure drop across all interfaces must be the same, including that across the interface in the tight pores A of diaphragm B (Fig. 1). As the pressure across the cell is reduced, the advancing interface will move into the pore from the diaphragm, but at each pressure, the curvature of the pendular rings must be the same as that of the advancing interface if equilibrium is to prevail. Since equilibrium conditions are the basis for the entire argument, it follows that pendular rings must grow as wetting phase enters the pore, that is, as the pressure across the cell is lowered. In Purcell's calculated curve, the residual wetting phase saturation remains constant as the capillary pressure decreases. Thus, his curve does not represent an equilibrium process.

Jan 1, 1953

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.' I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

THE strike of the coal miners began on April 1, as had been expected, the entire force of unionized miners-both anthracite and bituminous-going out and making this the most widespread strike of record. Up to the present writing there has been no serious inconvenience to industry in general, the accu-mulated stocks of coal being large and the non-union mines having continued to make a substantial production. However, the union labor leaders, having concentrated their efforts toward inducing the non-union miners to go out also, met with some measure of success in certain fields and created a shortage of coking coal, which caused iron makers to bank a few furnaces. The strike of textile workers in New England spread further. Here and there, throughout the country there were sporadic troubles with the builders. Rail-way labor was the subject of continued palavers, which did not get anywhere. On the whole the events of April were in line with the forecast that this would be a year of labor troubles. In domestic politics, the soldier bonus bill, having been passed by the House, went to committee consider-ation in the Senate. Public opposition to it manifestly waxed. On the floor of the Senate the tariff bill was under consideration and is drawing nigh to passage, without there being much consideration of its probable economic consequences. It is going to be a very high tariff and there is much in it that is equivalent to subsidizing small and normally unprofitable industries at the expense of the people as a whole. Abroad affairs were more quiet, superficially at least; than they were in March. In Egypt, India and South Africa things calmed, down, so far as we know, but in Ireland there was continued turmoil. The Irish, having won their freedom to the same degree as the Canadians, have entered upon violent quarrels among themselves, more over phrases than anything .else, so far as we can see. Lloyd George obtained a spectacular vote of confidence from Parliament and thus postponed, the exigency of a general election.

Jan 5, 1922

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

By S. D. Michaelson, Eric Sinkinson

Many of the magnesite ores of the western part of the United States contain such large amounts of silica and hydrous silicate minerals that the value of the ores is either low or nominal. Expensive and carefully controlled mining methods are necessary to prevent excessive dilution of the higher grade ores by introduction in mining of small pieces of the hanging walls or footwalls of the deposit. This difficulty is further complicated by the various states of decomposition of the country rock of the deposits in which many of the ores occur. The problem the authors attempted to solve arose from a request to float an impure magnesite containing varying proportions of siliceous gangue with calcium carbonate. The ore is normally enclosed in serpentine masses, somewhat decomposed, and in mining it wall rock is incidentally added, so that variable amounts of siliceous material occur in the samples. The silica, alumina, and iron oxide are so closely associated with the magnesium carbonate in the magnesite that ordinary mechanical separation at coarse mesh sizes is of no avail. It is well known that calcium carbonate can be floated by suitable reagents, therefore it seemed reasonable to suppose that magnesium carbonate minerals would behave in a similar manner, but experimental trial proved that this supposition was unfounded. Therefore the first step in the problem was to find out what differences of behavior there were between magnesium and calcium carbonates under flotation conditions, or when suspended in water. In water at 18" C. magnesium carbonate is slightly more soluble than calcium carbonate; in fact, MgCO3 is soluble to the extent of 0.0106 grams in 100 c.c. of water at 18" C. and CaCO3 to the extent of 0.0013 grams. However, magnesium carbonate in water gradually changes to the basic carbonates of a composition (3MgCO3.Mg(OH)23H2O) or (4MgCO3.Mg(OH)25H2O), depending upon conditions, and calcium carbonate to calcium hydroxide, Ca(OH)2. The relative solubilities of these hydroxides in water are the reverse of the solubilities of magnesium and calcium carbonates. The range in published figures for solubility

Jan 1, 1938

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year's meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

By Harry J. Morgan

One of the greatest improvements in drilling equipment has been the development of hard facing metals which are welded by electricity or by acetylene to form a facing which protects the steel of the bit from abrasive wear. The main desirable characteristics of hard facing metals are resistance to abrasive wear, resistance to shock and perfect bond with underlying metal. Resistance to abrasion offered by various metals shows many anomalies. Compounds containing carbon, silicon and boron are the most important hard substances. Carbon, as diamond, silicon carbide and especially the carbides of iron, chromium and tungsten are the outstanding hard products in common use. Tungsten carbide is probably the most commonly used. It is made in the electric furnace and it is important to get the right amount of carbon and the correct crystalline structure in order to obtain the greatest hardness and greatest resistance to abrasion. It may be obtained in three main divisions: wrought, cast and casehardened. Insert hard metals are common. The method of application varies, but it is generally welded to the bit, placed in channels or in drilled holes and covered with a hard surfacing metal. Robinson' has given a very complete article on the use of inserts. Gregg and Küttner2 has discussed the metallography of tungsten carbides and given a good bibliography of the subject,. The time and expense of large-scale testing, together with variations in results, led to the development of a laboratory testing machine for determining the abrasive-resisting qualities of different metals. This machine consists of a motor-driven 40-grain, alumina-base corundum wheel, 8 in. dia., rotating at 30 r.p.m. It is run wet and dressed with

Jan 1, 1930

By H. W. Paxton, G. M. Pound

A method is outlined for taking into account variation in chemical potential of both components in evaluating capillary effects at growing interfaces. The results are compared with experiment, and seem to be in reasonably good accord for Widman-statten ferrite growing in austenite. ENERY pointed out that during the steady-state growth of phases with a rather small radius of curvature at their advancing edge capillarity cannot be neglected. By proper application of the Laplace equation a correction must be made to the activity gradients down which diffusion occurs. Subsequent workers have concerned themselves with attempts to evaluate specific cases by the use and modification of the principles laid down by Zener.2-5 To solve the problem in its simplest form it is necessary to assume thermodynamic equilibrium at the interface and to select some criterion which will allocate the available free energy between reversible and irreversible processes. Zener chose to assume that the division should be made such that the new phase grew at the maximum rate. Other workers have used the same2,3 or different assumptions, e.g., maximum rate of free-energy dissipation,4 minimum rate of entropy production.5 Li6 has proposed that the "thermokinetic potential" should be a minimum at steady state. The purpose of this presentation is to note that most prior treatments have considered variations due to capillarity only in the chemical potential of the mobile constituent, and that a more consistent treatment must involve a consideration of the variation of chemical potentials of both solute -and sol- vent in a binary system.* As an example, the way in which this arises for ferrite growing from austenite may be illustrated by reference to Fig. l(a). The line OABC shows a typical variation of carbon activity with composition at one atmosphere pressure (at a transformation temperature below A3). In the tip of a growing ferrite plate with a hemi-cylindricab leading edge of radius ?, the pressure due to capillarity is*

Jan 1, 1963

By S. C. Carapella, E. A. Peretti

DURING a literature survey of the indium-zinc phase diagram, controversial reports on the composition of the eutectic point were encountered. The value reported in the investigation of Wilson and Perettil and in a later investigation by Valen-tiner' was 4.0 wt pct zinc. The most recent work recorded on this system consisted of an exhaustive survey of alloys by Rhines and Grobe8 in which they indicate a value of 2.8 wt pct zinc for the eutectic composition. To clarify this aspect of the diagram, a series of alloys were prepared by melting the respective constituents in a glass test tube under a covering of mineral oil and slowly cooling the melt in a furnace. The zinc used was Baker's C.P. and had the following analysis: insoluble in H2SO4—0.0l pct; pb—0.001 pct; Fe-—0.001 pct. The indium, which was supplied by the Indium Corporation of America, had a purity of 99.9'7 pet with the following impurities: Cu—0.002 pct; Pb—0.006 pct; Sn—0.01 pct; Zn—0.01 pct. The alloys were prepared for metal-lographic examination using a technique already reported' and a new value of 2.0 ± 0.1 wt pct zinc was observed. An alloy containing 2.00 wt pct zinc was also made by melting the constituents under a vacuum. In both of these methods of alloy preparation the losses can be kept extremely small. Again, the characteristic eutectic structure was obtained, assuring confidence in this value. The accompanying micrographs are presented in support of this point. Fig. la represents an alloy containing 4.00 wt pet zinc, and reveals excess zinc particles, which precludes the value of both Wilson and Peretti, and Valentiner. Fig. lb, gives the structure of an alloy containing 2.2 wt pct zinc, also showing the presence of excess zinc. Fig. lc is a micrograph of a typical structure of the eutectic observed in several sections of the 2.0 wt pct alloy. In the 1.8 pet zinc alloy, fig. id, the definite presence of the primary indium can be noted. From these re-

Jan 1, 1951

By Howard L. Hartman

6.1-1. Introduction. Of necessity, the first of the unit operations conducted during the exploitation phase in surface mining is production drilling. It precedes blasting, with which it is associated as the two unit operations employed to break or fragment consolidated material (usually rock) in place. The purpose of production drilling is to provide the cavity for placement of the explosives. So far, no alternative to blasting has been devised for fragmenting very resistant rock in situ, although some forms of excavation (ripping, bucket wheel) are suitable without prior blasting for softer rock, such as weathered shale or mudstone, decomposed sediments, etc. For the vast majority of surface mines, however, drilling and blasting are pre- requisite to excavation and essential to the production cycle. Drilling is also used in surface mining for purposes other than providing blastholes. It finds application during exploration for obtaining samples and during development for drainage, slope stability, foundation testing, etc. Only in the exploitation phase of surface mining, however, are unique or specialized drilling methods and equipment employed; and the discussion in this Section is directed primarily to that application of drilling. Drilling is the most common means of rock penetration, the operation of placing a directed hole in rock. Closely akin to drilling for exploitation purposes is the cutting or freeing of dimension stone in quarrying. This operation, usually termed channeling or sawing, also takes the form of directional penetration of rock; but instead of producing a cylindrical hole, it yields a kerf or cut. The material thus freed from the solid is both a shaped and sized product, an objective of vital importance in the dimension stone industry. In sawing, holes are sometimes drilled to insert tools, but this drilling is a minor part of the sawing operation and employs conventional methods. Cutting, as a unit operation for freeing stone in quarrying, may be considered equivalent in purpose to drilling and blasting in other forms of surface mining.

Jan 1, 1968

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By T. Prof. Ph. D. Egleston

THE importance of having perfectly pure metals has led me to present to the Institute a record of some of the trials that have been made to obtain these metals, and also to show one of the largest specimens of extremely thin metal plate which has ever been made. The malleability of metals varies generally directly with their purity, and hence it is only with very pure metals that thin sheets can be obtained. The competition among different manufacturers has been so great at times as to lead to expensive and apparently useless experiments in obtaining in the first instance very thin sheets, and afterwards very large and thin sheets of metal, apparently with no other purpose than that of being able to say that they had produced the thinnest or the largest thin sheet that had ever been made. These experiments were at first confined exclusively to iron, their object being to show the great dexterity of manipulation, as well as the purity of the metal manufactured. They have since been extended to almost all metals by electrical action, and have gone far beyond the limits of what was possible with purely mechanical means. The processes which have been used are rolling or hammering, electrical deposition in a vacuum, and lastly, electrical deposition on plates, easily soluble in acids. The first and last of these methods have been known and practiced for a very long time, having been used to make thin sheets of almost all the metals. The other is of quite recent application. In the iron manufacture, the strife to produce these thin sheets was commenced in the year 1865, by the Sligo Iron Works writing to a firm in Birmingham, England, on a sheet of iron containing 270 square centimeters, and weighing only 4.469 grams. For some time this was considered to be the thinnest sheet iron that could be made. T. W. Booker & Co., of Cardiff, England, however, produced a few months afterward, a sheet of the same size, weighing only 4.015 grams. This was succeeded by one rolled by Neville and Everitt, of Llannelly, weighing only 3.174 grams. This was followed by one from Hallam, of Swansea, which was 283 square centimeters in size, and weighed but 2.979 grams; and this by one rolled by R. Wil-

Jan 1, 1879

By Clarence Zener

IT has long been known that the density of a metal usually decreases with cold-work. Thus O'Neill1 observed as early as 1861 that cold hammering of commercial hot-rolled copper is accompanied by a decrease of density of 0.2 per cent, and that subsequent annealing restores the original density. The origin of this density change, however, has remained obscure. In particular, experiment has not yet decided whether it is due to the presence of small cavities and an increase in intergranular surface or to an actual expansion of the lattice itself. This uncertainty in the origin of the change in density is a reflection of our uncertainty as to the changes induced in a metal by cold-working. One school regards cold-working as a breaking up of the original grains into a large number of perfect crystallites somewhat randomly orientated with respect to one another.2 According to this viewpoint, the mere introduction of a large intercrystallite surface induces a net volume expansion. Another school regards cold-working primarily as a distortion of the grains. It is not obvious that this second viewpoint will lead to a net volume expansion. The purpose of the present paper is to show that this is indeed the case, and that this expansion is of the right order of magnitude to explain existing experimental data. The physical basis for the association of an expansion with distortion lies essentially in the variation of the elastic moduli with volume. This variation is considerable. Thus from Table I we see that a I per cent increase in volume for the case of copper will decrease the bulk modulus K by i0 per cent, the shearing modulus µ by 3.8 per cent. If we thus twist a rod through a given angle, we shall do less work upon it if it increases slightly in volume, thereby reducing the torsion modulus that involves as a factor the shearing modulus. A general principle' in physics states that the rod will so adjust itself as to have a minimum potential energy consistent with the end restraints. It will therefore expand. [ ] In order to obtain a quantitative comparison with experiment, we follow Maier4 in comparing the lattice expansion with the latent energy of cold-work. This latent energy has been measured directly by Taylor and Quinney5 on copper rods subjected to torsion, and may amount to as much as 15 per cent of the total work done upon the specimens. We shall assume that this

Jan 1, 1941

By F. C. Blickensderfer

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-On your trip today through the Inspiration and Miami mills you have seen in actual operation the machines which represent the changes adopted in grinding methods in the Miami district from the beginning of operations in March, 1911. In one section of the Miami plant are three Chilean mills not yet discarded, representing the first machines adopted. In another section, pebble grinding is still in operation, while in the balance of the plant, pebbles have been replaced with iron balls. In all cases these machines are handling a feed which is the product of roll, grinding down to about ¼ in. in, size. The latest step in grinding in the district, You saw at the Inspiration plant, where in Marcy mills a filed, the larger pieces of which remain on a 2-in. opening, is being reduced in one operation to a product of which only about 3 per. cent. remains on the 48-mesh screen. A detailed comparison of the methods used at the two plants would be very instructive but our own work at Miami has not yet reached a point where such a comparison is possible, the reason being that our final product is not yet fine enough. By means of larger Hardinge mills operating in closed circuit with Dorr classifiers soon to, be installed in one section of the plant, we hope to obtain, under properly balanced operating conditions the same end result as at Inspiration. It, might interest you, however, to know some of the results we have obtained here by the substitution of balls for pebbles. With pebble grinding, using three 8-ft. by 22-in. mills, followed by one 8-ft. by 66-in. mill for regrinding the coarse product of the primary mills, we handled 636 tons per 24 hr. in one section of the plant. Substituting balls for pebbles in the first operation and using two mills in place of three we obtained a tonnage of .714 tons to the section. With the use of balls both in the primary mills and in the regrinding mills, the tonnage for one section was raised to 822 tons per day. Coincident with this increase in tonnage, we also obtained a greater efficiency. The use of pebbles in all mills showed 21.5 per cent. plus 48-mesh material in the final tailing, which figure was reduced to 13.9 per cent. for balls followed by pebbles, and to 4.6 per cent. with the use of balls both in the primary and regrinding mills.

Jan 12, 1916