Search Documents

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944

By R. A. Perry

DURING 1943, supplies of lead, like those of most base metals, moved from a position of scarcity to one of ample supply for all possible war requirements. The principal worry in the market, as 1944 began, was that surplus stocks might increase too rapidly to maintain price stability. The problem of postwar stockpiling had definitely entered the picture. The end of the year finds the lead industry having met all use demands, but not without depleting stocks to a critical low in spite of heavy importations. The principal reason for this dangerously reduced stock position is lack of adequate man power, which, without question, has become the lead industry's number one problem. This condition became obvious about the middle of the year, after Selective Service placed in effect orders that no deferments would be given employees under 26 years of age, and to a complacent attitude toward the industry assumed by the War Manpower Commission. It has become progressively worse since then. The WPB continued its policy, started during 1943, of easing restrictions on materials to be used for maintenance, repairs, and operating supplies. The policy of premium payments established by the Metals Reserve Co. was continued and, in spite of expressions to the contrary, has proved quite satisfactory. In short, the Government continued its program of stimulating the lead industry in practically all

Jan 1, 1945

By Irving H. Wentworth

The little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map, Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90" in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. History. On the discovery of the silver-lead bearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of about 3 miles east and 5 miles west of the town. At the western extremity and near the Car-rolefia mine, a small town called San Pedro was huilt. The

Jan 1, 1913

By John C. Sawyer

A brief review is given to show that catastrophic oxidation of stainless steel in the presence of lead oxide is similar in many respects to catastrophic oxidation as caused by MoO3 and V2O5, Experimental data are presented to show that lead oxide accelerates the normal oxidation process of stainless steel by chemically altering the normally protective oxide film formed on the base metal. Data are given to show that similar reactions occur during oxidation of stainless steel in the presence of MOO3,and V2O5. THE mechanism by which pure metals oxidize at high temperatures has been the subject of intensive research for many years and much has been accomplished towards understanding the processes involved. The mechanisms by which alloys oxidize have also been investigated, but due partly to the fewer number of investigations and partly to the complexity of the oxide systems present, available knowledge is not as extensive as with pure metals. When oxidation processes are further complicated by atmospheres contaminated with sulfide, halide, or oxide vapors, the knowledge of fundamentals becomes meager or altogether lacking. Thus, it is not surprising to find that the catastrophic oxidation of stainless steels in metal oxide vapors of MOO, and V2O5 is not a well understood phenomenon despite the fact that a number of investigations have been undertaken. The literature in dealing with the subject of catastrophic oxidation is primarily concerned with the effects of MOO3 and V2O5, but does mention that other metal oxide vapors, one of which is lead oxide, appear to promote a similar type of accelerated oxidation. While this latter effect is virtually unknown, the deleterious effect of lead oxide is of considerable commercial importance, as it is believed to be one of the fundamental reasons for exhaust-valve failure in gasoline engines. For this reason studies have been in progress for many years attempting to better understand the mechanism involved. Modern exhaust-valve alloys"2containing 20 to 25 pct Cr plus nickel and/or manganese are in effect high-grade austenitic stainless steels exhibiting ex- cellent oxidation resistance in air at exhaust valve operating temperatures of 1100° to 1700°F; yet these same alloys are prone to corrode during engine service because of the conditions attending their operation. These conditions are such that the valves become coated with deposits of complex lead compounds mainly derived from gasoline additives of tetraethyllead, ethylene dibromide, and ethylene dichloride. Literature searches3-7 and discussions with various investigators show that considerable difference of opinion exists as to the nature of the lead-bearing deposits found on the surface of exhaust valves and the atmospheres to which they are subjected; yet, all seem to generally agree that corrosion, a gradual transformation of alloy to nonmetallic products of corrosion, is a consequence of the presence of lead compounds. This majority opinion seems to be substantiated by laboratory engine tests which show that corrosion does not occur to any appreciable extent when lead-free fuels are used. The first observations of catastrophic oxidation reported in the literature were probably made by pfeil,8 but it was Leslie and Fontana9 who undertook the first detailed study of the phenomenon. Their work was chiefly centered on the acceleration of oxidation which took place when stainless steels containing more than 3 pct Mo were heated in air with restricted circulation. These investigators reported that the presence of other oxides near the surface would further accelerate the rapid oxidation which occurred. While they recognized that the effect was attributable to the presence of molybdenum, it was Rathenau and Meijering" who emphasized the fact that the presence of molybdenum in the alloy was incidental to the presence of MOO3 vapor in the atmosphere surrounding the specimens. Evans,11 as well as Cunningham and Brasunas 12 studied similar

Jan 1, 1962

By C. C. Hawes

SILICA is the main impurity in iron ore. It is intimately associated with the iron oxide, sometimes free but more often in the combined state, as a mineral silicate. Its separation and purification sometimes present difficult problems to the analyst. In the absence of any definite knowledge to the contrary, orthosilicic acid. H4SiO4, is supposed to be the only silicic acid made, all other forms, such as metasilicic acid, H2SiO3, representing different degrees of its dehydration. These acids are exceedingly weak but form the most stable compounds found in nature. They are known as the silicate minerals and are formed by the combination of the different metallic oxides

Jan 1, 1936

James DouGlas, New York, N. Y. (communication to the Secretary*):—In my paper on the Conservation of Natural Resources, I referred to the slow replacement of bee-hive ovens by the by-product ovens as a most notable instance of waste. And I quoted from Mr. Parker's report for 1906 an explanation given by him in accounting for the small production of by-product coke. It was that the market for the by-products of the coke-ovens was so limited that some of the ovens constructed were out of operation. His report on the manufacture of coke in 1908' does not record an improvement, and attributes the strange fact that we alone, of all the industrial peoples, delay the adoption of this cardinal improvement from the continuance of the same almost inexplicable cause. To quote again from his report, he says (p. 241): "The year 1908 was not marked by any notable gain in the construction of byproduct coking plants, though some new work was done. There was a net increase

Jan 1, 1910

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

Denver, the Mile High, Queen City of the Plains, your host for AIME's 99th Annual Meeting has many exciting and picturesque places for you to visit during your stay. A host of restaurants cater to every taste; supper clubs and theaters provide nighttime entertainment; there are sports facilities and a plethora of shops for the ladies. When it comes to dining out, there are many excellent restaurants within walking distance of the Denver Hilton --among them, three in Brooks Towers: the Gitana, the Boston Half Shell serving the finest seafood, and Marvelous Mary's. In the Larimer Square area there in the Bratskellar with a true Germanic atmosphere and Sperte's Laffite offering a typical New Orleans setting.

Jan 1, 1970

By J. B. Knaebel, M. W. Von Bernewitz

OUTSTANDING FACTORS that have largely induced the current great interest in the reopening of old mines and the search for new deposits are the increased relative value of gold, the certainty of a market for it, and the decreased activity and poor profits in other lines of endeavor. It is easy to understand why a miner out of a job and unable to find any other means of livelihood would naturally take to the hills with his pan, pick, and shovel; but never before have inexperienced, would-be prospectors and placer miners materialized from the factories and farms, the haberdasheries, and the oil and gasoline supply stations, in such numbers as the last couple of years have witnessed, except when rich strikes of the proportions of a Klondike have been made. What, may one ask, has occasioned this condition? Unemployment has put these men in a receptive frame of mind, and newspaper and magazine articles have done the rest-- The Gold Miner of Los Angeles (a new weekly), The Mid- Week Pictorial (New York) for Sept. 3, 1932, and Popular Science Monthly for August, 1932, for instance. Even the Saturday Evening Post had an article on a promising part of Colorado. Stories that good wages may be had for the panning in nearly every western state have been featured by daily papers, popular "scientific" magazines, and quasi- technical journals. These tales have been eagerly grasped by thousands of people whose ignorance of mining has only served to increase their enthusiasm.

Jan 1, 1932

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

Mr. A. Bement, Chicago, Ill. (communication to the Secretary*) :—Mr. Campbell, in proposing his method of sampling coal-seams, has rendered an important service in insisting on the presentation of an adequate history of the sample; and it is to be hoped that his suggestion will meet with further recommendation. In my opinion it is fully as important that a complete description of the sample and the conditions surrounding its taking be given, as the results of the analysis itself; and if such should become standard practice, coal-analysis would assume greater value. As it is, the published data are very confusing, and only to an extremely small extent are they really useful. The method suggested by Mr. Campbell, however, cannot have a general application; for example, in the Eastern Interior coal-basin, particularly at the present time, the output consists largely in grades other than mine-run, which in Illinois, for the year 1905, was only about 24 per cent. of the total product; and inasmuch as Mr. Campbell's method of sampling cannot give values for any other grade than mine-run, my contention that, at best, it can have but a limited application, is apparent. To illustrate the argument, there are two coal-seams, with the characteristics of which I am particularly familiar; each seam, as it lies in the ground, contains almost exactly 10 per cent. of ash; the lump coal from one of these seams ranges from 10 to 11 per cent. of ash, but from the other seam it does not average more than 6 per cent., although, as before mentioned, the average percentage of ash in the full seam is the same for each case. A careful and proper sampling of coal-seams, to be followed by analyeis, is to be commended in connection with all investigation; in fact, it should precede any careful study. A serious error, however, may be made in attempting to use such results to set values on the product as shipped or received. The only

Jan 1, 1906

By K. Brack, G. H. Schwuttke

Annealing properties of subszerface amorphous lavers produced through high-energy ion implantation in silicon are studied. The buried layers are produced through the implantation of ions (nitrogen), ranging in energy from 1.5 to 2 mev. X-ray interference patterns, transmission electron microscopy, and resistivity profiling are used to study the annealing characteristics of the ion damage. The annealing experiments indicate a low temperature (below 700°C) and a high temperature (above 700°C) region. Significant changes occur in the amorphous layer during the high-temperature anneal. Such changes are corre-lated with the re crystallization of the amorphous silicon and the formation of subsurface (buried) silicon-nitride films. TODAY'S main problems in the field of ion implantation are related to the accurate determination and prediction of 1) the distribution profiles of implanted ions, 2) the lattice sites occupied by the implanted ions, 3) the lattice damage produced through ion implantation, and 4) the annealing characteristics of damage centers in the lattice. This paper reports investigations concerned with the problems listed under 3) and 4). EXPERIMENTAL Our investigations cover the energy range of incident ions from 100 to 300 mev and from 1 to 2.5 mev. The emphasis of this study is on the energy range from 1.5 to 2 mev. The experiments are conducted with single charged nitrogen ions. To implant the ions a van de Graaff generator is used as described by Roosild et al.1 Accordingly, a gas containing the desired ion specie is passed through a thermome-chanical leak into a radio frequency activated source. The positive ions are driven into the van de Graaff with the help of a variable voltage probe. Emerging from the accelerator the ions drift into a magnetic analyzing system and here the desired ion specie is bent 90 deg into the exit port. The ion beam leaving the analyzer is defocused and drifts down a 4-ft long tube to hit the silicon target. At this position the 20 pamp ion beam has a circular cross-section of 2.1 cm. N2 is used as a source gas for nitrogen ions. The implantation target is silicon with zero dislocation density, 2 ohm-cm resistivity, (111) orientation, mechanically-chemically polished, and 1 mm thick. The target is mounted on a water-cooled heat sink and kept at room temperature. A fluence of 1015 to 1016 ions per sq cm is used. RESULTS 1) Silicon Perfection after Bombardment. High-energy ion bombardment of silicon has some striking effects on lattice perfection. Some results were reported in detail previously at the Santa Fe conference2 and are here briefly summarized for the benefit of the experiments described in the following. 1.1) Identification of Surface Films on Silicon. After bombardment all samples are found to be coated with surface films. The films on the silicon surface vary in thickness and color; they can be transparent, slightly brown, or opaque. The films are thicker and darker in the high-intensity area of the beam and they delineate the bombarded surface area of the crystal. The films produce electron diffraction patterns characteristic of carbon and of SiO2. Carbon is predominant. The presence of carbon in these films was confirmed by use of the electron microprobe. Formation of the films occurs independently of the ions used and is attributed to a contaminated vacuum of the high-voltage machine. The carbon is most likely the product of the pump oil which is cracked and polymerized under ion impact. The films stick tenaciously to the silicon surface and burn off in a low-temperature Bunsen flame. 1.2) Mechanical Perfection of the Silicon Surface. The mechanical perfection of the bombarded silicon surface was investigated through optical microscopy, electron microscopy in which the replica technique is used, and optical interferometry. No mechanical damage of the surface was visible after bombardment. However, if a bombarded sample is soaked for several minutes in hydrofluoric acid (HF), gas bubbles may develop in certain spots of the silicon surface. It is also noted that in these areas the surface film starts to peel off. Relatively large patches of film come off if the sample is soaked in HF during ultrasonic agitation. After HF treatment, pits may be present on the silicon surface. The pit dimensions are estimated to be as large as 50 µ. The pits appear in the region of most intense irradiation. 1.3) Lattice Perfection After Bombardment. No lattice damage is found on the silicon surface. Electron transmission micrographs and selected area diffraction patterns of the surface show no difference before and after bombardment. Measured approximately 2 µm down from the surface, the silicon lattice throughout this depth is of good perfection. Well-defined Laue spots and Kikuchi lines are obtained from the surface as well as from the indicated area below the surface. However, some radiation damage is dispersed in this top layer. A sharp boundary line separates this surface layer from a highly damaged layer which extends further downward into the silicon. Typical of this

Jan 1, 1970

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.' I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker's hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By L. J. Gurevich

IN the course of the examination, at the Bureau of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undertaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the Jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed."

Jan 8, 1919

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By AIME AIME

WILLIAM ("BILL") EMBRY WRATHER, recently elected to a second term as Director of the Institute, is widely known as petroleum geologist, gentleman, and scholar. Born in Brandenburg, Ky., he was early endowed with a Southern accent which has remained with him strongly flavored by his later life in the oil-fields of Texas and the Mid-Continent region, and only thinly concealed by a Middle Western burr acquired during his student days at the University of Chicago. After graduating there with the Ph. B. in 1908, young Wrather (the adjective still fits!) joined the Gulf Production Co. Soon afterwards he married a charming Chicago girl, Alice Dolling, who, with their two daughters, has been his companion on many of his more distant trios.

Jan 1, 1945

AlbioN S. Howe, San Francisco, Cal. (communication to the Secretary*):—In discussing this paper, 'I mould suggest that. the dip for iron pipe be liquid asphaltum, instead of coal-tar and pitch. Asphaltum is superior to coal-tar, and the variety

Jan 1, 1905

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By J. F. Myers

AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of -200-mesh produced a very creditable figure.

Jan 1, 1950

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966