Search Documents

By F. Julius Fohs

TAKING into consideration the present state of geologic knowledge and present economic status of the oil industry, we have attempted to outline the six principal districts in which oil occurs and new pools may be expected. The map, Fig. 1, also shows the location of the present productive pools-about 100 in number. The unshaded areas represent territory where drilling depths to known sands are prohibitive with present development and pumping methods, or such sands are absent or give promise of such small production that deep wildcat tests are unwarranted. They include, also, territory where the oil-source materials are absent or not of the right type; and where shales are insufficient in the stratigraphic section to prevent the escape of oil and gas. Some doubtful districts are also included, such as the Pecos Valley, where the percentage of rigid beds, sandstones and limestones may be too great; and the Nacogdoches oil field, where small shallow production is obtained but where deep or large production is unlikely. The map is not offered as final but in the hope that it may prevent the expenditure of large sums in attempted development of unlikely territory and as the warning that those who drill in the unshaded territory do so at great risk. Those who drill in such territory should have large sums available for pioneering and experimenting and only attempt it if they can well afford to lose the money expended. Search in the shaded or cross-hatched areas is hazardous enough and should only be undertaken after detailed geologic surveys. Out of a total area of 256,000 sq. mi., the oil and gas districts comprise about 80,000 sq. mi.; the territory embraced in these districts is shown in the shaded portions. This may ultimately be increased somewhat by the addition of some minor districts, but such additions will be offset by territory probably now included in the unshaded areas. The shaded areas probably contain 98 per cent. or more of the ultimate production of the state, despite the fact that they represent only 31 per cent. of the total area.

Jan 3, 1924

By William E. Ford, Edward Salisbury Dana

Normal phosphoric acid is H3P04, and consequently normal phosphates have the formulas R3PO4, R3(P04)2 and RPO4, and similarly for the arsenates, etc. Only a comparatively small number of species conform to this simple formula. Most species contain more than one metallic element, and in the prominent Apatite Group the radical (CaF), (CaCI) or (PbCI) enters; in in the Wagnerite Group we have similarly (RF) or (ROH).

Jan 1, 1922

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which; if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its. use is, however, confined to a person having skill in the. manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms-the call-bell-has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanehé cells, two or more electric bells, and a mile or more of wire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator's input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It's almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By G. Adel, J. Richard Lucas, C. Haycocks

This paper describes over sixteen computer programs developed at Virginia Polytechnic Institute and State University during the past twenty years to assist in the design of coal operations. Overall development concepts in the construction of the programs are outlined, commencing with those used in the exploration phase of mining and extending through economic analysis and into the design of specific engineering systems such as belt, rail and power networks, scheduling, rock mechanics problems and simulation of face systems. Summarized information is given for the use of the major programs including user restrictions, input data, typical output and industrial applications and case studies. Analysis has been made of the programs' applications by industry throughout the world. Such analysis is facilitating development of new programs as well as a refinement of existing ones. To date programs have been constructed in four categories: exploration, ground control, economic and simulation. Face production simulations are stochastic in nature and require the use of time study data obtained at sites underground. Future programming efforts currently under development are aimed at interactive programs for use with minicomputers and, where advantageous, with graphical displays.

Jan 1, 1983

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

By John H. Hollomon

IN recent papers, O'Neill,1 Vivian,2 and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: [e = In A t][I] where a is the strain and Ao and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is plotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept is very fruitful and should be kept in mind in any study of the deformation characteristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite number of specimens, each with a different strain history determined by the preceding part of the flow curve. Each of these specimens can also be considered to have a fracture strength. Unfortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By Ferdinand H. Regel

Concentrating-machinery has been wonderfully improved during the past few years both in technical efficiency and in economy of power; and, in the writer's opinion, the prosperity which the mining industry has of late enjoyed is due in large part to this improvement. Many properties are yielding handsome profits at the present time which were considered, a few years ago, too low in grade of ore to be profitably operated; and I think that fully half of these once worthless properties owe their successful development to recent improvements in concentrating-machinery. The present paper calls attention to a jig and an ore-classifier of new design, invented by Mr. John Klein, and already used in the lead-region of SE. Missouri, and in the Philipsburg dis-

Jan 1, 1902

pAbad, Leopoldo F., Min, Engr,, Div. of Mines, Bureau of Science Manila, P. 1. '23 Abadilla, Quirico A,, Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela, '20 Abbey, Robert Graham, The W. W. Sly Mfg, Co Train Ave., Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Mexico, '28 Abbott, Clarence E., Mgr., Mines & Quarries, Tenn, Coal, Iron & R. R, Co,, 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By J. W. Downey, M. V. Nevitt

MUELLER and Knott' have reported that Ti2Cu has the Si2Mo-type (Cllb) structure. The lattice parameters of Ti2Cu and the positions of the titanium and copper atoms are given by them as follows: ao = 2.944A; co = 10.786A 6 atoms per unit cell: 2 Cu (a) 000; 1/2: 1/2, 1/2 4 Ti (e) 002; 1/2, 1/2, 1/2 + z 00 -2 ; 1/2. 1/2. 1/2- z where z = 0.341 We have found eight other binary compounds which appear to be isostructural with Ti2Cu. All of them involve the combination of a titanium group element with a copper group element or a titanium group element with palladium. The compounds and their lattice parameters are given in Table I. The alloy samples were prepared by arc melting metals having a purity of 99.9 pct or better. They were homogenized for 72 hr at 900°C in evacuated capsules and quenched in tap water. Filings were prepared, and these were reannealed for 4 hr at 700°C, also in evacuated tubes. The lattice parameters were determined by a least squares Bnalysis of the back reflection lines of patterns made with cobalt radiation. It was not possible to make a precise determination of the lattice parameters of Zr2Au because the filings underwent rapid oxidation at room temperature. The evidence supporting the large tetragonal cell containing 6 atoms involves the presence of the reflections 002, 101, 004, 112, 114, 202, and other reflections with higher indices for which I = 3n. Three or more reflections corresponding to these indices, which cannot be indexed on the basis of a small body-centered tetragonal cell containing 2 atoms, are observed in the patterns of all of the compounds listed in Table I. They are strongest and most numerous when the components have large differences in their atomic scattering factors, as is the case in Ti2Pd, Zr2Cu, and Hf2Cu. The values of the z parameter should be regarded as approximate They were selected on the basis of the best agreement between the observed intensities of two pairs of closely spaced powder pattern lines (004): (112) and (114): (202) and the corresponding intensities calculated for several values of z. An ordering scheme was assumed in which titanium, zirconium, or hafnium atoms occupy the titanium positions of Ti2Cu, and copper, silver, palladium, or gold atoms occupy the copper positions. Calculated and observed intensities of the aforementioned lines and the other lines of the patterns are in satisfactory agreement, but a refinement of the z parameters and a final confirmation of the ordering arrangement must await a more detailed study. It is interesting to note that in transition metal systems at A2B stoichiometry the Si2Mo-type structure competes for stability with two other fre-

Jan 1, 1962

By Bruce W. Gonser, A. U. Seybolt

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By A. U. Seybolt, Bruce W. Gonser

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By R. J. Batterham, P. W. Roller

Granulated sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. Pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors. It was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of shape factor values with the amount of water used for granulation is examined in relation to the strength of granules of the sinter mixes. The experimental and mathematical techniques presented may be useful in interpreting the behavior of the permeability of sinter beds after ignition.

Jan 1, 1986

By G. B. Gibbs

Various semiempirical equations which relate defect-formation energies and entropies with elastic and thermal properties of a metal crystal are shown to be related by a simple model for lattice energy. An illustrative comparison of theory with experiment is made using self-diffilsion data for fee metals. SEVERAL workers have related the free energy of defect formation with elastic and thermal properties of a crystal lattice, particularly elastic bulk modulus and Debye temperature. The present note shows how the various approaches are related by a simple model for lattice energy. A comparison of theory with experiment is given using the self-diffusion parameters of fee metals. 1) A MODEL OF THE CRYSTAL LATTICE The internal energy per atom in a metallic lattice may be written U=Ui-Ue [1] where Ui and Ue refer to ion-ion interaction and valence electron energies, respectively. The volume per atom V has an equilibrium value 52 for which

Jan 1, 1968

Jan 1, 1942

Jan 1, 1942

By M. Semchyshen, G. A. Timmons

P. A. Beck (University of Illinois, Urbana, 111.)—An interesting result of this work is the fact that in cold rolled molybdenum sheet complete loss of work hardening is obtainable on annealing, without change in texture. The retainment of the cross-rolling texture on soft-annealing is particularly significant, since this is essentially a single orientation texture, where texture retainment could be achieved by only one of the two niechanisms which produce this effect in aluminum,16 namely by recrystallization in situ. Recrystallization in situ was originally discovered by Collins and Mathewson (1940) and by Crussard (1944) as a phenomenon taking place on annealing in relatively mildly deformed single crystals of aluminum. It now appears to be a major (in many cases the major) mechanism of annealing of severely cold rolled poly-crystalline material, not only in aluminum,le but in metals as different in character as beryllium," tita- nium,'" and molybdenum. All these data now confirm the general validity, at least for more or less pure metals, of the interpretation of the annealing process given a few years ago by Smith.'" The whole question of recrystallization is now reopened. Indeed, it appears that recrystallization, as defined traditionally, may not occur at all, since at the time "deformed material" is absorbed by "recrystallized grains," it has already become completely strain free by recovery and "recrystallization in situ."

Jan 1, 1953