Search Documents

By Charles H. Jacoby

During the past three decades an ever increasing number of uses for underground storage space has been developed. In some instances, the value of the space created has been so great that the host rock has been wasted. The preferential use of salt to host underground cavities is based on numerous factors, the primary two being low extraction costs and low permeability. Both dry and solution mined cavities have been created for the storage of a variety of materials. As the demand for underground storage and disposal grows, so must our selectivity of the materials to be stored.

Jan 1, 1985

By S. K. Nicol, A. R. Swanson, J. C. Day

Addition of oil to a suspension of hydrophobic coal particles can influence its dewatering characteristics. An agglomeration process occurs in which coal particles are held together by negative capillary pressure at particle/oil/water contacts. Consequently, the units round which flow can occur are enlarged and this improves dewatering parameters such as drainage rate, solids recovery, and equilibrium moisture content. This paper discusses processes which attempt to use this principle, in terms of metallurgical and economic efficiency. The discussion is augmented by results of recent experiments on the effect of oil addition to centrifuges and vacuum filters.

Jan 1, 1980

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972

By J. A. Herbst, D. W. Fuerstenau

An analysis of the kinetics of dolomite grinding in a dry ball mill reveals that the following approximations apply for the parameters of the batch grinding model: (1) the size discretized selection functions are proportional to the specific power input to the mill, and (2) the breakage functions can be taken as invariant. These approximations are shown to provide the basis for accurate predictions of product size distributions obtained for several mill speed, ball load, and particle load combinations within the normal ball mill operating range. The engineering implications of these findings are discussed.

Jan 1, 1974

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By C. R. Hocott

THE viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,1,2 but no data have been published on the viscosity of repre-sentative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields.

Jan 1, 1940

By R. V. Norris

In a former paper on this subject,' I summarized Murgue's theory and experiments, and presented a large number of tests of mine-fans, stating some conclusions, " more or less warranted by the evidence," as to design, capacity and efficiency. Since that time the very valuable report of Mr. M. Walton Brown: Committee on Mechanical Ventikators, Institution of Mining Engineers, has appeared, and I have made additional experiments which tend to clear up some points in connection with this subject. Design and Tests of the Luke-Fidlbr Colliery Fan. The Luke-Fidler fan (see Figs. 1, 2 and 3), built to replace an old wooden fan at a very fiery colliery, presents some pecu-

Jan 1, 1905

By H. M. Strong, R. A. Oriani

THE technological interest attaching to light, age-hardening alloys for structural uses has been pointed out to one of us.1 A potentially interesting alloy would be titanium-rich Ti-Mg alloy, provided that sufficient solid solubility exists. or could be induced at high pressure. and provided also that age hardening can be induced by proper temperature and/or pressure annealing. It was decided therefore to explore the feasibility of producing a Ti-Mg alloy in the high-pressure apparatus. Experimental. Three high-pressure runs have been carried out. In each case the geometry of the sample was that of a cylinder of titanium of commercial purity, into which a narrow hole had been drilled along the axis; this hole was filled with magnesium wire,

Jan 1, 1967

During the past 20 years the Westinghouse Electric & Manufacturing Co. and the General Electric Co. have collected a valuable library of some 9000 volumes on electricity. The collection was intended especially for use in patent searches and is particularly rich in patent material. Files of all the principal patents relating to electric light acid power issued by America, England, France and Germany, are present, together with copies of the patents owned or controlled by the two companies. Another feature, and one of unusual value, is a series of volumes containing the records of the important adjudicated patent cases of these companies and their predecessors during the past 25 years, and forming a storehouse of electrical history. There are also files of about 100 electrical periodicals. It is a pleasure to announce that this collection has now been presented by the owners to the Engineering Societies Library. This gift, which was arranged through Mr. Charles A. Terry, Vice-president, Westinghouse Electric & Manufacturing Co., and Mr. Charles Neave, Counsel,

Jan 7, 1918

The opening session of the A. I. M. E. was held at the King Edward Hotel, Toronto, on Tuesday, July 25th. Dr. W. G. Miller, on behalf of the Local Committee, opened the proceedings. [ ] President John Hays Hammond, who occupied the chair, introduced Alderman Graham, Chairman of the Reception Committee, and representative of the city, in the absence of His Worship the Mayor. A brief address of welcome was delivered by the Alderman and responded to by President Hammond. The President then requested Dr. James Douglas to present to the honoured Secretary of the Institute, Dr. Rossiter W. Raymond, an oil portrait.

Jan 1, 1907

By B. F. Tillson, C. M. Haight

I. General Remarks..........................723 1. Location............................723 2. Characteristics of the Orebody..................725 (a) Mineralogical (b) Shape, Strike, Dip, Size, Etc. (1) Ore (2) Country Rock 3. Historical Sketch........................725 11. Mining Method..........................726 1. Outline of Methods Now in Operation............... 726 (a) Stopes (b) Fill . (c) Pillars (d) Slices (e) Transportation (f) Miscellaneous 111. Mining Operations........................727 1. Shaft..............................727 (a) Sinking (b) Dimensions and Equipment, Sketches (1) Size, Inclination. Direction, Etc. (2) Timbering (3) Stations (4) Track (5) Hoisting Equipment (a) Skips (b) Engines and Ropes (c) Idlers (d) Man Cars (6) Loading Pockets (a) Operating Figures (7) Headframe

Jan 1, 1918

By Charles L. Bauer

WHEN a single crystal is annealed following plastic deformation recrystallization usually occurs rather than polygonization. Consequently, re-crystallization has received the overwhelming amount of attention albeit the intrinsic mechanisms by which dislocations rearrange and annihilate one another are just as well revealed by crystal polygonization. It is the purpose of this note to demonstrate the usefulness of studying the polygonization process by means of an etch-pit technique in sodium chloride. Sodium chloride deforms easily (the slip system is of the [110], (110) type), readily cleaves on (100) planes, and can be chemically etched so as to reveal the intersection of dislocations with a free surface. Thus it is possible to observe the distribution of dislocations after a crystal has undergone a specific deformation and annealing cycle. Various phases of the polygonization process

Jan 1, 1965

By James B. Cathcart

Marine phosphorite deposits occur in Braxil, in the Bambui Group of late Precambrian or Early Cambrian age. The phosphorite is laminated, isoclinally folded, and is composed of black, elongated apatite pellets and quartz grains cemented by quartz and muscovite. Abundant, narrow quartz veinlets cut through the .rock at right angles to the elongation direction of the pellets. The phosphorite is 0 to 80 m thick and contains 5 to 30 percent P2O5. The deposit is elongate towards the northeast, and the central, thickest, and richest part is bounded by faults. Measured reserves are about 250 million tons that average a bout 13 % P205. Preliminary testing indicates that grinding, scrubbing, and desliming will produce a material usable for fertilizer manufacture at a cost competitive with imported phosphate fertilizers.

Jan 1, 1979

By John Cobb

THE attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinations of ,the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia, at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal, and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in another way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 3, 1925

By John W. Cobb

The attempts of British investigators to arrive at definite knowledge concerning the nature of the nitrogenous constituents of coal have been mainly made through studies of the behavior of coal on carbonization and gasification. There have been carried out numerous determinitions of the distribution of nitrogen in the products of carbonization under laboratory and large-scale conditions; and by a careful consideration of the extent to which nitrogen is liberated, say as ammonia,. at different temperatures and under different conditions of operation as regards atmosphere, it has been possible to form some general notions as to the nature of the nitrogenous compounds present in the coal; and at the same time to arrive at clearer ideas as to what are the important operative factors in determining the ammonia yield under working conditions. This work has been spread over many years and is summarized below. The difficulties of connecting the results in such a way as to allow of the nitrogenous constituents of the coal being described in terms of specific organic structure are great. They arise, for example, in the carbonization process, because the phenomena of decomposition observed at any one temperature can only refer to compounds decomposing at that temperature, each of them with a previous history of chemical transformations occurring at lower temperatures. To put it in &other way, the compounds occurring in the coke at any stage are not in the least likely to be those present in the original coal. The same difficulty, in a milder form, occurs when the method of differential solution is attempted. There is always the preliminary question, almost impossible to answer, as to how far the separation by the use of the solvent has involved some form of decomposition of the original compounds. In the following summary, an attempt has been made to bring together results obtained by British workers.

Jan 1, 1925

By C. H. Johnson

THE year 1952 has seen the continuance of the trend pointed out by Tell Ertl in this magazine a year ago, toward mechanization in metal and mineral mines. Outstanding progress has been made in the adoption of rock bolting in situations where, a short time ago it would have seemed inapplicable. New devices, better equipment, and improved practices are in part responsible for shifting fashions in mine development, stoping methods, and transportation systems. Only new mines, of course, can take the advantage of the new ideas that are being tested and demonstrated throughout the industry, but the old mines often show a surprising adaptability

Jan 2, 1953

By Alvin Kaufman

ANTHRACITE mining in the United States is concentrated in a 480 sq mile section of north- eastern Pennsylvania. The producing area is broken up into four fields, known as the Northern, Southern, Eastern Middle and Western Middle fields. These areas represent intricately folded coal measures in synclinal residuals left by erosional forces. Destruction by erosion has eliminated some 95 pct of the original coal. However, discounting the 5 billion tons removed to date, 8 billion tons are believed to be still recoverable.

Jan 3, 1953

By Theodore M. Barry

Work measurement is the most common of many titles given to determining the amount of human work required to do any job. A new technique-like most modern management tools-it still needs years of constructive research. Yet despite known imperfections, it is probably the most enthusiastically used tool of cost control developed in the last hundred years. Over 85 pct of all companies employing more than 100 workers in one of the major industrial areas use work measurement. For a good reason, however, this has not been true in the mining industry until very recently. The facts make an interesting story.

Nov 1, 1955

By W. C. Hazen, A. V. Henrickson

URANIUM plant operations of the Kerr-McGee Oil Industries at Shiprock, N. M., began in December 1954. As originally designed, the plant treated Plateau carnotite ores by the acid cure process, which dissolved both uranium and vanadium minerals. After 16 hr of acid curing, the ore was conveyed to an agitator and leached for 2 hr in acid liquor at a pH of 1.0. The leach pulp was then separated at 100 mesh in a classifier, the sands continuing through a washing classifier circuit and the slimes going to a countercurrent decantation system of four thickeners.

Jan 9, 1957

By J. R. Slotemaker

As successfully pilot-tested at a quarry producing limestone for a large cement plant, swiftly flowing streams of rock enter the Gromax Selector. They are electronically scanned while in motion and light reflection data flashed to logic circuits. The logic circuits compute the total light deviations in each rock as it passes the scanner. Thus, a rock with striated or spotted impurities can be rejected or accepted on the basis of its proportional content. The actual case history of this equipment's development at a limestone quarry in the Southeast serves to illustrate its general area of usefulness.

Jan 1, 1964