Search Documents

By J. F. Kemp

CONTENTS. [ ] I. INTRODUCTION. 1. Situation.-From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway, which connects Monterey with Tampico, follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares, and from Linares one can see far away to the southeast the peaks of another group of mountains

Jan 1, 1913

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By H. F. Easter

The lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly on a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but. of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been due partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lcad or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted leady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. his matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is done by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 1, 1916

By Oscar A. Glaeser

THE mine and plant of the United Verde Copper Co., located in Yav-api County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level. The underground mining operations extend from the 300 to the 3000-ft. level. There are about 45 stopes in active operation on the 17 levels

Jan 1, 1929

By Keijiro Nishio

At a time of great antiquity when our Yomato tribe had not yet found its way throughout the country, there lived in Japan barbarous tribes of the stone age, whose dwellings were vertical caves covered with roof's of twigs and weeds. In a cave lately discovered at the village of Morita, 10 miles west from the port of Aomori, there were found pieces of micaceous iron-ore and psilomelane, with oval holes pierced from both sides. Apparently these objects were regarded as ornaments or curios, without being applied to any practical use. Among the traditions given in the Nihonshoki, an ancient history of Japan, there is one relating to the mining industry. According to this tradition, in the mythological age Izanami-no-Mikoto gave birth to Kanayamahiko-no-Mikoto, god of mines, and Amaterasu-Okami (the sun-goddess) was armed with swords. It came to pass at one time that she concealed herself in Ama-no-Iwato ("Heavenly Cave"), and several gods made contrivances to entice her out. Among them, Ishikori-dome, a smith, made a mirror with copper obtained from the Ama-no-Kagoyama, by means of a pair of bellows known as the Ama-no-habuki, which was made of a deer-skin. It is recorded also that Susanb-no-Mikoto, her younger brother, observed the abundance of gold and silver in Korea, where his descendants were to reign, and urged them to provide themselves with boats to convey them across the Sea of Japan. In the course of time he accomplished his object, proceeding to Korea with his son, Isotakeru-no-Mikoto. These accounts

Jan 1, 1913

By A. Tobey Yu

Despite its inherent low Btu content, western coal's low sulfur content may provide a near-ideal answer to satisfy US goals for clean air and energy self-sufficiency. Vast reserves, amenable to low-cost strip mining, serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be obvious, is the transportation cost. These deposits are remote from the utilities of the heavily populated eastern regions of the US (Fig. 1). A coal mine in Montana is likely to be more than 1500 miles from its utility market, while an eastern coal mine may be situated only 200 miles away. Thus, the question raised is: how can the haulage cost of western coal be substantially reduced to an acceptable level?

Jan 7, 1975

By E. DeGoyler

The Furbero oil field lies in the Gulf coastal plain of Mexico between the important ports of Tampico and Vera Cruz and about one-third of the distance between the two points from the latter (Lat. 20" 22' N., 97" 30' W. Gren.). It is in the State of Vera Cruz, about 14 miles west by south of the village of Papantla in the canton of the same name, and is the most southern of the developed oil fields of the Tampico-Tuxpam region being a distance of 50 miles south by east from the Potrero del Llano field and 42 miles in the same direction from the Alamo field. The field has been developed by the Oil Fields of Mexico Co. and is in the midst of a large block of lands owned or leased by them. Communication is through the port of Tuxpam with which it is connected by a narrow-gauge railway and 6-in. pipe line some 52 miles in length. This field is of more than ordinary interest since it represents a type of oil deposit hitherto unknown. So far as I am aware, no other commercially valuable deposit of oil is known to occur under conditions of accumulation similar to those found here. The igneous nature of the so-called 'sand' encountered in drilling was not recognized until a number of wells had been drilled; and it was not until recently that the geological relations of the sill or laccolith, which gives rise to the accumulation of oil, were known and the so-called 'anticline' was known to be, in part at least, the result of igneous intrusion. Geological surveys in this general region were made in 1900-1901 by W. H. Dalton and in 1907-1909 by P. C. A. Stewart, F. W. Moon, Leonard V. Dalton, and Dr. Max Muhlberg. More recent surveys have been made, however, under the direction of the author, by E. L. Ickes, B. C. Belt, B. Hartley, and Harve Loomis. Notes of the earlier examinations were not available with the exception of the report by Dr. Muhlberg who apparently first recognized the true nature of the Furbero intrusion. This paper is indebted to his work and that of the more recent surveys for much of the detail regarding stratigraphy and to Messrs. Percy Furber and Arthur C. Payne, President and General Manager of the Oil Fields of Mexico Go. for permission to publish, and for much of the in-

Jan 1, 1916

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

A GIFT of $10,000 to the endowment of Engineering Foun-dation, made by the Central Hudson Gas and Electric Corporation, has been announced. In transmitting this gift T. R. Beal, president of the corporation, made the follow-ing interesting statement: "You may be interested to know that this amount was in fact earned by our employees by their more efficient opera-tion of the physical properties under their care. It rep-resents $10,000 of return premiums paid during the past year on accident insurance, as the result of the company's excellent record in preceding years, so that we take greater satisfaction in making this gift as it is related, in some degree at least, to the higher standards of engineering and operating practice to which the work of the Foundation per-tains."

Jan 4, 1928

By Arthur Notman

SacRamento Hill is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the masa of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chal-cocite with associated carbonates as stringers in a mass of strongly brccciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or SO places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface obscrved in the other disseminated deposits of the Southwest.

Jan 1, 1916

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region [ ] This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 in. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine--almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies,

Jan 1, 1950

By Charles M. Packer, Oleg D. Sherby, Roy H. Johnson

Originally round tensile specimens of a eutectic Zn-A1 alloy develop elliptical cross sections during superplastic deformation. This observation, coupled with a detailed study of the microstructure and preferred orieniation, suggests that crystallographic slip and continuous grain boundary migration or re-crystallization are important processes during super-plastic deformation. In spite of the extensive activity in superplasticity1-15 and the numerous explanations proposed, no single model has had universal acceptance. It has been established, however, that the general requirements for superplastic extension of two-phase alloys include an extremely fine, stabilized grain size of the order of a few microns, a temperature about equal to or greater than one-half the melting point, a critical range of strain rate, and a similarity in the mechanical strength of the major phases. The proposed models can perhaps best be characterized in terms of the important phenomena associated with them. These phenomena include: phase instability,1 diffusional creep by volume diffusion3 or grain boundary diffusion4,5 slip and continuous grain boundary migration or recrystalliza-tion,= grain boundary Sliding,7-9,13,14 and dislocation glide.'5 In this paper, experimental observations will be reported which support a model involving slip and continuous grain boundary migration or recrystalliza-tion. Specifically, a correlation will be made between this model and the development of elliptical cross sections as originally round specimens are superplas-tically deformed. For the most part, superplasticity studies have been conducted with eutectic or eutectoid alloys. Probably the most thoroughly studied material has been the monotectoid Zn-A1 alloy.1,2,6,12,13,15 No attention to the eutectic Zn-A1 alloy has previously been reported, and the results discussed in this paper represent part of a general study of the superplastic properties of this alloy. MATERIALS The alloys used in this investigation were prepared by melting appropriate quantities of 99.99+ pct A1 and 99.999 pct Zn in air, mixing, and pouring into a water- cooled stainless-steel mold. Wet-chemical analysis was conducted with each heat of alloy prepared, using the procedure of Fish and smith.16 The composition of the eutectic alloy was 95.1 wt pct Zn. Ingots about 2 in. thick were rolled to 0.4-in. plate at about 300°C with a reduction of 5 to 10 pct per pass. Specimens were machined from the plate with the tensile axis parallel to the rolling direction. The specimens were round, with 0.150-in.-diam, 1.25-in.-long gage length, and 0.25-in.-diam threaded grip sections. EXPERIMENTAL PROCEDURE Specimens were mounted inside a uniform-temperature quartz tube which was surrounded by a double elliptical radiant furnace with a 12-in.-long uniform-temperature hot zone and a low thermal capacity. The tube extended through the top and bottom of the furnace and permitted rapid quenching of the loaded specimens when quickly filled with cold water at the conclusion of the test. The quench precluded any effects on specimen microstructure from a normal, slow cool. Constant stress was applied to test specimens by suspending a load on a constant stress cam of the type described by Hopkin.17 The design of this cam permitted application of a constant stress for elongations up to 200 pct. For greater elongation, approximately constant stress conditions were maintained by systematically reducing the load manually. RESULTS As part of an investigation of the superplastic properties of the eutectic Zn-A1 alloy, evidence was obtained for the development of elliptically shaped cross sections as originally round specimens were extended. For example, after an elongation of about 100 pct, a round specimen with an initial diameter of 0.150 in. became elliptical with major and minor axis of 0.128 and 0.88 in., respectively. Photographs are presented to illustrate the ellipticity developed during superplastic deformation, Fig. 1. The specimen shown was deformed at a stress of 500 psi, at a temperature of 285°C, and a strain rate of 2.28 x 10-2 min-1. The strain-rate sensitivity exponent* was measured at *The strain-rate sensitivity exponent, m, is defined as d In o/d In c where o is the steady-state flow stress and E is the strain rate. this temperature and in the strain rate range 10"3 to 10-1 min-1 was found to be about 0.5. This value is typical of those observed with superplastic materials. The material studied exhibited negligible strain hardening during superplastic deformation, the creep rate remaining constant under constant stress and temper-

Jan 1, 1969

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913

By W. L. Honnold

Owing to a unique labor situation and other unusual circumstances, the mining methods of the Rand are hardly comparable with practice elsewhere. They are of considerable interest, however, and their importance is increased by the magnitude of the' industry with which they are identified, gold of $166,186,000 value, say 40 per cent. of the world's production, having been recovered from 25,701,954 tons of ore milled in 1914. In the sketchy remarks to follow, attention will first be drawn to some influential factors of general bearing, after which certain features at two mines of the writer's group will be referred to. It is hoped that engineers associated with similar or different conditions and practice will contribute to broaden the discussion. Before proceeding, recognition is due the generous assistance of C. E. Knecht and F. A. Unger. General Observations The principal mines are situated along the northern limit of an irregularly shaped geological basin, and extend in almost unbroken continuity over a distance of about 60 miles. As the boundaries are defined by vertical planes there are both "outcrop" and "deep-level" properties, all differing in size and in technical features. So much has been written in regard to the geology of the Rand that only a few pertinent features need here be recalled. Briefly, the ore deposits are profitably enriched portions of certain conglomerate beds or "reefs," rarely more than three, which are interposed between quartzite, or quartzite and slate, and lie so closely together that where more than one are mined they are dealt with as a working unit, although they may be stoped separately. Their collective extension is locally referred to as " the Reef." Along the outcrop the series dips more or less steeply, and in depth it flattehs, the latter tendency being most marked in the Far East Rand, where the bottom of the basin is nowhere so deep as to be inaccessible. Dikes and faults are a common feature throughout. They are,

Jan 1, 1916

By Allan J. Clark

It is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper1 read before the Institution of .Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders. In the same way, as attesting the usual balance of such variations of different ores, it may be noted that the needle-like fibers of hornblende (cummingtonite), interlacing throughout the mass, render the ore more difficult to crush than would be anticipated, but on the other hand assist

Jan 1, 1916

By F. W. Bloecher, A. M. Gaudin

H. H. Kellogg—There is one point that the author has failed to emphasize sufficiently in his paper. What is commonly called the equilibrium contact-angle (the author's "maximum contact-angle") can have only one value on a smooth, flat, homogeneous surface under a given set of conditions. The equilibrium contact-angle is defined, for such a system, as the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By F. W. Bloecher, A. M. Gaudin

H. H. Kellogg—There is one point that the author has failed to emphasize sufficiently in his paper. What is commonly called the equilibrium contact-angle (the author's "maximum contact-angle") can have only one value on a smooth, flat, homogeneous surface under a given set of conditions. The equilibrium contact-angle is defined, for such a system, as the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By Don C. Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim their own metallic wastes. MAGNITUDE OF THE MODERN INDUSTRY No particular thought is given to the kitchen accident whereby a ruined saucepan is sorrowfully tossed into the ash can, yet it is a fairly safe guess that within a month this saucepan, together with hundreds of its fellows, will again be in service, perhaps in an automobile crankcase, or in an electric vacuum sweeper. It is by this conversion of the useless into the useful, whether from home or large manufacturer, that the secondary tonnage is built up.

Jan 1, 1928

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939