Search Documents

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By C. C. CONCANNON

POTASH is an essential. It is necessary as an ingredient in fertilizers or as a plant food, and certainly one of the great problems, and one of increasing gravity, is the maintenance of agricultural fertility that we may have adequate food supplies. When one thinks of potash one thinks of Germany. The first and most important deposits of soluble potash salts were found in Germany, and it was through Ger- man research and the application of a highly developed knowledge of chemistry that the value of these deposits was recognized and appreciated in the field of agricultural fertilization. The Germans knew that they had something of great value in their potash resources, not only because of the advantage derived from the extensive use of it in their own intensive farming operations at home, but also because of the pressing need for it on the part of other countries. Appreciating the economic value of this in international trade, they fostered the industry to the fullest extent and devoted much attention to well organized propaganda designed to bring out the essential need for potash of German origin throughout the world. Thus every one came to believe that potash was an essential commodity of only German origin and as such it held an extraordinary position in world trade prior to 1914.

Jan 1, 1926

By Joseph Jensen

CURTAILMENT of oil production in California began in 1922 and 1923 when certain of the major companies completely shut down some pumping properties. Efforts of this kind were generally carried on without coordination by individual companies until 1923. From May to August of 1923, oil production in the Los Angeles Basin was curtailed because of lack of pipe-line outlets. This work was handled by a small committee of executives and engineers of some of the pipeline companies without any established. Method such as obtains at present. Not all of the major companies participated in ibis curtailment and the effort was not well organized. The problem then was principally to move the oil. The crisis passed in September of 1923 from then on the major companies each on it own initiative, shut in additional production. At Domiuguez, in 1921, Shell, Union and Associated agreed to limit drilling to a 100-ft. zone for one Near. In the summer of 1925, operators at Ingde-wood agreed to limit developments to a 1300-ft. zone during the 1925 drilling campaign. In the summer of 1927, the Ventura operators cut back their production one-third and deft it thus for 90 day. Drilling in this field has always been at a slow and conservative rate.

Jan 1, 1932

By Robert Rhea Goodrich

This research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward I?. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. Petrogeaphic DescRiption Texture: variable. Fine to medium mixed aggregate. Original Structure: Obscurc. Secondary structure: Fractured; healed. Mineralogy (Minerds are grouped for interpretation purposes and are arranged, in each group in approximate order of abundance)

Jan 1, 1916

By Bernard MacDonald

Of the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the cluantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted, the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide,plant than that of being economical and corlvellient containers or receptacles for holding the pulp, solutiou, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to dolids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge; that is, each solid particle of the pulp, whether it be of' 180- or 400-mesh size, should be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertaiued to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Jan 1, 1912

By G. J. Ballmer

Drilling and blasting 12-in. blastholes started about the middle of 1946 and has worked out so well that about one half of the blasting, formerly done with 9-in. holes, is now done with 12-in. holes. In most of this work the harder benches were chosen for the 12-in. size because these were the areas where the greatest difficulty was encountered in thorough fragmentation. At the start of this experimental work a 42-T Bucyrus- Erie churn drill was available whereas all other blasthole drilling was being done with 29-T rigs. The large drill was first equipped with a standard 9-in. string of tools but it could not drill quite as fast as the 29-T drills. How- ever, when the weight of the string was increased about 700 lb, or to a total weight of about 3500 lb, it was found that the 42-T exceeded the drilling speed of the 29-T by about 25 per cent. When a 12-in. bit was substituted for the 9-in. bit the 42-T rig again dropped behind the drill- ing rate of the 29-T rigs. At this stage of the experiment the 42-T was using a 12-in. bit with detachable points and the total weight of the string of tools was about 3800 lb. It took longer to change the drill points than it did the regulation bit and this accounted for some of the slower drilling rate. When a heavier stem and standard construction 12-in. bits were used it was found that the 42-T could drill a 12-in. hole slightly faster than a 29-T could drill a 9-in. hole even in the hardest rock in the pit.

Jan 1, 1949

By Clyde Williams

A MAN who is a first-class metallurgist, engineer, and scientist and an outstanding organizer, administrator, and executive and who, at the same time, has an innate ability to "make friends and influence people" everywhere he goes is an exceptional personality at any time. And if such an individual can retain this combination of virtues during a great war despite the fact that the Government loaded him with enough work and responsibility for three such men. he is a most exceptional personality. And if he can keep his head and maintain an unfailing sense of humor during the trying war years and, while dealing with hundreds of jittery metallurgists and metalworkers, with Army and Navy brass, and with red-tape-entangled war agencies by the dozen, he is a rare personality indeed. Such a man is Clyde Williams, director of Battelle Memorial Institute. who will be President of AIME in 1947. The Institute is fortunate in having him as its mentor during what may be a critical and important year.

Jan 1, 1947

By C. E. LAWAL

WITH the object of adapting high-school vocational courses to the industrial needs of the community, a few high-school officials in West -Virginia working with the School of Mines of the State university decided to try an innovation this year. The purpose of this experiment was to teach coal mining in two high schools situated in mining communities. We thought that if a course in coal mining would be included in the list of optional courses offered in the high school, it might interest some of the boys, and if the course were properly taught it would undoubtedly be of inestimable value to those boys who later decided to take up mining work as their vocation. This coal-mining course was started last September in the Berwind and Gary high schools in West Virginia. The high-school officials in their conferences with' us decided that we should work up the outline of this course and they would assign the science teachers of the schools as instructors, with ,the understanding that we would help 'these instructors with this work. We consented to all this and submitted -an outline to the school officials which they are following this year.

Jan 1, 1929

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.'-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By Valentine R. Garflas

The Mexican oil fields, during 1921, produced in round numbers 203,000,000 bbl. of which 176,000,000 bbl., or 86 per cent., were exported, the bulk of these exports, or about 73.3 per cent., going to the United States. The Mexican exports were divided by grades as follows: Light crude, 47.0 per cent.; heavy crude, 22.0 per cent.; tops, 3.5 per cent.; fuel oil from light crude, 24.0 per cent. The balance, or 31/2 per cent., includes the bunker fuel shipments and the coastwise trade in Mexico, which is not classified as to grades. The figures show that, in importance, the light-oil fields form about 75 per cent. of the Mcxican petroleum industry. The production of the Panuco field has followed the general history of the American fields, and its gradual decline, which is at present foreshadowed, may be estimated as well as its ultimate economic life. On the other hand, the behavior of the light-oil fields to the south is unlike any in the world so far discovered, and as a result we have concentrated overproductions followed by sudden droughts, both sometimes equally unexpected. The coming in of two or three gushers within adequate pipe-line facilities will flood the market with 100,000 bbl. or more a day, while the flooding by water of a particular pool will, in a few weeks, remove from the market one-half the total production of the Mexican fields.

Jan 1, 1923

By C. W. Hall

Owin to its isolation and comparatively small tonnage, the Yoquivo district is not widely known; though financially important andgeologically, quite interesting. San Francisco de Yoquivo, the center of the mining district, is in the western part of the state of Chihuahua, Mexico; about 35 miles west of San Juanito, on the Kansas City, Mexico & Orient R. R. The town can be reached from the railroad by a good trail over a rugged country. The elevation of Yoquivo is 6500 ft., and peaks surrounding the town are 2000 ft. higher. The mining towns of Concheño and Ocampo are 25 miles northwest, and Uruachic is 20 miles southwest. The climate, temperate and healthful, is almost ideal. The rainy season begins in July and ends the latter part of September. There is usually, though not always, some precipitation in all months except April, May, and June. The mountains are covered with pine and scrub oak. Water, wood and lumber are plentiful for all ordinary purposes, and hydroelectric power is available for about six months of the year, when wood for steam power is utilized as an expedient. The district has been worked recurrently for over 60 years. The Yoquivo province lies on the steep western slope of the Tara-humara division of the Sierra Madre range of mountains. The province is traversed by many deep canyons, most of which flow west. The town is situated on the San Francisco arroyo, which makes a confluence with the Huevachic stream 236 m. southwest; the Huevachic in turn joins the Candemeña river farther down and these two drain the western flank of the Tarahumara mountains and form the headwaters of the Mayo river. The claims of the Yocluivo Development Co., which is the only organization in the district with a record of any considerable production, lie within an area roughly l½ m. square. Thc area extends from the San Francisco arroyo north, and from the Dolores arroyo west, and is confined to the andesite formation. General Geology The terrane about Yoquivo is composed of a series of Tertiary eruptives that consist of numerous phases of andesite and rhyolite, and

Jan 1, 1927

By J. D. Cannon

SLAGS studied in this investigation were from 0.25 to 0.35 pct plain carbon steels and were melted in a 3-ton acid-lined Lectromelt furnace with a 2500-kva transformer. The melting process employs a short, violent boil, which is partially blocked, and the desired carbon content is adjusted by pig iron or iron ore, depending on the preliminary carbon. A relatively small volume of slag is used in refinement. Bottom is here defined as that portion of the furnace that comes in contact with the molten metal, or all the surface below the slag line. Bottom trouble-i.e., holes in the bottom lining-is very seldom experienced at our plant. We have been watching the bottom lining over a period of some boo heats in the hope of having holes large enough to supply data for this report, but none occurred during that period. The bottom is eroded uniformly, occasionally with slightly deeper depressions around the taphole.

Jan 1, 1947

By J. Szekely, P. Tarassoff, N. J. Themelis

In a copper converter air enters the bath in the form of turbulent jets. The interaction of these jets with the molten matte is fundamental to the converting process. In the present study, an equation is derived to describe the trajectory of a gas jet in a liquid. Calculated and experimental results for air jets injected into water are in good agreement. The trajectories of air jets in copper matte are predicted. THE air injected through the tuyeres of a Peirce-Smith copper converter emerges into the bath of molten matte in the form of a highly turbulent jet. The air jets affect a number of chemical and physical processes occurring in the converter: i) Converting Rate. It is generally recognized that the production capacity of a converter is limited by the flow of air which can be injected through the tuyeres and by the oxygen efficiency. In turn, the air flow is limited by pressure drop considerations or by the amount of splashing within the converter. ii) Oxygen Efficiency. This depends on the dispersion of the air jet in the liquid bath, and its trajectory through the bath. iii) Mixing. The jets act as mixing devices by transferring momentum energy to the bath; in this way the heat generated by the converting reactions occurring in the jets is distributed through the bath. iv) Refractory Wear. The proximity of the jets, which are centers of heat generation, to the refractories in the tuyere zone may have an important effect on refractory life. Mixing conditions in the bath will also influence refractory erosion. v) Splashing, and Accretion Build-Up. The energy of the jets is not dissipated entirely in mixing the bath. particles of liquid are carried out kith the gas above the surface of the bath in the form of liquid spouts and droplets. These result in the undesirable build-up of accretions on the converter mouth, and dust losses in the flue gas. Despite the importance of the interaction of the air jets and the matte in a converter, very few studies of the fluid dynamics of converting have been reported in the literature. Metallurgists in the USSR appear to have been more concerned with the subject than their Western counterparts. Deev et al.1 studied the interaction of an air jet with aqueous solutions in a converter model and qualitatively determined the tuyere air velocity and tuyere inclination which produced the most favorable results with respect to good mixing in the bath, and minimum splashing. Shalygin and Meyer-ovich2 also examined the air-matte physical interaction both in models and in industrial converters; they concluded that in conventional converting practice, there was no significant penetration of the air jets into the matte layer, and consequently the converting reactions occurred mainly in a zone adjacent to the tuyeres. The behavior of air jets in a converter bath, and the aerodynamic characteristics of tuyeres are discussed at length in a monograph on converting by Shalygin.3 However, the description of the phenomena occurring in the converter bath is largely qualitative. The side-blown Bessemer converter for steelmak-ing is very similar to the Peirce-Smith copper converter. Among the few investigations of the behavior of air jets in the bath of a Bessemer converter are those of Kootz and Gille4 who studied splashing in the course of an investigation on the effect of blowing conditions and converter shape on nitrogen pick-up in Bessemer steel. They found that during blowing standing waves were formed on the surface of the bath; the amplitude of the waves increased with the depth and angle of tuyere immersion until the whole bath moved backwards and forwards causing heavy splashing. Kazanstev5 used a model of a Bessemer converter to obtain correlations between the axial velocity of a gas jet and distance from the tuyere orifice and the Froude number of the jet. shalygin3 used these results to calculate the horizontal penetration of an air jet in a copper converter; the penetration was defined as the distance in which the axial jet velocity decreased to 10 pct of its initial value. However, the rising trajectory of the jet was not taken into account. In the absence of quantitative information on the fluid dynamics of converting, the design of copper converters has been based mainly on operating experience. Such experience tends to vary widely from smelter to smelter., This is reflected in Table I which is based on data compiled by Lathe and Hodnett.6 Aside from a rough, and perhaps obvious correlation between the total air flow and converter volume, Fig. 1, no pattern emerges from the data. For example, tuyere throat air velocities vary from 215 to 465 ft per sec in converters of the same size, for little apparent reason. The air jet energy input per cubic foot of converter volume, which may be taken as a measure of the amount of mixing in the converter bath, also varies greatly. A recent analysis of converter data by Milliken and Hofinger7 has also revealed unexplained variations in operating parameters. It is believed that by gaining a better understanding of the fluid dynamics of converting a more rational basis may be provided for the design of converters. In particular, it is proposed that if one takes into account the desirable criteria of a high converting rate, high oxygen efficiency and long refractory life, there should be an optimum configuration of tuyere air flow for a converter of a given diameter. The present investigation is concerned with the form and trajectory of an air jet in a converter bath. The general theory of turbulent jets has been expounded by Schlichting8 and Abramovich.9 However, most experi-

Jan 1, 1970

By Benny Langston, Frank M. Stephens

Although little information is available concerning small-scale equipment for dust collection in laboratories, it is possible to adapt standard equipment for laboratory use. Dust from laboratory processes may be collected by cyclone separators, filters, electrostatic separators, scrubbers, and settling chambers. IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. considerable data has been accumulated on both operation and design of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process. For most applications standard dust-collection equipment is too large for use in the laboratory; however, for control of dust in large working areas it is often possible to use a standard dust collector, such as an air filter, with branch ducts to eliminate a health hazard. For example, the well-furnished sample-preparation room containing small jaw crushers, rolls, and pulverizers, in addition to the riffles and screens necessary for preparation of samples, presents a perennial source of dust. The authors' experience has shown that a combination system consisting of overhead branch ducts to the individual equipment and floor ducts with grills, where applicable, connected to a central dust collector effectively removes dust generated in preparation of samples. Fig. 1 is a sketch of a downdraft dust-collector for table installation. Similar systems can be built with floor grids. For portable equipment such as laboratory vibrating screens this type of installation with a steel grill to support the heavy load is reasonably efficient. Overhead branch ducts to individual crushing and grinding equipment, although efficient, must be carefully controlled by dampers to prevent excess loss or a change in the composition of the sample. Change in sample composition can result from excess velocity, which causes selective removal of constituents of low specific gravity. Fig. 2' shows the theoretical effect of terminal velocity on spherical particles of different specific gravities in air and water under action of gravity. Fig. 3 shows the effect of air velocity on composition of CaCO, coal mixtures. Although the entrainment of dust particles in a moving air stream is the basic mechanism by which all dust-collection equipment functions, usually intake velocity of the dust-collection system must be controlled to prevent loss of part of the sample. As an example of what may happen when excess velocities are used, a mixture of 50 pct coal and 50 pct limestone was crushed to —10 mesh and fed to a pulverizer equipped with an overhead dust-collection system. Fig. 4 shows the overhead dust-collection equipment used in this test. The pulverizer was set to give a product 95 pct —100 mesh in two stages. Velocity of air passing over the lip of the pulverizer was measured with an anemometer. After grinding, the finished product was analyzed to show the amount of calcium carbonate present. Fig. 3 shows graphically the increase in calcium carbonate as velocity through the dust-collection duct was increased. These data show that at a velocity of 1 ft per sec little if any of the coal was entrained by the overhead draft. At the maximum velocity, about 6.5 ft per sec, approximately 7 pct more coal was entrained than calcium carbonate. From an operating standpoint, this problem can be remedied easily by dampering the line to control velocity. The lowest velocity commensurate with satisfactory dust control should be used to prevent excess loss and, in some cases, selective dust loss. Collection of Dust in Laboratory Processes As in industry, the engineer desires to collect efficiently the dust produced by processes being investigated on a laboratory scale. However, in the collection of laboratory dusts he is faced with two additional problems: 1—The volumes of gas and the quantity of dust that must be recovered are small when compared with the capacity of standard dust-collector equipment, which must be scaled down in design except for collection of dust from large pilot-plant operations. 2—In addition, because of the variety of problems studied in the process laboratory, the engineer cannot design today a dust collector that will meet the conditions imposed by the processes of tomorrow. Sometimes, therefore, he must compromise collection efficiency to minimize the cost of fabrication and the amount of time diverted from the metallurgical to the dust-control problem. For collection of dust from laboratory processes a cyclone separator, filters, electrostatic separators, scrubbers, and settling chambers can usually be adapted for small-scale operations. The following

Jan 1, 1955

By G. H. Kennedy, H. E. Criner

CYCLONE thickeners are "hydraulic centrifuges" designed either to produce a maximum practical separation between the water and solids of a feed slurry or to classify the slurry solids according to particle settling rate. The possibilities of utilizing the thickener to "close" plant water circuits have been investigated. Since the thickener becomes an integral part of the plant water circuit when installed, the basic means by which the solids content of all circulating water systems must be controlled is reviewed. All coal not separated from the circulating water by means of dewatering screens or settling devices must be bled from the plant at the same rate as they are being fed or created by degradation. If this were not true, the circulated volume would finally be completely filled with solids. If the rate of bleed is low, the solids concentration in the bleed and circulating water generally will be high. To keep a reasonable circulating water concentration, large amounts of fresh water must be supplied and the bleed rate must be high. These conditions are usually undesirable because of the difficulty in securing fresh water, the loss of large quantities of coal, and the pollution of nearby streams. Thickeners are the primary stage in the separation of the water contained in the bleed from the coal. Since a thickener, when operating with reasonable efficiency, usually cannot be expected to deliver an underflow containing less than 50 pct water, secondary dewatering devices such as a slurry screen or vacuum filter must be used to separate additional water from the bleed. The surface area required by the filter or screen will be nearly proportional to the total water which must be handled, and therefore the thickener becomes necessary to hold down the original cost. The water separated from the coal is then returned to the plant circuit to maintain the water balance and thus becomes the source of fresh water. It is not necessary to return clear water to the plant to maintain control of the circulating water concentration. It is only necessary that the bleed dewatering devices remove coal in all sizes at a rate equal to that at which these sizes are entering the circulating water. However, practically speaking, in order to maintain low solids concentration, it is usually necessary that the thickener have good recovery characteristics on bituminous coals in those sizes down to 400-mesh. The thickener can remove the smaller sizes from the closed-circuit system at the "solids in" rate and prevent their "build up" in the circulating water as shown in Fig. 1. With the portion of the feed water going directly to the underflow, comes the very fine solids not concentrated by the cyclone. All the larger solids are removed from the feed and delivered in a concentrated condition at the underflow. To apply thickeners with some reasonable assurance that operating requirements will be met, it is necessary to know the rate at which solids of all sizes must be removed from the circulating water and to know the thickener characteristics. The required removal rate of fine solids not recovered by other dewatering devices may be estimated from the size distribution and tonnage of the plant feed with a reasonable allowance for degradation in the circulating water system. A more reliable estimate may be secured by sampling the plant bleed water during a constant load period.

Jan 1, 1952

By Augustus Locke

Two Opposed Interpretations of the Tonopuh Structure.—The important geological publications concerning the Tonopah min-ing-district are those of Spurrl aud of Burgess.² In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Brieflyj Burgees regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesitc, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.—The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of

Jan 1, 1913

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly i00 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi¬tion is accompanied by a change in volume of as much as S per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potters have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to g0 per cent Mn. is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to ½ in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By P. D. Wilson

The Province of British Columbia covers 382,000 sq. mi., about 250,000 sq. mi. of which have not been prospected. In fact, the coast country and the islands are so heavily timbered and the surface covered with so thick a mantle of soil, muskeg, and, over broad areas, glacial drift, that prospecting and even trail breaking are extremely difficult. It is only along the coast or stream channels, or above the timber line, or where snow or rock slides have scoured the surface, that rock outcrops can be found. Glaciers nestle in many of the cirques and fill the valleys in the higher ranges. Great ice sheets and perpetual snow persist in certain localities, thus reducing the exposed areas worth prospecting. Almost the entire country has been subjected to intense glaciation, so that the conspicuous oxidized outcrops of orebodies typical of the southwestern United States and Mexico do not exist and surface bodies of enriched or oxidized ore are rare. With few exceptions, the mines1 of the Province are working primary ore. Development, have proved that some of these orebodies are large and important, although usually comparatively low in grade. Besides the few mines that have produced most of the minerals, there are many small mines, but their total output is unimportant. Considering the number of mines and prospects and the widespread mincralization, it is strange that no really great mines, comparable in sizc and richness with those in the western United States, have been found. The deposits that most closely approach the status of great mines are

Jan 1, 1923

By P. D. Wilson

The Province of British Columbia covers 382,000 sq. mi., about 250,000 sq. mi. of which have not been prospected. In fact, the coast country and the islands are so heavily timbered and the surface covered with so thick a mantle of soil, muskeg, and, over broad areas, glacial drift, that prospecting and even trail breaking are extremely difficult. It is only along the coast or stream channels, or above the timber line, or where snow or rock slides have scoured the surface, that rock outcrops can be found. Glaciers nestle in many of the cirques and fill the valleys in the higher ranges. Great ice sheets and perpetual snow persist in certain localities, thus reducing the exposed areas worth prospecting. Almost the entire country has been subjected to intense glaciation, so that the conspicuous oxidized outcrops of orebodies typical of the southwestern United States and Mexico do not exist and surface bodies of enriched or oxidized ore are rare. With few exceptions, the mines1 of the Province are working primary ore. Development, have proved that some of these orebodies are large and important, although usually comparatively low in grade. Besides the few mines that have produced most of the minerals, there are many small mines, but their total output is unimportant. Considering the number of mines and prospects and the widespread mincralization, it is strange that no really great mines, comparable in sizc and richness with those in the western United States, have been found. The deposits that most closely approach the status of great mines are

Jan 1, 1923