Search Documents

By William Best

OIL burners, oil furnaces, and methods of installation, have been the subject of many articles, but information concerning oil-burning systems, based upon scientific principles, is still in great demand, especially in the manufacturing districts of our country. Fuel oil, as it is termed (this being the residuum from oil refineries), has for many years been of great service to our manufacturers, and has justified its popularity not only by producing a superior manufactured product, but by turning out approximately 50 per cent. more product than can be made with coal fuel under like conditions. To install a system requiring only an oil-storage tank, a small pump, and an oil-supply main with numerous laterals leading to the various burners, furnaces, boilers, etc., is a comparatively simple matter; and, because fuel oil is very volatile, it is not necessary to heat it, even during the winter months in a very cold climate. Furthermore, only a small amount of power is required to atomize fuel oil, this often being done by a positive pressure blower, or by a mechanical burner. An analysis of fuel oil, together with that of various other liquid fuels, is given in Table I.

Jan 2, 1914

By Lester F. Engle

Books have been written, complex charts drawn, great batches of punched cards handled by ever increasing numbers of computers, and innumerable meetings held-all for the purpose of making effective the ultimate objective of new, revised or improved process facilities. It is to the credit of management, engineers, and others that in the vast majority of cases, the outcome of their work has been technically sound and economically rewarding. There is a way, however, to insure even better results.

Jan 5, 1966

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By Sir Robert Hadfield

LAST year this Institute was good enough to accept some remarks by the writer regarding sound steel, entitled Plant for Hadfield Method of Producing Sound Steel Ingots, being a continuation of a research in which for some time the writer has been engaged, and full particulars of which were submitted in papers entitled A New Method of Revealing Segregation in Steel Ingots, and Method of Producing Sound Ingots, read before the Iron and Steel Institute in October, 1912. These papers gave rise to a very interesting discussion, both in England and America. This question is one of vital importance, as unless sound steel in the form of ingots is first obtained, sound steel in the finished forms of rail billets, rails, bars, sheets, and other forms cannot be expected. The working stresses demanded by modern conditions are so great, each year they probably approach nearer to the limit of safety, that without doubt those who produce steel will be compelled to pay the attention which this subject deserves. Moreover, the problem is not an insuperable one, as shown by the writer in the papers above referred to. In view of the information which has already been presented in these papers, it is not now necessary to go into details of the system advocated by the writer, except to repeat that the ingots and steel now referred to were produced by employing in the first place sound fluid steel, free from blowholes, this being poured into ordinary ingot molds, provided with the necessary feeding heads, the insulating slag medium, also charcoal and air blast or other suitable form of applying heat to the head portion of the ingot. Tile upper or head portion of the ingot is kept fluid by the intense heat generated by the air blast and charcoal, so that such fluid steel passes into the body of the ingot below the head, thus feeding and avoiding the shrinkage or piping which would otherwise occur. The result is the production of a sound steel ingot, free from blowholes, segregation and piping, and in which the waste portion, usually termed the discard, is but little over 7 or 8 per cent.

Jan 4, 1914

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By EVERETTE DE GOLYER

USE of geophysical methods in the search for new pools and as an aid in the development of known pools and prospects reached a new all-time peak for the oil industry in 1933. The outlook for 1934 is for work to continue at an even greater rate. The area of greatest activity, as in previous years, was in the Gulf coastal plain of Texas and Louisiana, particularly through a belt of territory some 20 to 30 miles wide parallel to the coast line and some 80 miles inland from it-the so-called "Jackson play" or "Conroe trend." This area was surveyed in an attempt to find additional pools of a type similar to Conroe, a pool not discovered directly as a result of geophysical surveys but one which was indicated by refraction surveys before it was drilled and one which was accurately outlined as to structure by reflection surveys shortly after the completion of the first few wells. Surveys were made over this belt, extending from Texas, across Louisiana and into Mississippi and Alabama, chiefly by the reflection method and torsion balance, and to some extent by pendulum and magnetic methods.

Jan 1, 1934

By William Priestley

IN THE manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and elastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungsten, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured-by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. DESIGN OF GUN FORGINGS In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun are made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The elastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge.

Jan 12, 1921

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By E. C. Houston

The phosphate ores mined in middle Tennessee typically consist of granular rock phosphate particles disseminated in a clayey matrix. In the TVA plant near Columbia, Tenn., the phosphate ore is mined, made into a slurry with the addition of a small amount of sodium hydroxide as dispersant, and treated in a hydroseparator to remove minus 10 micron material. The hydro-separator underflow, comprising a rough concentrate, is transported by pipeline to the plant; the hydro-separator overflow, comprising a tailing, is flocculated by addition of calcium sulphate and is discharged to settling ponds at a rate of about 1400 gpm. Sedimentation in the ponds produces a clarified effluent, which may be recycled for use as process water or discharged to surface drainage. This method of tailing treatment is not entirely satisfactory since poor sedimentation characteristics of the tailing result in poor ultimate utilization of pond storage volume.

Jan 1, 1949

By William B. Plank

IN my studies during the past twenty years of the enrollments in the mining and metallurgical schools of the United States and Canada, I have been struck with the great diversity in the curricula offered by these schools. In 1933 when I made my first complete study of the schools (Mining and Metallurgy, May 1934, p. 211), I discovered 19 different curricula or programs of study, leading to almost as many different bachelor degrees, in the 49 schools in the United States and the 4 schools in Canada. These were: (1) Mining Engineering, (2) Coal Mining, (3) Metal Mining, (4) General Mining, (5) Mining Administration, (6) Mining and Metallurgy, (7) Metallurgical Engineering, (8) Metallurgy, (9) Petroleum Engineering, (10) Petroleum Refining, (11) Petroleum Geology, (12) Petroleum and Natural Gas, (13) Ceramic Engineering, (14) Ceramics, (15) Geological Engineering, (16) Mining Geology, (17) Economic Geology, (18) Geo- physics, (19) Fuel Technology.

Jan 3, 1950

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By Robert L. Bates

On April 2 and 3, 1970, more than 100 geologists attended the Sixth Annual Forum on Geology of Industrial Minerals at Ann Arbor, Mich. After this brief appearance, the Forum apparently ceased to exist- but it didn't really, and another spring will see it again in action, in another corner of the country. The organization might be characterized as the country's largest permanent floating conference on the geology of industrial minerals. What is the Forum, where did it come from, and what is it up to? The idea originated in 1964 with a small group in the Department of Geology at Ohio State University, Columbus. This group felt that a forum was needed for the exchange of geologic information on industrial rocks and minerals. They envisioned an approach-which has subsequently been adhered to--that would be dominated neither by geological academics interested in theoretical problems nor by practical engineers concerned with processing large tonnages of rock. It was proposed to focus attention on the middle part of the spectrum, especially on practical problems of geological occurrence and how these problems affect extraction and use. In terms of the standard rock-products flow sheet, which starts with a truck unloading into the primary crusher beneath the words 'from quarry,' it was proposed to focus geological attention on what is beyond the primary crusher, out in the quarry.

Jan 1, 1970

By Paul Billingsley, Augustus Locke

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d'Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By Augustus Locke, Paul Billingsley

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d'Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana's gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By M. J. Saarivirta

A high-purity copper-zirconium alloy system was imesti-gated. The zirconium content of the alloys studied varied from 0.003 to 0.23 pet. The solid solubility of zirconium in copper and some physical and mechanical properties of the alloys have been determined. By proper heat treatment, Cu-Zr alloy can develop a high electrical conductivity and resistance to softening at temperatures up to 500°C (930°F). This combination of desirable properties makes this alloy superior, to other com-merzcrrl copper base alloys for- use in the electrical conductor field. DEMAND for high conductivity copper alloys that retain their mechanical properties at elevated temperatures is growing rapidly. At present, copper-base alloys such as copper-silver and copper-chromium are used where these characteristics are required. As an example, commutators in electric motors are often made of these alloys. However, the life at elevated temperature of commutators made of copper-silver alloys is much shorter than the life of the same part made of copper-chromium and copper-zirconium alloys. Copper-silver alloys are subject to creep and subsequent failure when the service temperature exceeds several hundred degrees centigrade. Use of copper-chromium alloys has been known for the past several years, but little information is available in the literature concerning the properties of alloys in the copper-zirconium alloy system. Some work had been directed toward determining the solubility of zirconium in copper as well as determining properties of the Cu-Zr alloys. These investigations have revealed the superior high-temperature and electrical conductivity properties of copper-zirconium alloys over copper-chromium alloys. The United States Metals Refining Co., Carteret, N. J. has recently produced OFHC R copper-zirconium alloys for experimentation and evaluation. Because OFHC R copper contains no appreciable oxygen, no harmful oxides are formed and the full benefit of Zr as an alloying addition is obtained. This paper describes the results of this work. It contains room-temperature and some high-temperature data which have been obtained after various processing techniaues. Actual elevated temperature properties are being determined and will be reported in a separate paper. Preliminary results obtained at elevated temperatures suggest that the Cu-Zr alloy is superior to other high conductivity copper-base alloys. WORK PROCEDURE The high-purity oxygen free (OFHC R) copper-zirconium alloys with zirconium content ranging from 0.003 to 0.23 pct were cast into 4-by 4-in. wirebars by both continuous casting and conventional casting methods. Zr was added in the form of a master alloy containing 30 pct Zr and 70 pct Cu. Castings were analyzed for zirconium and nine bars containing various amounts of zirconium were selected for this study. The results of analyses and the sample numbers are given in Table I. Typical analyses of OFHC R copper are also shown. The following properties were studied: A) Solid solubility of zirconium in copper. B) Effect of zirconium on properties of copper. C) Effect of combined working and heat treating on properties of Cu-Zr alloys. The solid solubility of zirconium in copper was determined by metallographic techniques. Specimens for this phase of the investigation were hot rolled at 900oC (1650oF) to 0.250-in. rod. The rolled rods were cut into 2/3-in. long specimens and solution annealed at 950 °C (1740°F), 980°C (1795 °F). and 1020 °C (1870 °F) for 6 hr and quenched in water. In order to find the solid solubility limits at lower temperatures, the homogenized specimens were reheated at various temperatures for 1 hr and quenched. The physical and mechanical properties were determined on 0.250 in. rod, 0.132- and 0.081-in. wires. The wires were cold drawn from the 0.250-in. rods after they were solution annealed at 980 °C (1795°F) and quenched in cold water. Mechanical and electrical properties were determined on cold drawn and

Jan 1, 1961

By E. C. Wright

THIS paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with "or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxida-tion resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium.

Jan 1, 1933

By John F. Elliott, John P. Hager

The standard free energies of formation of the lowest stable sulfides of chromium, molybdenum, and tungsten in equilibrium with the corresponding metal hazle been determined by reacting the sulfide and metal with H2(g)/H2S(g) mixtures. The reaction is A method for estimating the standard ~nolav entropies and standard entropies of formation at 298°K of the sul-fides of refractory metals is presented. The standard free energies of formation of the lowest sulfides of the metals in group VIa of the periodic table are probably best determined with the reaction* is known with greater accuracy than is that property for any other sulfur-bearing compound or solution which might serve as a reference phase to establish the chemical potential of sulfur for the essential re- However, there still remain significant problems to the use of Reaction [I] in studying these sulfides. First, the equilibrium gas ratios (Ph2S/PH2) are very small, and with the most stable sulfides in the series the ratios tend to be at the limit of the range for precise chemical analysis (10-4); and second, the reaction rate for the formation or reduction of these sulfides appears to be relatively slow. A primary reason for the latter problem is that the gas phase near the equilibrium concentration has very little capacity for transport of sulfur. It is to be noted that the thermo-dynamic properties obtained from the experimental results by Eq. [I] apply for 1 g-atom of sulfur in the metal-saturated compound even though the exact composition of the compound has not been determined. The work reported here is a study of the standard free energies of formation of the lowest sulfides of chromium, molybdenum, and tungsten, and of copper, by Reaction [I]. In planning the experimental program, it was decided that the technique that has been used previously3"' could be used with modification and that an improved analytical method was needed for determining H2S in the gas phase. THE EXPERIMENT The once-through flow of gas was selected in preference to recirculating the gas, a) because of the low sulfur capacity of the gas, b) because of the relatively slow rate of reaction and the danger of the

Jan 1, 1968

By T. L. Joseph

A study is made of the amount of solution loss necessary to maintain the reducing power of the gas stream in the blast furnace. Curves are presented to show the effect of solution loss, moisture in the blast, and carbon dioxide from the flux on the nitrogen in the THE blast furnace process is based upon the counter flow of gases and solids. As CO, N, and H, flow upward from the combustion zones, oxygen is acquired from the descending charge. In the reduction of iron ore, a portion of CO is converted to CO, and similarly a portion of H, is converted to water vapor. The inert N,, from the air used in combustion, passes through the furnace with little change. Its concentration is, however, decreased by reactions such as direct reduction and solution loss which increase the volume of CO in the gas stream; Similarly the evolution of C02 from the limestone also dilutes the nitrogen. he purpose of this paper is to illustrate an idealized and simplified method of studying furnace processes by following changes in the gas phase between the tuyeres and the stock line. A more specific objective is to evaluate the effect of solution loss upon the CO/CO, ratio in that region of the furnace in which FeO is reduced to metallic iron. This last stage of reduction requires relatively high CO/CO, ratios to exceed the equilibrium requirements. Solution loss or the reaction of COZ with C to produce CO has a pronounced effect upon the ratio of the carbon gases and is necessary to maintain the reducing power of the gas stream if the consumption of coke is low. It will be explained later that indirect reduction followed by solution loss is stoichiometri-cally equivalent to direct reduction. Calculations will be made to show how the composition of the gas in the region of the mantle varies with coke consumption and with different amounts of solution loss. Such calculations show the condi- tions under which gasification of C with oxygen in the charge is needed to maintain the reducing power of the gas. Equilibrium conditions for FeO and the carbon gases will be used to establish a minimum CO/CO, ratio below which reduction will not proceed. The manner in which carbon is gasified in the furnace, at the tuyeres with oxygen in the air or above the tuyeres with oxygen from the charge, will be a basic feature of all calculations. It is hoped that greater interest in the use of top gas as a means of following furnace reactions will be aroused by the calculations and generalized curves which are presented. Bosh Gas Equations Subject to some alteration by the amount of moisture in the blast and by direct reduction, the gas leaving the combustion zones of a blast furnace has a definite composition. Because a relatively small amount of oxygen is acquired from the charge in the bosh and in the crucible, the products of combustion undergo little change until they enter the shaft. Bosh gas is, therefore, essentially the products of combustion of carbon in a deep fuel bed with air. The relative weights and volumes of reacting materials are expressed by the equation: 2~ + 0? + 3.76N, = 2C0 $ 3.76NZ [I] Air Bosh Gas -air = 79% N? = 3.76) 21% 02 Starting with a known mass of C consumed largely by air, Eq 1, but partly by water vapor, Eq 2, the volume and C + H2O = CO $ H? [21 composition of the bosh gas can be calculated and subsequent changes followed as reactions take place at various elevations in the furnace. As shown in

Jan 1, 1952