Search Documents

By J. J. Taber

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By John Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require addi-tional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894° to 898° C. The dissociation of dolomite and magnesite, although studied by several investigators, 4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

By Theodore B. Comstock

The existing topographical features of the United States present many points of interest to the student of dynamical geology, but there is, perhaps, no subject which offers a more promising field for investigation than the relations between the geological structure and the mineralogical characteristics of the principal mining districts. There are seven prominent culminating points in the relief of North America, each one of which can be used as a type of the physical features of all the others. Again, if we divide these seven elevated districts into two sets, we shall discover a still more striking parallelism between the individual members of each group. But the most remarkable revelation is the fact that each one of these points is more or less closely the centre of an area of economically important mineral resources. It is interesting to note in this connection that six of these mineral tracts lie mainly within the borders of the United States, three of them being almost wholly in our territory. For

Jan 1, 1883

By Howard N. Eavenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few ears after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained. but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested. but without any illusions that it will be followed or that much attention will be paid to it.

Jan 1, 1946

By Thomas H. Leggett

The conditions surrounding this mine are, perhaps, not sufficiently rare or significant to warrant special attention. A certain interest, however, attaches to the locality through the recent discovery of fossil cycads made there by Mr. Charles M. Rolker, of New York, who has repeatedly visited this district, fixing the geological horizon

Jan 1, 1889

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By E. W. Pehrson, J. W. Furness

THE five charts presented here- with are part of an original group prepared by the U. S. Bureau of Mines showing the international trade in the principal metals and metallic ores. Charts 011 anti- mony, chromite, copper, lead, manganese, mercury, nickel, tin, tungsten, and zinc were published in the February, 1936, issue of the Engineering and Mining Journal. Those shown here include bauxite, aluminum, iron ore, pig iron, and the platinum-group metals.

Jan 1, 1936

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

By Patrick H. O’Neill

FUNDAMENTALLY a dredge designed for operating under arctic conditions and particularly when the temperature is below freezing is not greatly different than one for use in more moderate climates. Because of the accumulation of ice it is necessary to design suspension units to carry an increased weight when ice forms on the digging ladder or stacker. Winch room and house must be made with double walls and insulated. The dredge must be heated either by steam or by circulating warm air electrically heated. The stacker must be covered and heated to avoid having the drive units frozen tight. Actually the worst trouble that might develop in a stacker, because of cold weather, is the freezing of spilled material and ice accumulation on the head pulley and the underside of the belt. For this reason, stackers are completely enclosed and the pan kept open to get rid of any spilled material and to prevent overloading. Since the stacker is the most vulnerable place on a dredge in cold weather, heat is turned on there long before it is necessary any other place on the dredge. The principal points of interest in' connection with dredging, under subfreezing conditions, concern the preparation of the ground being dredged and the frozen ponds. In the interior of Alaska, and also in the Yukon territory of Canada, most of the gold bearing gravel deposits are permanently frozen and they are also covered by variable thicknesses of fine grained sediment, locally called muck. The better pay areas in this frozen ground have generally been worked by the earlier miners who sank shafts to bedrock in the frozen ground, then drifted in four directions and dug out the areas between the drifts as they re- treated toward the shaft. They thawed only the area they were excavating, doing so with steam from wood-fired boilers, and hoisted pay gravel to the surface for subsequent washing.

Jan 11, 1954

By Charles L. Hosler

My function here today is not to illuminate any particular subject but simply to welcome you to Penn State and to the College of Earth and Mineral Sciences. Our college is, of course, dedicated to the same thing to which most of you have dedicated your lives--the exploration of the earth, the extraction of materials from it, and the production of useful things from those materials. We have about 2,000 students engaged in studying in preparation for service in these activities at the present time. Like other colleges of our type, we've undergone a great expansion just at a time when university budgets are contracting. This creates an interesting situation as to how we can best use our resources. This, of course, is the thing a lot of you are going to be talking about here--how we can best use the world's resources. As you well know, the expectations of the people of the world are rising, and, with the numbers of people increasing and with finite resources, there never was a time in history when it was more important that we become "quantitative" in our discovery, estimation, extraction, and utilization of those resources. I think it is admirable and very timely that you are gathered together to discuss your various approaches to this particu¬lar problem of quantifying and making most efficient use of the resources of the world. Yours is sort of a hidden profession, not just because you actually go underground, but because the public in general is not aware of where the materials they use come from. If you are successful in your professions the public will continue to be unaware. Only if you fail will your essential function become patently obvious. I wish you success both in your professional pursuits and in this particular meeting.

Jan 1, 1977

By John Birkinbine

A RETROSPECT of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are iron¬masters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried ; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

Jan 1, 1876

By John Birkinbine

A retrospect of the growth of the production of pig-iron for the past half century would be the history of the invention and introduction of heated blast as applied to the smelting of iron ores. As the apparatus employed was improved in conception and construction, the economical operation of the furnaces to which it was attached was the more marked, and the production correspondingly increased. To compare the original iron box placed over a coal fire with the modern hot-blast stove, with its combustion-chamber, gas-burners, and air-regulators, would be as unfavorable to the former as to contrast the product of the little Blauöfen with the yield of the improved furnaces of to-day. But, as these little Blauöfen were the germs from which the larger plants have grown, so from the crude apparatus invented and applied by Neilson has grown, in the face of great opposition, the more economical hot-blast stoves now in use. It is not surprising that an innovation like heated blast should have received a large amount of attention from metallurgists, nor that men of recognized ability should formerly have been found both among its champions and opponents, but it is remarkable that, at the present day, with the results of careful research and thorough experiment compiled in convenient shape for perusal, there are ironmasters who still consider it economy to allow the products of combustion to escape into the atmosphere, rather than utilize them in heating the blast, because of a supposed injury to the quality of the product. In the present state of knowledge and practice, it is proper to express as an axiom, that a well-constructed hot-blast apparatus is essential to the economic operation of an iron-producing plant. Of the interpretation of proper construction there is of necessity a variety of opinions, and, with the view of solving the problem, the apparatus for heating blast has from time to time assumed various forms. Boxes, cylinders, and pipes, placed horizontally, vertically, inclined, or in circles and spirals, have been tried; there have been pistol-shaped pipes, double pipes, divided or diaphragm pipes, siphon pipes, and as much variety in the mains, connections, flues, and setting. It is probable that, to the introduction of the bell and hopper in

By C. Gatlin, N. E. Garner, A. Podio

Experimental data from single chisel blows on Leuders limestone are presented. A pressure chamber, similar in design to well known microbit drilling chambers, was utilized to impose variorcs stress states on the sample. Confining pressure of zero to 10,000 psi and borehole pressures from zero to 5,000 psi have been used in the studies. Pore pressure was zero and the rock samples dry in all instances. Force-displacement records and visual examination of the craters indicate that the mode of failure depends on both confining and borehole pressure in certain ranges, ranging from brittle, through a transition, to near plastic. The mode of failure is reflected in the observed blow force and energy data, as well as the shape of force-penetration curves. INTRODUCTION A previous paper' presented initial data from the project on which this paper is the second report. While the first paper dealt with impact studies on synthetic rocks, the literature cited there is also pertinent to this paper, but will not be listed again in order to avoid needless repetition. This paper presents experimental data from single chisel impacts on limestone at certain simulated wellbore stress states. Specific variables investigated were combinations of borehole and confining pressure, crater geometry, a narrow range of impact velocity and the forces required to drive the chisel into the specimens under the varying conditions. EXPERIMENTAL PROCEDURE The same basic apparatus described in our earlier paper, except for the pressure vessel, was used in this study. Fig. 1 shows the complete experimental system. Fig. 2 shows details of the pressure cell, which is quite similar to the well known microbit drilling chamber. The confining (overburden) pressure system provides independent pressure control over the sample except for two, 21/4 in. diameter areas located on the sample ends. These two areas provide a pore pressure entrance on the bottom and a striking surface on the top where borehole pressure can be controlled. The ends are isolated from the confining pressure by O-ring seals. The borehole and pore pressures are related through the striking surface; they will be the same unless a seal is deposited on the borehole surface, either a mud cake or some other impermeable membrane. In these studies pore pressure control was not used, as the rocks were dry and unsaturated in all cases. Rock samples were prepared from 4-in. cubes as illustrated by Fig. 3. The circular disks of adhesive vinyl plastic protected the impact surface from the resin coating (Scotchcast No. 2) and were removed just prior to each test. This procedure insured a fresh uncontaminated surface for the impact. Fig. 4 shows the dimensions and loading of the sample, including the concentrations around the "borehole" periphery (O-ring seal). The rock used in this study was Leuders limestone, of Permian age (Leonard), quarried near Leuders, Tex. Geologically, Leuders limestone is a light gray, fossili-ferous limestone (oolitic foraminifera1 biosporite). Its fossil content is 80 to 90 per cent and consists primarily of calcitornellid, ostracods, pelecypods and oolites with the remaining part intraclasts. There are hematite or limo-nite rims on some of the intraclasts. The porosity is approximately 20 per cent, but the permeability is less than 1 md. There is no apparent orientation in the structure. Triaxial tests have been conducted to determine the variation of the physical properties of Leuders limestone in three orthogonal directions', and it is known to be unusually isotropic and uniform. Physical parameters for this rock are: uniaxial compressive strength = 9,700 psi; F = 32 and C = 2,700 psi; where + and C are Coulomb equation values (t = C+u tan +). Impact tests were run under the combinations of confining and borehole pressures shown in Table 1. Samples were dry with atmospheric pore pressure in all cases. Tests, in which elevated borehole pressures were applied, used a single layer of household Saran-Wrap to prevent horehole fluid invasion into the sample. This proved to be simple and reliable. The blunt wedge used in all the tests was 0.75 in. long and had an included angle of 60" with a 0.05-in. flat. In addition, a sharp 60" wedge was used for all confining pressures at zero borehole pressure. The chipper speed

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

A Discussion at a meeting of the New York Section, Dec. 2, 1914 D. H. BROWNE.-If 35 years ago we had met to discuss the subject that is before us to-night, the criticism that we must all be mad or we would not be here at all would have been perfectly applicable. No group of men would have come together a generation ago to discuss the subject of smelting ores without extraneous fuel, or largely by the oxidation of their own impurities, without incurring the imputation of being crazy. But metallurgy, like all other branches of human industry, progresses by idealism. In every generation there are old men who see visions and young men who dream dreams. Thirty-five years ago John Hollway conceived the idea that in the Rio Tinto ore the sulphur and iron, if properly oxidized, could be made to produce heat enough to carry on the smelting of the ores. He saw the vision. Twenty-five years ago Mr. Austin, of Montana, took out a patent on a furnace in which to carry out Hollway's ideas. He dreamed the dream. Twenty years ago a man working in Montana grasped the possibilities of this idea. To him has been given that inexpressible pleasure which comes from realizing the idea and making the concept concrete. Gentlemen, it gives me great pleasure to introduce to you the man who made the ideal real, Robert Sticht, of Tasmania. ROBERT C. STICHT, Queenstown, Tasmania.-I find it extremely difficult to act up, in the smallest degree, to the enconium passed upon me by Mr. Browne. It is true it has been my good fortune to be able to put some sort of method into the "madness" of 25 years ago; but I am not the originator of the idea, nor the only one who has carried it out. Mr. Browne mentioned the originator, who undoubtedly is Mr. Hollway. He also mentioned Mr. Austin, who gave the first instigation to pyrite smelting as now practiced. As against both of these men I was fortunate enough to be able to command the necessary natural resources to carry out the idea continuously in a practical way, so as to make it permanently possible.

Jan 4, 1915

By Basil B. Zavoico

The developments in the Russian oil industry during 1935 marked a very definite turning point from the time when the industry was being educated to the modern methods of oil-field finding and development, refining, transportation and marketing, to the time when the industry has thoroughly assimilated the modern technique and is now firmly standing on its own feet, as is shown by the remarkable qualitative, if not quantitative, progress in 1935. The oil industry promises that 1936 will be a record year in every respect with both quantity and quality approaching the desired high levels and standards. More particularly the Soviet Government is beginning to be successful in the development of new fields and such new production in geographically strategical points of the country will be in the coming years a factor of great importance in the industrial life of the country. The most notable achievements of the last year have been: the very successful development of the Ishimbaevo oil field in the Lower Oural-Permian Basin; the discovery and development of several promising oil fields in the Puta district of Azerbaijan, while large flush production of Baku area was extended 50 miles due southwest into the Saliani-Aliat district, where a 3000-bbl. well was completed early in 1936 at Pirsagat. Also, an apparently important discovery was made at Zikh, on the Apsheron Peninsula proper. These discoveries, as well as several important strikes in the deeper producing sands in the older fields of the Apsheron Peninsula, have greatly augmented the proven reserves of Russia and made them available either at the points where transportation facilities were already present or at points not too far distant from major industrial centers of the country. Of course, not all objectives were achieved during the past year, and several major difficulties remain to be solved in the coming years, the more important of which are: (1) supply of equipment and of parts; (2) the unavailability of competent technical men in sufficient numbers, which more particularly affects the distant fields; and (3) the problem of distribution of oil products throughout the country, especially the question of handling the needs of small consuming areas, which, while individually unimportant, in the aggregate require huge distribution.

Jan 1, 1936

By Basil B. Zavoico

The developments in the Russian oil industry during 1935 marked a very definite turning point from the time when the industry was being educated to the modern methods of oil-field finding and development, refining, transportation and marketing, to the time when the industry has thoroughly assimilated the modern technique and is now firmly standing on its own feet, as is shown by the remarkable qualitative, if not quantitative, progress in 1935. The oil industry promises that 1936 will be a record year in every respect with both quantity and quality approaching the desired high levels and standards. More particularly the Soviet Government is beginning to be successful in the development of new fields and such new production in geographically strategical points of the country will be in the coming years a factor of great importance in the industrial life of the country. The most notable achievements of the last year have been: the very successful development of the Ishimbaevo oil field in the Lower Oural-Permian Basin; the discovery and development of several promising oil fields in the Puta district of Azerbaijan, while large flush production of Baku area was extended 50 miles due southwest into the Saliani-Aliat district, where a 3000-bbl. well was completed early in 1936 at Pirsagat. Also, an apparently important discovery was made at Zikh, on the Apsheron Peninsula proper. These discoveries, as well as several important strikes in the deeper producing sands in the older fields of the Apsheron Peninsula, have greatly augmented the proven reserves of Russia and made them available either at the points where transportation facilities were already present or at points not too far distant from major industrial centers of the country. Of course, not all objectives were achieved during the past year, and several major difficulties remain to be solved in the coming years, the more important of which are: (1) supply of equipment and of parts; (2) the unavailability of competent technical men in sufficient numbers, which more particularly affects the distant fields; and (3) the problem of distribution of oil products throughout the country, especially the question of handling the needs of small consuming areas, which, while individually unimportant, in the aggregate require huge distribution.

Jan 1, 1936