Search Documents

By Russell G. Wayland

This paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. Muscovite Mica Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. The Mica Problem Block muscovite mica is commercially classified into the following general qualitie3, beginning with the best quality: 1. Clear and Slightly Stained (C & SS). 2. Fair stained (FS). 3. Good stained (GS). 4. stained (s). 5. Heavy Stained (HS). 6. Black spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately 1 C & SS to 4 FS to ro GS to 14 S to whatever the

Jan 1, 1948

By Lewis E. Dr. Young

MINING engineers in the United States understand that mining conditions in the British coalfields are much more difficult than in most of the mines now being operated in the United States. We realize also that in the near future we must face some of these same difficult problems. Early Mechanization The progress made in mechanical loading in the United States is the result of a long struggle in many coalfields to mine with power tools safely and to increase output per man-shift. Attempts to use power to loosen coal and to transport broken coal in the U. S. may be said to date from the Stanly Header, or Entry-Driver brought from England in 1888. The principle of this boring machine was used in the McKinlay Entry-Driver, almost continuously used in the U. S. since 1920. Since 1888 experimental loaders, scrapers, and conveyors were installed with more or less success. Beginning in 1918, considerable progress was made with mobile loaders, and in 1920 the first wage agreement for the operation of mechanical loaders was made in Indiana. In 1923 the Pocahontas Fuel Co. loaded nearly 1 million tons of coal using 23 Coloders. Labor Policy The United Mine Workers of America have never officially opposed the Mechanization movement. On December 10, 1945, in a statement before the House of Representatives Labor Committee, John L. Lewis said, regarding the policy of the United Mine Workers of America: "We have welcomed progress; we have welcomed machines. We have told our people that they had to accept that condition; that it was the process of progress, and that they would have to take their chances." Recent Development In 1951 about 71 pct of the tonnage mined underground was mechanically loaded. Over 4000 shuttle cars are in service and it is estimated that much more than half of the tonnage loaded underground is produced by trackless mining. In 1947 roof-bolting was introduced extensively and it is estimated that more than 2 ½ million bolts are now being used per month in about 600 mines. The use of roof bolts has permitted the more effective and safer use of loaders and shuttle-cars. Continuous Mining The McKinlay Entry-Driver could have been used for continuous mining, but for many years it was used only .for entry driving. In 1946 the Silver machine was developed in Colorado, and in 1947 this was acquired by the Joy Mfg. Co. and called the Joy Continuous Miner. Other types of combination mining-loading machines which eliminate drilling and blasting operations are the Marietta Miner, the Colmol, the Lee-Norse Miner, the Junior Miner, the Goodman and the Konnerth machines. There are several other types in the process of development. Probably by January 1953 there will be about 250 continuous miners in operation in the U. S. Payment of Mine Labor One of the most important problems in mechanizing was the establishing of rates of pay that would be attractive to the best men. Prior to the installation of mobile loaders the hand loaders and cutters have been paid by the ton. It was felt that a system of a day's pay should be established and that piece and tonnage rates should be abolished completely. Without exception, all coal loaded in mines equipped with mobile loaders is prepared and loaded by men paid an hourly rate. Trends in Mining Research There are two diverse approaches in coal production research; to try to design a mining machine to fit current methods, or to adapt mining practice to take advantage of proven machines. A great deal of credit must go to the mine operators who have been enterprising and dynamic enough to use available equipment intensively and to discard it as soon as an improved or new machine is available. Effect of Changing Markets Formerly there was an important demand for lump and prepared coal in the larger sizes for domestic use. The use of bituminous coal for house heating has decreased so that not more than 19 pct of the annual tonnage goes to retail trade, only 12 pct is used by the railroads, and much of the retail and most of the railroad coal is in stoker size. As a result of this decline in the market for coarse coal most of the large mining operations have crushers installed in the tipples or preparation plants. Mass production at the face requires increased preparation facilities. Another important trend is in connection with complete seam mining with mechanical loading. In many mines where the immediate roof is apt to fall with the coal no effort is made to separate roof material from coal prior to

Jan 1, 1952

By Felix A. Vogel

I (New York Meeting, February, 1912.) FLUE-DUST, to most blast-furnace operators, means a troublesome by-product, the formation of which should be curtailed, if not prevented entirely. However, with the increasing use of fine ores, larger furnaces, and high-pressure blast, the production of flue-dust is constantly increasing, and amounts annually in the United States to from 3,000,000 to 3,500,000 tons, An exceedingly high tonnage, of which a large part has been discarded as valueless. As a result of greater economy in the iron industry, the attention of our furnace-men has been directed towards the utilization of this enormous amount of waste material, a problem which had also been given due consideration by metallurgists abroad. Flue-dust is generally a fine material containing considerable coke and iron-ore, with a small admixture of lime and silica, depending upon the burden. The iron-ore is partly reduced, which shows that the dust originates largely in the reducing-zone of the blast-furnace. In the United States this dust usually contains 20 per cent. of coke and more than 40 per cent. of iron. Estimating coke to be worth $3.25 per ton, and iron-ore 7 cents per unit, a ton of flue-dust, unless made available, represents a loss to the furnace-man of $3.50. This accounts for the first efforts to recharge the flue-dust into the furnace, either by moistening it clown with an excess of water, or mixing it with clay to form balls of pulp, or treating it with lime-water. These methods, however, have been practically discarded, as they failed to produce the desired economies. To recover, in the blast-furnace, all the values represented by the material contained in the flue-dust, the following con¬ditions should be complied with

May 1, 1912

By AIME AIME

THE following compilation of State bureaus and officials that deal with mineral resources is compiled in part from a new "Check List of State Agencies and Officials Concerned with the Management of Natural Re- sources," compiled for the National Resources Committee, Washington, D. C., by Clifford J. Hynning. Alabama-Geological Survey of Alabama, University. Walter B. Jones, State Geologist. Chief Mine Inspector: W. B. Hill- house, 614 Lincoln Life Bldg., Birmingham.

Jan 1, 1939

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

By Bob J. Rawicki

TYPES OF WET DUST COLLECTORS Basically, there are two types of wettype dust collectors. One is mechanical, incorporating pumps, motors, fans, sprays, filters, or flooded beds. These come in many forms, but their operating principle is basically the same. The screen or flooded bed is wetted by a series of sprays. Polluted air is drawn in through a fan; here the dust particles impinge on the screen and are flushed off into a settlement tank. The air then passes through spray eliminators to the atmosphere. A great deal of time and money has been spent developing this type of collector. In laboratory tests where clean water at constant pressure, air at constant volume, and dust at low but constant mass to volume were applied, these collectors gave high percentage dust collection efficiencies. Theoretically and technically, they are very good. In practice, however, under rugged mining conditions where there are no constants, and dust load, particle size, water pressure, and volume of air vary with time, their efficiency varies dramatically. Some of the most common problems are: 1. clogging of screens 2. blocking of nozzles 3. replacement. of damaged pump stators Any of the above result in loss of air flow and dust collection efficiency. Generally, there are so many mechanical moving parts, something is always breaking down. This type of collector is very expensive in parts and labor to maintain. The second type of dust collector, which I personally developed, with the help of the British National Coal Board of Great Britain, has none of the above mentioned problems and it works on a completely different principle. My collector, the Mark III Precipitaire Wet-Type Dust Collector, (an improved version of previously successful models) has no internal moving parts, no flooded beds, screens, spray nozzles, etc. It is highly efficient - 99.8% efficiency on total collected dust and 97% on respirable dust. The pressure drop through the collector is constant, hence, air flow remains constant. There is no maintenance expenditure, be it labor or parts. The only maintenance that there is, is desludging. This, of course, varies with the dust load. With a low dust load, desludqinq may only be required every 4 weeks, but this is a very simple operation that can be handled by unskilled men and it takes only a very short time. My collector is powered by a ventilation fan that is placed on the clean air side for a longer fan and motor life. Dust is extracted solely by water action. The collector's operating principle is: Dust laden air is drawn in along ducting into a tapered scrubber section, shaped to create a self-induced curtain of water. This action washes the dust particles from the air and the collected dust settles into the bottom of the tank. Cleaned air is then exhausted via a series of spray eliminators where it is completely dried and on into the atmosphere. These collectors have been sold in Great Britain, to the National Coal Board, and throughout Europe. They have been working very well for many years now. GENERAL APPLICATIONS Dust is very dangerous; silicosis and black lung kill and disable many workers each year. Many of the mine explosions can be attributed to coal dust. By the use and application of dust collectors, these deaths and disasters can be avoided. There really is no excuse. However good and efficient a dust collector may be, it's positioning and installation arrangement is critical. The collector may remove 99% of dust supplied to it, but it takes the skill and experience of a dust control engineer to design and fit ducting, hoods, etc. to remove polluted air at source and deliver it to the collector. In some cases this is very simple; in the case of longwall machines, it is very difficult. In general, dust collectors should be used to collect dust at every point of dust generation. I have noted a great reliance on dilution as a means of dust control. I personally think this is a dangerous and unreliable method. As mines become deeper and the use of larger and more productive equipment becomes more common, reliance on dilution will be impossible and dust collectors will be essential.

Jan 1, 1982

By C. F. Willis

The problem of the curtailment of forces in large numbers does not often come to employment departments and is, therefore, a problem that many departments are not prepared to handle intelligently. Those companies that are able to measure the individual efficiency of each man would probably lay off men according to their individual ability, irrespective of dependents, citizenship, or other considerations. During the war when labor was scarce, the business of the employment manager in industry was hiring men and carefully placing them where they were best fitted to work. The careful selection of employees had developed to a considerable extent before the war, and was becoming a recognized science. In the last few months, however, the cancelation of copper contracts, the accumulation of large stocks, the necessary curtailment of production because the copper could not be sold, and the lack of any immediate prospects of' the copper market opening, have led to a universal reduction of forces, and the problem that industry now confronts is that of discharging rather than employing. The problem has been aggravated by the cancellation of contracts in many war industries with the consequent turning loose of hundreds of thousands of men, a great amount of unemployment, and the return of the soldiers and sailors. The problem has now become one of reduction of working force with the least hardship and the least injustice, and yet caring for the soldiers, sailors, and marines who have been in the service of the government for nearly 2 years, and are now returning to their pre-war positions. The Copper Queen Branch of the Phelps Dodge Corpn., operating at Bisbee, Arb., found it necessary, like all of the other copper companies of the country, to reduce its force materially. In making this reduction it was, after due consideration, decided to classify employees with respect to dependents, length of service, and citizenship. The question of individual efficiency or workmanship was not considered. Copper produced to sell at 26 c. a lb. has been selling at under 15 c., and very little copper is being sold at all. Practically every copper producer in the country has enormous stocks on hand, and it would be profitable,

Jan 1, 1920

G. D. Kneip, Jr., and J. 0. Betterton, Jr. (Union Carbide & Carbon Corp., Oak Ridge, Tenn.)—The authors have contributed to the theory of zone melting by considering the effects of the solidification of the final zone on the distribution curves for the finite length bar. However, they do not consider in sufficient detail the restrictions imposed by the particular metals involved. Eq. 4 has the analytical solution which is equivalent to Pfann's' equation for normal solidification of the final zone. For distribution coefficients less than one, it is apparent from this form of the equation that, as the solidification approaches completion, the concentration attains extremely large values which are inconsistent with the density of physical materials. The necessary restrictions then are that the solute concentration cannot exceed the density of the alloy, or more frequently, the solubility limit in the solid phase. Secondly, the distribution coefficient cannot be constant from 0 to 100 pet solute unless the liquidus and solidus coincide over this whole region. It would thus be more correct to impose limits on the solubility such as would be indicated by a typical eutectic diagram. Furthermore, in this case the assumption that the distribution coefficient remains constant is more likely to be realized. Eq. 4 should then be replaced by the following C,,(x) =k/L-x [ ?11 3 C11 (x)Ddx - ?11 4 Cn(x)dx= k[Cn (L-l)/k] [ L-x/l]x-1 L-l = x = L-l [kCenterlie/Cn (L-l)]1/k-1 The typical shape for the distribution curve in the final zone is indicated schematically in Fig. 12 for the simple eutectic case. The solidification proceeds according to Pfann's' expression until the concentration reaches the maximum solubility in the solid phasc. At this point, the concentration changes abruptly to the eutectic composition and remains at this value for the duration of the solidification. The width of the flat region, and the back reflection of this effect into the concentration curve on subsequent passes, depends upon the ratio of the eutectic concentration to the original concentration, upon the distribution coefficient, and upon the number of passes. Similar effects on the concentration curves in the first zone length would be expected in many systems for which the distribution coefficient is greater than one, and where the maximum solubility is not too much larger than the original concentration. The discussers agree with the authors that the assumption that the liquid is uniform in concentration should be considered with caution. Kneip and Better-ton' have shown, however, that in floating zone refining of zirconium, using induction heating, the distribution of iron agrees with theory which assumes a uniform liquid composition. Hence, in this case, the experimentally realized distribution coefficient agrees with the present phase diagram within the experimental uncertainty. L. Burris, Jr., C. H. Stockman, and I. G. Dillon (authors' reply)—The authors are happy to have received the comments of G. D. Kneip, Jr., and J. 0. Betterton, Jr., which provide additional insight into the zone refining process. It is true that the equations developed are inapplicable if the solute solubility in the solid phase is exceeded. However, this restriction on the use of the equations was clearly stated in the paper. A closer approach to

Jan 1, 1957

By R. W. Diamond

Low-grade ores can be designated by two main classifications: (1) simple low-grade ores, and (2) complex low-grade ores. As a rule the first type has a relatively small metal content, although low- grade iron ores contain a rather high percentage of metal. As the simple type is the one that is ordinarily in mind when the term "low-grade ore" is used, the paper will be devoted mainly to ores in this general category. Cheap treatment is the prime requirement in utilizing low-grade ores of the simple type, although in some cases the value of nonmetallic by-products, such as limestone for fer- tilizer and silica for flux, allows a little more lati- tude than in the usual situation. When the costs are divided under the three headings-mining, milling, and smelting-it is apparent that the last group will not constitute an important factor as a rule because the high concentrating ratio makes the smelting cost per ton of ore fairly low.

Jan 1, 1949

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By John R. Green

Rotary kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary accorcling to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. Measurements of Kiln Temperature The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records ox automatic control are desired, while Optica1 pyometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. 1 shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected From puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly 0" to over zoo°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without effect of the flame temperature. There should some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and comments on the possibility of measurement and control. Of greater number and of varied influence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1942

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

By J. S. Fulton

THOSE who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangement, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartment septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries) ; portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. PHASES Of the many papers published on various phases of the Bessemer process, nearly 170 according to one bibliography, over go per cent were concerned with the metallurgical phase and less than 10 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to one of the causes of the Bessemer process. Is it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By Dr. O’Neil Thomas J., Donald W. Gentry

"There is nothing so disastrous as a rational investment policy in an irrational world. " John Maynard Keynes INTRODUCTION The principles of time value of money concepts were discussed and illustrated in Chapter 3. The importance of time value of money and the role it plays in the discipline of engineering economy have been well established. Chapter 9 further illustrates that project evaluation criteria that fail to consider this aspect are seriously deficient in providing appropriate capital budgeting decisions. Obviously future project receipts and expenditures must be discounted to permit valid comparisons with current cash flows. Although the concept of discounting is widely accepted, the selection of the appropriate discount rate has been the source of considerable debate and much disagreement. This chapter, then, provides an overview of the theoretical and practical considerations for determining or calculating the appropriate rate for discounting, the corporate cost of capital. Note specifically that the assumption of constant business risk among the various investment alternatives is maintained throughout this chapter. THE INTUITIVE APPROACH The fact that interest exists suggests that all money has a cost associated with its use. The cost of this money may be the result of either explicit or implicit charges or some combination of the two. Any time an individual or a firm consumes less than the total earnings generated in a given time period that individual or corporation has either consciously or unconsciously decided to "invest" these excess funds in some type of activity. For instance, the individual or corporation may decide to invest the excess funds in tangible property, place the funds in a money market account, or simply keep these funds in cash. In any case, these funds have been invested in some type of activity which promises the investor some return on the invested capital. Remembering that the firm's primary objective should be the maximization of shareholder wealth, then intuitively it seems reasonable to suggest that the firm should not invest in any project where the anticipated return does not exceed the cost of funds (capital) committed to the project. Indeed, if the firm always invests in projects having returns in excess of the cost of capital committed to them, then the wealth of the firm (as measured by the price of common stock) should be in-

Jan 1, 1984

By Gill Montgomery

The strong upward curve of fluorspar consumption continued through 1968, with domestic producers unable to furnish more than 30% of U.S. requirements. Stocks of all grades were quite short at all points during most of 1968. This resulted in price increases as both domestic and foreign producers sought to cover spiralling labor costs. Further increases are probable for 1969. All Illinois mines were closed by strikes in January and February. The strong trend in metallurgical imports reflects the increased use of fluorspar in steelmaking, as new oxygen process steel plants come into production. The growth of use of all fluorocarbon chemicals continues to require additional acid grade fluorspar, with military uses a major factor. Several new aluminum smelting facilities coming into production are adding to the aluminum fluoride needs, bringing further pressure upon the world supply of acid grade fluorspar. The world-wide consumption pressure on all grades of fluorspar is pushing prices up, and no end to the tight supply is in sight, even assuming that all the new projects cited here are finished on schedule.

Jan 3, 1969

By Jun-Yan Chen, Stefan H. Boshkov

Metal mining in the People's Republic of China has shown great growth during the last three decades. Over 150 new iron ore mines and nonferrous base metal mines have been opened since 1949, althouc.11 most of them of medium and small size. Concurrently, many old mines were enlarged and reconstructed. The production of iron ore has grown from less than 1.5 million tons per year in 1949 to almost 76 million tons in 1978. A corresponding increase in the total annual output in the nonferrous metal mineral industry has also been noted. It is well known that the PRC is very rich in metal mineral resources. The reserves of tungsten, tin, antimony, molybdenum and iron ore are ranked in the top three in the world. Recently, some copper porphyry ore deposits were discovered in Jianxi and Anhui provinces. Some large nickel-copper sulfide deposits were discovered and have been developed in North- West China. Huge iron ore deposits have been found in Liaoning, Hebei and Szechwan provinces. However, the bulk of the iron ores are low grade. The growing metal mineral production has met basic domestic needs since 1949; it has also proven China's big resource potential. Mining methods have also undergone development in the past 30 years. About 80% of the annual output of iron ore comes from open pits, whereas about 58% of nonferrous metal ores come from underground mines. Blasthole open stoping, sublevel caving and induced block caving are widely used in Chinese underground metal mines (table 1). This paper summarizes in detail the planning for and application of these three bulk mining methods in the nonferrous and iron ore mines in China. CLASSIFICATION OF UNDERGROUND MINING METHODS The main principle of the classification of underground mining methods in PRC is ground support in the stoping cycles of the mining blocks or stopes. Table 2 lists this classification. It is essentially the same as that given in the SME Mining Engineering Handbook. Be- cause pillar removal is a secondary mining operation, using a variety of methods, they are not included in this classification. As is the case with most classifications in science and technology, there is no precise division between the classes of mining methods. Because of the rapid development of consolidated filling techniques in the past twenty years, some types of open stoping methods use fill in order to improve the ground conditions for the secondary recovery stage. Thus, these mining methods have features of both methods using no artificial support and those using artificial support. In this classification, this type of mining method is placed in the latter category. The shrinkage stoping method has been employed extensively to mine steeply dipping narrow veins of tungsten and tin in the Jiangxi, Hunan, Guangdong and Guangxi provinces. Shrink- age stoping is placed under the class of mining methods without artificial support be- cause this reflects the nature of the Chinese experience. The function of the broken ore serving to support the footwall and/or hanging wall is limited, because the expectation is for the host rocks to remain unsupported until the stope is drawn empty. APPLICATION OF BULK MINING METHODS Bulk mining methods consist of blasthole open stoping, sublevel caving and block caving. These stoping methods have much in common, such as: bulk ore materials blasted by long holes; higher production rates of stopes or blocks and higher production efficiencies of the whole mining systems.

Jan 1, 1981

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By John V. Hamme

ONE of Tungsten Mining Corp.'s Vance County, N. C., mill near Henderson was the installation of a new crushing plant with a capacity of 45 to 50 tph. During 1953 the milling rate was jumped from 650 tons to 800 tpd simply by expanding existing facilities, eliminating bottlenecks, and making changes in the existing and new circuits. Previous expansions in 1951 and 1952 raised mill capacity from 300 tons to 650 tpd. In its latest move, Tungsten Mining decided that expansion of existing facilities would be more economical than building that normal production was uninterrupted. For the engineering and design of the new crushing plant and mill expansion the services of the Southwestern Engineering Co., Los Angeles, were obtained. The Southeastern Construction Co., Charlotte, N. C., carried out construction, alterations to existing facilities, and the installation of equipment

Jan 10, 1954