Search Documents

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.' Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2'4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy's equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.' were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By W. R. Crane

The support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact, the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident, then, that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 1, 1925

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By A. J. M. Ross

Backfilling of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35" to 40' to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1940

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of open-ings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35° to 40° to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transporta-tion of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars prac-tically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of openings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35º to 40º to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transportation of this fill over the top of the stopes as mining progressed The cost of maintaining these crosscuts was excessive and in many pillars practically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939

The following paragraph of appreciation of the Engineering Societies Employment Bureau is from the letter of a young engineer who found the Bureau of service. "I wish to sincerely thank you for the services rendered. They are of immense value to anyone located as I am, in a small town without the opportunities for keeping in touch with openings in manufacturing lines."

Jan 12, 1919

By A. H. Larson, R. J. McClincy

The activity of Sb,03 in PbO-Sb,03 slags containing less than 50 mol pct Sb,03 was determined by the inert-gas saturation method at 700°C. In this composition range, the activity gf SbzO3 shows a strong negative deviation from ideality. The activity of PbO in these slags was calculated by application of the Gibbs-Duhem iniegration to the Sb203 activity data. The calculated activity of PbO in slags containing more than 63 mol pct PbO was found to deviate in a positive direction from ideality uthile a negative deviation was found for slags containing less PbO. The standard Gibbs free energies of formation of Sb,03 and PbO. Sb203 have been calculated and compared with existing data in the literature. The activity of Sb203 in PbO-Si0,-Sb203 (PbO/SiO, = 2) slags containing less than 25 mol pct Sb,03 was also determined by the inert-gas saturation method at 700°C. In this composition range, the activity of Sbz03 shows a very large negative deviation from ideality. VERY little experimental work has been published in the past to determine equilibrium data in the oxide systems connected with the refining of lead. These data are of value since impurities such as antimony, arsenic, and tin must be removed from lead and recovered for further treatment. Equilibrium studies on antimony and arsenic systems are also of interest for the design of new processes for lead refining and lead dross treatment. Maier and ~incke' first determined the liquidus curves for the PbO-Sb203 system and identified the compound PbO . Sb203. They found the phase diagram for this system to be two simple eutectics located on either side of the congruent melting compound. They also determined a very limited amount of vapor pressure data for Sb406 abbve PbO-Sba3 melts at 697"~. A second phase diagram investigation on this system was reported by Hennig and Kohlmeyer' who confirmed the existence of the compound PbO . Sb203 as well as the form of the diagram. A disagreement was noticed, however, in that their liquidus temperatures over nearly the entire composition range were higher than those reported by Maier and Hincke. Barthel~ and pelze14 redetermined the liquidus curve at the PbO-rich end of the PbO-Sb@, system and agreed very closely with the results of Maier and Hincke. None of the investigators mentioned above reported any mutual solid solubility in the PbO-SbD3 system. Zunkel and Larson5 have determined the phase diagram for the PbO-rich end of the PbO-Sb203 system by slag-metal equilibrium studies in the Pb-PbO-Sb203 system and by thermal analysis studies in the PbO-Sbz03 system. A maximum solid solubility of 5.6 mol pct Sb203 in PbO was observed at the eutectic temperature of 604°C. Their results for the phase diagram agree favorably with those of Maier and Hincke. The vapor pressure of Sb2O3 in the temperature range from 470" to 800°C has been determined by Hincke, using a modification of the transportation meth~d.~ His results for temperatures below the melting point of Sba3 are the only data reported in the published literature. The predominant vapor species has been shown to be Sb,06 by Norman and staley.? Myzenkov and Klushin,8 using the boiling-point method, have determined the pressure of Sb406 above liquid SbD3 in the temperature range from 715" to 1025°C. The agreement between these two studies is not very close. A portion of the discrepancy lies in the fact that Hincke used silica crucibles, which were attacked by the liquid Sbz03 at high temperatures. This fact does not account, however. for the large difference observed at the melting point. ~aier' gives a brief summary of vapor pressure data for Sb,O, above pure liquid Sbz03 which agree quite well with the data of Myzenkov and Klushin at temperatures near the melting point. This paper describes the determination of Sb2O3 activity data in the PbO-Sb203 and Pb0-Si02-Sb203 (PbO/SiOz = 2) systems by the inert-gas saturation method. These activity data are compared with the data calculated by Zunkel and arson. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade PbO (99.8 pct PbO, 0.14 pct insoluble in CHsCOOH, 0.02 pct not precipitated by HB, 0.1 pct CaO, and 0.08 pct SiOz), Sbf13 (99.6 pct Sb203, 0.004 PC~ C1-, 0.005 PC~ SO;-, 0.15 p~t AS, 0.001 pct Fe, and 0.03 pct other heavy metals such as Pb), and SiOz (chromatographic grade). Apparatus for Vapor Pressure Determinations. The apparatus used in this investigation consisted of a transportation reaction system with two separate gas trains. The argon transporting gas was first mixed with a small amount of hydrogen, metered, and dried by passage through silica gel and anhydrone drying tubes arranged in series. After this preliminary drying, the argon was passed through copper wool at 500°C to convert the residual oxygen to water vapor which was removed by three anhydrone drying tubes. A second stream of argon was metered and dried and then passed around the outside of the alumina reaction tube to flush away the volatile species to pre-

Jan 1, 1970

By John H. Harden

In the valuable paper of Mr. Dunbar D. Scott and its varied discussion, on the evolution of mine-surveying instruments, the tripod-head has not received the attention it merits. During the last 50 years this very necessary adjunct to the surveyor's instrument has been much improved. The legs are of better construction; and the devices for laterally moving the instrument over the station-point and for quick leveling, without the use of the screws, have given to the instrument fitted with the modern tripod-head the same facilities possessed by the oldfashioned ball-and-socket, with more perfect accuracy, not attainable in the latter, while saving from 30 to 50 per cent. of the time required for setting the instrument over a station. For the purpose of extending the discussion to this import-

Jan 1, 1902

By Carl E. Swartz

In the course of a recent investigation1 to develop a more satisfactory white-metal bearing alloy, a number of alloy systems were studied. The cadmium-nickel system showed characteristics desirable in a bearing alloy, and the system was therefore studied in some detail. Experimental Method Alloying cadmium with nickel offered no serious difficulty. After melting the cadmium, clean sheet nickel was added while the temperature was maintained at 500" to 600" C. A few crystals of ammonium chloride2 served to clean the nickel when the latter did not "wet" readily. In preparing the individual alloys for thermal and microscopic investigation, a "hardener" containing about 10 per cent nickel was used. Thermal Experiments and Apparatus Time-temperature cooling curves were made by standard methods. Globe electrolytic cadmium was added to the hardener to make a melt of the desired composition weighing between 100 and 200 grams. This charge was placed in a Pyrex test tube, 1 by 10 in., closed with a rubber stopper carrying a thermocouple sheath and quartz stirring rod. The assembly was lowered to a depth of about 4½ in. into an electric resistance pot furnace containing a No. 0000 clay-graphite crucible (to catch the melt in case of a break in the test tube). After the tube was clamped in this position, an asbestos-magnesia mixture was loosely packed in the furnace around the tube and a "halved" cover of transite placed on top. This left at least 5 in. of the test tube protruding from the furnace. When the alloy had melted, the thermocouple was adjusted so that the hot junction was l! in. from the bottom of the test tube. The melt was stirred thoroughly for several minutes to insure composition homogeneity and absence of thermal gradients.

Jan 1, 1934

By John M. Kelly

New Mexico produced 39,751,868 bbl. of oil in 1941 and ranked seventh among the oil-producing states. Its 1941 production established an annual record, exceeding the 1940 record year by 854,498 bbl. The average daily production for the year was 108,909 bbl. The average daily non-marginal well allowable for New Mexico on Jan. I, 1941, was 36 bbl.; at the close of the year it was 43 bbl. The average daily pipe-linc runs were approximately 3 per cent less than the allocations of the New Mexico Oil Conservation Commission, which followed closely the recommendation of the United States Bureau of Mines in setting the daily outlet demand. The production in Lea County was 34,333,448 bbl.; Eddy County, 5,009,354 bbl.; and northwestern New Mexico (San Juan and McKinley Counties), 406,306 barrels. The total number of completions in the state was 402, of which 301 were oil wells, 19 gas wells, and 82 dry holes. Drilling during 1941 was 68 per cent of 1940, and the ratio of dry holes to producers, I to 4, was the greatest since 1935. Of these dry holes 43 were drilled in proven fields and 39 were wildcats. One new oil field and one new gas field were discovered as a result of the 1941 wildcatting program. However, numerous extensions were made to the existing fields, which, although they were called extensions to proration areas, were in reality field discoveries, being on separate geologic structures. Southeastern New Mexico Lea County The Monument field was the largest producing field in Lea County, with 6,973,808 bbl. It was closely followed by the Eunice field, with 6,644,181 bbl.; Vacuum field, with 4,800,608 bbl. and Hobbs, with 3,624,159 bbl. Hobbs field, however, still has the largest total recovery, this being 97,407,929 bbl. at the end of 1941. The new oil-field discovery in Lea County during 1941 was the Salt Lake field, T. 20 S., R. 33 E. The discovery well was Leonard-Welch State No. I, NW. NW. of sec. 18, T. 20 S., R. 33 E. This well was drilled to a total depth of 3103 ft. and was completed for an initial production of 250 bbl. per day pumping. The oil is 26" gravity and the producing horizon is in the San Andres limestone of Permian age. The discovery well was completed on June 22, 1941, and since that date four more producers have been completed, with no failures. The area is about 10 miles north-west of the Lynch pool, to which the oil from this field is being trucked because there is no pipe-line connection. The greatest drilling activity during 1947 was in the Maljamar field of western Lea County, with 62 completions, 59 being oil wells and 3 dry holes. The limits of this pool are now being defined on the north and south but to date have not been defined either to the east or west. The total number of 40-acre oil-producing units in the field at the close of the year was 158. On April I, 1941, a pressure-maintenance project was installed at the southern end

Jan 1, 1942

By John M. Kelly

New Mexico produced 39,751,868 bbl. of oil in 1941 and ranked seventh among the oil-producing states. Its 1941 production established an annual record, exceeding the 1940 record year by 854,498 bbl. The average daily production for the year was 108,909 bbl. The average daily non-marginal well allowable for New Mexico on Jan. I, 1941, was 36 bbl.; at the close of the year it was 43 bbl. The average daily pipe-linc runs were approximately 3 per cent less than the allocations of the New Mexico Oil Conservation Commission, which followed closely the recommendation of the United States Bureau of Mines in setting the daily outlet demand. The production in Lea County was 34,333,448 bbl.; Eddy County, 5,009,354 bbl.; and northwestern New Mexico (San Juan and McKinley Counties), 406,306 barrels. The total number of completions in the state was 402, of which 301 were oil wells, 19 gas wells, and 82 dry holes. Drilling during 1941 was 68 per cent of 1940, and the ratio of dry holes to producers, I to 4, was the greatest since 1935. Of these dry holes 43 were drilled in proven fields and 39 were wildcats. One new oil field and one new gas field were discovered as a result of the 1941 wildcatting program. However, numerous extensions were made to the existing fields, which, although they were called extensions to proration areas, were in reality field discoveries, being on separate geologic structures. Southeastern New Mexico Lea County The Monument field was the largest producing field in Lea County, with 6,973,808 bbl. It was closely followed by the Eunice field, with 6,644,181 bbl.; Vacuum field, with 4,800,608 bbl. and Hobbs, with 3,624,159 bbl. Hobbs field, however, still has the largest total recovery, this being 97,407,929 bbl. at the end of 1941. The new oil-field discovery in Lea County during 1941 was the Salt Lake field, T. 20 S., R. 33 E. The discovery well was Leonard-Welch State No. I, NW. NW. of sec. 18, T. 20 S., R. 33 E. This well was drilled to a total depth of 3103 ft. and was completed for an initial production of 250 bbl. per day pumping. The oil is 26" gravity and the producing horizon is in the San Andres limestone of Permian age. The discovery well was completed on June 22, 1941, and since that date four more producers have been completed, with no failures. The area is about 10 miles north-west of the Lynch pool, to which the oil from this field is being trucked because there is no pipe-line connection. The greatest drilling activity during 1947 was in the Maljamar field of western Lea County, with 62 completions, 59 being oil wells and 3 dry holes. The limits of this pool are now being defined on the north and south but to date have not been defined either to the east or west. The total number of 40-acre oil-producing units in the field at the close of the year was 158. On April I, 1941, a pressure-maintenance project was installed at the southern end

Jan 1, 1942

By Robert H. Carpenter

Molybdenite mineralization occurs in the hood zone of the Questa mine aplite-porphyry intrusive, one of the three sil ica-rich intrusive5 occurring along the east-west trending Red River Trench that crosses the northerly trending Sangre de Cristo Mountains in north-central New Mexico. The Trench is located immediately north of the circular Gold Hill positive block between the Red River and Cabresto Creek drainages. The aplite-porphyry bodies intruded a mid-Tertiary volcanic section consisting of lower andesites, overlain by latites and rhyolites. They occur largely in the andesites and were emplaced mainly by metasomatism rather than by sloping. Hydrothermal alteration occurs both as blanket propylitization in the volcanics and sericitization and kaolinization in the porphyries and as halo-type alteration outward from veins and shear zones resulting in strong biotization in the volcanics and sericitization and kaolinization in the aplitic rocks. Mineralization consists of: ( 1) molybdenite- quartz veinlets; (2) banded molybdenite, quartz veins frequently with biotite and potash feldspar along the walls and occasionally with minor lead, zinc, and copper sulfides and with fluorite and carbonates when again reopened; ( 3) high grade molybdenite locally along shear zones; and ( 4) molybdenite paint along joint and fracture surfaces. The mineralization was associated with faulting that resulted from numerous periods of gravity adjustment along the Trench and was controlled by the major shear systems that trend northeast, east-west and north-south to northwest. Molybdenite has been well oxidized in nearsurface exposures to ferrimolybdite and the molybdenum-bearing ferric hydroxide, akaganeite. The oxidation of the abundant pyrite within the veins and shear zones and of the alteration pyrite in the volcanics resulted in a low pH environment under which the acid molybdate ion released by oxidation was fixed either in the ferrimolybdite or the akaganeite molecule in the veins and shear zones or in the soils. Little has been lost in the runoff.

Jan 1, 1968

By Roshan B. Bhappu, Ronald J. Roman, Dexter H. Reynolds

The reaction between manganese dioxide and molybdenite in a water- sulfuric acid medium was studied at atmospheric pressure and from 25° to 103°C. Both solids are dissolved to give, as final products in solution, Mo(VI), S(VI), and Mn(II). Stoichiornetric relationshifis are most simply represented by the equation MoSz + YMnO2 + 15H+ - HMoO-4 + 2HSO-4 + 9Mn++ + 6H20 The rate of this reaction was found to be dependent on temperature, manganese sulfate concentration, acid concentration, and, in a complex way, the surface areas of both manganese dioxide and molybdenite. Both the total amount of manganese dioxide and tnolybdenite and the ratio of manganese dioxide to molybdenite played a part in determining the over-all rate of the reaction. The effect of acid concentration on the rate was also dependent on the ratio of manganese dioxide to molybdenite. SEVERAL reports in the literature describe reactions using manganese dioxide in water-sulfuric acid media as an oxidizing agent. Nearly all previous work describes interactions between an ion and manganese dioxide, such as the oxidation of ferrous to ferric iron,' or the interaction between a molecule in solution and manganese dioxide, such as the oxidation of toluene to benzaldehyde.2 Only a few references describe the use of solid manganese dioxide to oxidize another solid in sulfuric acid. One report3 states, "Manganese dioxide in dilute sulfuric acid solutions had no beneficial effect (in leaching copper from chalcopyrite), but in more concentrated acid solutions the rate of solution was about the same as that for permanganate." In 1902 a German patent4 described a process which used manganese dioxide in strong (50°Be') sulfuric acid for oxidizing chromite ores to soluble iron and chromium salts. The process consisted of mixing the sulfuric acid with the finely ground ore and manganese dioxide. The pulp was then heated to about 120°C and an electric current passed through it. The manganese dioxide apparently dissolved in the strong, hot acid solution, oxidized the iron and chromium and itself was reduced to manganese 11! then was oxidized at the anode back to manganese dioxide, and the cycle repeated. An extensive study5 of the kinetics of the oxidation of pyrite with manganese dioxide indicated that in dilute sulfuric acid solutions (about 0.1 N) and at elevated pressures the dissolution of the pyrite was brought about by air oxidation of the iron to ferrous sulfate, followed by manganese dioxide oxidation of the ferrous sulfate to ferric sulfate. The mechanism proposed by the authors involved the oxidation of the iron at the surface of the manganese dioxide. Also! the oxidation of sulfide sulfur to sulfate was credited to the oxygen in the air, not to the manganese dioxide. Since the metallurgical literature is lacking in information concerning the use of one solid to oxidize another solid. the current investigation was under-

Jan 1, 1965

By T. R. A. Gokcen

THE possibilities of separating and purifying metals by high vacuum distillation were examined by Kroll.1 He suggested vacuum treatment for the removal of zinc from the lead produced after Parkes desilverizing. The St. Joseph Lead Co. developed the first commercial vacuum dezincing process at their Herculaneum refinery, as described by Isbell.² The Broken Hill Associated Smelters at Port Pirie, Australia, has, after several years of pilot plant operations and fundamental investigations, developed a continuous process, which will be described briefly in a forthcoming publication." As the full-scale continuous vacuum dezincing plant at Port Pirie is still experimental, publication of full practical details of the plant will be deferred until the unit is operating as a normal part of the continuous refinery. This paper deals only with theoretical aspects of vacuum distillation processes, with particular reference to vacuum dezincing. The method of mathematical analysis is of general interest as it may be applicable to other metallurgical separations which have been investigated recently.4-6 Evaporation Processes At about atmospheric pressure, or higher, most liquids possess a boiling point—a temperature at which any heat put into the liquid is absorbed only as latent heat, not as specific heat. If a steady heat input is supplied, the liquid's temperature rises to this value, then remains constant while bubbles of vapor form beneath the surface. The rate of evaporation is determined solely by the rate of heat transfer to the liquid; the temperature of boiling is determined by the partial pressures of the volatile constituents in the liquid, and the total pressure above the surface. If the rate of heat transfer to the liquid is increased, the temperature remains constant, and the rate of boiling increases. When evaporating metals under vacuum, however, the partial pressures concerned are generally so small that boiling does not occur, because at even a fraction of a millimeter below the surface the hydrostatic pressure is usually too great to permit the formation of a pocket of vapor. In addition, the high thermal conductivity of metals tends to prevent the local superheating which is necessary for bubble formation.' Although this effect is doubtless also exerted when boiling metals at higher pressures, the magnitude will be less because the degree of superheat required to form bubbles is very much less at the higher temperatures involved. Under vacuum, therefore, evaporation of volatile constituents takes place only from the exposed surface, and the rate of evaporation depends upon the surface area, the surface concentration of volatile constituents, the surface temperature, and the partial pressures of volatile constituents immediately above the surface. If the heat input is raised above a certain level, the effect is not to increase the evaporation rate at constant temperature, but to raise the temperature of the liquid until at some higher level an increased rate of evaporation (and thus of latent heat absorption) again balances the heat input rate.? Many substances (including metals) have a very large intrinsic evaporation rate at quite low temperatures—far below their normal boiling points. However, at atmospheric pressure, the large numbers of atoms evaporated are almost completely deflected back into the liquid (or solid) surface by air molecules. Thus the back condensation rate is practically equal to the gross evaporation rate, and the net evaporation rate is practically zero. It can therefore be seen that an overall distillation rate depends not only upon the intrinsic evaporation rate, but also upon the ability of the volatile atoms to move away from the evaporating surface. This movement is facilitated by the provision of a condensing surface close by. Vacuum Distillation: The function of the vacuum above the evaporating surface is to remove foreign molecules, so that the chances of deflection of an evaporated atom back into its source are reduced. When the residual gas pressure is reduced so far that the evaporated atoms have a high probability of reaching a nearby condensing surface without suffering collision with a foreign molecule, the state of affairs is termed "molecular distillation." This process is practiced commercially today for the purification of numerous organic chemical products of high unit value, but not, to the writer's knowledge, for any metallurgical separation. When the degree of vacuum produced in a still is not sufficient to promote molecular distillation, then the evaporated molecules must diffuse through the

Jan 1, 1954

By Nicholas J. Grant, Rolf Nordheim, Thomas B. King

Constant-load creep-rupture tests were conducted in an argon atmosphere at temperatures of 1600 to 2200°F on two heats of iron containing about 0.06 and 0.09 pct P in solid solution. The tests were conducted in the as-cast condition. Stresses were selected to give strain rates approaching those encountered in the hot working of steel, and within the limits of the creep-rupture test apparatus, namely. from about 0.001 to 50 pct per sec. FOR generations, rolling and forging practices have been developed largely by empirical methods, based on prior experience. While largely successful, difficulties are frequently encountered when new or different alloy compositions are tried for the first time. There is need to know the relationships which exist among temperature, strain rate, composition, and other variables on the deformation and fracture characteristics of steels. It has been shown for aluminum and several high-temperature alloys that the deformation and fracture characteristics follow rather well-defined laws and patterns which are closely related to the effects of strain rate, temperature, and composition.1"3 As the melting temperature of aluminum or its alloys was approached, it was possible to study the interplay of work-hardening factors and recovery or recrystal-lization, the latter resulting in improved ductility and increased resistance to intercrystalline fracture. In particular, the effects of composition are very poorly known. Within the meaning of "composition" should be included impurity elements, such as sulfur, phosphorous, lead, copper, and many others, as well as those elements which are added for alloying purposes in iron. The role of multiphase structures, in contrast to solid solutions, should also be studied in much greater detail. high strain rate creep-rupture tests would provide information regarding the deformation and fracture characteristics of metals at hot-working temperatures. It was also desired to establish the stresses which are necessary to accomplish the desired deformation, and to relate these to the strain rate and temperature. Secondly, it was the purpose of this particular study to determine the effects of phosphorus, within solid solution limits, on the deformation and fracture characteristics of iron at hot-working temperatures. EXPERIMENTAL PROCEDURE Two phosphorus levels were selected, one corresponding to the upper limit normally found for commercial steels, and one substantially higher than this, but within the region of solid solubility at the test temperatures chosen for this investigation. Twenty-pound heats were prepared by induction melting electrolytic iron in air in a magnesia lined furnace. After deoxidation with about 0.2 pct Al, ferro-phosphorus was added, and the heats were then poured into prefired silica molds. The purpose of using silica molds was to obtain a slow cooling rate during solidification to produce a relatively coarse grain size, producing a structure subject to some segregation and therefore more nearly characteristic of ingot structures. The major part of the casting assembly provided a large shrinkage head in order to produce sound castings and to promote slow cooling of the specimens. The primary austenitic grain size varied from ASTM No. 2 to No. 00. The composition of the heats, including a low phorphorus melt, used for comparison purposes, is shown in Table I. It will be noted that the oxygen content of the phosphorus containing heats is relatively high, in spite of the deoxidation practice, a condition which is difficult to control in small melts. Creep-rupture tests were nevertheless undertaken when it was noted that this quantity of oxygen did not appear to give results any different from those from a heat containing 0.01 pct 0, low phosphorus and comparable carbon Content;4 see Table 11.

Jan 1, 1961

By Herman Garlichs

THE development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately, $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870: Lead production in South-west Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 ,tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a V. Wood and galena were placed in the furnace and ignited. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 ft. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required, for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 7, 1917