Search Documents

By E. F. Miller

The subject " Safe Timbering of Working Places in Mobile Loading" is one that requires an analytical study of the strata both above and below the coal seam as well as the characteristics of the coal seam itself. The projection or mining plan must be based on economic roof control in which the application of timber can be minimized without incurring cost increases in other phases of production. The several types of loading machines in common use today are not adaptable to the same projections or timbering systems. Consequently the type of equipment to be used must also be considered. For these reasons the writer does not believe that the problems of timbering in working places can be discussed without simultaneously considering economic production as well as the safety of men and the conservation of equipment. Prior to the introduction of loading machines as a substitute for the pick and shovel system of loading coal, the care and maintenance of the individual working places were generally the responsibility of the coal loaders who worked in them. Up to that time very few coal companies had developed and applied fixed and definite standards for timbering the working places in the mines they operated. It is common knowledge that mechanical loading of coal has had several false starts in the last twenty-five years and it is only in the last decade that it has developed to the stage at which we now find it. During this twenty-five year period the management of the more responsible companies have come to realize the tremendous importance of roof control in coal mining. From a safety viewpoint, the lack of roof control has been and still is responsible for more than a third of the industry's annual fatality experience. In recent years workmen's compensation and insurance rates have steadily increased while the profit margin has decreased almost to the point of elimination. From an economic operating viewpoint, the failure to properly control roof is quite often the most costly single phase of coal mining. Since the manufacturers of loading machine equipment have so improved their machines that normal care and maintenance can reduce to a minimum the time lost because of mechanical failure the production delays from other causes have assumed a far greater importance. Roof control in the broad sense and in the light of concentrated mining plans or projections that are adapted to mobile loading should be regarded as one of the major problems in the inseparable phases of production and safety of the workman and equipment at the working face. The subject of this paper cannot be treated properly unless what is said here is based upon the broad and fundamental problem of genera' roof control. The suc-cessful solution of a problem arising in any industry must have its origin in a complete analysis of the known facts or factors that pertain to it. The several illustrations

Jan 1, 1949

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

Safety and health are no longer secondary responsibilities but must be of paramount concern to every mining operation, according to Anthony J. Thompson, an attorney with Hamel, Park, McCabe & Saunders of Washington D.C. The Mine Safety and Health Administration (MSHA) forecasts an estimated 19,000 inspections during 1979, and the economic and psychological impact of these inspections may he significant. To illustrate his point Thompson reviewed the experiences of a relatively large operation during a recent MSHA visit. The inspector was on the premises for two months, issuing between 250 to 300 "significant and substantial" (s&s) citations. During the most intensive period, about one month in duration, the operation experienced a production loss estimated between 2500 to 3000 tons; an accident rate up 30% over the previous month and 20% over the same month in the preceding year; 100% of the safety director's and safety engi¬neer's time was devoted to the inspection; 50% of top level management's time; and 90% of the mid-level or front line supervisory's time.

Jan 11, 1979

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

Discussion of the paper of K. Huessener, (Trans., vol. 53, pp. 402 to 4333, and of the papers of Linn Bradley, H. D. EGbert and W. W. Strong, pp. 303, 319. R. J. WysoR, So. Bethlehem, Pa. (communication to the Secretary*). —At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been overemphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100" F. In many plants, there is a notable operating economy in using furnace cooling water, which is appreciably warmer than the supply water. However, in a given type of washer, other conditions being constant, the lower the exit gas temperature the lower will be the dust content; this is equivalent to saying that the more washing water is used, other conditions being constant, the lower will be the dust content of the exit gas. For each type of washer there is a certain desired average temperature difference between inlet water and exit gas, concomitant with known average dust and moisture contents, and with economical operation. With the present tendency toward smaller stove checkers, it is generally agreed that gas for stove use should be cleaned to a dust content of 0.20 grain or less. The method employed and extent of gas cleaning are clearly problems for individual furnace plants. As a general proposition, wet washing is decidedly more attractive for furnaces smelting soft, fine Lake ores than for those reducing chiefly hard, lumpy ores, such as the foreign and domestic magnetites. In the former case the average moisture content of the gas is probably 35 grains per cubic foot, the dust content is relatively high and the top temperature relatively low. In our plant, the ore mixtures consist almost exclusively of hard magnetites. The average dust content of the gas leaving the dust catcher will average only about 2 grains and the moisture about 12 grains per cubic foot, corresponding to saturation at about 83" F. The temperature is fully 100" F. higher

Jan 1, 1917

By Lawrence Addicks

(San Francisco Meeting, September, 1915) THROUGH the courtesy of Dr. James Douglas I am permitted to give, a summary of some of the results obtained in leaching slimes tailings in a series of experiments conducted under my direction at Douglas, Ariz.. during the past year. While the test run for which the data are given deals with a particular case, much of the work is general in its application and may therefore be of interest. This work was done upon the ores of the Burro Mountain Copper Co. A description of the geology of the district will be-found in the paper by R. E. Somers published in the May, 1915, Bulletin of the Institute. The mineral is pyrite and chalcocite very finely disseminated throughout the gangue and a characteristic of all the ores is the large amount of alumina present. A representative analysis of the particular ore under consideration would be about as follows: Cu, per cent 2.35 S, percent 3.0 Ag, ounces per ton 0.05 CaO, per cent 0.5 Au None K202, per cent 4.0 Fe, per cent 1.5 SiO2, per cent 70.0 A120,, per cent 13.0 The leaching of the ore direct was early dismissed from consideration for the following reasons: 1. The ore would have to be quite finely crushed to liberate the mineral for leaching; concentrating after crushing would cost but a few cents a ton; and a higher total recovery would result from leaching tailings rather than ore. 2. Rough concentration would yield a suitable material for roasting to make sulphur dioxide or sulphuric acid in connection with the leaching scheme. 3. Such a program put the question of cost vs. recovery on a basis where flotation and discarding of tailings were directly comparable.

Jan 8, 1915

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

By L. S. Cates

THE war is now behind us. We in the mining industry feel a just pride in the part that our industry and our men and our products played in defeating the enemy on the fighting fronts around the world. In five years of mobilization and actual combat, our mines and oil wells produced over 3 billion tons of coal, a billion tons of petroleum, 500 million tons of iron ore, 21/4 million tons of lead, 31/2 million tons of zinc, 5 million tons of copper, 14 million tons of bauxite, 17 million tons of sulphur, 68 million tons of salt, and 3 million tons of potash. It was an unparalleled performance. But what of today? Why the present low production and high costs? Among the black clouds in the mining sky none are so black as that presented by the labor situation. We know it is the result of the legislation and the interpretation of that legislation in the past ten or fifteen years. Since the passage of the Norris-LaGuardia Act in 1932, we have had nothing but a succession of laws, regulations, and decisions that have intensified the strength of the unions and made the operators of the mines and the sources of their financing prartirally impotent

Jan 1, 1946

J. S. Unger,* Pittsburgh, Pa. (written discussion?).-I heartily agree with the author's suggestion, near the close of the paper, that greater uniformity in the making and use of brick is desirable. The effect of the manner of laying the brick, the mortar or cement used, the necessity of standardizing the shapes, the elimination of irregular or poorly designed brick, and the necessity for uniform operating conditions were pointed out by me some years ago. Many factors influence the quality of firebricks. The following figures obtained from bricks during their making or after completion show the need for greater uniformity in their quality. These results were obtained from regular commercial bricks, shipped to the consumer. In many cases the samples were from the same car load.

Jan 11, 1919

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By Harold E. Rowen

Sintering is accomplished at a temperature of more than 2000°F. For the purpose of this discussion it will be defined as the art of burning a solid fuel with 90 to 95 pct ash content. Think of the problems of combustion involved in keeping a home furnace burning properly with 12 to 20 pct ash in the fuel and remember that the amount of fuel involved in the 5 to 10 pct combustion loss represented by the definition has to be just about right or nothing is going to happen. Our forefathers discovered that many ores containing metals csscntial to the steadily rising standards of living were associated with other minerals, sulfur and arsenic, for example, which had to be removed before ultimate refining. They did this by utilizing the solid fuels they had available-the sulfur or other readily combustible components- to create roasting heat.

Apr 1, 1956

By W. R. Aufricht, E. H. Koepf

The theory, measurement, and application of capillary forces in reservoir rock have been treated ex-tensively in the various petroleum publications.1,2,3,4 These forces are of prime importance in oil production, and data on capillary properties are among the most important tools used in the study of reservoir mechanics. The principal application of measured capillary pressure data by the production and reservoir engineer is in the determination of the initial distribution and mobility of fluids in the reservoir. The distribution refers to the magnitude of the oil and interstitial water saturations under capillary equilibrium conditions and to their variation throughout the reservoir as a result of changes in rock properties and nearness to free water. The magnitude of the water (or oil) saturation, as well as the porosity, is required in volumetric calculations of oil in place. In low permeability reservoirs, where long transition zones are common, the magnitude of the oil content, even below the depth interval where commercial rates of flow of oil can be obtained, must be evaluated since this oil contains energy available to the production of the remainder of the reservoir. The mobility of the water phase is of particular importance in water-flood calculations since mobile water may condemn what would otherwise be a successful water flood. In reservoirs with predominantly small pores, high immobile water contents are possible. Conversely, reservoirs with predominantly large pores may contain mobile water even though the interstitial water contents are relatively low. This presentation reviews the distribution and mobility of interstitial water contents as determined from capillary pressure data and shows typical data for various types of carbonate reservoirs. A discussion of the variations found in different types of carbonate reservoirs is given. DISCUSSION Interpretation of Laboratory Data Fig. 1 is a typical laboratory capillary Pressure curve where water saturation as Per cent of Pore space is plotted vs capillary Pressure (psig) for an air-water system. This par- ticular curve was obtained by measurement on a sample of San Andres dolomite with intergranular-type porosity. The sample studied had a permeability of 10.0 md and a porosity of 18.8 per cent. The capillary pressure-saturation relationship illustrated is an inherent property of the rock (a function of the size and distribution of the pores) and represents the ability of this water-wet rock to retain water against the pressure differential exerted by a non-wetting fluid (oil or gas) to remove it. In the laboratory a known pressure differential is exerted from a pressure source; in the reservoir the pressure differential is controlled by the density difference between the hvdrocarbons and the water. The laboratory capillary pressure values may be converted into terms of equivalent height of water column using known values of reservoir oil and water density and measured or average values of interfacial tension

Jan 1, 1958

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending upon the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product.

Jan 1, 1927

F. G. SMITH, Waterbury, Conn.-I would like to ask whether small amounts of iron give the maximum resistance at a low temperature, and if the large amounts of iron raise the temperature at which the maximum resistance occurs? That is, with a small amount of iron, will a maximum be at, say, 10°? F. E. BASH.-With the small amount of iron, the maximum is at a lower temperature, and with the increase of iron, the maximum increases; it seems to come to a maximum and then decrease; that is, increasing the iron up to a certain value increases the temperature at which there is a maximum of resistance, and any increase of iron beyond that value will start decreasing this temperature. With 2 per cent. of iron, the maximum is lower than for 1.5 per cent. which was the value that we found to be satisfactory. F. L. DRIVER,* Jr., Harrison, N. J.-I would like to ask what chance there is of the instrument companies getting together and deciding on standards for both manganin and constantan? We make both of these alloys in this country and we find that each one of the instrument com-panies who buy these materials require different standards of specific electrical resistance and thermal e.m.f. For instance, some of our cus-tomers require an electrical resistance in manganin or therlo of 240 ohms per circular mil foot and others require it with a specific electrical resist-ance of 270 ohms per circular mil foot. They buy these alloys in relatively small quantities so that it means much extra melting and supervision when making up small quantities for each consumer. If something could be. clone to eliminate this, it would be a benefit to the instrument com-panies, who could secure their material more cheaply, and to the manu-facturers, who would not have to spend so much time and effort in special manufacturing.

Jan 12, 1919

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963