Search Documents

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By Harry M. Mikami

Chromite is the only ore mineral of metallic chromium and chromium compounds and chemicals. Because of this fact, chromite and chrome ore are used synonymously in trade literature. In commercial market quotations, chrome ore is the term commonly used. Chromite per se, because of properties imparted by its chromium content, is used in refractories and in special purpose molding sands for metal casting. There are many other minerals containing some, generally minor, amounts of chromium, but none are commercial sources of the element (Thayer, 1956). Chromium and chromite have many diverse uses that, directly and indirectly, critically affect vast segments of our modern industrial system. Most important are probably the metallurgical applications wherein chromium is a component of heat-, abrasion-, corrosion-and oxidation-resistant and high-strength alloys of many types. Stainless steels are the largest volume category of chrome-bearing alloys. Chromium chemicals are used in leather tanning, in pigments, dyes and mordants, printing, chemical process industries, photography, pharmaceuticals, metal plating, pure chromium metal production, and for many other purposes. Chromite is a necessary constituent in basic refractories indispensable for the production of steel, copper, cement, and glass. Under present conditions, the US and North America, with the possible exception of Cuba, have no commercial ore reserves. There are chromite deposits, as will be described, but they would be used only under highly abnormal conditions if all outside sources were cut off for an extended period. All chromite used in the US is imported from the eastern hemisphere in which are contained the principal world reserves. The main suppliers in 1980 were the Republic of South Africa (43%), the USSR (21% ), the Philippines (12%), Albania (11 %), Turkey (8%), and others (5%). The strategic nature of chromite is obvious. End Uses-Grades and Specifications As noted before, the three principal uses for chromite are metallurgical, refractories, and chemical with a fourth minor use as foundry molding sand. For metallurgical applications chrome ore is first reduced in electric carbon arc furnaces to various types of ferrochromium alloys. There are high, medium, and low carbon ferrochromiums with carbon ranging from 0.01 up to 10%. Chromium itself ranges from 50 to 73 %. Ferrosilicon chromium and ferrochromium-silicon grades have chromium from 33 to 67% and silicon from 3 to about 48%. Since iron is reduced with chromium, the Cr:Fe ratio of the ore will determine the ultimate grade of the ferrochromium whereas carbon and silicon can be controlled during processing. MgO, A12O3, CaO, and excess SiO2, are removed in slag. A small amount of pure chromium metal is prepared by alumino-thermic and electrolytic processes from essentially iron-free chrome components that have been made via the chemical route. The higher grades of ferrochromium with chromium in the 66 to 73% range can only be made from ores with not only high chromium content, but low iron, i.e., high Cr:Fe ratio. These ores, conventionally termed metallurgical grade, have Cr2O3 contents of 45 to 56% with Cr: Fe ratios of 2.5 to 4.3. A standard composition is generally 48% Cr2O3 and 3:1 Cr:Fe ratio. Very high grade ores are often blended with lower grades even with the high iron chemical grade. For some ferrochromiums, additions of high alumina refractory grade are used as slag conditioners to facilitate smelting while still contributing chromium values. A lower grade ferrochromium, the high carbon charge chrome, has become the predominant grade in use today for making chromium-bearing steel alloys. This

Jan 1, 1983

By F. J. Budin

Steel supports are increasingly used in metal mines for junctions, chambers, and other wide openings and for semi-permanent areas such as haulageways, shaft stations, and pump rooms. Steel lasts longer-especially in wet mines and where foul air is present-and is procurable in different sizes that will carry heavier loads than any timber of equivalent cross section. The chief advantage of steel supports is that less excavation is needed than with timber support of the same strength, so that faster progress can be made. Since there is no possible way to calculate the exact weight on supports, sizes must be chosen by experience. Any adjustment and cutting of steel supports underground would be costly and time-consuming, and it is therefore advisable to cut sets beforehand at the surface workshops. This requires standardization of sets. All these problems have been recognized at Bawdwin Mines, Burma, where mining is difficult, slow, and very expensive. The lead-silver ore is very brittle, with hanging and footwall rock of unconsolidated rhyolite tuff. During the rainy season from May to October water penetrates into the mine, and where soft rock is present disintegration into a loose mass around openings can be expected. For this reason heavy 10x10-in. timber caps break quickly in drifts and crosscuts, and timber rots in a very short time. An average increase of 50 pct in both maintenance work and costs could not be avoided.

Jan 3, 1960

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By W. N. Roberts

Hadfielcl steel has been studied by transmission electron microscopy to determine the microsl.rtic-ture of the cold-worked material, which has been a subject of controversy for many years. The presence of fcc deformation twins in specimens deformed in tension, by hamnzering, and by explosive -shock loading at room temperature lzas been established by electron diffraction. No evidence of a mar tensite was detected in any of the speciwens. Small amounts of E martensite were idenLified in the hamnleved specimens. DESPITE numerous researches on Hadfield steel since its discovery in 1882, there is still disagreement on the nature of transformations in the cold-worked material. Collette el al.,' using X-ray and electron diffraction, have found evidence for stacking faults, E martensite, and a martensite in Hadfield steel deformed in tension at room temperature. Nishiyama and Simizu,' using electron microscopy, have found stacking faults and E martensite in hammered Hadfield steel. White and Honeycombe have concluded from X-ray diffraction that Hadfield steel remains fully austenitic even after severe cold work at -196 Previous work by the author, indicating the presence of a, martensite in deformed Hadfield steel, was in error due to a faulty interpretation of the electron-diffraction patterns. Various workers,5'7 over the years, have speculated on the presence of deformation twins in Hadfield steel, largely from such circumstantial evidence as the persistence of slip bands with repeated polishing and etching, the presence of serrations in the stress-strain curve, and the absence of evidence of a martensite by X-ray measurements. The advent of electron-transmission microscopy and se- lected-area diffraction has made possible the positive identification of fine deformation twinning. PROCEDURE For tensile tests, standard ASTM specimens of 2-in. gage length, ground from 0.12-in. Hadfield steel sheet, were solution-treated at 1050°C for 30 min in a salt bath, to avoid decarburization, and water-quenched. The grain size was about 0.01 sq mm. Chemical analysis of the steel after heat

Jan 1, 1964

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during. the period May 10 to June 10, 1915: Robert M. Keeney, Somersville, Conn. C. A. Moffett, Birmingham, Ala. Emilio Mosonyi, San Salvador, C. A: A. W. G. Wilson, Ottawa, Canada. Junjiro Nagazumi, Fukuoka, Japan. G. H. Glover, Jr., Short Hills, N. J. Francis R. Pyne, Elizabeth, N. J. R. W. Brock, Vancouver, B. C. F. C. Alsdorf, Los Angeles, Cal. J. L. W. Birkinbine, Philadelphia, Pa. W. J. Loring, London, England. Roy H. Allen, Jamesburg, N. J. R. A. Bull, Granite City; 111. Francis Andrew Thomson received the degree of Master of Science from the Colorado School of Mines at the recent commencement exercises. The subject of his thesis was Stamp Milling and Cyaniding.

Jan 7, 1915

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By D. A. Stevenson, T. Alden, J. Wulff

A portion of the liquidus curve has been determined for the binary alloy systems Ni-Pb and Cr-Pb. The solubility of nickel is 0.53 atomic pet at 372° and 18.63 atomic pet at 1200°C. Chromium shows low solubility, 0.634 atomic pet at 1210°C. Molybdenum and tungsten were also studied and found insoluble in lead, less than 0.005 atomic pet at 1200°C. INCREASED use of liquid metals of low melting X point for heat transfer, coating, joining, and other purposes has renewed interest in the solubility of structural metals in these liquids. A study of Hansen1 and current literature indicates that few liquidus curves at the low melting end of the binary diagrams have been accurately delineated. This statement applies particularly to the binaries of lead. The present paper is limited to nickel, chromium, tungsten, and molybdenum in lead. In early studies2, 3 of the lead end of the Pb-Ni system, a monotectic at 1340°C was established. Tammann and Oelsen' determined the solid solubility of nickel in lead at 20°C to be 0.023 wt pet. Recently Pelzel5 determined the liquidus curve from the eutectic temperature of 327° up to 727°C using a segregation method. In the present paper this part of the curve has been checked and extended to 1244°C. The Pb-Cr system was first studied by Hindrichs.6 He pointed out the existence of a monotectic at 1470°C and indicated a tentative liquidus. Recent corrosion studies of Fe-Cr alloys in lead suggest that chromium is more soluble than iron in lead.7-8 The solubility of tungsten in lead according to Inouye8 is about 30 wt pet at 1200°C. Appreciable solubility of molybdenum in lead might therefore be expected. Experimental Various experimental techniques have been employed in the determination of solubility in liquid metals. For low solubility, thermal analysis is unsatisfactory. A segregation method was used by Pelzel3 in his study of the Pb-Ni system. In this procedure separation of liquid and solid is possible due to difference in density. In the technique of Kleppa10 a single piece of material is maintained in contact with the liquid metal in evacuated Vycor vials. After equilibration, solid and liquid are separated by tilting. Keck and Broder" measured the weight of a piece of the solid solute before and after immersion in a pure solvent bath; the weight loss was a measure of the solubility. All of the above procedures are time-consuming since they permit only one determination per run. Numerous samples for analysis may be taken from the melt in the method described by Gurinsky and CO-workers.10 The rate of extraction of samples is limited only by the time required for equilibration. In the present work, a modification of this method was employed. A 150-g charge of analytical reagent grade lead and the added metal* were contained in an Alun- dum crucible. It rested on firiely divided silica at the closed end of a 45 mm Vycor tube, 500 mm long. The top of the tube was provided with an inlet and

Jan 1, 1959

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg's stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg's phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By F. A. Crossley

The key to disagreements between Blackburn's findings and mine is the word equilibrium". My work attempted to define the equilibrium diagram of the titanium-rich end of the Ti-A1 system. It can readily be shown that Blackburn's conclusions are based primarily on the examination of structures substantially removed from equilibrium. The diagram presented in Fig. 16 is properly labeled a "phase diagram". However, it appears that Blackburn either does not understand or does not accept the difference between "phase diagram" and "equilibrium diagram" as defined in the Metals Handbook.17 The conflict lies not in Blackburn's data but in his interpretation of it, and his use of "transformation", "phase diagram", and "equilibrium diagram" as synonymous terms. I share his view that the light microscope is much inferior to the transmission electron microscope for the study of transformations; but this fact does not render the light microscope useless or untrustworthy. The difficulties experienced with the Ti-A1 system have not been due to the limitations of the light microscope, but rather to the extreme sluggishness in achieving equilibrium at temperatures below 1000° C. Were it not for the light microscope employed with polarized light, the twin phase syndrome' might still be unrecognized and, as a consequence, still adding to the confusion of Ti-A1 investigations. (Ref. 1 should read ... Contract No. N161-25952 ... vol. 236.) Other, more sophisticated techniques, including electron transmission, simply confirm the erroneous tentative conclusions drawn from observations of structures due to the twin-phase syndrome. By the standards of most of the investigations of the Ti-A1 systems, seven of the fifteen compositions investigated by Blackburn were seriously contaminated with oxygen. The writer has found that 0.1 wt pct 0 shifts the a + Ti3A1 boundary to 1 at. pct lower A1 content at 700°C. At constant aluminum content, this corresponds to a temperature shift of the boundary of +25°c.18 Blackburn advises that the first group of alloys contained 0.1 to 0.15 wt pct 0, bur he does say whether the analyses were performed on as-received material or on specimens in their final state of heat treatment. This is especially important considering the 20-mil-thick starting materials. If specimens had been annealed in the two-phase a + 6 region it would have provided an indication of the final degree of oxygen contamination since up to about 12 at. pct A1 the boundaries of this region are well-defined for low-oxygen alloys. Blackburn questions the capability of light microscopy in determining phase boundaries in the Ti-A1 system. I submit that the a/a + Ti3A1 boundary in Fig. 1 of Ref. 1 over the composition range from 10 to 18 at. pct A1 was determined by dilatometry and supported by electron diffraction. Specimens of alloys containing 8, 10, 12, and 14 at. pct A1 were aged at 550°C for 1000 hr (under stress of 5000 psi to accelerate the tendency to equilibrium) and then fractured in tension at room temperature. Collodion was applied to the as-fractured (unetched) surface and, when stripped, carried away particles identified by electron diffraction as Ti3A1. Perhaps Blackburn will explain why these electron diffraction data were ignored. At this time, a technique for revealing or indicating

Jan 1, 1969

By L. T. Sicka, H. N. Thomson

The Tooele plant of the Internationa1 Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. The copper plant has been in operation since July, 1910, arid the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 1, 1914

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941