Search Documents

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By R. D. Barer, M. B. Bever

Age hardening alloys are quenched from the solution treatment to room temperature in order to retain a supersaturated solid solution. Some alloys age "naturally" in this condition but in most alloys aging is induced "artificially" by heating to intermediate temperatures. Cold working of the supersaturated solid solution accelerates the aging process and quenching strains have the same effect. The investigation reported here is a study of the progress of aging in specimens quenched directly from the solution treatment to various aging temperatures. This procedure reduces the temperature interval of quenching and the resulting quenching stresses. It also eliminates any changes which would take place in the undercooled sample at room temperature prior to aging at an elevated temperature. Isothermal aging is thus approached and its kinetics may be studied. An aluminum-copper and an aluminum-silicon alloy were chosen for this investigation. The aging mechanism of aluminum-copper alloys is complex while the aging of aluminum-silicon alloys is nearly ideal. As standards of comparison for the samples directly quenched to the aging temperature, specimens were also age hardened by the usual procedure in which solution treated samples are first quenched to room temperature and then reheated to the aging temperature. Review of Previous Work The mechanism of age hardening has been the subject of a controversy which has ranged from the theory of outright precipitation of an equilibrium phase to theories based on subtle changes occurring in the matrix prior to precipitation. A detailed critical review of the literature up to 1939 is available1 and contributions to the general theory of age hardening continue to be made.2,3 Age hardening, whatever its mechanism, involves the nucleation of a second phase within a supersaturated solid solution. Theoretical considerations4,5 indicate that the rate of nucleation reaches a maximum at an intermediate temperature below the temperature at which supersaturation sets in. Studies of precipitation at various subcritical temperatures have demonstrated that the largest property changes in a given time occur at such intermediate temperatures.6,7,8 The precipitation of a phase from supersaturated solid solution is accelerated by strains which may result from quenching or cold work. Phillips and Brick9 established that quenching strains are an essential condition for the age hardening of aluminum-copper alloys at room temperature, at least for aging periods of less than 30 days. They also found that on aging at 300°C the hardness increased faster and reached a higher maximum after quenching into water than after quenching directly to the aging temperatures. Fink and Smith10 observed preferential precipitation on slip bands and grain boundaries in aluminum-

Jan 1, 1950

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By James Aston

THREE years ago the writer presented a paper on the trend of development in the wrought iron industry,1 wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. A Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences.

Jan 1, 1929

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult's law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman' equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,' Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell's value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1' has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By C. A. Zapffe

BOTH the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. BLEEDING, RISING, AND PIPING The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinction between bleeding and rising in reference to killed metal.* POROSITY Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth1 noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel-oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1942

By B. M. Larsen, W. E. Shenk, T. E. Brower

Shortly after our previous paper on this subject was printed1 we located a source of uncertainty in the results arising from the unexpected fact that hydrogen slowly reduces silica at 1100" C. in presence of iron, even when the iron nowhere touches the silica, although in absence of iron it does not do so. This difficulty has been completely obviated by the use of a small high-frequency furnace, which enables us to heat the specimen for analysis without raising the temperature of the silica vessel to a point at which any appreciable reduction of the silica glass occurs. We now describe this modification of procedure, and present some typical results obtained with it. For any given specimen of steel, the results are entirely definite and reproducible, but their precise significance is still open to some question, as indeed is true of all methods of oxygen determination SO far developed. Further elucidation of this question is to be expected from the cooperative comparison of the several methods now under way under the auspices of the Bureau of Standards at the instance of the Iron and Steel Division of the A.I.M.E. Apparatus The final form of apparatus we have used is identical with that described and illustrated in our previous paper, except for the substitution for the Globar furnace of a small high-frequency furnace actuated by a vacuum tube oscillator2 0f about 1.5 kw. capacity, and for a slight modification of the containing vessel. This transparent silica vessel is illustrated in Fig. 1 of this paper. Its enlarged portion is about 5 cm. in diameter and 13 cm. long. The silica tube for inlet of hydrogen is fused into this bulb and ends beneath the metal "bucket" holding the steel sample. This sample is in the form of fine millings. The "bucket" is suspended by a platinum wire from the cap of Pyrex glass. The high-frequency

Jan 1, 1934

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and ('Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By L. C. Michels, O. G. Ricketts

The disorientations between s?nall grains, whose growth has been arrested at an early stage of recrys-tallization, and the deformed matrix in cold-rolled aluminum single crystals were determined using transmission Kikuchi line and electron diffraction patterns. The orientations of the recrystallized grains were found to be random, and the disorientations of these grains with the matrix weve found to be intermediate to large. This leads to the conclusion that the observed vecrystallization began in small areas of large disorientation present in the cold-worked structure. heavily cold-worked thin sections of aluminunz single crystals and of polycrystalline aluminum and nickel were produced directly by a mechanical technique. The specinlens thus prepared were heated with the electron beam to bring about vecrystallization during observation in the electron microscope. Motion pictures taken du.ring heating and the electvon, microg.raphs taken both before and aftev heating allowed the recrystallization process to be traced to its ovigin. Re cvystallized grains originated in very s,mall regions of the cold-worked structure and developed through rapid migration of high-angle boundaries. The boundaries either were present as such in the matrix or were formed out of dense dislocation networks. SIGNIFICANT advances have been made in recent years in the study of nucleation of recrystallization using the technique of transmission electron microscopy of thin metal foils. Bollman1 in a study of heavily rolled polycrystalline nickel found support for the Cahn-Cottrell2,3 theory of nucleation. According to this theory nuclei form by the initially slow growth of subgrains formed through polygonization. During this initial period of slow growth (the incubation period) the migrating boundary of the subgrain increases its disorientation with the cold-worked matrix and thereby increases its mobility to become a rapidly migrating high-angle boundary. Bailey4,5 investigated the annealing behavior of several metals deformed both in tension and by rolling and concluded that recrystallization took place through the migration of high-angle boundaries. With low deformations these boundaries were present in the metal before deformation. With high deformation it was not possible to tell whether the boundaries were pieces of the original grain boundaries or were produced either during deformation or by polygonization during ameal- ing. Direct observation during heating of metal foils indicated that subgrains form by polygonization and grow at an uneven rate. The grain size obtained decreased with decreasing foil thickness indicating that the foil surface resists boundary motion. Votava,6 in heating stage experiments on rolled copper, observed nuclei to appear suddenly and grow in jumps of differing magnitude. However, he found no special dislocation configurations where the nuclei appeared. Fujita,7 as a result of a study of subgrain growth in heavily worked aluminum, concluded that the boundary of a recrystallized grain initially forms from the boundary of a group of subgrains. This occurred by a process of deposition of vacancies and dislocations in the group boundary as the boundaries within the group disappear. HU8,9 directly observed a similar process in heating stage experiments on 70 pct rolled Si-Fe single crystals. The growth of subgrains appeared to proceed by a coalescence mechanism. The observed fading away of the boundary between two subgrains was explained by the moving out of dislocations from the disappearing boundary into the connecting or intersecting boundaries around the subgrains. The subgrain size and degree of disorientation with the surrounding structure were thus increased. With the increase in disorientation occurred a corresponding increase in boundary mobility, which eventually allowed the boundary to migrate rapidly. This process was observed to occur within "microbands" consisting of parallel narrow segments disoriented by a few degrees present in the as-rolled structure. The conclusion of Rzepski and Montuelle10 that growth is preceded by the coalescence of blocks through disappearance of their common boundaries supports this view. In contrast to Hu's coalescence model for nucleation were the conclusions of Walter and ~och.""~ Working with the same material as Hu, of the same orientation and rolled to the same reduction, they concluded that nucleation occurred by the Cahn-Cottrell mechanism. They observed, in agreement with Hu, that recrystallization began in the "microband" regions which they referred to as "transition" bands. Bartuska13 studied subgrain growth in heavily rolled nickel using a beam heating method in the electron microscope. He concluded that nuclei for recrystallization form from the largest most perfect subgrains present in the cold-worked structure by rapid intermittent migration of parts of subboundaries. In rare instances he observed subgrain growth by coalescence. EXPERIMENTAL PROCEDURE The materials used in this study were 99.999 pct A1 supplied by A.I.A.G. Metals, Inc., and 99.999 pct Ni supplied by Johnson and Matthey and Co., Ltd. The Hitachi HU-11 electron microscope, with uniaxial

Jan 1, 1968

By John Naughton

At the General Electric ResearchLabora-tories, we have been interested in the iron-manganese system and the effect of hydrogen on the properties of these alloys. Dr. H. H. Uhlig previously has presented some of these results.' We wish now to offer some other of the data that have a bearing on the subject of this symposium. In the determination of hydrogen in the iron-manganese system by any heating Method we are presented with the problem of the evaporation of volatile manganese and the consequent adsorption of hydrogen by this evaporated metal. It seems wise. therefore, to extract gas at as low a temperature as feasible. Consequently we chose the vacuum or hot extraction method for the analyses of these alloys. The apparatus used is shown in Fig. I. The design is a modification of the apparatus described by Holm and Thompson. To limit loss of hydrogen, samples are stored in a chamber immersed in liquid air. We recommend this procedure whenever there is a question of loss of hydrogen at room temperature. Thence they are moved to the quartz furnace by means of a small magnet, where they are heated by induction to 700' to 800°C. The extracted gas is removed by the circulating pump and placed in the known volume VI (or V2). The circulating pump has been described.3 It is so designed that in spite of the fact that the outlet portion of the pump is part of the known volume, this volume is affected neither by the speed of pumping nor by the pressure of stored gas. The pump also serves to circulate the gases for analysis. The analytical system consists of a

Jan 1, 1945

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By D. A. Stevenson, T. Alden, J. Wulff

A portion of the liquidus curve has been determined for the binary alloy systems Ni-Pb and Cr-Pb. The solubility of nickel is 0.53 atomic pet at 372° and 18.63 atomic pet at 1200°C. Chromium shows low solubility, 0.634 atomic pet at 1210°C. Molybdenum and tungsten were also studied and found insoluble in lead, less than 0.005 atomic pet at 1200°C. INCREASED use of liquid metals of low melting X point for heat transfer, coating, joining, and other purposes has renewed interest in the solubility of structural metals in these liquids. A study of Hansen1 and current literature indicates that few liquidus curves at the low melting end of the binary diagrams have been accurately delineated. This statement applies particularly to the binaries of lead. The present paper is limited to nickel, chromium, tungsten, and molybdenum in lead. In early studies2, 3 of the lead end of the Pb-Ni system, a monotectic at 1340°C was established. Tammann and Oelsen' determined the solid solubility of nickel in lead at 20°C to be 0.023 wt pet. Recently Pelzel5 determined the liquidus curve from the eutectic temperature of 327° up to 727°C using a segregation method. In the present paper this part of the curve has been checked and extended to 1244°C. The Pb-Cr system was first studied by Hindrichs.6 He pointed out the existence of a monotectic at 1470°C and indicated a tentative liquidus. Recent corrosion studies of Fe-Cr alloys in lead suggest that chromium is more soluble than iron in lead.7-8 The solubility of tungsten in lead according to Inouye8 is about 30 wt pet at 1200°C. Appreciable solubility of molybdenum in lead might therefore be expected. Experimental Various experimental techniques have been employed in the determination of solubility in liquid metals. For low solubility, thermal analysis is unsatisfactory. A segregation method was used by Pelzel3 in his study of the Pb-Ni system. In this procedure separation of liquid and solid is possible due to difference in density. In the technique of Kleppa10 a single piece of material is maintained in contact with the liquid metal in evacuated Vycor vials. After equilibration, solid and liquid are separated by tilting. Keck and Broder" measured the weight of a piece of the solid solute before and after immersion in a pure solvent bath; the weight loss was a measure of the solubility. All of the above procedures are time-consuming since they permit only one determination per run. Numerous samples for analysis may be taken from the melt in the method described by Gurinsky and CO-workers.10 The rate of extraction of samples is limited only by the time required for equilibration. In the present work, a modification of this method was employed. A 150-g charge of analytical reagent grade lead and the added metal* were contained in an Alun- dum crucible. It rested on firiely divided silica at the closed end of a 45 mm Vycor tube, 500 mm long. The top of the tube was provided with an inlet and

Jan 1, 1959

By A. F. Bertuzzi, M. R. Tek, F. H. Poettmann

A method is presented for predicting pressure drop for two-phase fluid flow in horizontal pipes. A set of 267 experimental measurements randomly sampled from approximately 1,000 measurements from various literature sources was used. Pressure gradients calculated by the procedure developed and compared with the experimental values showed a bias of +0.82 per cent and a standard deviation of 20.8 per cent. The advantatges of this method over other available methods of predicting two-phase flow pressure drop are (a) its comparative simplicity of application, (b) its relative independence of flow patterns, (c) its accuracy, which on the basis of a statistical evaluation predicts pressure drop closer than other available methods, and, (d) its ability to satisfactorily correlate laboratory data from various sources while the correlations from these sources do not appear to agree with one another. The method has been reduced to a simplified graphical procedure, suitable for field use. A two-phase f factor is defined and correlated with parameters involving the flowing gas-liquid mass ratio, a Reynolds number for the gas phase, and a Reynolds number for the liquid phase. The choice of parameters allows the correlation to reduce to the usual f factor plot for the limiting conditions of (111 gas or all liquid. INTRODUCTION The mechanics and characteristics of two-phase flow systems have been of interest throughout the industry for some time. In numerous engineering installations such as pipe lines, chemical reactors, and heat exchangers, two-phase flow conditions are of every day occurrence. In oil production operations it has been desirable, in some cases, to consider transporting gas and oil together in a common pipe from oil field to process plant. The trend toward centrally located stock tank batteries in oil fields has resulted in longer gathering pipelines in which more than one fluid phase is flowing. The increase in the producing capacity of oil wells due to new production tech- niques has created the need for review and re-design of many surface gathering lines for properly handling the increased production. Optimum pipe size for the situations described above has become an important factor. The problem which is of interest here involves the ability to predict the relationship between pressure drop, fluid properties, fluid rates, pipe diameter, and pipe length. Although the literature1,5,10,13,18,19 contains various articles dealing with specific cases of the problem, Lock-hart and Martinelli17 proposed the most general solution. Their method has been later modified by Baker:1 Alves2 demonstrated that different flow patterns are possible for a flow mechanism defined by Martinelli such as gas turbulent, liquid turbulent. Baker explained deviations experienced with Martinelli's correlations on the basis that different flow patterns could exist for the same flow mechanism. Using Martinelli's method of correlatioil, Baker correlated data for each flow pattern for the turbulent-turbulent flow mechanism. Bergelin and Gazley6,7 presented a correlation for predicting gas phase

Jan 1, 1957

By William H. Bassett

COPPER is the world's most important non-ferrous metal, and brass is the most widely used non- ferrous alloy. Much of the utility of each may be credited to the work of metallurgists who have constantly improved the quality of the metals and alloys and the methods of fabrication. Standing in the front rank among these is William Hastings Bassett, the newly elected president of the Institute. Mr. Bassett, ,who is technical superintendent and metallurgist for the American Brass Co.,

Jan 1, 1930

By John C. Holtz

Hostility is a characteristic of the environment in underground mines. Nature opposes man's efforts to remove mineral deposits, and this condition is recognized when mining is described as winning minerals from the earth. Evidence of this conflict is the action of natural forces to close excavated passageways. In many mines, this behavior of the surrounding environment is an ever-present and ever-changing problem despite much research and empirical study. Geological conditions change abruptly and may result in rock bursts, the inrush of water, or variations in rock hardness. Although aspects of these problems will become intensified as the rate of mining increases, they are not considered in this discussion. Emphasis herein will be on the changes in the atmospheric environment. Men underground work in an ever-changing, alien, ambient atmosphere. Many conditions are encountered that will affect their health and safety unless properly controlled. Potentially explosive gases are released from minerals as they are mined or enter from the surrounding earth. Some mining methods generate noxious gases. Natural processes and diesel equipment can steal life-sustaining oxygen. Airborne dust may cause lung diseases when breathed by miners in excessive amounts and by affecting visibility, introduce safety hazards. Deep mines pose heat problems that may be aggravated by high-speed mining. The deleterious effects caused by these changes, and their mitigation, are subjects of this discussion. THE UNDERGROUND ATMOSPHERE Health and safety problems from changes in the underground atmosphere have been apparent since the beginning of mining. Alleviation of these problems has been by ventilation with normal air from the earth's surface that flushes away the vitiated mine atmosphere. The objective is to provide atmospheric conditions essentially similar to those that man is accustomed to on the surface.

Jan 1, 1970

By W. R. Hamilton

THE knowledge of the existence of petroleum in Southern California dates back to the days of the missions. The presence of asphaltum and semisolid bitumen was reported at Santa Barbara in 1792, but no serious attempt was made to develop oil until Professor Silliman's optimistic report in 1865 started California's first oil boom. Wells were drilled in many counties of the State, but the equipment was unsuitable and the drilling difficult and no production was obtained except in Ventura County. Even there the production was of little importance commercially, and not until the early '80s did it become sufficient to again attract attention. In 1888 the production for the State had reached a total of about 700,000 bbl. per year, practically all light oil produced in Ventura County, Pico Canyon, Los Angeles County and in the Puente Hills. The production of petroleum attained the dignity of an industry in 1895 when the Los Angeles City and Coalinga fields were discovered. The subsequent development has been remarkable, and in 20 years the production has increased from 1,000,000 to 100,000,000 bbl. per year. The refining industry has kept pace with the production of oil. The Pacific Coast Oil Co., the predecessor of the Standard Oil Co. of California, was the virtual pioneer refining company of the State, having built a refinery at Alameda about 1880. When purchased by the Standard, about 1902, it was dismantled and the refinery at Point Richmond was built. The Richmond refinery is now one of the largest in the world, having a capacity in excess of 60,000 bbl. per day. A small refinery was built by the Union Oil Co. at Santa Paula in the early days of the industry and later many asphalt refineries were in operation in Southern California. The Pacific Coast Oil Co. was then, as has been its successor, the Standard Oil Co. of California, the principal refiner and marketer of light products, the most valuable of which was kerosene.

Jan 6, 1916