Search Documents

By Nicholas T. Camicia

Coal is one of our oldest known commodities. Historic evidence indicates that this fossil-formed fuel was used in China and in Wales some 3000 to 4000 pears ago. Coal was discovered in North America in 1679 by French explorers in northern Illinois, and in 1700 a colony of Huguenots came across bituminous coal in Virginia. One might think by this long history of a single commodity that the string was about played out. Quite the contrary, coal is in greater demand than ever before and coal mining today is a modern industry. It is in an unprecedented growth period as the nation-and the world-demands more and more energy coincident with dwindling reserves of other fossil fuels. By the year 2000 the demand for coal is expected to at least double the current level of some 600 million tons annually despite the advent of nuclear power. To meet this challenge, the coal industry is vitally in need of an increasing supply of technically trained and progressive manpower. And, coupled with a serious shortage of engineers and technicians, it represents a rich vein of occupation opportunities-all the way up to top career levels. Today, coal mining is a complex, highly specialized industry concerned with more than just getting coal from the earth and putting it into the furnaces of the consumer. The industry is concerned with the environment, with maintaining a viable ecology. Recognizing the ramifications of global economics, the industry is very much aware of its important position in contributing to a constantly rising standard of living throughout the world. The key to rewarding employment in the coal industry is skill-skill that has been developed by education, training, and experience. None of these alone is enough; all three are necessary today to produce the skill needed to meet the employment requirements of the coal industry. Routine manual labor will no longer do the job in coal mining. In the United States coal mining has been mechanized to a degree unsurpassed anywhere else in the world, and the coal worker must be thoroughly

Jan 1, 1973

By R. M. Keeney

Jan 1, 1915

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By G. W. Traer

THE distillation of bituminous coals at what is commonly termed low temperature, and the quantities, nature and adaptabilities of the products have been the subject of considerable experimentation, during recent years. Fortunately, the earlier work in this country was done by men whose scientific training qualified them properly to record and interpret the results of-their experiments. The work of Prof. Parr, of the University of Illinois, is especially notable in this respect. Prof. Parr's work, added to that of English experimenters, demonstrated certain things to a degree which is generally regarded as convincing. They have proved that a caking bituminous coal, when subjected to a temperature of not more than 1000° F. (preferably somewhat less) will yield light tar having low specific gravity (about 1.06) and high value; also, that this yield, with a given coal, will depend upon the percentage of hydrocarbons in the coal, the maximum temperature used, and the promptness with which the distillate gases are removed. It is assumed that air is excluded from the retort, and that the coal is subjected to heat for a sufficient time to drive off all of the tarry hydrocarbons. The results attained in the first, or low-temperature stage of the Carbocoal process, recently described by C. T. Malcolmson, corroborate these general principles. It is the purpose of the writer to describe other work of a practical nature, directed toward the commercial adaptation of these principles, which was begun nearly two years ago; this investigation was assisted by A. J. Sayers, of the Link-Belt Co., and Carl Scholz.

Jan 9, 1918

By J. H. Swisher

The rate of internal sulfidation of austenitic Fe-Ti alloys in H2S-H2 gas mixtures is controlled primarily by sulfur diffusion, with counterdiffusion of titanium playing a minor role. At temperatures below 1100°C, enhanced diffusion along grain boundaries becomes important. The rate of internal sulfidation at 1300°C is approximately equal to the rate computed from the sulfur diffusion coefficient. The diffusion coefficient of titanium in y iron has been determined from electron microprobe traces in the base alloy near the subscale interface. The solubility of sulfur in Fe-Ti alloys has been measured in the temperature range from 1150° to 1300°C. The equilibrium sulfur content is found to increase with titanium content, due to the large effect of titanium on the activity coefficient of sulfur. The Ti-S interaction becomes stronger as the temperature decreases. TITANIUM as an alloying element in stainless steels is an effective scavenger for interstitial impurities, carbon in particular. Titanium is known to form stable sulfides; however extensive thermodynamic data on the Ti-S system are not available. Schindlerova and Buzek1 have shown that the Ti-S interaction in liquid iron is moderately strong. There have been no previous studies of the Ti-S interaction in solid iron. Internal sulfidation of Fe-Mn alloys was the subject of a recent investigation by Herrnstein.2 He found the rate of internal sulfidation to be an order of magnitude greater than predicted from available solubility and diffusivity data. A satisfactory explanation for the discrepancy could not be given. In the present study, the solubility of sulfur in austenitic Fe-Ti alloys was measured using a standard gas equilibration technique. Fe-Ti alloy specimens were also internally sulfidized. The rate of internal sulfidation was measured as a function of temperature and alloy composition. Supplementary electron micro-probe measurements were made to provide additional information on the nature of the internal sulfidation process. EXPERIMENTAL The starting materials were alloys containing 0.12, 0.24, 0.38, and 0.54 wt pct Ti. The alloys were made in an induction furnace by adding titanium to electrolytic iron that previously had been vacuum-carbon-deoxidized. The major impurity in the alloys as determined by chemical analysis was carbon. The carbon content of the alloys averaged about 100 ppm; metallic impurities were presented in concentrations of 50 ppm or less. Specimens were made in the form of flat plates, 0.03 by 2 by 4 cm for the equilibrium measurements and 0.5 by 1.5 by 3 cm for the rate measurements. The experiments were performed in a vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction tube. In the gas train, flow rates of the reacting gases were measured using capillary flow meters. The source of H2S was a mixture of approximately 2 pct H2S in H2, which was obtained in cylinders from the Matheson Co. A chemical analysis was provided with each cylinder. The H2-H2S mixture was diluted with additional hydrogen to obtain the desired ratio of H2S to H2, and the resulting mixture was diluted with 30 pct Ar to minimize thermal segregation of H2S in the furnace. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over Pas. The samples used in the solubility measurements were analyzed for sulfur by combustion and iodometric titration. The subscale thickness in the internally sulfidized samples was measured on a polished cross section, using a microscope with a micrometer stage. Electron microprobe traces for titanium in solution were made on several samples that had been internally sulfidized. A Cambridge microanalyzer was used, and the known titanium content at the center of the specimen was used as a calibration standard. The procedure for the microprobe measurements will be described further when the results are presented. RESULTS AND DISCUSSION Equilibrium Data. Fig. 1 shows the sulfur concentration as a function of gas composition for three alloys equilibrated at 1300°C. The dashed line is based on data published by Turkdogan, Ignatowicz, and pearson3 for pure iron. The breaks in the curves are the saturation points for the alloys. The fact that the initial slope decreases with increasing titanium content indicates that titanium interacts strongly with sulfur in solution. To obtain information on the composition of the precipitating sulfide phase, the measurements described in Fig. 1 were extended to higher sulfur partial pressures. These results are shown in Fig. 2. (The initial portions of the curves are reproduced from Fig. 1.) The highest PH2s /pH2 ratio used is believed to be below the ratio required for the formation of a liquid sulfide phase. Time series experiments were used to study the approach to equilibrium in the samples. It was found that equilibrium with the gas phase was reached in less than 4 hr at 1300°C.

Jan 1, 1969

By Philip Drinker, R. M. Thomson

In the mining and metallurgical industries, numerous problems arise requiring determinations of solid and of liquid particles suspended in air. Frequently, these problems are of local interest and involve purely economic or operating difficulties; on the other hand, toxic effects from the inhalation or the ingestion of substances suspended in air may be a matter of concern. For checking up process improvements or for determining ventilation efficiencies in problems of this general nature, various methods have been proposed. .Although simpler methods are often satisfactory, precipitation combines several desirable features that other methods lack. This paper is, therefore, devoted to a discussion of portable alternating-current precipitators applicable to the quantitat,ive determination and microscopy of dusts, fumes, and smokes in air. Small particles suspended in gases, such as air, are referred to in the literature as aerosols or suspensoids. Of these terms, suspensoids appears to be preferable as being more nearly in keeping with words in everyday use. In problems involving air pollution by small particles—by suspensoids—it is convenient to distinguish three broad classes based on the size, the degree of dispersion, and the method by which the particles become suspended in the air. Dusts.—Particles or aggregates of particles, 150 to 1 micron in diameter, that are thrown into the air by mechanical agencies are termed dusts. Examples are silica; talc; cement; organic dusts such as hard rubber, starch, and cocoa; flocculated fume, and smoke products. Fumes.—Particles, 0.2 to 1 micron in diameter, formed from chemical or physicochemical reactions are known as fumes. Examples are ammonium chloride, lead and mercury, zinc and magnesium oxides, fogs, and acid mists. Smokes.—Particles, less than 0.3 micron in diameter, formed by incomplete combustion of carbonaceous and other substances are called smokes. Examples are the particles formed from burning tobacco, oil, tar, and gas.

Jan 1, 1925

By J. E. Dutrizac, R. J. C. MacDonald, T. R. lngraham

When sintered disks of synthetic chalcopyrite (CuFeS2) were leached in acidified aqueous solutions of ferric sulfate, the following reaction stoichiometry was obtained: CuFeS2 + 2Fe2(SO4)3 = CuSO4 + 5FeSO4 + 2S Over the temperature range from 50º to 94ºC, the reaction displayed parabolic kinetics. The parabolic rate constant for the dissolution of copper is given by the equation: log.k(mg2/cm4-hr)= 11.850 - 3780/T The activation energy for the dissolution process is 17 ± 3 kcal per mole. The parabolic kinetics have been attributed to the progressive thickening of a sulfur film on the surface of the chalcopyrite. When the leaching solutions contain less than 0.01 molar Fe+3 , the Fe concentration influences the rate of leaching, probably through a mechanism involving the diffusion of ferric sulfate through the sulfur layer. At higher Fe+3 concentrations, the rate control in the leaching. reaction has been attributed to the diffusion of ferrous sulfate through the sulfur. The rate of reaction is insensitive to changes in acid concentration and in disk rotation speed. ThE reaction of acidic ferric sulfate solutions with various sulfide minerals is of practical interest for both bacterial and heap leaching. This leaching medium is generally used with low-grade ores that cannot be treated profitably by conventional means. In both bacterial leaching1-3 and heap leaching, the active agent for sulfide dissolution is ferric sulfate. Although the reactions of ferric sulfate with chalcocite, covellite, and bornite have been investigated,4*7 the kinetics of leaching chalcopyrite with ferric sulfate have not been thoroughly studied. This paper reports a study of that reaction. EXPERIMENTAL Reagent-grade sulfur was purified by the method of Bacon and FanelliB and then it was vacuum-distilled to remove any soluble magnesium salts that had been introduced during the purification procedure.9 From stoichiometric quantities of the purified sulfur and hydrogen-reduced electrolytic copper sheet (99.90 pct Cu), CuS was synthesized at 450°C in a vacuum-sealed, pyrex vessel. About 24 hr was required for the completion of the reaction. A similar procedure involving hydrogen-reduced iron wire (99.90 pct Fe) was used to synthesize FeS1.002. A 2-furnace arrangement was required. The iron was heated to 800°C while the sulfur was maintained at about 400°C. Although the reaction to consume the sulfur was rapid, the material required additional heating (1 week) in a sealed silica ampoule at 800°C before it was homogenized. X-ray powder diffraction analysis confirmed that the copper sulfide was covellite and that the iron sulfide was troilite. The composition of the iron mineral was confirmed by wet chemical analysis. The two sulfides were ground to minus 100 mesh, weighed in equimolar amounts, mixed thoroughly, and pressed into pellets at 80,000 psi. The pellets were vacuum-sealed in pyrex ampoules and then sintered for 3 days at 550°C after an initial heating at 450°C for a few hours. The pellets were then cooled, polished with 3/0 emery paper, rinsed in acetone, and stored. The material had the characteristic brassy color of chalcopyrite and was shown by X-ray diffraction to be CuFeS2. Microscopic examination of the polished surfaces revealed small inclusions of pyrite (approximately 0.5 vol pct) as the only impurity. The presence of small amounts of a second iron compound will not alter the amount of dissolved copper but might increase the amount of ferrous ion slightly. It was calculated that dissolution of all of the pyrite and 100 mg of Cu (a typical value) would change the expected ferrous concentration by only 4 pct. Microscopic examination of a pellet after leaching revealed that the pyrite was not preferentially solubilized; only those pyrite grains at the surface were attacked. Hence, the pyrite is unlikely to alter the rate of copper dissolution. The chalcopyrite disks were about 1.7 mm thick and 27 mm in diam. They were about 80 pct of theoretical density, and for this reason their true reaction area was somewhat larger than the 5.8 sq cm area presented by the polished face. The disks were cemented to lucite cylinders in such a way that only the polished face was exposed. The disks were then leached by methods previously described.6,7 RESULTS AND DISCUSSION Stoichiometry and Kinetics. The initial experiments were directed to the problem of resolving the stoichiometry of the leaching reaction. Disks of CuFeS2 were leached at 80°C for various periods of time in acidified ferric sulfate solutions that were protected from oxidation by a cover of flowing nitrogen. When the disks had been partly leached, they were removed, their soluble salts were washed out, and then they were treated with CS2 in a Soxhlet extraction apparatus. The ratio of elemental sulfur to dissolved copper thus obtained was approximately 2 to 1. After the extraction of elemental sulfur from the pellet, the residue consisted of unreacted chalcopyrite only. For runs in which an appreciable amount of copper was dissolved, the ratio of ferrous ion to cupric ion in the solution was

Jan 1, 1970

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

VENTILATION of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 19 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. VENTILATION FOR MECHANICAL LOADING IN GASSY MINES In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to by-pass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity, and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1941

By AIME

AS with Phil Kraft, referred to on this page last month, travel has always held a great fascination for Raymond Frank Baker and for that reason he determined to become a geologist. He had heard that geologists travel and that was what he wanted to do. Now as chief geologist for The Texas Co. his early wish has been fulfilled-he spends almost one third of his time journeying' from one oil field to another. Mr. Baker was born in New Haven, Conn., on Jan. 11, 1892, and went through the public schools in New Britain. A stalwart New Englander, he attended Yale and in 1912 received a degree in civil engineering. For a year following this he worked as a civil engineer for the New York Central Railroad, but his early urge to travel widely could not be satisfied here. So in 1913 he re-entered Yale and until 1916 studied mining and economic geology. He had a little taste of field work, which later became so enjoyable to him, in the summer of 1915 when he worked with the U. S. Geological Survey as a geologic aid. In 1916 he made his first contact with The Texas Co. when he entered their Tulsa office as a geologist. This early career was interrupted by service in the

Jan 1, 1947

By L. C. Glenn

The account of oil and gas production in Tennessee, and of the geological factors related to such production, as given by the writer' a few years ago needs to be supplemented by brief statements as to production and development to bring it up to date. Activity in searching for favorable geological structures or in drilling given areas has never been comparable to the intensive work done in states of large production. It is not possible, therefore, to prepare a statement giving the details that may be readily available in such states, but instead one must be content with more general statements. In the past 10 or 12 years there has been a moderate amount of drilling for both oil and gas widely scattered over the state. Of much of this there is no available record. Morgan, Clay, Scott and Pickett counties have had more oil-drilling activity than any other counties, and likewise they have had almost all of the oil production. In Scott and Morgan counties production centers about Sunbright and Glenmary, the oil coming from the St. Louis limestone at a depth of 1200 to 1500 ft. Wells usually are small but generally hold up well. In Clay, Pickett, Fentress, Overton, Macon and Sumner counties there is a large area in which there are many small structural domes, some of which have been drilled. Wells vary from a few barrels to several hundred flush production and last for some years. The oil comes from porous weathered zones, mostly in the Trenton division of the Ordovician, though some comes from lower horizons beneath one or more bentonite beds that serve as horizon markers and are known as the "pencil cave." Wells recently drilled in the Central Basin and in the Western Highland Rim have been dry or have had only shows of oil. The horizons tested are also usually Ordovician in the Central Basin and usually either Ordovician or Mississippian; occasionally also Devonian on the Highland Rim. In the Gulf Embayment area of West Tennessee there has been but little activity. A well near Ridgely said to be over 2200 ft. deep is supposed to have entered Upper Cretaceous sands and clays in the lower

Jan 1, 1934

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

By Horace Winchell

IT IS OFTEN interesting to look backward and review the world's progress in any line of human endeavor. Our pride is flattered by our achieve-ments and our imagination stimulated by the compari-son between our present productivity and prosperity and those of the relatively unenlightened days of our recent ancestors. We love to reflect on the progress of the last quarter of a century in the art of metallurgy, in. the production and consumption of the various metals and minerals which constitute the basis of our industrial and commercial supremacy. We dwell complacently on the figures which prove that we are the world's leader in nearly all departments of mining and that our production of necessary minerals over-shadows that of other countries. We recall the days when it was considered the proper thing, if not indeed indispensable, to go abroad for the rounding out of a mining engineer's education. We had no mining schools equal to those of Germany. Our schools of technology were elementary and their equipment limited. RISE OF AMERICAN MINING SCHOOLS Now we point with true American pride to institutions which, are unsurpassed in all the world in their standard of efficiency. We know full well that the American engineer is in demand in many foreign parts and when we read recent scientific treatises published abroad we are amazed to find them unfamiliar with many of the more advanced ideas which have here already come to be an everyday part of our professional knowledge and equipment. Blessed with a country of unrivalled natural resources, dwelling in a latitude whose climate is most conducive to enterprise, peopled with races of inventive and organizing genius with equality of individual opportunity, our industries have grown and expanded until our output has reached staggering proportions and the draft upon our mineral reserves is appalling. Coupled with this development has arisen a demand for engineers which has brought into our schools of technical science larger and larger numbers of young men whose imagination has been stimulated by the success of their predecessors who happened to be contemporary elements in the recent industrial expansion and prosperity.

Jan 1, 1923

By W. W. West

MACHINERY used for size reduction of materials may be divided into three classes-depending upon the manner in which the crushing force is applied. In the first class could be listed the primary crushing units, such as the jaw crusher and gyratory crusher-which crush to coarse sizes by applying pressure intermittently between converging surfaces. In the second class may be listed crushing units, such as the hammer mill, roller mill, and ball mill, which crush principally by grinding or attrition. In the third class is the impact mill which, as the name infers, crushes by impact. The second and third classes generally include machinery used as secondary units for intermediate or fine crushing and grinding. Theory of Crushing by Impact Throw a stone into the air and give it a severe blow while it is momentarily suspended, and it shatters into several pieces. The impact crusher uses this "batting" principle, but carries it one step further. As the material to be reduced enters the crushing chamber, it receives a severe free-air impact blow by hard-hitting beaters suspended from rotor discs. The shattered particles formed are then driven at high velocity against impact blocks, where a further reduction in particle size takes place. The rebounding particles from the impact blocks are again caught by the beaters, and the process repeated until the material is swept out of the open bottom of the crusher. Impact Crushing Versus Attrition Crushing Fig. 1 shows a Hammermill type of attrition crusher. This particular mill has central feed and is reversible. Because of the central feed, an impact section can be designed into it at the feed entrance for preliminary crushing, followed by the cage bar attrition area for final sizing. The material is caught and held in a crushing chamber enclosed by grate bars or perforated plate. It remains in this chamber until it is reduced to particle size small enough to pass through the openings between the bars or in the plate. In this manner the top particle size discharged from the mill is closely controlled. As the swinging hammers pass through the bed of material, the material is broken down by a scrubbing action between hammers and material, material and grate bars, and material against material. This attrition produces a rounded particle shape, accompanied by slivers and a comparatively high percentage of fines. The crusher is especially useful in industries where the material treated is not too abrasive, such as limestone, cement or coal plants. It can be readily understood that from the maintenance standpoint, it is not suitable for hard abrasive materials such as refractories and aluminum oxides. One common type of impactor is shown in Fig. 2. The bottom of this type crusher is entirely open and the passage of the material through the crushing chamber is almost instantaneous. Liberal clearances are maintained between the impact hammers and the anvil type breaker blocks. This eliminates practically all attrition. It is the elimination of attrition that makes the impactor particularly adaptable for reducing hard, abrasive materials. The impactor is also well suited for the reduction of wet or frozen materials, which clog an ordinary Hammermill. Particles broken by impact, when examined under the microscope, show a distinct tendency toward rough, cubical shape, with a minimum of fines. Another important factor in impact crushing is that crushing is accomplished along natural cleavage lines, thus freeing foreign ores or materials.

Jan 1, 1952

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

By G. S. Scott, G. W. Jones

ECONOMIC waste caused by mine fires may become considerable,15 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters-such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control. necessarily must be based upon one or the other, or both, of these two principles. . The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion) ; and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. OXIDATION OF COAL Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored.6,16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By Raymond C. Boettner

The present work had for its purpose: 1) the identification of crack nucleation sites in AISI 4340, quenched to martensite and tempered over a range of 'temperatures; and 2) the comparison of fatigue processes in AISI 4340 with processes observed previously in pure metals From constant def1ection-bending fatigue tests, martensite boundaries were identified as the favored crack nucleation sites in quenched and tempered AISI 4340. It, also, was concluded that the fatigue processes operating- in this lous-alloy steel were similar to Processes observed in pure tnetals. ALTHOUGH much engineering data has been accumulated on the fatigue properties of quenched and tempered martensitic steels,' fatigue as a process is not as well understood in martensite as it is in pure metals.' Important features of the fatigue process, such as the identity of the nucleation sites, have not been determined in the commercially important high-strength low-alloy structural steels. The present work had for its purpose: 1) the identification of crack nucleation sites in a low-alloy steel, i.e., AISI 4340, which had been quenched to martensite and tempered over a range of temperatures; and 2) the comparison of fatigue processes in the AISI 4340 with processes observed previously in pure metals. This comparison of the fatigue processes in the different tempers was restricted to the high-strain low-cycle part of the S-N curve. Under these test conditions, previous work on a number of metals has shown that a large number of cracks are nucleated in less than 30 pct of the fatigue life.3 Furthermore, crack nucleation sites are not restricted to inclusions but are also associated with intrinsic structural characteristics of the metal. MATERIAL A 20-lb ingot of vacuum-melted AISI 4340 (for composition see Table I) was hot-rolled to 1-in.-diam rod and then cold-rolled to a 1-in.-wide strip, 0.08 in. thick. Fatigue specimens, see insert of Fig. 1, were machined from the strip with the long dimension parallel to the rolling direction. m this orientation, the stringers of 1 to 2 p inclusions present in the sheet lay parallel to the stress axis in the specimens. The specimens were austenitited at 2050°F in order to obtain a large prior austenite grain size, i.e., 2 mm, which facilitated the subsequent identification of the prior austenite boundaries. A helium atmosphere was used to minimize decarburization. After austenitiza-tion at 2050°F, the specimens were transferred to a 1450°F furnace so that specimen distortion was held to a minimum in the subsequent oil quench. Previous work4 indicated that refrigeration in liquid nitrogen prior to tempering reduced the percentage of retained austenite in the quenched specimens to less than 5 pct. Tempering was carried out in air over the temperature interval of 200°to 800°F to produce a range of mechanical properties, Table I. The preparation of the fatigue specimen was completed by grinding about 0.005 in. from each surface and electropolishing in a chrome trioxide-acetic acid solution for 30 min. Examination of etched cross sections of specimens prepared in this fashion showed the foregoing specimen preparation to be adequate for the removal of the decarburized layer present after the heat treatment. Transmission electron microscopy showed that the as-quenched microstructure of this alloy consisted of a mixture of martensite plates containing either a high density of dislocations or microtwins. Previous work5'6 indicated that in the course of oil quenching autotem-pering resulted in the formation of E carbide on the martensite and microtwin boundaries. Tempering for 2 hr at temperatures up to about 400°F resulted in further precipitation of the E carbide. Finally, at about 400°F, cementite began to replace the E carbide on the martensite and microtwin boundaries in addition to forming a Widmanstatten structure within the plate matrix. EXPERIMENTAL S-N curves were obtained using electropolished specimens cycled at 1800 cpm as cantilever beams in fully reversed bending at selected constant deflections. The deflections were translated into surface strains by means of a calibration curve obtained through the use of strain gages. An argon atmosphere was used to minimize environmental effects. To investigate the development of fatigue slip bands, the specimens of the different tempers were unidirec-tionally bent to a surface strain of 0.005 to 0.007, photographed to record the location and appearance of slip bands so introduced, and then cycled to failure

Jan 1, 1968