Search Documents

By M. R. Tek, L. K. Thomas, D. L. Katz

Threshold displacement pressures are needed to determine how much overpressure can be used in storing natural gas. An experimental technique for determining threshold pressures by displacing water with gas from samples saturated with water is presented. Threshold pressures for eight low permeability samples were measured. Threshold pressure data obtained in this work, plus data on higher permeability samples reported in the literature, are correlated with porosity, permeability, surface tension and formation resistivity factor. Mercury injection pressures also were measured and correlated with air-water threshold pressures. Threshold pressures were found to be independent of time. An aerial photograph of gas emerging from the top of a core shortly alter its threshold pressure has been exceeded shows that the gas bubbles are uniformly distributed across the face of the core. Channeling will occur, however, when an increased gas phase permeability is reached, A porous medium can be re resealed alter its threshold pressure has been reached, provided it has not been desaturated below a fixed saturation. Its new threshold pressure will be lower than when the sample is 100 percent saturated with water. INTRODUCTION The degree of overpressure in excess of the discovery pressure that a gas storage reservoir can withstand is determined by the ability of its caprock to contain gas, providing the pressure does not exceed the structural limit of the reservoir. The retention of gas in a reservoir by a caprock saturated with water is a result of the capillary forces acting at the gas water interface. Without the presence of water in a caprock, gas would leak out of the reservoir at a rate determined by the permeability of the caprock to gas. The ability of a caprock to contain gas is expressed in terms of its threshold displacement pressure, which is defined as the minimum pressure needed to initiate the displacement of a wetting phase by a nonwetting phase from a porous medium 100 percent saturated with the wetting phase. The gas industry must be able to predict how much "overpressure" a gas reservoir can withstand before leakage occurs by gas displacing water from caprock overlying the reservoir. This is of economic importance since the storage capacity of a gas reservoir is proportional to its pressure. The discovery pressure for most reservoirs is found between the upper and lower limits1 shown in Fig. 1. Discovery pressures in excess of their hydraulic pressure gradient are attributed to the compaction of an isolated shale formation by the overburden.2.3 The lower limit of 0.433 psi/ft corresponds to the weight of the overburden, the gradient of the rock itself. Somewhere between

Jan 1, 1969

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members who registered at Institute headquarters during June: Ralph H. Sweetser, Columbus, Ohio. O. M. Bilharz, Rivermines, Mo. Etienne A. Ritter, Colorado Springs. Colo. Joseph A. Holmes, Washington, D. C. Dwight E. Woodbridge, Duluth, Minn. Francis Church Lincoln, Urbana, III. Arthur Chippendale, Mexico City, Mex. William E. Saunders, Philadelphia, Pa. E. T. Miller, Louisville, Ky. E. P. Ross, Johnson City, Tenn. Jesse Scobey, Denver, Colo. H. M. Boylston, Cambridge, Mass. Charles Rhodes, Auckland, N. Z. Edward Keller, Perth Amboy, N. J. John W. Finch, Denver, Colo. F. G. Cottrell, San Francisco, Cal.

Jan 7, 1913

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

By Walter E. Mingramm

The construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquefied air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the difficulty and cost of keeping on hand a large quantity of liquefied air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found

Jan 1, 1909

By R. Hogg, R. Schaller, P. Luckie

OVERVIEW This paper is a review of two fine particle processing unit operations - classification and mixing. It may appear that these two processes have nothing in common. In fact, the simplified symbols used to represent them on flowsheets - a tipped equilateral triangle such that the base lies along the vertical - are totally reversed. For classification, a splitting action, the apex of the tipped triangle is to the left of the vertical base. A horizontal flow arrow indicating input is drawn to the apex while two horizontal flow arrows indicating outputs are drawn from the top and bottom of the vertical base, respectively. On the other hand, for mixing, a blending action, the apex of the tipped triangle is to the right of the vertical base. Two horizontal flow arrows indicating inputs are drawn to the top and bottom of the vertical base, respectively, while a single horizontal flow arrow indicating output is drawn from the apex. Classification is the process whereby a collection of particles is separated into two or more portions differing in some physical or chemical property. Mixing is the process whereby two or more portions of particles differing in some physical or chemical property are combined into a collection of particles. The common bond that links them together in the same review is the fact that they both require dispersion of the particles in order to achieve successfully their individual objectives.

Jan 1, 1980

By R. S. Rickard, M. C. Fuerstenau

Anodic polarization curves for iron dissolution and cathodic polarization curves for copper deposition and ferric and hydrogen ion reduction were studied. These results were used to predict the relative rates of the reactions: The rates of the first two reactions were found to be first order with respect to the reacting ion, and the rale-controlling step was diffusion of the ions to the callzode surface. The rate of hydrogen ion reduction in an oxygen-free solution is dependent on the reciprocal of the square root of the hydrogen ion activity. In solutions containing oxygen, the rate of hydrogen reduction becomes dependent on the square root of the partial pressure of oxygen. At equal concentrations copper precipitation occurs about twice as fast as ferric ion reduction. In an air-saturated solution containing 0.01 M cupric ion at pH 2, the rate of hydrogen ion reduction zs about 10 times slower than that of copper precipitation. At pH values below 3, the rate of hydrogen reduction in oxygen-free solutions is very slozu. COPPER cementation has been utilized industrially for many years as a means of recovering copper from aqueous solutions. There are many different types of cementation plants, but all simply provide a means of contacting iron with relatively dilute copper solutions. In the past little or no attention has been paid to rates or mechanisms of the reactions involved. As a result, this and other studies'-3 have been undertaken recently to establish the important parameters in this system. The reactions involved in copper cementation by iron are: Since transfer of charge is involved in every case, these reactions should be considered from an electrochemical point of view. In any electrochemical system involving electrolytic conduction, passage of electrons necessitates ion transfer to the respective electrodes according to Faraday's law. The current in the system will be proportional to the rate of ion transfer, and, therefore, when the current in the galvanic cell is known, the rates of the reactions involved can be determined. Galvanostatic electrode measurements5" are applicable for these electrochemical studies, in that with this technique polarization curves (current density vs electrode potential) are established by impressing a constant current through an electrode and measuring the electrode potential. Once the current density, electrode potential, and reacting area are known for each reaction in this cementation system, the rates of the iron-consuming reactions can be determined. EXPERIMENTAL MATERIALS Several metal electrodes were used in this investigation; they are shown in Table I. Solutions were made with reagent-grade salts and conductivity water. Air, nitrogen, and oxygen were employed. All of these gases were saturated with water and degreased prior to use. EXPERIMENTAL PROCEDURE The experimental work was divided into two general areas. The first area involved galvanostatic measurements, which were used to determine the rates of reactions as a function of various parameters. The second area comprised actual cementation experiments to check the rates predicted from the electrode measurements. Galvanostatic Electrode Experiments. Polarization curves were obtained using a standard galvanostatic technique5'= with the apparatus shown in Fig. 1. The various electrode polarization experiments were run the same way except for changes in solution composition, polarity, and type of measured electrode. The general procedure involved the following steps: 1) a solution was made 0.5 M in sulfate ion and to the desired cation concentrations; this solution was placed in a constant-temperature bath and saturated with the desired gas; 2) the electrodes were cleaned and placed in the electrode holder; 3) the previously cleaned apparatus was assembled and immersed in a constant-temperature water bath (temperature controlled to ± 0.05"C); 4) the electrode was then positioned; the solutions were introduced, and the polarization meas-

Jan 1, 1969

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

By H. Furman Byars

INTRODUCTION of bottom dump hauling units into the Ray, Ariz., stripping operation of the Isbell Construction Co., was motivated by several reasons, with what appears to be debatable results. The accepted theory of truck design for use in open-pit holds that end dump vehicles are the most adaptable for the work. But, because operations of the bottom dump, under certain construction and haulage conditions, proved economically feasible, the unit was put to work in the Ray copper pit. The decision to try bottom dump was reached after considerable observation of the unit in action on construction of earth filled dams, levees, airport construction and several other similar tasks. Basic tire design also motivated the choice. All things being equal, a vehicle running on low pressure single tires will outperform another operating on dual high pressure tires, providing load carrying capacities are the same. The investment required to equip a vehicle with four single tires to handle the same load as one with dual tires mounted on two axles and single front axles is about 60 pct greater. Thus, in order to reach the break even point on tire costs, single tires must operate 60 pct longer. Comparison is made with a truck outfitted with 10 16:00x25 tires. Two other factors were considered in selecting bottom dump trucks. It was felt the bottom dump principle would work well in dumping ore into a hopper where gate design fits this particular method. Also, with the absence of hydraulic dumping, ore pollution with oil is reduced. The mechanical simplicity of the unit also lent weight to its choice. Ordinary reasoning indicated maintenance costs would be low compared with other units carrying similar loads. The bottom dumping principle is not new. It dates back to the days when horses were used to haul the same kind of rig. The unit employed at Ray holds 25 cu yd struck measure, or approximately 42 short tons. Dumping is accomplished by releasing an air cylinder opening a dog holding the doors. Doors are closed by a cable system operating off a wheel wind deriving power by friction with the trailer tire. The unit is mounted on four 27.00x33 and two 14.00x24 tires on the front axle. The power unit is a 300 hp Cummins engine. Hydraulic power boosts the steering. A straight mechanical drive and friction clutch with 10 speeds is used. Conditions Not Ideal Top performance of the truck can be expected only under the conditions for which it was designed, in particular grades under 5 pct, handling fine material, and dumping where one thin layer can be placed on top of another. The machine will handle 42 tons per haul, operating at high speed, with only seconds used for dumping. On a 2 or 3 pct grade over a one mile haul,

Jan 1, 1952

By L. W. Casteel

St. Joseph Lead Company's Southeast Missouri mines have been successfully converted to the use of ammonium nitrate and fuel oil as a blasting agent. This is significant to the company because it means a savings of a quarter of a million dollars per year. It is significant to the mining industry because of the unusual conditions involved and the methods and materials used to overcome them. St. Joe has been mining the low grade lead deposits of southeast Missouri since 1864. This ore occurs as disseminated galena in widely scattered pockets within the Bonneterre dolomite. The daily production of 20,000 tons is obtained from several hundred small, room and pillar stopes covering an area 10 miles long and five miles wide. Distribution of explosives and other materials is a real problem. Drilling in the stopes is done with air legs, column- mounted machines or jumbos, depending on the size and location of the stope. Drill hole sizes vary from 1 3/8-in. diam down to 1 1/8-in. Each driller charges his own holes and shoots them at the end of the shift. Numerous shafts provide natural ventilation which is supplemented in isolated areas by churn drill holes equipped with blowers. Water, in most stopes, is not a serious problem, although the mines do produce about 20,000 gpm.

Jan 5, 1962

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette' recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.'."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy's law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum deposit, Eureka County, Nevada, occurs In a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusive. For samples from the 25000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8: 1 at 10-mesh, 8: 1 at 70-mesh, 6: 1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp 1s used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of ± 25%. The error distribution is not based. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1984

By E. N. Pennebaker

The concept of "unitization" comes from the petroleum industry. Of this, Campbell says: "Unitization is the process whereby the owners of adjoining properties pool their reserves and form a single unit for the operation of the properties. The revenue from operation of this unit is then divided in accordance with the basis established in the unit agreement. "The purpose of such an agreement is to produce the reserves more efficiently and thus to increase the profit to every participant."'

Jan 8, 1973

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

Discussion of the paper of Leonard Waldo, presented at the New York meeting, February, 1911, and printed in Bulletin No. 76, April, 1913, pp. 555 to 559. HERBERT HAAS, San Francisco, Cal. (communication to the Secretary*):-Referring to Leonard Waldo's paper on Temperature Conversion Tables, I believe the following formulas can be easily remembered, and by reference to the thermomter scales of Fahrenheit (F.), Celsius (C.), and Réaumur (R.), their derivation and relation are at once understood n° F. = 4/9 (n°-32) R. = (n°-32) C. n° C.=(9/5 n° + 32) F. = 4/5 n° R. n° R.=(9/4 n° + 32) F. = 5/4 n° C. As the freezing point of water is at 32° F., corresponding to 0° C. and 0° R., 32 must be deducted from the Fahrenheit degrees when these are converted into C. or R. degrees. Likewise, to C. or R. degrees converted into F. degrees 32 must be added. The fractions 4/9 and 5/9 and their reciprocals are obtained thus:

Jan 5, 1913

By S. Kado, G. Derge, L. Yang

Self-diffusion coefficients of silver in molten silver have been measured by means of the capillary-reservoir method in the temperature range 1002" to 1105°C. The results can be .represented by the equation D = (7.10 i 0.06) X 10-4 exp [(—8150 ± 1130)/RT]. The heat of activation agrees within the limit of experimental uncertainty with that for the viscous flow. The validity of the Eyring and the Stokes-Einstein equations are examined on the basis of the self-diffusion coefficients obtained and the known viscosity data of molten silver. MEASUREMENT of the self-diffusion coefficient of silver in molten silver was made in the temperature range 1275° to 1378°K, using the capillary-reservoir method and &"' as the radioactive tracer. The experimental arrangement is shown in Fig. 1. Silver of 99.99 pct purity (fine silver), was melted and degassed in vacuum in a graphite crucible situated inside a McDanel vacuum jacket. The crucible (4 in. tall and 1 in. ID) was protected both at the top and at the bottom with graphite shields and contained about 220 g of silver. The sample holder was a piece of graphite rod (1 in. long and 1/2 in. diam) with 4 capillaries drilled longitudinally into it. The holder was screwed onto a long graphite rod (12 in. long and 74 in. diam) which was connected to a steel disk hanging on a nylon string through a glass pulley. The steel disk kept the sample holder at the center of the McDanel tube and was heavy enough to overcome the buoyancy when the holder was lowered into the molten silver. By turning a handle connected to the pulley through a tapered glass joint, it was possible to raise or lower the sample holder without breaking the vacuum. Two such arrangements were constructed, sitting side by side in 2 Kanthal furnaces. One with non-radioactive silver in its crucible was used for the diffusion run and the other with radioactive silver in its crucible was used for filling the capillaries. To fill the capillaries with radioactive silver, the sample holder was degassed first and then lowered into the radioactive molten silver in vacuum. Purified argon gas was then admitted into the system to push the liquid silver into the capillaries. After cooling in argon, the filled capillaries were polished on emery paper to expose the top of the rod and used immediately as samples for the diffusion run which was carried out at the same temperature as that used for filling the capillaries. During the diffusion run, the samples were degassed in vacuum and lowered slowly into the nonradioactive molten silver before purified argon was admitted into the system. After a predetermined period of time, the samples were raised out of the melt and cooled in argon. The temperature of the melt was measured before and after the run with a chromel-alumel thermocouple inside a McDanel protection tube. Another chromel-alumel thermocouple attached to the outside wall of the McDanel vacuum jacket was used to indicate any fluctuation in the temperature of the furnace during the run, which was found to be less than ± 2°C for the longest run made (93 min). The temperature gradient inside the molten silver was found to be negligible. No significant difference was observed in the results obtained whether the melt was stagnant during the run or was stirred by raising and lowering the sample holder slowly a few times a minute for a distance of about 1/4 in. inside the melt.

Jan 1, 1959

By J. R. Thoenen

THE consensus of opinion in the published literature on. Grecian magnesite is that it has been formed by alteration of the serpentine, which in turn was itself a product, of metamorphism from the original olivine intrusion. The general opinion seems to be that the magnesite was formed by descending waters heavily charged with CO2. Inasmuch as this opinion is held by engineers far better qualified than I to speak authoritatively on this subject, I hesitate to dispute that theory. However, certain occurrences coming under my observation do not, to me at least, seem to-entirely substantiate this theory. LOCATION Most of the Grecian magnesite comes from the Island of Euboea, although more recently some deposits have been opened on the mainland near the City of Saloniki, which prior to the war was Turkish. The island, comprising a state or province in the Greek political structure, is roughly 110 miles long and varies from 10 to 30 miles in width. It lies off the east coast of the Greek peninsula in the AEgean Sea with its long axis extending in a northwest-southeast direction. It is separated from the mainland by a long narrow arm of the sea known as the Atalanti Canal. Chalkis (Halkis), the capital on the west coast of the island, is the northern terminus of a branch of the state-owned railway and is connected with the mainland by a single-span, movable, highway bridge, roughly 150 ft. long.

Jan 1, 1928

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By E. S. Bumps

A series of macrographs are presented for the purpose of graphically recording the strain phenomenon that accompanies the energy transition in the Charpy impact testing of a mild steel that is susceptible to strain aging. STRAIN patterns in mild steel Charpy impact specimens were obtained in order to determine whether, on the first appearance of plastic strain during deformation, the initial fracture cracks appear in the region of plastic strain or in the elasti-cally deformed regions between. Although this attempt to locate the initiation of cleavage was not successful, the observed strain patterns illustrating various stress conditions in partially deformed Charpy specimens are presented along with a discussion of the possible dependence of transition energy on the yield phenomenon. Earlier work on the development of strain patterns in mild steel have been reported by Fry1 and later by Jevon.2 Harris, Rinebolt, and Raring3 observed characteristic strain markings on the surface of Charpy V-notch impact specimens fractured above and below the transition temperature which they presented schematically. It is intended that the strain figures presented here will add to the literature a graphic correlation of strain with transition energy in impact specimens. Samples of % in. round hot rolled, 0.20 pct C steel were machined to standard 0.394 in. sq, V-notch Charpy impact specimens. Preliminary testing involved determination of transition temperature, Fig. 1, using a Sontagg impact tester. These data were subsequently used to select temperatures above, within, and below the transition range at which specimens were partially deformed. Partial deformation was obtained by either varying the energy or the testing temperature, see Table I. Macroscopic strain figures shown in Figs. 2 to 19 were produced by several metallographic repolish-ing and etching steps. The macroetchant used was as follows:4 120 g HCl, concentrated; 100 ml water; and 90 g cupric chloride. Strain figures were obtained on the outer surface and on sections through the central portion of the impact specimens in order to determine an approximation of the volumetric strain pattern. In the tensile strain figures reported by Jevon, it was found that strain etching would not work immediately following strain unless the material was heated to 200°C. The impact strain patterns presented here were obtained without this heating, but the specimens were not etched until ten months after straining. This confirms a discussion of Jevon's paper, in which it was pointed out that strain figures can also be developed after aging for long periods of time at room temperature. Hardness of the strained and unstrained portions, revealed by the etched pattern, was explored using R, impressions converted to R, hardness values. Discussion of Results In the impact test, as in the tensile test, some parts of the specimen yield and deform plastically, while other regions are deformed only elastically. The plastic deformation bears a relation to the imposed stress pattern. In the strain figures presented here, the plastically deformed regions are the dark etching ones. The strain figures are always symmetrical because the stress state in the Charpy-type specimen under impact loading is symmetrical. The difficulties encountered to produce initial cracks are intimated in Figs. 2 and 4. At a temperature of —75ºF, the stress was not sufficient to pro-

Jan 1, 1953

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950