Search Documents

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"' is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By David Baker

When the skip-hoist was first tried as a means of filling the blast-furnace it made a great many enemies and very few friends among furnace managers. This state of affairs continued until the Duquesne furnaces were built, which demonstrated not only the possibilities of a furnace-stack in the way of production, but also the ability of the skip-hoist to charge the materials necessary to produce the large tonnlage obtained. Every furnace manager, who has operated stacks fitted with the vertical hoist and the hand-barrow system of filling, remembers that the momentous question about the furnace, particularly during a good run, was: "Are you keeping her full ?" and many a good run has been spoiled by the furnace " getting away from the men." With the new birth of the skip-hoist this trouble was eliminated ; but alas! Other and more important difficulties arose. The distribution of the stock, the importance of which is never learned until many different ores and fuels have been tried, demanded closer attention. With all the defects of the hand-barrow system, the distribution—When the top fillers were conscientious in carrying out the scheme of filling arranged after thoughtful consideration by the manager—mas above criticism. It is said that the modern skip-hoist, equipped with an elliptical hopper and receiving-cylinder, and discharging over a small bell into the main hopper, will give just as good results as those obtained with hand-barrow charging, but I cannot agree with this statement. I grant, that under very favorable conditions, the mechanical furnace-top will do apparently as well as the

Jan 1, 1905

Alexander Forsyth, Southport, Me. (communication to the Secretary): In Mr. Irving's able and interesting paper he describes minutely the appearance of the wolframite and its association with the refractory siliceous gold-ore. He also describes this gold-ore, but fails to mention the important pockets of metallic gold found in the Lead City occurrence of it. I use the term " metallic " in preference to the more usual " free," for it has been found that this gold is not easily amalgamated. Metallic gold is comparatively rare in the refractory siliceous gold-ores of the Black Hills; hence its occurrence in considerable amounts in the Lead City wolframite district deserves notice. I possess a beautiful specimen from the Harrison mine. It is a lump of drusy, granular ore, about 6 in. in diameter. The gold .is " shot" through it in large and small pin-heads; and in two specially oxidized areas, each about 11/2 in. in diameter, it is peppered full. The famous " Grantz strike," made in the Lead City wolframite locality, produced many beautiful gold specimens. This district affords an excellent example of the repeated discovery of new mineral values upon old ground. By reason of its proximity to the Homestake vein, this wolframite deposit was inevitably traversed many times by experienced geologists, mineralogists and mining engineers, who evidently must have thrown aside, with no thought of wolframite, the lumps of " black iron " lying about. I have the admission of an able geologist that, six months before the wolframite was discovered, he visited some of the very mines where it occurred, and passed it by as magnetic iron-ore. At the time of the discovery, the mineral was scattered over the gold-mine dumps in no small quantities, having been culled as worthless out of the gold-ore. It remained for

Jan 1, 1902

By H. W. Smith

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

The Committee on Nominations begs to submit the following names as its nominees for the respective offices indicated: For President, SIDNEY J. JENNINGS, New York. For Vice-Presidents. C. W. GOODALE,* Butte, Mont.; MARK, L. REQUA, San Francisco. For Directors, J. E. JOHNSON, JR., New York; ALLEN H. ROGERS, Boston; HOWARD N. EAVENSON, West Virginia; ROBERT AI. RAYMOND, New York; WILLET G. MILLER, Canada. The nomination for President has attracted the attention of a large number of members, as is evidenced by the receipt of many hundreds of letters and postcards. Most of these favored either Sidney J. Jennings or Philip N. Moore, each of whom received many cordial endorsements. Such a wide interest on the part of the members is a very wholesome sign, but where there is so much activity it is natural to expect a certain amount of criticism. Some of the letters indicate that the authors feel that the nomination of President should be left entirely to the Committee on Nominations without any effort by the members at large to influence them. Others feel that the nominations are largely controlled by a small group and that the members at large can have little influence. As the result; of the experience of the last few months; a majority of the Committee on Nominations begs leave to suggest that the method of making nominations be changed so that two candidates, at least, for the various offices to be nominated, and suggests that the Directors appoint a committee to investigate this question thoroughly with. a view to making definite recommendations. In accordance with its opinion that the best interests of the Institute would be served by a change in the Constitution, allowing the nomination of two candidates, and in view of the fact that this Committee has no authority to make more than a single nomination for each office, considering the high standing of both Mr. Jennings and Mr. Moore and the large number of members favoring each of these gentlemen, this Committee respectfully suggests the desirability of ,the immediate nomination of Philip N. Moore by a petition of 25 members in accordance with the present Constitution. This Committee regrets, its inability to make two nominations. Respectfully submitted, S. W. MUDD, Chairman.

Jan 1, 1917

By Juan Sodi, John F. Elliott

The standard free energy of ReS2 has been measured in the range of 1050° to 1250°K using H2/H2S mixtures and a slight variation of the method described by Hager and Elliott.1 The result is: The experimental method and apparatus were modified slightly for this study. Measurements on Cu2S were made to verify the application of the method to the work on ReS2. THE EXPERIMENTS AND RESULTS Briefly, the experimental method consisted of exposing a chip of copper or rhenium at a known temperature for 8 hr to a slowly flowing gas stream at the same temperature in which Ph2S and PH2 were known. The chip was withdrawn quickly from the hot furnace, and subsequently it was inspected for the presence of a sulfided surface. In the experiments described here, there was no ambiguity in any case as to the presence or the absence of the sulfide. At a given temperature, gas compositions for sulfidization were explored systematically until two compositions were found whose values of ?G°, Eqs. [I] and [2], were within approximately 100 cal of each other, one of which was sulfi-dizing and the other was not. These are termed the "straddle" compositions and it is assumed that the equilibrium composition lies between them. The chief modification to the apparatus, which is shown schematically in Fig. 1 of Ref. 1, was to support the metal specimen on a small alumina boat which could be moved along the reaction tube, 6 mm ID, by platinum wires. An appropriate seal at each end of the reaction tube permitted the sample to be moved from the cold end of the tube into the hot zone in 2 to 3 sec, and the sample could be withdrawn equally rapidly. Thus, it was possible essentially to quench the specimen from the reaction temperature with the reaction gas or helium flowing and without danger of breaking the reaction tube. The usual practice at the end of the experiment was to switch the gas system to the helium tank, flood the reaction chamber with helium, and pull the sample out of the hot zone. The purpose of the modification was to permit study of the sulfidization of copper without the complication of the back-reaction between the gas and the specimen as the latter cooled during slow withdrawal of it from the hot zone; this was a problem in the earlier work.&apos; A further improvement located the tip of the temperature-indieating thermocouple and the specimen precisely at the hottest part of the furnace. A carefully calibrated thermocouple, with its tip at the position of the specimen and with other conditions duplicating those of an actual experiment, showed that in the temperature range of 900° to 1122°C the temperature of the specimen differed from that of the tip of the indicating thermocouple by less than 0.5°C. The two positions were 0.5 cm apart. The reaction gas was prepared from ultrahigh-purity hydrogen (<l ppm O2, <0.5 ppm H2O) and CP grade hydrogen sulfide (99.5 pct H2S). High-purity helium (99.995 pct He) was used. All of these gases were purchased from the Matheson Co. All flow meters were recalibrated by the soap-bubble method with hydrogen, H2S, helium, and several gas compositions used during the study. These calibrations gave a linear relationship with a slope of 1.0 for the plot of log flow rate vs log pressure drop across the flow meter, in accordance with the Hagen-Poiseuille equation. The analysis of the gas was determined in the same manner as was reported previously. Good checks were obtained between the composition of the gas established by the flow-meter settings and by chemical analysis of the gas taken after the mixing bulb and ahead of the furnace. The pressures of H2S, H2, S2, and HS in the equilibrium gas at temperature were calculated from the following data :3 The pressures of the species S and S8 were negligible for the conditions of the experiments.3 There was no sign of vaporization of ReS2 either by weight loss or deposits in the reaction tube. Thus it is not possible to account for the apparent volatility of the compound reported by Juza and Biltz.2 The inlet gas composition and the calculated equilibrium ratio of PH2 S/PH2 for the "straddle" points of each experiment are shown in Table I. The specimens of metal for the experiment were small clippings of annealed copper (99.9+ pct) sheet 0.005 in. thick that was obtained from Baker and Adamson and of "high-purity" rhenium (99.9+ pct) sheet 0.005 in. thick that was purchased from Chase Brass and Copper Co. A specimen was removed from the apparatus; inspected for the presence of the sulfide, and then stored in a sealed vial. A fresh clipping was used in each measurement. The condition of the surface of each specimen after the experiment is noted in Table I.

Jan 1, 1969

By Henry G. Petrow, Edward S. Porter

MAJOR occurrences of lignite with significant uranium concentrations have been reported in western parts of the Dakotas, especially in Harding County, S.D., and Billings and Slope counties, N.D. Samples containing as much as 2 pct U3O8 were received at the Winchester Laboratory, but those deposits reportedly of major significance have generally contained 2 to 4 lb of uranium per ton of lignite. Most of the uranium appears to be associated with the carbon in the lignite as a urano-organic complex, although in most instances analysis of inorganic material has shown uranium values. Molybdenum is similarly associated with the carbon, and its concentrations generally parallel the uranium. The noncarboniferous material is mainly composed of gypsum, jarosite, bentonite, sandstone, and miscellaneous carbonates and silicates. The heating value of these lignites has been determined as about 3500 Btu on a dry lignite basis. The ash content of lignite has varied widely, the important samples containing 30 to 60 pct ash on a dry lignite basis. Because of the significant upgrading of uranium values obtained by ashing the lignite, and because recovery of uranium from raw lignite presented formidable processing problems, major emphasis at Winchester has been placed on devising methods to recover uranium from lignite calcines. Proper roasting removes the problem of organic fouling of solutions, reduces the size of the leaching plant for an equivalent uranium throughout, and generally provides equal or better acid leaching efficiency with less acid than can be obtained from the raw lignite.

Jan 9, 1957

By W. R. Hudspeth

AS an outgrowth of its spodumene recovery operation at Kings Mountain, N. C., Foote Mineral Co. has been recovering a heavy mineral by-product. Foote leased this idle plant in 1951, reactivated it, using a new spodumene recovery process, and purchased plant and properties in October 1951. While the operation at Kings Mountain is primarily concerned with the production of spodumene concentrate, pilot plant work determined that the pegmatites also contained heavy minerals including cassiterite. Plans were made to recover the heavy minerals as a by-product and the flowsheet incorporated these facilities when the mill was modified for the new spodumene recovery process. The orebodies consist of spodumene, feldspar, quartz and mica. Apatite, tourmaline, and beryl are present in small quantities. The wall rock is pre- dominantly hornblende shist. The heavy minerals, including cassiterite, columbite, pyrrhotite, monazite, pyrite, and rutile represent about 0.2 pct of the ore. The fine-grained heavy minerals are disseminated throughout the dikes, apparently unassociated with the spodumene. The pegmatites are quarried and secondary breakage is by mud-capping and block-holing. Power shovels load into trucks transporting the ore to a coarse ore bin. A Telesmith 10x36-in. apron feeder delivers the ore to an 18x36 in. Traylor Jaw crusher adjusted to discharge -3 in. product to a primary conveyor. The conveyor delivers to a 4x5-ft Tyrock single deck vibrating screen using 3/4 in. cloth. The screen undersize is elevated to the crushed ore bin. Screen oversize goes to an Allis-Chalmers Hydrocone Crusher fitted with 4 in. concave and set to deliver approximately 66 pct minus 3/4 in. The crusher discharge returns to the primary conveyor. The crushing and screening installation has a capacity of about 60 tons per hour. Spirals The crushed ore is delivered at a rate of 350 tons per day to two 6x8-ft Hardinge Pebble Mills, equipped with 20 mesh Ton-Cap trommel screens. The screen oversize is pumped to a 12-in. hydroclone for primary desliming. The hydroclone underfl spirals. There is no heavy mineral loss in the hydro-clone overflow. The spirals bank consists of eight 5-turn Model 24-A Humphreys Spirals. The top port and the last four ports of each spiral are blanked, the remaining nine port splitters are adjusted to remove about 5 pct feed weight. The heavy mineral rougher concentrates are upgraded on a Deister Overstrom table. The spiral concentrates contain approximately 4 pct heavy mineral, and the spiral reject, which goes to another section of the plant for spodumene recovery, contains about 0.03 pct heavy mineral. There is an interesting feature in the spirals installation. An adjustable splitter mounted on the discharge boxes splits out a mica fines product containing very little heavy mineral. The mica product is cleaned by spiralling and screening. Thus the spirals recover two products; mica, and a heavy mineral rougher concentrate. Table Treatment The rougher spiral concentrate goes to a Deister Plato table, modified to receive a Deister-Overstrom No. 6 rubber cover with sand riffles. The table is operated with a 5/8 in. stroke, 270 strokes per minute, and a slope of 1/2 in. per ft from feed to tailings side. There is no slope adjustment from motion to concentrate end. Wash water consumption is relatively high, since the large spodumene grains tend to report with the fine heavy minerals. A middling band about 4 in. wide is maintained in order to produce clean concentrate. The middling, representing about 10 pct of table feed, is recirculated by air-lift. A band of concentrate grade coarse spodumene occurs just below the middling. This is removed and delivered to concentrate storage. The table tailing, containing approximately 0.7 pct heavy minerals, is returned to the spodumene feed preparation circuit. The heavy mineral table concentrates are approximately 45 pct cassiterite, 33 pct columbite, 14 pct pyrrhotite and 8 pct monazite, together, with some rutile, pyrite, and copper from blasting wire. Concentrate is collected at 24 hour intervals. and dried. If the concentrate remains in wet storage appreciably longer surface oxidation takes place which seriously interferes with the subsequent magnetic separation process. About 150 lb of heavy mineral concentrate is produced per 24 hours and shipped to the company&apos;s plant at Exton, Pa. for final separation into tin and columbium concentrates.

Jan 1, 1952

By S. S. Deshmukh

An important element of evaluating a materials- handling system by simulation lies in being able to examine the details of the proposed operation in a fashion which closely approximates real behavior. The added factor of flexibility permits including or deleting those parts of the problem which can be shown to be important or trivial. Used carefully, simulation can match manpower and equipment far more efficiently than conventional calculations. The same is true of interacting equipment systems. This efficiency results from being able to simulate the real fluctuations in a system by using empirical probability distributions compiled from existing operations. Simulation eliminates guessing as to efficiency, absenteeism, bunching, and the broad host of delays that influence productivity and substitutes operating data in place of the usual factors. In this respect, simulation improves detail and confidence in the reliability of engineering estimates.

Jan 1, 1970

By Freeman Bishop

The Nation&apos;s capital has one over- riding minerals-metals question: How long will prices and wages continue to move upward at the inexorable pace of the last year? Is the wage pattern to settle this year around 10%? The big industrial unions are coming into line, some of them later this year. Steel is standing in the wings for next year. Copper, steel, nickel and most other industrial metals have taken big hikes in their stride. Aluminum, which is making inroads into areas of industrial use formerly sacred to copper and some other metals, seems to be fighting to hold down its prices to attract customers from the higher-priced metals.

Jan 1, 1970

By D. Turnbull, A. M. Turkalo

It is well known that if copper that has been severely cold-worked by rolling (70-98 pct) is heated to high temperatures a small number of large grains are formed at the expense of the fine grained structure that appears upon primary recrystallization. Dahl and Pawlek,&apos; Cook and Mac-Quarie,2 Ward,3 and Boas and Bowles4 have studied this phenomenon in copper. It has been reported as taking place with measurable velocities in the temperature range 700-1080". Boas and Bowles have reported that the time necessary for the transformation is of the order of days at 700°C. According to Ward3 the number of secondary grains which appear in OFHC copper decrease with increasing perfection of cubical alignment after primary recrystallization; also the perfection of cubical alignment increases with decreasing grain size prior to the final reduction. In this investigation two heats, A and B, of especially high purity copper (99.999 pct) supplied by the American Smelting and Refining Co., were used. The behavior of samples prepared from the two heats was qualitatively very similar providing that the grain sizes established prior to the final reduction were about the same. We observed that in specimens prepared from bars which were relatively coarse grained prior to final reduction secondary recrystallization took place at a rapid rate at temperatures as low as 500°C. This is about 200-300°C lower than the temperature necessary to obtain fairly rapid transformation in OFHC copper. A 0.22 in. thick rectangular bar of lot B was cold-reduced 60 pct by straight rolling and given a penultimate annealing treatment at 250°C. Following this it was cold-reduced 90 pct and heated to various temperatures in the range 450-1040°C. The specimens were about 8 mils thick

Jan 1, 1950

By Bobby P. Faulkner

The Tennessee Copper Co.&apos;s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By J. L. Gillson

Joseph H. Birman (Chairman, Dept. of Geolcgy, Occidental College, Los Angeles, Calif.) Many thanks to J. L. Gillson for so comprehensive a survey of the titanium sand deposits of the world. Over the past two years, the writer studied rather carefully some of the Cretaceous ilmenite deposits in New Mexico and Colorado, including the Sanostee deposit shown in Gillson&apos; s map, Fig. 6. The deposits were geologically mapped and sampled, surveyed by magnetometer, and the Sanostee deposit was drilled. Moat of the genetic interpretations made by Gillson concerning the recent sedimentary ilmenites can be clearly read in the Cre-taceous deposits in New Mexico. The deposits are in marine regressive members of the Mesaverde group. The deposits trend within a few degrees of N 55° W and persistence of this trend through both distance and time (the deposits are in different members of the Mesaverde group) implies that the deposits are offshore bar accumulations. Heavy mineral content ranges from about 10 pct to more than 50 pet. Thicknesses are from 4 ft to as much as 20 ft, widths range from 150 to 600 ft, and lengths range from a few thousand feet to a few miles. All are locally or completely overlain by carbonaceous shale and thin coal. The deposits are strongly altered, and from X-ray diffraction the principal titanium alteration product appears to be anatase. Drilling of the Sanostee deposit shows that the alteration is not related to the present erosion surface but took place at the site of deposition and before burial by the overlying sediments. Iron oxide derived from the alteration cements the grains and is the chief coloring agent in the immediately overlying shales. In the Sanostee deposit, there is virtually no feldspar, the gangue mineral being almost exclusively quartz. Sorting is excellent, but the quartz grains are subangular to angular. Petrographic examination reveals that the angularity is not due to overgrowths. Therefore, short distance transport is implied. The mineralogical composition suggests a low relief granitic terrane as the source area. Feldspar may have been decomposed by weathering at the source, but an alternative preferred by the writer is that each of the deposits represents a long-term concentration site (for example a large sand bar) which was continually being deprived of light minerals by wave action and selective transport. Feldspar may have been mechanically reduced in size more quickly than the quartz, and thus its rate of removal may have exceeded that of quartz. Concentration of heavy minerals would thus occur until the marine regression removed the zone of maximum wave energy from the site. Chemical alteration would then become the most important process until burial by encroaching swamp deposits.

Jan 1, 1961

By A. T. Goldbeck

THE use of stone as a building material in relatively large blocks is recorded in ancient historical records but only within the past 200 years has broken stone in small sizes begun to have extensive use, principally in highway construction. Tresaguet, in 1764, describing his method for highway construction in France, required the top surface to be built of stone about the size of a walnut, broken by the use of a hammer. It is said that the Romans, in the top layer of their rather massive roads, used large stones bonded together with lime mortar and bedded in small stones mixed with mortar. Much of the early macadam as built by McAdam around 1815 in England was made with hand-sledged broken stone. In 1858, the use of crushed or broken stone received a great impetus from the invention in that year by Eli Whitney Blake of what is said to be the world&apos;s first stone crusher. As a consequence of that invention, stone could be crushed to small sizes with considerable ease and, as a natural result, the use of crushed stone in macadam roads and as railroad ballast increased at a great rate. Also, as portland cement came into use, machine-produced crushed stone furnished readily available aggregate. Rapidly, other uses developed, such as for fluxstone in the production of pig iron and for other metallurgical operations and chemical utilizations. These utilizations made for the rapid growth of the crushed-stone industry and this growth is still proceeding with the growth of population and the development of new uses, notably the employment of limestone for the improvement of soils for agricultural purposes. The industries of which the production of crushed stone is a part have a tonnage second only to that of mineral fuel in the mineral industries of this country.

Jan 1, 1949

By Wolfgang O. Gluschke

INTRODUCTION Virtually all countries have general legislation covering most aspects of mining and mineral processing, including investment and tax laws, safety and health regulation, and specific rules applying to exploration reporting procedures. Yet most developing countries negotiate individual agreements with foreign investors for major mineral projects, in particular when all or part of the expected output is exported. Such agreements are known under several different names, as for example concession agreement; technical assistance agreement or service contract; management agreement; production sharing contract; joint venture; or contract of work. The objectives and conditions governing such contracts are as diverse as these titles are. While a mining project is only one among a large mumber of similar undertakings in industrial countries, in most developing countries such projects usually have a dominating position within the country&apos;s economy. The general legislation is often inadequate and insufficiently detailed to cover all aspects of large projects with extensive foreign inputs and international markets. Therefore, the need for specific arrangements. Specific arrangements may also become necessary due to the complexity of markets for mineral products, the large number of participants - equity partners, suppliers, financial institutions, buyers, etc. - or economic and political conditions in the host country and fiscal regulations in the home country of the investors. Most agreements are concluded between governments, or government agencies, in developing countries and private industry headquartered in developed market economies - Canada and the United States of America in North America, Western European countries, Japan, South Africa and Australia - or, in some instances, with state-owned firms in these countries. There are fewer agreements between developing countries and the centrally planned economy countries - Eastern Europe and the USSR - which cannot be considered here because of absence of adequate information. Agreements can be concluded at any of the different stages from exploration through closing of a mine. While most contracts are negotiated at the time when a potentially viable ore body has been delineated and investigated sufficiently to anticipate a realistic time for commencement of production, other agreements start with "grass-roots" exploration, during operation of a mine, smelter or refinery or, exceptionally, after a temporary shutdown. While several major provisions are included in all types of agreements, others are covered in much more detail (or not at all) in some contracts reflecting the specific work programme of each project. While it is realized that subdivision and classification of complex contractual relations is necessarily arbitrary to a certain extent, such grouping is useful in practical terms, especially for the non-specialist. The following discussion, therefore, will start with a description of the major forms of contractual relation - concession, investment contract, joint venture, management agreement, service and production sharing contracts. Major issues covered in all, or almost all, agreements will then be dealt with. These include stages of development, corporate structure and control, fiscal arrangements, infrastructure development and environmental law, and dispute settlement and renegotiation. FORMS OF CONTRACT RELATIONS There has been marked change in the type of agreement entered into during the 1960s (and before) and the early 1970s and the period thereafter. While straight "concessions" - granting of exclusive rights to foreign investors over a certain deposit or areas with little restriction or well-defined obligations - were the rule during the first half of this century, more complex agreements have evolved since. Some of these cover every conceivable aspect, foreseen or only possible, and define rights and obligations of all partners to the last detail. Over the years, agreements have without doubt become more beneficial for the developing host countries, in part as a result of well-publicized nationalizations, as for example in Chile, and in part due to changed attitudes in all countries

Jan 1, 1985