Search Documents

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

By M. Vallée

This case study compares the actual production figures for the No. I and No. 2 copper orebodies of the Société Miniére Louvem, Val d'Or, Quebec, with the preproduction estimates and a postmortem geostatistical estimation using kriging techniques. The deposits considered are small subvertical sulphide orebodies which were mined from August 1970 to April 1973, producing 648,000 tons at 2.04% Cu versus the 1968 computed reserves of 671,000 tons at 2.51% Cu (with 20% dilution), thus showing a 25% overestimation of the copper contained. The postmortem geostatistical estimation based on the same 44 D.D.H. intersections available in 1968, shows 2.24% Cu (no dilution), compared to 3.23% Cu (no dilution) given by the conventional section method. Block by block kriging techniques were used, but within the ore contours as determined by the geologist. In this case, Characterized like many sulphide deposits by highly dispersed sample values, geostatistical kriging techniques permit a more realistic estimation of the metal contained within a given volume, than the conventional methods which overestimate it. This study has been conducted by the Mineral Exploration Research institute (IREM-MERI) for SOQUEM, and is one of the few case studies released with all pertinent data. More postmortem of this kind are required for geologists and geostatisticians to improve their methods and their "batting average".

Jan 1, 1977

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats of Formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 and the heats of solution of tellurium and selenium in liquid bismuth have been measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides have been measured in a constant temperature gradient calorimeter. The thermo-dynamic quantities are interpreted in relation to the stability of the compounds and the nature of the solid-liquid transition. THE selenides and tellurides of several elements of Group VB of the periodic system are of interest because of their electronic properties. The compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 are semi- conductors; they also have gained prominence in the fields of thermoelectricity and photoconductivity. However, little is known about their thermody-namic properties. As part of a research program on the thermo-dynamic properties of intermetallic compounds, the heats of formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 were measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides were measured in a constant temperature gradient calorimeter. The results, in addition to their intrinsic interest as thermodynamic quantities, contribute to an understanding of the stability of the compounds and the nature of the solid-liquid transition. 1) EXPERIMENTAL 1.1) Materials. Samples of the compounds SbzSe3 and Bi2Se3 were prepared by melting the elements in stoichiometric proportions in evacuated Vycor capsules followed by quenchinn in water. They- were then annealed in vacuum for 12 hr at 550°C. A sample of Sb2Te3, consisting mainly of one large grain, supplied by the Lincoln Laboratory,

Jan 1, 1964

By C. S. Smith, Chih-Chung Wang

D. Turnbull—In the opinion of the writer the most interesting result described in this paper is that the distribution of tin with respect to solidification temperature has several fairly well-defined maxima. It appears that each peak may be associated with a catalytic impurity of some rather specific composition. Recently we have obtained some additional evidence in favor of this viewpoint in experiments on the supercooling of lead droplets coated with different surface films. The distribution of lead droplets, ostensibly coated with lead sulphate, with respect to solidification temperature exhibited two distinct and reproducible maxima, one at 20" supercooling and the other at 47". On the other hand, when the droplets were ostensibly coated with halide films, no solidification was perceptible until the aggregate was supercooled more than 55". Upon further cooling a single well-defined peak centering at 60" supercooling was observed. Since the particle size distribution was the same in these two sets of experiments it appears that the most reasonable interpretation of the results is that the sulphate surface film or its reaction products with lead are much more effective in catalyzing the nucleation of lead crystals than are lead halide films. C. S. Smith (authors' reply)—Dr. Turnbull's experiments with lead drops coated with various surface films are most interesting. However, before drawing conclusions from the cooling curves described in the paper as to the existence of a few nucleus types effective at a few different temperatures, one must consider the state of subdivision of the liquid metal. In the A1-Sn alloy used, the tin was not in uniform droplets but tended to collect in three distinct shapes—in long interconnecting prisms along grain edges, in somewhat elongated interdendritic branching pools. and in isolated droplets. A single nucleus will solidify only the metal in contact with it, and the heat evolved will be proportional to the connected volume. A uniform distribution of nuclei of random effectiveness in such an alloy will cause peaks on the specific heat curve on cooling, which correspond to the volume distribution of tin and tell nothing about the nucleus type. In any real alloy both effects will be combined, and it seems impossible at present to distinguish between them. M. B. Bever—The thesis of this interesting paper is supported by a combination of positive and negative evidence. The authors have shown that under certain conditions a liquid phase may undercool, if it is dispersed in a thoroughly discontinuous manner throughout a solid matrix. They also found that undercooling

Jan 1, 1951

By E. D. Gardner

In 1954, the first year the award was conferred, Fred Searles, Jr., remarked, "The earlier years are the easiest." In this, the second year, it was easy to choose the outstanding mining engineer. Our conferee this year has been destined to mine. He comes from pioneer stock, and though a son of the American Revolution he is most proud that all four of his grandparents came to the Jordan River Valley of Utah the "first summer," which all Utahns will recognize as 1847. At the time of discovery of high-grade ore in Bingham, his grandfather, Archibald Gardner, had a crew of men getting out saw timber in the area. The first claim staked in Bingham Canyon was named the Jordan, and Bishop Gardner was the colocator of the claim as well as the man to record it.

Jan 4, 1955

By C. A. Eligwe, F. W. DeVries, A. E. Torma

This study is an investigation on using hydrogen peroxide for tank-leaching of uranium with sulfuric acid. The optimum sulfuric acid concentration was found to be 0.03 mole 11 -'for a 25% pulp density suspension. The order of reaction with respect to sulfuric acid concentration was found to be ns0.75. The best results vith hydrogen peroxide were obtained at a 4.64 molar ratio of 6202 to U in the ore. The order of reaction was found to be zero with respect to hydrogen peroxide concentration. The theoretical maximum rate effect of Hz02 on uranium extraction was derived as Vm = 8.15 x mole &-'min-'. The highest rate experimentally attained was 8.09 x mole kL'min-'. It was found that the uranium extrac- tion was not affected by the pulp density up to the 50% used in this study. However, the final yieldswere significantly higher (over 90%) for leaches carried out in the presence of Hz02 than (less than 90%) for leaches carried out in the absence of H202. The reaction was found to follow a first order course with respect to substrate concentration (pulp density) regardless of the presence of H202. The effect of temperature was more explicit at moderate tempetatures (30 to 55 C) than at lower (10 C) or at higher (70 C) temperatures. At this latter temperature an almost complete extraction was realized even without H202. The apparent activation energies were found to be AEa = 2.68 kJ mole-' in the absence of H202, 0.5 kJ mole-'with Hz02 at 40 C to 70 C. and 4.72 kJ mole-' with Hz02 at 10 C to 40 C. All these activation energy values suggested that the uranium extraction process is diffusion controlled regardless of the presence of H202. Further, the change in activation energy in the presence of Hz02 indicates the possibility of change in the reaction mechanisms at lower and higher temperatures.

Jan 1, 1980

By E. C. Pechin

THE Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

Jan 1, 1874

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-' have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.' Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967

By Edmund C. Pechin

The Lucy furnace, owned by Messrs. Carnegie, Kloman & Co., and located on the Alleghany River, on the outskirts of Pittsburgh, is a splendid modern furnace, 75 feet high, and 20 feet bosh. She had been working well on low grade ores of about 50 per cent., producing daily 68 to 75 tons. There was on stock 500 tons of Republic ore, one of the purest and best of the Lake Superior ores, averaging over 68 per cent. of iron, which had been procured for the purpose of making a trial for Bessemer iron. This was charged by itself, and Mr. Skelding, the founder, reports that he did not succeed in getting a single cast when it came down, before the furnace chilled from the hearth to the top of the boshes, some 25 feet. Every effort was made to save her, without avail, and the disagree-

By A. D. Hill, R. S. Schechter, M. P. Walsh, I. H. Silberberg, M. J. Humenick

There are many uranium deposits which are too deep, too poor in quality or too small in extent to be economically strip mined. It now appears that this uranium can be mined using in situ leaching processes. A number of field tests have been, are being or will be conducted to demonstrate the feasibility of In site leaching. Preliminary results are encouraging, but a major question concerns the restoration of the mine site, which is generally contained within an aquifer. It is necessary to ensure that the quality of the water is not adversely affected by the mining operation. One component of the lixiviant is necessarily a cation and, during the course of mining, the ion exchange sites of the minerals in the mine zone become saturated with this cation. Ammonium is the cation now commonly used. Clearly, any restoration procedure or question involving the rate of cation migration with the groundwater all necessarily involve the process of ion exchange coupled with flow in porous media. The equations describing this process are presented in this paper and numerical solutions obtained. Preliminary results showing the effect of isotherm shape, cation exchange capacity, flow and dispersion are presented. These results demonstrate that in many situations cation migration in ground water will be slow.

Jan 1, 1979

By B. M. Larsen

ATTEMPTING to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic " and " macroscopic," depending on whether the variations in concentration of solutes? or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also underly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all segregation effects. UNDERCOOLING AND NUCLEI FORMATION It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus tempera¬ture. In practical terms this means that the nuclei number increases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. TEMPERATURE GRADIENTS AND HEAT DISSIPATION DURING FREEZING Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period: Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1944

INTRODUCTION TO MINERAL INVENTORY The first explanations to be made must answer the questions: What is a mineral inventory, and how is a mineral inventory different from an ore reserve? The term mineral inventory is a relatively new designation-born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral inventory makes no presumptions about the mineability of the blocks or their cutoff grade. Such parameters are implied with the use of the term ore reserve. Ore has a specific definition (see Chapter 1) and ore reserve must reflect that definition and thus has economic and mining constraints. An ore reserve will be different under different economic and mining conditions and is subject to reclassification by many factors. The term mineral inventory avoids all such ambiguities. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks. Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral inventory is an excellent designation for describing mineral value distribution within a deposit's geological setting. The techniques for assigning values and tonnage to mineral blocks or panels are the subjects of this chapter. Whether a summation of the blocks be called a mineral inventory or mineral reserve is not important. Many conventional methods for computing reserves of minerals refer to the methods in terms of ore reserve calculations. OBJECTIVES OF MINERAL INVENTORY OR RESERVES Mineral inventories are computed for the purpose of determining the quantity, the quality or value, and the spatial distribution of potentially economic minerals within the earth. Such computations are made at all stages in the life of a mineral extraction process, from the early exploration phase to the final year in the life of a mine. To quote Popoff (1966, p. 2), "They are the most responsible and irreplaceable tasks in the valuation of a mineral deposit. Efficiency in extraction and productiveness is impossible without accurate reserve computations." The accuracy of estimate required for each of the three parameters of quantity, value, and location is dependent upon the objective for which the reserve estimate is being made. Again quoting Popoff (1966, p. 2): Reserves are computed to determine the extent of exploration and development; distribution of values; annual output; probable and possible productive life of the mine; method of extraction and plan design; improvements in extraction, treatment, and processing; and requirements for capital, equipment, labor, power, and materials. Such computations are used to assist development

Jan 1, 1980

By H. H. Hausner, H. S. Kalish

M. Hansen—This paper certainly is an interesting study. Although I have not had too much experience in the powder metallurgical methods of studying phase equilibria, I would like to say the following concerning the interpretations of the results obtained: 1. The existence of a zirconium-rich eutectic having a melting point close to 950°C and containing approximately 5 pct beryllium is well established. 2. Undoubtedly sintering of the original compacts (i.e., without repressing and resintering at 1350°C) resulted in a condition being far from equilibrium, even in the low-melting point zircon-rich region where undissolved zirconium particles have been observed. This means that only partial reaction between the component powders has taken place. 3. In preparing and handling powder mixtures for pressing and sintering, we have found that with powders differing considerably in density, and also in particle size, separation in layers of different composition may occur. This means that a concentration gradient would exist within such samples. This phenomenon may, at least to some extent, account for the difference in microstructure of the top and bottom regions of some of the sintered samples. If this is the case, density figures for some of the nominal compositions would not represent actual densities of those mixtures. 4. Fig. 1 shows that the low densities of mixtures with 40 and 60 pct beryllium sintered at 1350°C are changed to much higher densities if the products sintered at 1100°C are repressed and resintered at 1350°C, whereby an approach toward equilibrium takes place. This would mean that the low density and growth in volume is due to nonequilibrium conditions. If this is true, would it be justified, then, to conclude that "the remarkable growth of the alloys in the vicinity of 40 to 60 pct Be indicates the formation of a high-melting point phase, probably accompanied by a considerable change in volume due to a large alteration of the crystal structure from that of the original compounds"? If some compound formation has taken place already during the first sintering at 950" to 1350°C, more compound would be formed by repressing and re-sintering of the 1100" samples. This treatment, however, results in higher, rather than lower, densities. In general, the density-composition curve of alloy systems containing one or more intermediate phases is characterized by a more or less defined contraction (decrease in specific volume, increase in density) over the "theoretical" density. Does not discrepancy exist between the two statements that "growth of the alloy indicates the formation of a high-melting phase . . ." and "even at 1350°C, no indications of sintering have been observed"? 5. I am not sure that the explanation given for the fact that fig. 4 did not reveal as much eutectic as the top portions of the mixture with 2 pct Be, is correct. The density of the melt containing only 5 pct Be or even perhaps less, is not too much different from that of the nominal composition. The reason might be also that there was already some separation of the components in the pressed compact. 6. I do not understand why the microstructure of the bottom regions of the compact with 5 pct Be (fig. 6) is so different from that of the top regions (fig. 5). The compact was melted on sintering at 1100°C. Its composition lies close to the eutectic point. There should be at least some lamellar structure in the bottom regions too; otherwise, the composition of top and bottom must have been very different after sintering, because the eutectic is said to extend as far as the composition ZrBe2. In case the white and gray areas of fig. 6 are both gamma, and the black areas undissolved zirconium, this composition would be close to the phase coexisting with zirconium, that is, ZrBe2, according to the hypothetical diagram, or a compound richer in zirconium. 7. Figs. 9 and 10 are not mentioned in the text. 8. The great difference in microstructure of the composition 20 pct Be of figs. 8 and 14 on one side and fig. 15 on the other side proves that sintering at 950" and 1100°C results only in partial reaction of the powers. 9. The mixture with 60 pct Be (fig. 19) seems to consist of two phases, rather than one phase, one interspersed in a matrix of another. 10. The statement that the eta phase "may be an intermetallic compound or the product of a peritectic or monotectic reaction" seems to be misleading, because the product of a peritectic or monotectic reaction in this region of the system must be an intermetallic compound. 11. If there is some solid solubility of Be in alpha and beta-Zr, it would be expected to be higher in beta-Zr (b.c.c.) than in alpha-Zr (h.c.p.). The temperature of the polymorphic transformation of zirconium then would be lowered, rather than increased. In accordance with this, Battelle has found that the transformation point of titanium is decreased by beryllium. 12. In case the phases present in alloys with 80, 90, and 95 pct Be are identical (which appears to be correct), it is striking that the relative amounts of both phases (eta and beryllium) are not too different within this wide range of composition. With 60 to 65 pct Be

Jan 1, 1951

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74' and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By Douglas R. Cook

The discovery of the gold deposits of the Jerritt Canyon district, with proven recoverable reserves in excess of 67.6 Mg (2.4 million oz) of gold, has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell mine, is a 70130 joint venture between Freeport Gold Co. and FMC Gold Corp., both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan Inc. and FMC Corp. The Jerritt Canyon district is located in the center of the Independence Mountains in north-central Elko County, Nevada, approximately 48 km (30 miles) northeast of the Carlin gold mine and 68 km (42 miles) north of Elko. Although the discovery of a commercial gold mine at Jerritt resulted from Freeport's exploration activities, the initial identification of a gold prospect in this area was a consequence of a program by FMC in the search for antimony. Their program was, in part, based on data in the Nevada Bureau of Mines Bulletin 61, "Antimony Deposits in Nevada." Work on the property began in 197 1 with geologic mapping followed by sampling and geochemical analyses. FMC geologists, including Robert Hawkins, Russell Hayden, and Hal Hurst recognized the striking similarity of the area to the geologic environment of Newmont's nearby Carlin gold deposit and soon focused on the gold potential. Increases in the price of gold served to stimulate interest and support for the exploration program. Geochemical samples were collected and analyzed for gold and trace elements usually associated with gold. A strong gold anomaly was found on the North Fork of Jerritt Canyon, which was called the Alchem anomaly. Drill-testing of this anomaly in 1973 revealed significant grades and thicknesses of gold mineralization in the lower portion of the Roberts Mountain formation. This initial discovery and subsequent close-spaced drilling proved the existence of several small pods of low-grade, gold-bearing material which cropped out at their up-dip edges, causing the surface anomaly. The mineralization was very encouraging, but was not, by itself, of economic importance from the standpoint of either grade or tonnage. Freeport Exploration Co. established a district office in Reno in late 1974 with responsibilities for exploration of hard minerals in the Basin and Range Province. Emphasis of the program was directed to the discovery of precious metal deposits. Enfield Bell, as District Manager for this new office, was particularly interested in the Independence Mountains and when the opportunity for a joint venture with FMC became available in 1976, it was aggressively pursued. Enfield Bell and David Stevens evaluated the FMC data and with the support of management formulated a bid in competition with 23 other companies. Freeport was selected by FMC as partner and a joint venture agreement was successfully negotiated. In mid-summer of 1976, Freeport Exploration Co. began an expanded program of detailed mapping and geochemical sampling under the direction of Bell and Stevens that led to new interpretations of the structural and alteration patterns. Hawkins' contribution during this period must be recognized since he not only was one of the original geologists assigned to the antimony and subsequently the gold investigations, but shortly after the start of the joint venture exploration, he was hired by Freeport Exploration Co. as the project geologist for the venture. Hawkins had studied the central Independence Mountains for his thesis and his understanding of the regional geology provided an excellent background for the continued exploration of the gold de- posits. His interpretation of the structure in the vicinity of the Alchem anomaly was of significant help in the Freeport exploration program. Drilling, based on this new under- standing of the geology, revealed the edge of the Marlboro Canyon ore body, which is now being exploited in the Bell mine. Although a classic bullseye geochemical target led to the discovery of the Alchem mineralization, the bulk of the reserves known today in the Marlboro Canyon area lay

Jan 1, 1985

By E. J. Bartosh

In the brief period from November 1936 to September 1937, the Wilmington oil field developed far beyond all expectations. Decline in some wells appears very rapid, but it is too early to draw definite conclusions, as the majority of wells are maintaining very large and steady output. Heavy curtailment in the central area, which has developed the largest wells, makes it impossible to arrive at a satisfactory estimate of decline. The field is producing oil from the Repetto (lower Pliocene) and Puente (upper Miocene) formations, which are of the same age as formations producing at Torrance, El Segundo, del Rey or the marginal fields of the Los Angeles Basin. All of these fields are underlain by schist. The Long Beach field, northeast of Wilmington, is productive throughout 3000 ft. of Repetto-Pliocene series and also approximately 3000 ft. of Miocene formations, whereas at Wilmington only 700 to 800 ft. of Repetto and 2500 ft. of Miocene formations contain oil and gas. This paper gives a brief summary of the history and development of the field to Sept. 15, 1937, showing the subsurface conditions as they exist with the field only partly developed. History of Development The Wilmington oil field, 20 miles due south of Los Angeles, adjacent to Los Angeles harbor and about midway between the cities of San Pedro and Long Beach (Fig. 7), was producing oil as early as 1932 and only came into prominence as a major oil field of Southern California in the fall of 1936, when the General Petroleum Corporation of California completed Terminal well No. 1 from the upper Miocene, at a depth of 3625 ft., for a daily production of 1500 bbl., 20" gravity A.P.I., thereby establishing discovery of the Terminal zone. As early as 1925, or during the close of the development of Torrance oil field, a number of wells were drilled in the Main Street area looking for

Jan 1, 1938

By E. T. Dumble

The domes of the Texas coastal plain are structural features, consisting of bosses or stocks of salt, gypsum or anhydrite, or of combinations of these, intruding into and occurring in connection with broken and uplifted sedimentary beds of Cretaceous and Tertiary age. Some of these domes show on the surface as mounds of greater or less elevation, while others are only known from drilling records. They may be divided into two classes: interior domes and coastal domes. The interior domes include those which occur in a zone 40 to 50 miles in width lying immediately east of the Cretaceous-Tertiary contact, and extending from the Sabine to the Colorado. With a single exception, these domes, so far as now known, occur in approximate alignment with the contact, but at irregular intervals. East of the Brazos, the domes are entirely surrounded by Eocene sediments. The coastal domes are found nearer the Gulf, lying entirely within Neocene territory and stretching from the Rio Grande to the Sabine. They are much more numerous than the interior domes, and, apparently, are ranged along several lines having a general northeast-southwest direction. No domes are known in the Oligocene belt. INTERIOR DOMES The interior domes so far, identified are Butler's, in Leon county, Palestine and Keechi in Anderson county, Brooks and Steen in Smith county, and Grand Saline in Van Zandt. In connection with these interior domes we must also consider the Sabine Peninsula,. of Harris, which is, without question, genetically connected with them. The Palestine and Keechi domes have been described recently by 0. B. Hopkins,1 who gives a clear idea of their corn position and structure. Others have been described at different times, and an excellent resume of the literature is given by De Golyer.2 _

Jan 10, 1918

By A. F. Meger

Coal treatment by oil spraying receives special attention at the Georgetown plant for the dividends it pays in satisfying present customers and attracting new markets. Customer satisfaction requires care, quality control, and use of suitable oils. REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal CO. who have helped develop, over a number of years, an efficient and flexible method for spraying controlled amounts of oil on coal. Since the Georgetown preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage. The graph, Fig. 1, shows results of the original tests made with a 700-sec residual blend and a 500-sec lubricating oil on Georgetown stoker coal of 1¼x3/8-in. size.* The advantages of better price, improperly blended can raise havoc. Some.,pale oils also, although odorless when delivered, give off a sweet sickening odor when atomized under pressure. It is recommended that all products be tested before they are used. There is a specific place for all spraying oils. For example, at a power plant a severe dust condition exists around the stockpile area and in parts of the plant. The cheapest spraying oil made, regardless of odor, will do an excellent job in this case and will save the company 3 to 5c per gal or more. Domestic trade, on the other hand, must be carefully handled to prevent complaints about odor, and the only way to do this is to stay with the proved products after the odor tests have been made. The preparation plant at Georgetown has facilities to handle either tank car or tank truck deliveries. Steam is available at the unloading point if the weather is severe, and there is an indicator at the unloading point to prevent overflowing the 20,000-gal underground storage tank. Systematic test samples are removed from each delivery and sent to the lubrication engineer to insure quality control. Fig. 3 illustrates the chutes in which smaller sizes of coal are treated. Fig. 4 shows the entire spraying system. Buried in the ground is a 20,000-gal tank with immersion heaters grouped around the feeder line to insure adequate gravity flow to the pump under all conditions of weather. Oil flows to a 500-gal preheating tank where the temperature is kept about 150°F by six 1½-kw immersion heaters thermostatically controlled. Hot oil is fed through a self-cleaning disc-type filter to the hydraulic pump. Valves and piping make it possible to transfer oil from one tank to another or to drain the lines for maintenance purposes. All this equipment is below ground level in a covered pump room,

Jan 1, 1955