Search Documents

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By Thomas M. Drown

At the meeting of the Istitote in New York, in February, 1880," I described a process of determining sulphur iu metallic allphides, with especial reference to the determination of pyrites in coal. The procem, as then described, is as follows: A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromiue is used it must be neutralized by the addition of a little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.e. of this solution autl heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then

Jan 1, 1881

By Fred T. Greene

(San Francisco Meeting, September, 1915) MOST of. the recent discussion of the mineral land law published in the Transactions is in the abstract-an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversy,1 which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has. called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the least of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the " Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40° W., clipping about 40° to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80° W. and clips at high angles to the north and south.

Jan 5, 1915

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By M. G. Driessen

For a number of years the cyclone, familiar to Americans as a dust collector, has been used as a thickener of suspensions at one of the coal-preparation plants of the Netherland State Mines in Limburg. The plant treats nut-size coal at 120 tons an hour in a heavy-medium washer. The diluted medium from the rinsing screens is thickened in cyclones. More recently the cyclone has been adapted to act as a coal cleaner. The principle of the cyclone thickener is the same as that of the cyclones used in industry for catching dust or fine particles suspended in the air or in gases. Generally the latter are more efficient in this respect—the smallest particles that can be caught with reasonable efficiency are considerably smaller than with the cyclone thickeners. The reason is obvious; the ratio of specific gravities between the dust particles in a gas and the gas itself is about 800 times larger than the ratio between, for instance, the specific gravities of shale particles and water. The ratio of the velocities of fall of shale particles (? = 2.5)† in air and in water is as follows: In the range of Stokes: ?air = 93?water In the range of Allen: Wair = 49Wwater In the range of Newton-Rittinger: ?air = 36.6?water The same ratios apply for the velocities in the centrifugal field, from which it follows that it is especially difficult to catch the very fine suspension particles in a liquid. The efficiency of a cyclone thickener depends mainly on the circumferential velocity of the liquid at its innermost radius, because here the centrifugal forces are the highest. However, these velocities cannot easily be calculated, as the flow is three-dimensional, and thus the axial components cannot be neglected .(p. 252, condition 3). We believe that at first a spiral tangential motion along the cyclone wall is created, which causes the inner vortex ascending from the apex of the cyclone (Fig I). At the same time the inner vortex is strengthened by the individual vortices in horizontal planes, and thus a part of the total flow can find another and perhaps quicker way to the outlet. In any case, the exact motion, not only of the fluid but especially of the suspended particles, is so difficult that we have to refer to the experiments to find the exact behavior of this kind of apparatus. Method of Judging PerforMance of Coal Washer Geologists, rather than mechanical en-gineers, would be able to describe the separating or stratifying effect in nature, but even a bather on the shore lying on the soft sand near the sea wonders why all the small sand grains have approximately the same size. A child playing on the border of the river could easily

Jan 1, 1949

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By W. R. Hibbard

Although extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110) , [111] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampton5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr in a standard mer-curous nitrate test. Edmunds12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wasserman11 reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. Preparation OF Specimens Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5, 10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. Determination of Pole Figures A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pet nitric acid to 0.0015 in. thickness and (111) pole figures were determined using copper K-alpha radiation in the manner described by Brick.' The three general types of pole figures

Jan 1, 1949

By Clarence A. Seyler

The technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter' published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution, having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and camels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 C.C. of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 1, 1925

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the Inter-national Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information avail-able regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which, more exhaustive experimental work may be clone to best advantage.

Jan 1, 1938

(Under this heading will he published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, mining engineer, technical education with 9 years' varied experience as superintendent and operating engineer, desires position with mining or manufacturing company requiring the services

Jan 3, 1918

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By C. F. Riisness, E. R. Parker

THAT grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in [ ] determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size 4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, [ ] however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandford10 and Pell-Walpole,11 in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the. creep rate: At high temperatures, generally a coarse-grained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By G. Austin Schroter, Ian Campbell

ALTHOUGH there is now an extensive literature on the bleaching clays, not a great deal of material is to be found concerning the geological features of these deposits and their bearing on problems of exploration and development. At the same time, chemical and crystallographic research on the clay minerals during the past few years has laid a suitable foundation upon which to base conclusions of economic value drawn from field observations. All of the criteria and deductions herein presented are based upon extensive field work by the senior author, both in the United States and Canada, and when subjected to the ultimate tests of development and exploitation they have held up remarkably well, despite the fact that many of these conclusions apparently have not been reviewed in the literature heretofore. The nomenclature of the bleaching clays is rather confusing in the light of present-day commercial standards and has even led to litigation." The old term "fuller's earth" is largely based upon trade usage and the definition of the term therefore is dependent upon the changing standards of commerce. For statistical purposes the Bureau of Mines81 classes as "fuller's earth" all natural bleaching or filtering claylike materials that possess high adsorptive capacity without previous chemical treatmerit or activation. Conversely, the so-called activated or acid activated clays are now generally recognized as any clay mineral or mixture of the clay minerals whose adsorptive capacity has been developed to commercial standards by chemical or physical treatment. Therefore, without attempting to propose any additions to the nomenclature of bleaching clays, this paper will refer to naturally adsorptive clays and activable clays, respectively, for the two types indicated.

Jan 1, 1940

George IV. Goetz, Milwaukee, Wis.: Mr. Campbell deserves much credit for his interesting paper. The literature of the development of the open-hearth process is distributed in many technical journals, and is difficult of access to many engineers. Since the development of the basic process, the open-hearth furnace has been raised from a subsidiary to an independent position. Certain high grades of soft steel can be produced in the basic open-hearth furnace, which cannot be produced by any other known process. In the United States the charges for the acid process generally consist of either scrap and pig-iron or so-called wash-metal and scrap : the pig-and-ore process, as carried out in England, is practiced but very little. The introduction of the basic process has made it possible to use about four times as much pig-iron with scrap as can be used in the acid mixtures. The availability of a cheap pig-iron, very low in silicon and sulphur, and carrying several per cent. of manganese, is one of the reasons why the basic open-hearth process has developed so rapidly in Germany, as regards the output per furnace and the excellent quality of the material produced. The acid Bessemer steel has an inherent stiffness, which is plainly shown when spring steel is made by the Bessemer and by the openhearth processes. In order to get them of about equal stiffness, the open-hearth steel must have about 0.60 per cent. carbon ; whereas, the Bessemer steel must then have ahout 0.45 carbon, the remaining constituents being apparently about the same in each product. It has proved impracticable, with American coke-pig-iron, to interrupt blowing at a certain point in order to make hard steel; and experience has therefore shown that it is best to eliminate nearly all the carbon, and then to recarburize to the desired point. This practice

Jan 1, 1894

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. R. Parker, C. F. Riisness

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By C. F. Riisness, E. R. Parker

That grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandfordl0 and Pell-Walpole,ll in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the creep rate. At high temperatures, generally a coarsegrained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By P. E. McKinney

Developments in engineering during the past decade, particularly as applied to marine construction, mining machinery and other purposes in which corrosion offers a serious problem, have created a large demand for a non-ferrous metal highly resistant to corrosion and at the same time useful in general construction work as a substitute for steel without materially decreasing the factor of safety or increasing the weight of the various parts over that ordinarily used in the case of mild steel. To obtain the combination of desired properties many compositions have been proposed and used with excellent success, but at the present time probably the most popular and most widely used combination is the non-ferrous alloy commonly called manganese bronze. This is nothing more than a high brass to which have been added, by the proper method of alloying, comparatively small percentages of aluminum, iron, or manganese with the definite purpose in view of strengthening the alloy and rendering it more dense and close-grained than the average yellow-brass casting. In the manufacture of manganese bronze a great deal has been said about the importance of using only the highest grades of raw material and the beneficial or detrimental effects, as the case may be, of various impurities, as well as the importance of adding the ingredients according to various formulas proposed; but in most of these cases the literature on the subject has dealt principally with the manufacture of this alloy from virgin metals and raw materials of the highest purity. It is the purpose of this paper to deal particularly with the possibilities that lie in the proper development of methods for manufacturing such an alloy by more economical methods than those which have usually been discussed in other literature on the subject. Shortages have recently existed in raw materials needed for many products entering into the various branches of engineering work, particularly the non-ferrous metals, and during the next few years of reconstruction the country will be flooded with many

Jan 1, 1919