Search Documents

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By G. B. Walker, S. J. Swainson, S. A. Falconer

DURING the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad -are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue Of MINING AND METALLURGY, Professor Taggart made the statement that "preconcentration by heavy suspension was Miss A.I.M.E. 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By Louis Katona

The practical execution of the design for rolling-mills presented by the writer at the Paris meeting* of thc Iron and Steel Institute in 1900 involves the determination of some questions not yet discussed, among which is the determinatioir of the amount of power required to perform the rolling of pieces of iron and steel of given dimensions. It is necessary to know this factor if we would put motors of proper capacity to the respective pairs of rolls, or, rcciprocally, if, having standard motors at our disposal, we would design grooves to suit them. Moreover, this factor is involved in giving right dimensions to every part of the rolls and housings. Expert designers of engines for driving rolling-mills of the present type receive very indefinite directions, such as: that the motor is to drive a light, medium or heavy train; that it must work with fly-wheel or reversing gear; that the number of revolutions per minute should not exceed 40 or 60, and that at a given speed the power developed should be from 100 to 200 H. P., or from 1,000 to 2,500 13. P. It frequently happens, however, that an cngine of 200 H. P. is forced under the circumstances to press or develop as much as 300 H. P., while, on the other hand, the ,1,500-11. P. engine may be rolling-stock which could be worked with a maximum expenditure of 60 to 80 H. P. Of course such variatior~s as these do not permit the best adjustment of parts or the best economy of power and fuel. The design of roll-trains is even more vaguely limited. Every part of a train, from the point where it connects with the engine to the last groove in the rolls, bears evidence that there are no rules for calculating even approximately the dimensions of the main-shafts, couplings, pinions, gears, rolls, trunnions,

Jan 1, 1904

By Milton E. Jennings

On May 11, 1977, the SAMARCO 508-mm (20-in.), 396-km pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO project. This paper presents the background, description, and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1982

By A. M. Gaudin

CHANGES in industrial practice, in plant design, and in research methods which are so clearly to be seen on every hand, have affected the mineral industry as well as others. In particular, ore dressing has passed through a revolution in practice brought about by the introduction of flotation and other quasi-chemical methods, until it has ceased to be solely the mechanical preparation of ores. In fact, the term "ore dressing" itself is obsolescent, and "mineral dressing" has been growing in popularity. This assures adequate recognition of the fact that mineral substances other than ores, e.g. coals, clays, and cement rock, are treated by the same general methods. As a result of these industrial changes it was felt that a complete rearrangement of the curriculum and laboratories at the Massachusetts Institute of Technology would be ad-vantageous. Such a rearrangement would allow instruction and research to proceed in wider accord with industrial evolution and the needs of our times.

Jan 1, 1942

By H. W. Miller, V. H. Wilhelm

During 1932 the oil industry persistently endeavored to maintain a rate of production that would permit a profitable price structure. Much effort was concentrated on curtailment of both production and drilling. The tendency in curtailment was to shut in reserves where closely held and not subjected to drainage, and to allow town-lot fields such as Long Beach, Santa Fe Springs, Playa Del Rey and Huntington Beach a greater percentage of allotment. Marginal wells were given special consideration; only a small percentage of curtailment wag required, making their operations profitable. Naturally the decline in production of town-lot fields, under slight curtailment, is very rapid, hence production that is restricted in fields controlled by major interests at the present time will profit considerably in the future, as California reserves do not appear adequate to sustain heavy withdrawals over a long period of time. California production during 1932 was much greater than additions to reserves during the year. The state produced 10,701,238 bbl. of crude oil less in 1932 than in 1931, while total stocks (all petroleum commodities) decreased 1,589,524 bbl. Had all operators kept strictly within their allotted 'production, the total crude production decline would have been approximately 20,000,000 bbl. and total stock decrease 3,000,000 barrels. Estimated proven oil reserves for California were 3,965,000,000 bbl. on Jan. 1, 1932, as compared with 3,784,120,000 bbl. as of Jan. 1, 1933, a decrease of 180,880,000 barrels. Approximately 85 per cent of the 178,127,794 bbl. of oil produced during 1932 was withdrawn from old reserves in settled fields and the remaining 15 per cent from new sources such as Kettleman Hills North Dome, Belridge, San Miguelito and Dominguez deep zone. The oil reserves of Kettleman Hills North Dome are estimated to be approximately 50 per cent of the total oil reserves, of California and they may be drawn upon at a much greater rate than the remainder of the state's oil fields.

Jan 1, 1933

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to in¬crease the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1944

Charles R. Eeyes, Des Moines, Ia. (con~munication to the Secretary*):—It is not in a spirit of criticism that I offer a supplemental suggestion or two on the subjects covered by this valuable and highly instructive memoir. There are two points which, in my opinion, should have received greater emphasis in Mr. Emmons's excellent paper. One is the fundamental r6le played by the chlorides under certain conditions in ore-formation. The other is the possible establishment of geographic relationships among the four pheilomena of (1) excessive chlo-ridic content of mine-waters; (2) the abundance of chloridic compounds of the precious metals; (3) the presence of man-gancse oxides; and (4) the diminishing importance, in ore-genesis, of the metallic sulphates. Although Mr. Emmons's notes refer to gold alone, it may be pertinently asked whether the same principles do not hold good for silver and copper also, since these metals form, together with gold, a distinct and well-known chemical group. That the reactions involved apply equally well to the other two metals mentioned, is sbown by a number of recent observations and discussions. Chloridic ores of silver are, as I have lately endeavored to show, mainly worked in arid or desert regions only; and the great deposits of disseminated copper-ores are similarly characteristic of such regions, in which both classes doubtless owe their formation to the abundance of saline materials derived from desert dusts, and to the plentiful and almost universal presence of manganese oxide. Under these climatic conditions, silver is somewhat more abundantly deposited than copper and gold, because its chloride is so much less soluble. During volcanic emanations, the metallic chlorides perform at all times distinct functions; when these are

Jan 1, 1912

The regular activities of the Insti¬tute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to in¬crease the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1942

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By Heinrich 0. Hofman

A T THE meeting of the Board of Directors on June 24, Prof. Heinrich O. Hofman was elected an honorary member of the American Institute of Mining and Metallurgical Engineers. Professor Hofman is best known to the world at large for his publications, and in this respect he is to this generation what Schnabel was to the previous one. The first edition of Professor Hofman's "Metallurgy of Lead and Desilverization of Base Bullion"; was published in 1893; the fifth edition in 1898. In 1913, he published his work on "General Metallurgy;" this was followed by "Metallurgy of Copper" in 1914, and a revised and enlarged edition of the "Metallurgy of Lead" in 1918. "Metallurgy of Zinc and Cadmium" is now in press. He also published, through the Massachusetts Institute of Technology, "An Outline of the Metallurgy of Iron and Steel" for students' use. Since the founding of "Mineral Industry" in 1892, he has been continuously the annual contributor on the metallurgy of lead, and all Institute members know that his contributions to the TRANSACTIONS have been liberal in the extreme. It is through this medium that the results of the extensive research work, which he has always carried on in connection with his work at the Massachusetts Institute of Technology, have been published. Of the greatest importance are his papers dealing with the formation temperatures of slags, but many other metallurgical subjects have been covered.

Jan 1, 1921

By John A. Wolfe

The brightest spot in the mineral economy of the Philippines is the rapid development of reserves and production of copper. If economic conditions remain favorable and the political climate is encouraging, production of this metal should increase at a rate of 25% per year for several years, long enough to rank this country as one of the major copper producers of the world. In 1965 the copper content of the Philippine concentrates was approximately 60,000 tons. It should total about 80,000 tons in 1966. A major part of the increase will come from the rich Lepanto mine located in Mountain Province, North Central Luzon. Daily production of ore increased from 1200 to 2000 tons at the end of 1965. The ore, consisting of enargite and luzonite, averages nearly 3% copper and 0.12 oz. of gold per ton. It is an under- ground operation with a cutoff grade of 2%. The ore is associated with extensive silicification under a volcanic cap rock. Further expansion to increase ore production to 2600 tpd is under way.

Jan 4, 1967

By J. J. Gilvarry

Recently, Gilvarry1,2 has given a rigorous derivation of the proper distribution function for fragment size in single fracture, based on a closely defined physical model and deduced strictly by the laws of probability. The physical point of departure is Griffith's theory of brittle strength, identifying sub-microscopic flaws as the cause of the low strength of a solid in comparison with values implied by cohesive energies. Gilvarry and Bergstrom,4-7 and Gilvarry8 have compared the predictions of the theory with experiment, and have found excellent agreement, in general. The purpose of this communication is to sketch the extension of the theory to the case of comminution, and to indicate the applications to some examples in nature. The present treatment represents an amplification of a brief discussion appearing elsewhere. 9 Although the basic ideas of the Griffith theory are perfectly general for rupture of brittle solids, it was originally formulated with very brittle materials such as glass in mind. Moreover, Griffith's original experimental work was carried out on glass specimens. Recently, however, the theory has been extended by race" to apply directly to rocks. This extension makes the theory immediately applicable to the materials generally of interest from the standpoint of comminution. GENERAL CASE To obtain the distribution function for fragment size in single fracture, three assumptions are made, that: 1) Fracture proceeds by activation of preex-istent Griffith flaws in the volume, faces, and edges of a fragment; 2) the distributions of flaws of these three types are independent of each other; and 3) activated flaws of a particular type are distributed at random, individually and collectively, in the sense of Fry.11 The last assumption implies that each distribution is separately of Poisson type.

Jan 1, 1964

By E. J. Koval

Practical miscible displacement processes will be characterized by lingering of the solvent into the oil. The lingering process is brought on by viscosity differences, and can be accentuated by channeling and longitudinal dispersion. The effects of these factors on the efficiency of unstable completely miscible displacements are combined in what is called the K-factor method. This method, analogous to the Buckley-Leverett method, predicts recovery and solvent cut as a function of pore volumes of solvent injected. Experimental data are included and show excellent agreement with theory for a wide variety of sandstone cores and viscosity ratios. INTRODUCTION Theoretical considerations,1 laboratory experiments,2 and pilot tests3 lead to the conclusion that miscible displacements in the field will be unstable In an unstable miscible displacement, the solvent fingers through the oil. This fingering leads to early breakthrough of the solvent and an extended period during which both oil and solvent are produced. For such a system, there appear to be four principal factors which bring about or accentuate the effects of instability: longitudinal dispersion (including geometrical effects), channeling, viscosity differences and gravity differences. Other factors, such as diffusion and flooding rate, can also influence the effects of instability, but at the flooding rates considered in this report, circa 15 ft/D, they are unimportant. Longitudinal dispersion can be thought of as a spreading of the solvent front caused by the presence of microscopic inhomogeneities. Channeling of the solvent occurs when a porous medium has macroscopic inhomogeneities; i.e., gross permeability variations. Viscosity differences lead to fingering of the less viscous solvent. This difference in viscosity accelerates the growth of fingers along paths previously developed because of permeability variations. Gravity differences lead to overriding by the usually less dense solvent. Al- though gravity effects are generally small at a flooding rate of 15 ft/D, they would, nevertheless, unnecessarily complicate the interpretation of flooding experiments. For this reason, all the experiments reported herein were done with matched density fluids. Fingering and the resultant poor areal sweep were recognized early as the dominant influences on the efficiency and the economics of miscible displacement processes. Much research effort has been spent on ways to minimize fingering and increase areal sweep such as the use of graded viscosity slugs4 or water slugs. Some researchers attempted to work out ways to prevent fingering completely; i.e., to achieve a stable displacement through gravity or latitudinal dispersion stabilization. l Others did not attempt to control fingering but obtained an economic process by merely recycling the solvent and sweeping pattern by pattern.6 During this period, all aspects of fingering came under close scrutiny. Some researchers reported on how fingering looks2 and how it is affected by viscosity ratio,7 geometry,7 and slug size.2,* Peaceman and Rachfordg suggested a mathematical approach to the prediction of unstable miscible displacements in relatively homogeneous sand packs, but their work cannot be extended conveniently to heterogeneous systems. Hence for a heterogeneous system, no method is presently available for predicting solvent cut and recovery as functions of pore volumes of solvent injected. The purpose of this investigation was to attempt to fill in the gap in our knowledge concerning the prediction of performance of unstable miscible dis placements. Necessarily, the system selected for study was a relatively simple one. The restrictions placed on the system were: (1) The system was linear; (2) The solvent was miscible in all proportions with the oil in place; (3) The solvent was continuously injected into the porous medium; (4) Gravitational effects were eliminated by matching densities and (5) All the flood rates were high and constant at 15 ft/D to avoid any small rate effect and to minimize any diffusion effects. To simplify and to indicate that both longitudinal dispersion and channeling arise from permeability variations, the effects which they cause or influence have been termed heterogeneity effects. The use of

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By Norman Pilling

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. TIN is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper-i. e., copper containing from 0.03 to 0.10 per cent. of oxygen-apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 2, 1926

By P. Somasundaran, D. R. Nagaraj

Based on our finding that commercial copper chelating solvent extractants such as LIX65NR and LIX63R are excellent collectors for copper minerals, a detailed study was made using several water-soluble chelating agents belonging to the class of aromatic hydroxyoximes and having a gradual structural variation. A basic study of the system salicylaldoximetenorite was also carried out. Microflotation tests as a function of concentration of oxime, pH, addition of copper, etc., using oxidic copper minerals such as chrysocolla and tenorite, and batch laboratory flotation tests using synthetic mixtures of quartz and oxidic copper minerals were carried out. The results have demonstrated that the hydroxyoximes studied have comparable collector property, and in all cases the oxime was found to be partitioned between the mineral surface and the copper in the bulk aqueous phase in the form of a bulk copper chelate. The occurrence of the latter could be accounted for by formation in the bulk phase of a chelate between oxime and copper released from the mineral and/or by the detachment of the surface chelate. The role of surface and bulk chelates in flotation is discussed based on the results of partitioning of chelating agent into bulk and surface chelates in the salicylaldoxime-tenorite system. The effect of structural aspects such as isomerism and substitution in the molecule on the collector property of the oximes is also discussed. Substitution on oximic carbon by alkyl groups is found to promote collector activity. Only the anti-isomer has the ability to collect.

Jan 1, 1982

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By Clarence Seyler

THE technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter1 published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and cannels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened' with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 c.c of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 3, 1925

By S. Isserow

RECENTLY, a description of the wartime work in this laboratory on the U-Si phase diagram was published. This diagram was available earlier in the open literature; as were Zachariasen's crystal structure identifications for the compounds in the system. The uranium end of the phase diagram is shown in Fig. 1. The most recent work on this system has emphasized the peritectoid E phase, of particular interest for a number of reasons. The early work provided evidence of this phase's resistance to corrosion in water and of its slight ductility. Further information on these properties has been obtained here. Work elsewhere4 has provided evidence of stability under irradiation. This body-centered-tetragonal phase is relatively isotropic compared to the more usually applied a or ? uranium phases. Unlike the other compounds in this system, it contains no Si-Si covalent bonds.3 In addition, consideration on the basis of Pauling's concepts leads to the conclusion that in the E phase, uranium has a higher valence than in any of the other phases. Definition of the composition of the ? phase has been of prime concern in the study of this alloy. Evidence is presented below that its silicon content is slightly higher than that of stoichiometric U8Si, the composition frequently assigned this phase on the basis of Zachariasen's identification. This work on the composition required careful attention to the method of dissolving the alloy for analysis, since apparently low silicon contents could be found under certain conditions, see Appendix. Preparation: Melting, Casting, and Heat Treatment—Almost all the samples were from castings with a diameter of 13/4 or 2 in. and about 1 ft long, weighing 10 to 15 lb. The U-Si charge was melted by heating to about 1650°C in an induction heated vacuum furnace. Beryllia crucibles were used at first, but were replaced by zirconia-washed graphite as the technique of keeping the carbon content low enough (about 500 ppm) was mastered. The alloy was bottom-poured at about 1650°C into graphite molds. A few small buttons, weighing no more than 50 g, were prepared in a small arc melting unit.' Since cast material has a preponderance of uranium and U8Si2, heat treatment is necessary to ob-tain the ? phase by the solid-solid peritectoid reaetion. Once obtained, the ? phase is stable to room temperature, obviating the need for speeial attention to the method of cooling after epsilonization, see Fig. 1. It was found desirable to epsilonize at 800°C for a week. For some purposes, in which residual uranium and/or U8Si2 are tolerable, shorter periods may be adequate. The temperature of 800°C is not critical, since essentially the same results were obtained from 785° to 825°C. Further departure from this epsilonization range is inadvisable.

Jan 1, 1958