Search Documents

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Harold Vance

The Lafitte field, the largest oil reserve in South Louisiana, is in Jefferson Parish, some 25 miles due south of the City of New Orleans. The discovery well, The Texas Company's No. I, Louisiana Land and Exploration Co., in the southeast corner of sec. 19, T. 17 S., R. 24 E., was completed on May 15, 1935. The initial production of this well was 960 bbl. of 34.9º A.P.I, gravity oil per day, through 1/4-in. choke, with a tubing pressure of 1600 lb. per sq. in. Producing depth was 9558 to 9572 ft., the total depth being 9572 feet. The development of the field has been at the rate of three to eight new producing wells per year. Up to Jan. I, 1944, 60 producing wells and three dry holes had been drilled, while two of the original producing wells had been abandoned, Although the field is not unitized, The Texas Company was the sole operator in the field until the Lafitte Oil Co. completed its NO. I Jefferson Parish, near the center of the west line of the NW/4 sec. 20, T. I7 S., R. 24 E., on July 27, 1941. No additional wells have been drilled by the Lafitte Oil Company. Drilling and WeLl-completion Practices All drilling operations have been conducted with the steam-driven rotary equipment mounted on submersible barges. A canal is dug to the well location and the drilling unit is floated into position. The seacocks are then opened and the barge settles to the bottom. After the well is completed, seacocks are closed and water is pumped out of the barge. This procedure permits the barge, with drilling equipment still in place, to be floated and moved off the location. The conventional open-hole and the gun-perforation method of completing wells has been used in this field. Where possible, the initial completion is from the deepest 'sand and recompletions are made progressively up the hole, by plugging back with cement to the upper sand and gun-perforating opposite the new sand. The oil string usually is 7 5/8 in., 26 to 34-lb. casing. Three wells have been completed using 9 5/8-in. 44-lb casing set below 10.000 feet. Fig. I shows the completion and recom-pletion practices on one well in the field. This figure also shows the relative locations of the different producing sands as shown on the electric well log. Structure The structure is an elongated dome, cut by two north-south faults, which divides the field into three segments. The west segment is the highest structurally and contains most of the recoverable oil and gas. The center segment is less important and the east segment is of little value. Figs. 2, 4, 6, 8 and 10 are depth contour maps on top of the five main producing sands in the field. These maps show the relative size of the five reservoirs and the

Jan 1, 1945

By James E. Hoffmann

This paper reviews the chemistry of selenium and its compounds as it applies to the recovery of selenium from electrolytic copper refinery slimes. Based on this chemistry various processes for the extraction and recovery of selenium from refinery slimes are explained and developed. The optimum selenium technology processes is dependent upon many factors including copper refinery location, environmental and regulatory conditions, local markets for selenium or selenium chemicals, and other plant processes. For this reason there is no one best process but rather a variety of useful processes for winning selenium. Those which have demonstrated consistent utility in both ease of recovery and reliability are discussed in more detail. Recovery of selenium by Doré furnacing of slimes is the topic of a separate paper. The companies that have developed selenium extraction technology are not being cited in this paper for the following reasons: o Their current technology may be different o The actual inventor of a process is difficult to credit since many different organizations have pursued parallel inquiries in developing better processes. Finally, some selenium extraction processes have been omitted; not because they are unworthy of consideration but rather due to limitations of space.

Jan 1, 1984

By Nigel B. Pearson

INTRODUCTION Chingola Division of Nchanga Consolidated Copper Mines Limited is situated in the Copper- belt of Zambia, approximately 30 kilometres south of the border with Zaire. It is the country's leading producer of copper and its principal foreign exchange earner, and has been, in its time, the largest single copper producer in the British Commonwealth and the second largest in the world. There are two 'primary' copper sources at the Division, namely Underground producing approximately 100 000 tonnes of contained copper annually, and the Open Pits, producing approximately 200 000 tonnes annually. Following the commissioning of the Tailings Leach Plant in 1974, treating final tailings, metallurgical recovery increased from approximately 70% to in excess of 80%. Extensive deposits of cobalt are present and following the rise in the market price in 1979 and 1980, plans were made to extract this separately. Cobalt production commenced in 1980 from Underground and will increase substantially when the Open Pit cobalt reserves become available in approximately 2 years time. This paper covers the development of the production method of the principal Underground Orebody, known as the Lower Orebody, and the control systems applied to it. HISTORY The Lower Orebody, formerly known as the Nchanga West Orebody, was discovered by extensive Diamond Drilling operations in the late 1920's. Development of the Shaft complex and the orebody commenced and continued until 1931 when flooding from development on the 480 foot horizon necessitated closure. The mine remained closed until 1937 and production commenced from the Lower Orebody in 1939. Various expansion schemes of the Metallurgical Plants and the Underground workings were completed over the years with the result that Underground production increased steadily to in excess of 150 000 tonnes copper annually in the 1960's. In recent years production has levelled out at slightly less than 100 000 tonnes annually. This decrease is as a result of producing from a lower grade reserve, available within a more limited production front, and the application of production constraints in the light of experience gained. GEOLOGY Within the Nchanga Mining Licence Area of Chingola Division, there are a total of 14 known copper orebodies in the basal part of a thick succession of sediments of Pre-Cambrian age. The sediments rest on a Basement Complex of granites, gneisses and schists. Three superimposed stratiform orebodies, known locally as the Lower, Intermediate and Upper Orebodies, occur over a vertical interval of approximately 150m. Current annual copper production is approximately 300 000 tonnes. The ore originates from four different mining operations, one Underground mine and three Open Pits. Approximately 9 million tonnes of ore grading between 3 and 3.5% copper are milled annually. The two largest sources of ore, the Under- ground mine and the Nchanga Open Pit are on the gently dipping south limb of the Nchanga Syncline (Figure 1). In the Nchanga Open Pit the major source of ore is the Upper Orebody with lesser tonnages from the Intermediate and Lower Orebodies. In the Underground mine the Lower Orebody is the only orebody being mined, underground mining of the Upper Orebody being suspended for economic reasons in 1978. The typical stratigraphic column is illust- rated in the legend on Figure 1. The footwall rocks comprise either Nchanga Red Granite or the Arkose formation, both of which are hard competent rocks, offering generally good mining conditions for footwall development. Copper mineralisation of the Lower Orebody extends from the upper part of the Arkose to the top of the Lower Banded Shales. Overlying the Arkose is the Transition zone (0-18111 in thickness). The Transition zone comprise a lower member, Transitional Arkose, consisting of incoherent kaolinised sandstone, and an upper member, Transitional Lower Banded Shales consisting of normally soft bleached and silicified shale. The soft nature of the Transitional rocks is

Jan 1, 1981

By I. N. Knapp

I Herewith present some notes on the use of Portland cement to cement in the casing, and for plugging, to exclude water from oil and gas wells, and the methods employed. I have used my best efforts to. make each step of the operation of cementing wells perfectly clear. The information is the result of actual experience and observation. The illustrations are from original drawings made especially for this paper. Portland Cement It is not necessary to discuss here the manufacture of cement. Any established brand of the slower setting Portland cements may be purchased with the confidence that it will harden, if properly used, and exclude water from and plug wells efficiently. Setting.—By the setting of cement is meant its initial change from a soft or plastic mortar to a friable solid. After the cement has become thoroughly set it is still very weak and can be readily pulverized in the fingers. Setting is thought to be effected by the crystallizing out of the silicate and the aluminate of lime, which are soluble in water in their anhydrous form. After dissolving in the water they pass to the hydrated state, in which they are insoluble, and hence are precipitated in a crystalline form. Ordinarily neat Portland cement mortar remains perfectly plastic for from 1 to 1 1/2 hr. after mixing with water at about 70" F. A higher temperature accelerates and a lower retards setting.. Hardening.—This is due to a continual crystallization of salts from solution, and to further chemical and physical changes which develop slowly, but which continue for long periods of time. Testing.—It is no more necessary for an operator to go into the scientific testing of cement to be used in a well than to so test the pipe used. He must depend for the quality of each on the tests and reliability of the manufacturer. Cement or pipe may be damaged in shipment so

Jan 1, 1915

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By M. G. Cheney

THE production record of the Sinclair-Moren pool, in southeast Young County, Texas, demonstrates that under efficient operating methods a single well may obtain normal oil recovery from an area of 100 acres or more. This record is the more surprising in view of relatively adverse reservoir conditions such as lack of water drive, moderate initial reservoir pressures and a consolidated sandstone reservoir with original permeability greatly reduced by processes of lithification. This case history is considered worthy of special study in view of the ever present problem of proper spacing of wells. Cupidity, abetted by the unrestrained law of capture, has in too many instances guided development and production methods without regard for sound economic and engineering principles. Largely as a result of ill advised spacing of wells, many oil fields have brought financial losses instead of deserved profit to those using capital, time and energy in this important business of adequately meeting the petroleum requirements of what is known as our modern civilization. In March 1923, the Sinclair Oil and Gas Co. obtained initial daily production of about 12,000,000 cu. ft. of gas and 1100 bbl. of oil in its first well near the center of a 372-acre lease on the L. P. Moren land, James Rose survey, Abstract 245. This exploratory test was drilled as a geological prospect of average promise, on a plunging anticline with possibly 10 ft. of closure as mapped on the outcropping limestone of upper Canyon (Pennsylvanian) age. In subsurface, the top of the producing res-ervoir is 16 ft. lower in this well than in the highest wells but probably 25 ft. above lowest closing contour. Wells No. 2 and 3 were drilled about 1/4 mile west and southwest near a normal fault with some 30 ft. of downthrow to the southwest. The producing sand was reached at a depth of 2512 ft. and drilled to 2529 ft. in the first well. This sandstone reservoir is of Millsap Lake (middle Strawn, upper Cherokee) age. It was absent in the second and third wells, which were abandoned at the depths of 3725 or more. In April 1925, a fourth well was drilled 600 ft. east and 24 ft. lower for top of sand than No. I. Production of about 100 bbl. daily was reported from 2521 to 2562 after an 80-quart shot. This well was drilled to 4560 ft., plugged back to 2575 and shot again; but was abandoned soon thereafter because of small production.

Jan 1, 1940

By J. R. Johanson

With the continuing development of automatic operations, it is important that reliable discharge rates through hoppers and bins be obtained for bulk solids. In most applications a feeder is used to control the feed rate. The selection of this feeder size is usually based on the rated ability of the feeder to move material without regard to the capability of the material to flow through the opening in the hopper onto the feeder. The dis charge rate through a given hopper opening may vary from zero to a theoretical maximum depending on the flow properties of the material. This paper presents an equation for the maximum discharge rate for a bulk material as a function of the hopper shape, the opening size and the flow properties of the material. Discharge-rate tests on various materials indicate good agreement with calculated values for opening sizes from a fraction of an inch to several feet. As part of a program to develop improved design criteria for bulk storage and handling facilities, a specific study of the methods involved in calculating the rate of discharge of bulk solids from hoppers and bins has been made. This study is closely related to earlier work done on the prevention of flow problems through the choice of proper design geometry of hoppers and bins1. The present paper is an extension of this earlier work, and therefore many of the concepts previously derived and explained will be used without explanation. Two types of flow will be considered: plane-strain flow in a wedge-shaped hopper and axial-symmetry flow in a conical hopper. The literature contains many studies on discharge rate for regular-shaped dry particles2*3 such as glass beads, lead shot and coarse dry sand. However, the work is empirical in nature, and it is difficult to extrapolate the given information to apply to moist, sticky materials typical of many industries. Some studies4 have shown a decrease in discharge rate with an increased moisture content of the material. However, no attempt was made to correlate the discharge rate with moisture. The method of calculating discharge rate presented in this paper was derived analytically from the basic knowledge of the flow of frictional, cohesive, granular solids, The equation includes the effect of material cohesion (stickiness), hopper configuration, opening size and bulk density of the material. THEORETICAL WORK The basic assumptions made in deriving the discharge rate equation are as follows: 1) The material is a frictional, cohesive, granular solid. 2) The flow is considered continuous and without significant density change. 3) The material at the hopper opening forms a continuously failing arch that is in dynamic equilibrium. 4) The strength of the material in the arch, which must be overcome for the arch to fail, is caused by the pressure in the flowing mass near the hopper opening. 5) This pressure at the hopper opening can be calculated5. If we consider the dynamic equilibrium of an arch of uniform thickness such as that shown in Fig. 1,

Jan 1, 1965

By R. C. Hall

In the present work, experiments determined the effect of the order-disorder reaction near the Fe,Al composition on the magnetic anisotropy and magnetostriction of single crystals: A material which is more difficult to magnetize in one direction than in another is anisotropic, that is, the ease with which ferromagnetic materials may be magnetized in different crystallographic directions determines the anisotropy. Two investigators have estimated the anisotropy of the aluminum iron alloys from poly-crystalline data;1,2 however, these estimates should not be considered to be reliable. Siege1 made two accurate measurements of the first anisotropy constant* from single crystals of 4.0 wt pct aluminum sotropy throughout the ferromagnetic aluminum iron system have been described. These results were obtained from single crystals which were slowly cooled and, hence, ordered near the Fe3Al composition.4 Magnetostriction is the change in length per unit length resulting from applying a magnetic field to a ferromagnetic material. For the purpose of this report, the saturation magnetostriction was measured. This is the maximum change in length per unit length resulting from an applied magnetic field large enough to saturate the material in a given direction. This magnetostriction has been determined for single crystals of the ferromagnetic aluminum-iron system.' The crystals near Fe3Al were also ordered. PREPARATION AND TREATMENT OF SINGLE CRYSTALS Single crystal bars were grown from the melt.' The raw materials for these crystals were iron and aluminum of 99.9 and 99.99 pct purity, respectively. From the bars, crystals in the shape of circular

Jan 1, 1959

By A. S. Richardson

VENTILATION of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air- conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust- prevention measures that have been developed comparatively recently. FACILITATING FLOW OF AIR As a basic requirement for the safety of the men, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft is available as a base for fire-fighting operations. Control of the direction of air flow is

Jan 1, 1938

By J. H. Nead

OBJECT THE experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. CONCLUSIONS No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability.

Jan 12, 1915

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced' by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

By O. C. Ralston

The use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know. It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it [nay be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite. Activation of sphalerite takes place in alkaline, neutral or weakly acid solutions and whereas the present day flotation of sphalerite is usually in ah alkaline solution, the early use of copper sulfate was in a sulfate solution.

Jan 1, 1930

By Oliver S. North

Reserves of perlite rock in the western section of the United States are immense. A geological report prepared for the Union Pacific RR showed proved tonnage of over 400 million tons in southern Nevada alone. Yet the perlite industry is not large, and most of the mines are relatively small. There are indications that perlite processing, thus far largely in the hands of relatively small com¬panies, is becoming concentrated in a few large companies. For economic reasons the bulk of perlite sold in crude form has come from three or four pro¬ducers, although many individual operators have sold small quantities to limited lists of purchasers. Perlite is one of ultra-lightweight aggregates. Owing to its outstanding qualities as an aggregate, variety of uses, and ultimate economy of use, it has enjoyed considerable popularity in this country in recent years. Marked foreign interest also has been evinced in this material.

Jan 2, 1955

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart' reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,' and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

By M. C. Miller, M. R. Tek, D. L. Katz

Previous studies have shown the influence of geometric variations on the drawdown and buildup behavior of a well completed in a homogeneous, porous medium containing a single-phase fluid. Other papers have shown the influence of leakage across caprocks on drawdown tests on water wells and aquifers. This paper presents two additional cases: the influence of an adjacent, expansible source of fluid, and the effect of caprock leakage on the measured in situ permeability and compressibility. Methods are developed for evaluating the influence of these two deviations from a uniform aquifer upon the in situ permeability and compre.ssibility indicated by pump tests. INTRODUCTION In relatively uniform porous media, saturated with a single-phase fluid, the effective reservoir permeability and compressibility of the water porous bed system may be obtained from drawdown and build-up data on wells, such as the initial wells drilled in aquifer storage reservoirs (Homers and Katz et al.7). In considering the drawdown and build-up behavior of wells adjacent to storage reservoirs, or of wells in an aquifer adjacent to an unknown gas field, questions arise as to the quantitative effect of the presence of compressible fluid on the measured permeability and compressibility of the formation. The solution to this problem is presented, using a constant pressure line source at some distance from two wells, one of which is pumped and the other used as the pressure observation well. The solution is presented in terms of the geometry of the wells and their relationship to the constant pressure line. It is known that caprock leakage can interfere with the determination of an aquifer in situ permeability and compressibility (Mantush4, Hantush and Jacob3 and Witherspoon and Muellerll). This paper presents an added case of the effect of leakage through a caprock of known thickness and permeability on well tests starting with a reservoir of constant pressure above the caprock and contributing to the aquifer as a result of the pump test. Again, both a pumping well and an observation well are postulated. These two cases are presented together since both a compressible fluid nearby and. caprock leakage show similar deviations from expected in situ permeability and compressibility results, and the solutions are similar in form. EFFECT OF A NEIGHBORING CONSTANT PRESSURE SOURCE ON IN SITU MEASUREMENTS Bixel, Larkin and van Poollenl presented a paper showing the influence of a discontinuity of the properties of a fluid formation system on drawdown and build-up performance. Their case is related to the present study but may be distinguished from it in that their numerical work and resulting graphs relate only to the performance of the pumping well itself. Incorrect values for in situ reservoir properties may be obtained from pump test data if the skin effect of the well and after-flow are not considered. Analysis of this problem by the authors indicated that the more reliable method of evaluating the influence of an adjacent gas field or expansible source was to use one well for pumping and another well at some distance from it for observing the aquifer pressure performance. An expansible source of hydrocarbon near a pumping well may be approximated by a line of constant pressure for a pump test. Fig. 1 illustrates a pumping well and an observation well near a line of constant pressure. Pressure behavior of an observation well during a drawdown pump test near a line of constant pressure is given by the diffusivity equation:

Jan 1, 1967

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

By T. M. Girdler

INDUSTRIAL progress and development in this country from the earliest daps to the present has proceeded at an ever-quickening pace. Yet during recent decades the nature of our industrial progress and development has undergone a change of great significance. The earlier days were a period of tremendous expansion. Population was increasing by leaps and bounds. Vast areas of new land were being .2 opened to settlement. And almost boundless new sources of timber, coal, oil, ores, and power were being opened to ever-expanding markets. Today, however, that picture has al- most completely changed. Today, with population increase tapered way off and the opportunity for free expansion into western frontiers gone, the great industrial development of our country continues on a vastly different front. Industrial progress and development today rest on a foundation of technology. The key- stone is research. Our frontiers to- day are frontiers of sciencec

Jan 1, 1939

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944