Search Documents

By Raynor Linzey, Karl M. Busen

The formation of thin films of silicon oxide by anodic oxidation of silicon and the subsequent removal of these films by an etch is a process often used for the evaluation of concentration distributions Profiles) in silicon layers by the differential sheet conductance method. The accuracy of the resulting profile is very strongly influenced by the uniformity of the thickness of the reacted silicon. Normally, it would be expected that for a constant number of coulombs passed the thickness would be the same from oxidation to oxidation. Investigations show that in certain electrolytes, for a given number of coulombs passed through an n-type silicon sample, the thickness of the reacted silicon increased with increasing resistivity. Even for the same resistivity the thickness varied sometimes by a factor of 1.5. When an electrolyte was used which consisted of 10 pct water by volume in ethylene glycol with 4.0 g KNO per 1000 ml of solution, anodiza-tion at 5 ma per sq cm led to satisfying results. Short-time anodizations gave oxide layers of a higher apparent density than those experienced from thermally gown silicon oxides. THE functioning and the electrical characteristics of semiconductor devices are based upon the incorporation of "impurities" into a single-crystalline body of suitable material and on the concentration distribution (profile) of this impurity. The incorporation can be achieved by well-known processes as, for example, by diffusion, epitaxial growth, alloying, or ion implantation. Often the profile resulting from these processes is not known. A powerful tool to learn about a concentration distribution is given by the method of differential sheet conductance which employs successive four-probe measurements on a layer subjected to stepwise removal of thin sublayers. Differential sheet conductance vs position (or penetration depth) of a sublayer is plotted and a smooth curve is drawn through the data. From this curve the profile is then calculated. When the semiconductor material is silicon, the sublayers are removed suitably by anodic oxidation of the silicon and subsequent dissolving of the formed silicon oxide by an etch. The accuracy of the resulting profile is very strongly influenced by the uniformity of the sublayer thickness. Normally, it would be expected that, for a constant number of coulombs passed, the thickness would be constant from oxidation to oxidation. Investigations showed that for sublayers several hundred angstroms thick the reproducibility can be rather poor. Therefore, efforts were made to obtain a reliable technique for uniform removal. The present paper describes such a technique and certain phenomena which were encountered during the investigations. APPARATUS AND TECHNIQUE The first report on the investigation of concentration distributions, where for differential sheet conductance measurements thin silicon sublayers were removed from a diffused layer by anodic oxidation, was given by Tannenbaum. The author reports the removal of sublayers which for the most part were 400 thick. More advanced device designs now require much narrower layers. When it was tried in these laboratories to determine profiles within such layers, difficulties were encountered with respect to sublayers which by necessity had to be thinner than the ones reported by Tannenbaum. The apparatus used for the investigations is sketched in Fig. 1. Two cylindrical containers connected by a wide tube are filled with an electrolyte. The left container receives the cathode whereas the right container is closed at the bottom end by a sample support consisting of a Teflon base and a copper pedestal. The silicon sample (1 by 1 cm) is mounted to the pedestal embedded flush in the Teflon base using silver paint (Degussa) for electrical contact. Pyseal is applied to the edges of the sample to protect the copper pedestal from the electrolyte. The base is mounted to the container using a water-tight silicon rubber gasket. Fig. 2 gives a view of the sample support. The copper pedestal is connected to the positive side of a power supply operating at a constant current output (Kepco Model ABC 425M). The electrolyte which has been reported by Duffek et al. consisted of either 2 or 10 pct water by volume in ethylene glycol and 4.0 g KNO3 in 1000-ml solution. The electrolyte is best prepared

Jan 1, 1967

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.'

Jan 1, 1964

By Morris Muskat

ALTHOUGH the problem of well spacing is one of the most important involved in the production of oil, it must be considered at the present time as still subject to further development. The published literature on this question is so voluminous that we cannot enter here into a review of it, except to refer to the recent papers by L. L. Foley1 and E. A. Stephen-son,2 where other references are cited. However, a decisive and conclu-sive answer to the problem of well spacing in any general form does not seem to have been developed. And while we shall be unable to present the desired solution in the present paper, it is nevertheless felt that the material to be given here not only provides the physical ground work for the ultimate solution, but shows qualitatively the essential factors that enter the well-spacing problem. Field studies of the well-spacing problem, in which the ultimate recoveries from different fields with different well spacings have been compared, have generally suffered from the lack of knowledge as to the similarity of the inherent characteristics of the producing reservoirs being compared, such as the sand volumes, the sand porosities, the sand permeabilities, the original reservoir pressures, the presence or absence of gas caps, the presence or absence of effective water drives, and the economic limits of production rates at which the various fields were considered to have yielded their ultimate recoveries. Certainly no one who is evaluating originally the economic significance of any oil reservoir would deliberately ignore these phases of the problem. And it is equally certain that no one would reasonably expect the ultimate recoveries from two reservoirs, even with the same well spacing, to be identical regardless of these other factors. More reliable results might be expected from comparisons of the recoveries obtained from different leases with different well spacings, but producing from the same reservoir sand. Unfortunately, however, even conclusions for such studies may be subject to serious errors. The reason simply is that however much one may insist that an operator is entitled only to the oil immediately underneath his surface acreage he will nevertheless drain the surrounding properties as long as his reservoir

Jan 1, 1939

By Jin Zigang

In China there are more than 30 coal fields menaced by karst-confined water. In the north and east of China there are many collieries which mine coal seams of the Carboniferous and Permian Systems, which are above the Ordovician limestone (general thickness is 500-600 meters). Ordovician limestone is full of karst fissures, contains a lot of water under high pressure (15-65 kg/cm2) near the commercial coal seams (20-80 meters), the water easily infiltrates the thin lime- stone at the point of the structure crevice, so water-irruptions from the floor are the main source of water-related disasters in these coal fields. According to the statistics there were more than 300 accidents of all kinds of water-irruptions from the floor in these fields since the beginning of their development. It is of great significance in developing coal production in the eastern part of China to solve the problem of safe mining of the seams menaced by the karst-confined water of the Ordovician limestone. The research on this subject consists of three parts: (1) investigating the geological structure and hydrogeological conditions of each mine of the mining area; (2) researching the mechanism of water-irruptions from the floor and proposing reliable methods to predict and monitor; (3) improving the mining system and proposing a mining plan with safety precautions against water-caused accidents. The chief task is to research the mechanisms involved and to discover the causes and conditions of the phenomenon. The authors have obtained some findings on this subject in the last five years, making use of the comprehensive observation and research system, which will be discussed under three headings.

Jan 1, 1984

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By E. G. Woods, A. G. Comer

A mathematical model is presented and solved for determinution of the saturation distribution and pressure in a radial gas-storage reservoir. The model consists basically of two parts: (I) the growing gas-bubble core, and (2) the surrounding aquifer. Since the total pressure at the injection well is a function of the two-phase flow in the gas bubble and the unsteady single-phase flow in the aquifer, the resistance to flow in both zones was taken into consideration. The assumptions involved for both the radial equivalent of the Buckley-Leverett two-phase-flow equation and the injection-pressure equation are as follows: (I) the geometry is radial, (2) the gas bubble is free to expand or contract, (3) compression or expansion of the gas within the bubble may occur at the beginning of a time step, (4) the fluids are immiscible, (5) water is incompressible within the gas-storage region whereas it is compressible outside of this region, (6) a stable gas-water interface exists and (7) gas injection occurs at a constant rate or a series of constant rates. The mathematical model was solved numerically using an IBM 650 computer. A comparison is presented between the predicted results of the model, the results assuming steady-state flow and the actual initial injection-pressure history of an operating reservoir. Using the initial field pressure for a basis, the average deviation between the predicted pressure and the actual field pressure was less than 4.3 per cent. INTRODUCTION Underground storage of natural gas in abandoned oil fields, in abandoned coal mines, in caverns and in aquifers has had varying degrees of success. The lack of these first three facilities in the vicinity of most major gas marketing areas is leading more and more to storage in virgin aquifers. For the most part, this storage in aquifers has led to the study upon which this paper is based. Several excellent papers have been published discussing the problems involved in the underground storage of natural gas; however, to these writers' knowledge, none of them considered the two-phase flow of fluids in the gas bubble and the fact that the gas bubble will grow or shrink in size depending upon the injection and withdrawal history of the reservoir. Not only will both of these factors influence the required injection pressure, but also they will have a definite bearing upon the amount of water production occurring upon withdrawal from the storage area. To solve this problem on an IBM 650 computer, several simplifying assumptions were made. Only the drainage portion of the relative-permeability curve was considered, thereby neglecting any hysteresis effects introduced during an imbibition cycle. The quantity of gas withdrawn during the period of the field study was only a small percentage of the total gas in place; therefore, this assumption is justified. For the problem studied in this case, the combined effects of capillarity and gravity were assumed to be negligible. This assumption becomes less valid as the formation thickness or the average pore diameter increases markedly. The justification of these assumptions should be studied in each case. THEORY This mathematical model for the prediction of saturation distribution and pressure for a radial gas-storage aquifer is based upon the equations for radial two-phase fluid flow'.' and for radial, unsteady-state, single-phase fluid flow.' The two-phase flow is considered to take place in a "core" whose radius is equal to the maximum radius that the gas zone will attain, as indicated in Fig. 1. The injection-withdrawal history is approximated by a series of constant flow rates. Within the "core", gas is assumed to behave as a semi-compressible fluid; that is, the gas is assumed to have a constant density based on the average gas-zone pressure for the flow period. Between each constant-rate time increment, the gas density is allowed to change. This involves an iterative solution of the pressure equation. The liquid phase in this zone is considered to be incompressible, whereas it behaves as a compressible liquid outside of this region. The equations of incompressible flow in the "core" may be written for the gas phase

By M. T. Simnad, G. Derge, Ling Yang

STUDY of diffusion in molten substances is important in at least two respects. Diffusion data, combined with thermodynamic and kinetic information, throw light on the structure of the liquid state. Moreover, a knowledge of diffusion coefficients and their temperature dependence is useful in ascertaining the controlling step in many metallurgical reactions. Although diffusion measurements have been made on a number of molten salts, slags, metals, and alloys,'-'" the results available are still limited and widely scattered, especially for the high temperature melts. It is the purpose of this investigation to establish reliable procedures for the measurement of self-diffusion coefficients in high temperature melts and to use these procedures to determine the self-diffusion coefficients of iron in molten Fe-C alloys of different carbon contents. Experimental Measurement of self-diffusion coefficients in high temperature melts is usually carried out by using one of two methods. In the first, diffusion takes place between two cylindrical samples of the same material, one of which is made radioactive. The diffusion coefficient is calculated from the radioactivity penetration curve in the solidified sample after the diffusion. In the second method, samples contained in capillaries of an inert substance are immersed in an infinite reservoir of the same material. Either the material in the capillary or that in the reservoir is made radioactive and the diffusion coefficient is calculated from the change of the radioactivity of the sample in the capillary after the diffusion. The second method is simpler because a radioactivity penetration curve is not needed for the calculation of the diffusion coefficient; however,.it is valid only when no convection has occurred in the capillary during the diffusion. A radioactivity penetration curve is therefore always useful in indicating that the required conditions for the diffusion are ful- filled. Towers and Chipman" recently studied the self-diffusion of calcium and silicon in CaO-Al,O,-SiO, melts by using the capillary method. Instead of measuring the change of the radioactivity of the sample in the capillary, they autoradiographed the sample after the diffusion and calculated the diffusion coefficient from the intensity distribution of the autoradiograph. Their method is useful when the radioactive isotopes are weak ß-emitters, but is very difficult, if not impossible, to apply to cases involving strong ß or y-emitters. For such cases, sectioning of the sample according to the method of Morgan and Kitchener' may be used for the construction of the radioactivity penetration curve. The self-diffusion of iron in molten Fe-C alloys has been studied in this manner and the experimental procedures are described as follows: The diffusion apparatus is shown schematically in Fig. 1. The bath consisted of about 200 g of an Fe-C

Jan 1, 1957

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By Carl F. Floe, Michael B. Bever

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Raymond Mancha

The use of blower fans and tubina- for auxiliary face ventilation is a somewhat controversial subject. Most authorities agree upon the advantages of this system over the maintenance of line brattice for dead-end ventilation. They also recognize the system's disadvantages. However, there is considerable disagreement as to the proper relation of the advantages to the disadvantages. It is the purpose of this report to present the opinions of four authorities of diversified occupation and permit the reader to form his own opinions on the subject. ORsErvers Carel Robinson is a mining engineer consultant of wide repute, who has a background of operating experience. Thomas G. Fear is a mine operator whose present position is that of chief engineer for the Hanna Coal Co. at St. Clairsville, Ohio. E. H. Denny is chief of the Coal Mine Inspection Division of the U. S. Bureau of Mines, and is a very able engineer whose past experience well qualifies him to appraise this problem. Cloyd M. Smith, editor of the periodical Mechanization, is a ventilation consultant. For a number of years he was a member of the Mining Department of the University of Illinois and has studied mine ventilation for many years. It is Mr. Robinson,s opinion that closely spaced breakthroughs, although conducive to low gas accumulation past the last open crosscut during the driving of entries, are difficult to maintain and are constant Sources of fugitive air. Jute or canvas brattice is suitable for entry driving with

Jan 1, 1944

By Laszlo Valentyik

To separate minerals on a small scale according to their specific gravity, heavy liquids are used, but because of high costs and health hazards they cannot be used in large scale plants. In order to substitute heavy liquids, finely ground solids like magnetite and ferrosilicon mixed with water and clay for the required specific gravity are employed. The clay present in the medium acts as a stabilizing agent since the coarse heavy media solids would sink very fast to the bottom of the container if they were mixed only in water. The optimum amount of clay varies for different processes, but it is generally between 3-6% by weight concentration of solids. As the pseudo-plastic nature of polymer solutions has excellent suspending properties, investigations were conducted at the Institute of Mineral Research to ascertain whether polymers could be used commercially as suspending agents for finely ground heavy media.

Jan 1, 1973

By James F. Kemp

Discussion of the paper of JAMES F. KEMP, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1801 to 1836. WALLACE E. PRATT, Manila, P. I.-I am glad that Professor hemp has referred to the Philippine ores in his paper, inasmuch as I have had the privilege of examining, in a preliminary way, the ores there. I must say, from the resume given us, that the Daiquiri ores seem to be similar in origin and character to the magnetite-hematite ores in Bulacan Province, Philippines. Professor Kemp has also referred to C. M. Weld's description of the magnetite-hematite ores at Hongkong and to the similarity of these ores to the ores at Daiquiri and to those in Bulacan. There is a minor feature of apparent difference in origin in the Hongkong and Bulacan ores. Mr. Weld believes the iron ores at Hongkong to have resulted from the intrusion of the Hongkong granite, a distinctive rock of wide distribution in the Orient, into sedimentaries which are probably of much greater age than those which have been replaced in part by the ores in Bulacan. Associated with some of the ores in Bulacan and elsewhere in the Philippines there is a granite which may be the equivalent of the Hongkong granite; but the Bulacan ores are not related in origin to the intrusion of this granite, which is clearly older than the ores, but to the later intrusion of dikes and small bodies of basic rocks into the granite and into associated tuffs, breccias, and sedimentaries, including limestone. I gather that the intrusives to which the mineralization is related at Daiquiri are also small in volume and later than larger bodies of associated igneous rocks, from which it would appear that the Bulacan ores are even more closely related to the Daiquiri type than are the Hongkong ores. The deposits in Bulacan are inaccessible and are not large, the largest one containing about 1,000,000 tons, according to an estimate based solely on its outcrop dimensions. Ores of similar character, however, occur in Camarines Province in apparently larger quantity and in a situation on the coast adjacent to deep water.

Jan 12, 1915

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By F. M. Stewart

A paper by Hurst and van Ever-dingen in 1949 led to the practical solution of many nonsteady-state flow problems.' Subsequently, applications of this material have been discussed by several authors. The purpose of this note is to outline a simplified direct procedure for water-influx pressure predictions for pressures above the bubble point. The prcposed procedure is unique in that after the "time-conversion factor" and the "influx constant" are obtained, predictions are made without trial and error. The elimination of trial and error is made possible by expressing certain PVT characteristics as explicit functions of pressure. The procedure is applicable to fields producing at pressures above the bubble point and under radial water drive from an infinite aquifer. In the usual applications it is required to predict (1) withdrawals given future pressure history or (2) reservoir pressure, given future withdrawals or production. The theory, assumptions and conditions under which the nonsteady-state solutions hold are covered in the references and are not repeated. The simplified direct procedure outlined here has been developed from published solutions for the so-called "pressure case". A similar direct procedure for the same special conditions has been developed for the "rate case"; however, in this instance the procedure is lengthy and offers no advantage over the trial-and-error solution. Consequently, this paper covers only the procedure based on the pressure case. DISCUSSION Under the pressure case prediction of withdrawals from a water-drive field, given the future pressure history, involves the use of a nonsteady-state water-influx term together with the material balance equation. The solution of a particular problem requires the following steps: (1) division of past pressure and production data into equal time intervals; (2) computation of cumulative water influx vs pressure drop for each time interval of past history using the material balance equation; (3) determination of the best values for the "time-conversion factor" and the "influx constant" by equating the nonsteady-state influx term with the influx computed in Step 2 (this requires a trial-and-error procedure); (4) prediction of influx for a given pressure drop using the influx term and the computed factors from Step 3; and (5) calculation of fluids produced using the predicted influx in the material balance equation. A forecast of the water-oil ratio or water production rate is required to complete the calculation. It is assumed that a reliable estimate of original oil in place is available, as well as the production and pressure history, and data on reservoir fluid characteristics. If the original oil in place is unknown, it may be computed simultaneously with the tinie-conversion influx factors2,3. However, the oil in place so computed may be considerably in error3; consequently, it is usually preferable to use oil in place estimated from pore-volume data unless there is considerable doubt as to its accuracy. The Material Balance Equation Above the Bubble Point Above the bubble point the simpli-

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By BION J. ARNOLD

WE can, I think, rightfully claim, irrespective of our faults, that engineers must, in order to last as engineers, possess the qualifications of integrity, stead- fastness of purpose, ability to think straight, and to apply these qualities consistently and continually in their everyday work. All engineers know this, most of them conform, and in order to drive it home I might, if 'clothed with proper authority, preach to you at length, but I shall not take the chance. So I only want to make a suggestion or two to the young engineers. Have an ideal and work toward it. You will have your disappointments and your temptations but keep your record clean, and if anyone says you are foolish or ugly, or homely, or that you need a guardian, take the criticism with a smile, for he may be able to prove his contention; but if he attacks your integrity, strike at once and fight hard, for he has assailed not only your character but your principal asset as an engineer.

Jan 1, 1929

By Mohamed Mortada

A practical analytical method is developed in this paper which provides the practicing reservoir engineer with a handy method for analyzing oilfield interference problems. The procedure employed entails the principle of superposition of individual eflects. A set of charts has been developed and can be used to evaluate the individual effects. The charts represent non-steady state pressure distribution in an extensive aquifer due to a constant rate of production from an oilfield which can be approximated by circular geometry; they are constructed from solutions to the diffusivity equation considering a circular sink as distinguished from a point sink. The solutions are obtained partially from mathenlatical considerations and partially from analog and digital computations. By virtue of the method of images, the charts can be used also to treat the case of production near a fault. In addition, provisions are made for treating oil fields, which are produced by partial water-drive. Treating an actual field case is deferred to a subyequent writing; however, illustrative example is presented to demonstrate the method of application. The pressure distribution in linear and limited radial aquifers is currently under study. INTRODUCTION With the increasing difficulty of discovering new oil reserves, attention is necessarily focused on the efficient development and production of existing reservoirs. Efficient production depends on the availability of reliable means for predicting the pressure-production behavior of oil fields. The prediction is usually performed by analytical methods or computers. Analytical methods are often limited to systems which can be approximated by simple geometry. However, analytical methods have the distinct advantage of being readily performed without special equipment. Analog and digital computers lend themselves to a variety of problems, but are not always locally available and consequently their use is limited. One particular situation in which analytical techniques are needed involves studies of multiple, water-drive oil fields sharing a common aquifer. Such oil fields are in hydrodynamic communication. Therefore, production from any of the oil fields is accompanied by a pressure decline which is transmitted through the aquifer to the other oil fields and manifested as pressure interference. The rate of propagation of the pressure decline is such that the pressure may be significantly reduced many miles away from a producing pool. An example of pressure interference is found in the Woodbine formation in East Texas. There. a dozen or more pools, including several of major size, draw on the Woodbine formation for water drive. The pressure in the water-bearing portion of the formation has been significantly reduced over an area of several thousand square miles. This reduction of pressure has been such that when the Hawkins pool was discovered in 1940, the pressure in it had already been reduced 280 psi below the initial value in the aquifer. This resulted from prior production from other Woodbine sand pools, including, in particular, the East Texas field some 20 miles to the east of Hawkins.' The above example indicates that the interference effect can be significant and should be taken into con-

Jan 1, 1956

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By G. W. Nabor, A. S. Odeh

The effect of production history of a well on the results of two-rate flow tests, and conventional build-up analyses was investigated. The effect was examined by means of digital computers and an R-C network model, respectively, for wells with infinite and finite radii of drainage. For systems which behave as infinite, it was found that production history and the duration of production at constant rate prior to the initiation of the test have important effects on the results. During build-up time equal to about one-fourth of the stabilized time, correct permeability-thickness product calculations can be made. For wells with finite radii of drainage, the time was determined during which the straight line can be satisfactorily used for permeability-thickness product calculations in case of drawdowns and build-ups. On build-ups, the dimensionless time (based on the external radius) during which the straight line gives reliable results was detertriined to be about 1/12. This is one-fourth as long as that of the drawdown. The investigation was done theoretically, and subsequently was verified by R-C network model runs. General interpretive rules were formulated which, if not followed, could lead to serious errors. Moreover, a recommended testing procedure is reported. INTRODUCTION The method used by most reservoir engineers for estimating formation characteristics in a producing well is the analysis of pressure build-up data. The method originally devised by Horner' makes use of the point source solution to the diffusion equation. This solution is approximated by a logarithmic function and the superposition principle is employed to arrive at the well known pressure build-up equation:where q, the flow rate, is in reservoir B/D; ft is in cp; kh is in md-ft; At is the shut-in time; and t is the producing time. At and t are in any consistent time units. Ey. 1 is applicable to a well of unlimited drainage radius which produces at a constant rate q from zero to time t and is then shut in. Such a constant production rate seldom obtains in practice. Therefore. a correction term must be applied to Eq. I to account for the varying rate. Two theoretically accurate methods are available for treating the variable rate case. The first, originally derived by Horner,' is based on the application of the superposition theorem. It requires knowlege of production history of the well as a function of time and results in lengthy and laborious calculations. The second t*q* niethod is suited for short production tests and requires that the shut-in time be at least one and one-half times the production time. A third method which is not based on any theoretical justification and which was suggested by Horner as a "good working approximation" is the one used by the majority of reservoir analysts. especially when the well has been producing for a long time and the t*q* method is not practicable. The key to this method is in choosing or determining the t that appears in Eq. 1. Horner suggested using a corrected time t, in place of t. t, is calculated by dividing the total cumulative production by the last established rate. Therefore, a normal procedure of pressure build-up testing is to stabilize the well at a constant rate for at least 24 hours before shut in and to use the stabilized rate to calculate t,. The analysis is then made by plotting either or P. and examining the resulting plot for the expected straight line to calculate kh and the original reservoir pressure. Recently, Russell" proposed a method for determining formation characteristics from two-rate flow tests. His method reduces to pressure build-up if the second flow rate is zero. Russell uses the Horner simplified procedure for calculating a corrected t,. His method also requires the stabilization of the well at a constant rate q which is used to calculate t,. Theoretically, the above procedure is valid for a well with an unlimited radius of drainage or with a limited radius as long as the boundary effect has not been felt by the well. Several authors'' derived formulas which allow the estimation of time during which limited reservoirs behave as infinite ones and, thus, can be treated by unsteady-state mechanics. One equation derived by Swift and Kiel' terminates the application of unsteady-state theory when the drainage radius reaches one-half the reservoir radius. Thereafter, steady-state behavior obtains. Another equation derived by Jones'" initiates steady-state

Jan 1, 1967