Search Documents

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

By E. L. Brack

ASARCO's copper smelter at Hayden, Arizona has been upgraded to meet the increasing Environmental Protection Agency (EPA) and Occupational Safety and Health Administration (OSHA) environmental standards. Fortunately, means were found to accomplish these standards and provide for more efficient operations. With the adaptation of oxygen flash smelting and other related operations at Hayden, ASARCO has turned to the use of minicomputers and microprocessors for inter-plant communications and local area process control. The applications of distributive and computer controls to the plant operations at the Hayden smelter are discussed in this paper.

Jan 1, 1984

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By John Chipman, Theodore B. Winkler

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Theodore B. Winkler, John Chipman

In order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and. abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chip-man,3 dealt with the simplest possible slag system that would resemble those found in the basic ope), hearth—the slag system consisting of CaO-MgO2-SiOz-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemis- try of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, SiO2, FeO, Fe2O3, P2O6, MnO, Al2O3 and CaF2, but not all of the slag samples contained all of these components at one time. Review of Literature Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Krings,4 von Samson-Himmelstjerna,6 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution . Ratios

Jan 1, 1947

By Daniel M. MacNeil, Carle R. Hayward, Raymond L. Presbrey

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By Daniel M. MacNeil, Raymond L. Presbrey, Carle R. Hayward

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By M. R. Tek, F. F. Craig, J. O. Wilkes, C. S. Goddin

The waterflood performance of a water-wet, stratified system with crossflow is computed by a finite difference procedure. The effects of five dimensionless parameters on tile oil displacement efficiency, water saturation con-tour.7 and crossflow rates are evaluated in the absence of gravity forces. Crossflow due to viscous and capillary forces is shown to exert a significant effect on oil recovery in a field-scale model of a two-layered. water-wet sandstone reservoir. The crossflow is at a maximum in the vicinity of the front advancing in the more permeable layer. Under favorable mobility ratio conditions, the comparted oil recovery with crossflow always is interrnerliate between that predicted for a uniform reservoir and that for a layered reservoir with no crossflow. INTRODUCTION The important erects of reservoir heterogeneity on waterflood performance are commanding increased attention in the technical literature. Much of this attention is centered on two categories of layered reservoirs: those in which layers are non-communicating and those in which crossflow of fluids occurs between the layers. In the first category, the reservoir is assumed to consist of discrete layers, each uniform within itself and differing from the others only in such properties as thickness, porosity and absolute permeability. The performance within each layer is calculated by one-dimensional flow theory, and the performance of the total reservoir is obtained by summing individual layer performances. Capillary and gravity effects usually are not considered. Representative publications dealing with thi5 type of reservoir are those of Stiles,' Dykstra and Parsons,' Hiatt,3 Warren and Cosgrove' and Higgins and Leighton." Prediction of performance for reservoirs in the second category is considerably more difficult since viscous, capillary and gravitational forces all play important roles in causing crossflow between layers. A number of authors have investigated the simpler problem of two-dimensional displacement flow in a stratified system with a mobility ratio of unity and negligible capillary and gravity effects.'; Others have considered two-dimensional, non-steady-state flow of a single, slightly compressible fluid in a stratified reservoir. A limited number of laboratory oil displacement tests in layered models with crossflow have been reported. Miscible floods (with resultant zero capillary forces) in layered five-spot models were conducted by Dyes and Braun," who studied the effect of mobility ratio with zero gravity forces, and by Craig et al. 12 who studied the effect of gravity forces at constant mobility ratio. Waterfloods in layered five-spot models (with cross-tlow due to capillary, viscous and gravity forces) were conducted by Gaucher and Lindley,"' who showed the effect of gravity forces in causing underrunning of the injected water and by Carpenter, Bail and Bobek, 14 who demonstrated the reliability of Rapoport's" dimension-less parameters for scaling layered systems. Waterfloods in rectangular layered models were conducted by Richardson and Perkins."' who investigated the effect of velocity at constant mobility ratio and with zero gravity forces, and by Hutchinson," who studied the effects of varying mobility, layer permeability and layer thickness ratios. The differential equations which rigorously describe waterflooding in a heterogenous porous medium are non-linear and do not facilitate analytical solution. By using finite difference approximations it is possible to obtain a solution to any desired degree of accuracy. Such a solution, using an alternating direction implicit procedure (ADJP), is described by Douglas, Peaceman and Rachford.18 In the present study, a computer program using ADJP explores systematically the effects of important parameters on waterflood performance of a two-dimensional, two-layered, field-scale model of a water-wet sandstone system. Particular attention is given to evaluation of the water saturation contours and crossflow rates at the interface between layers to gain improved understanding of the crossflow mechanism. PROCEDURE BASIC: FLOW EQUATIONS The basic flow equations for two-dimensional, two-phase, immiscible, incon~pressible flow in a porous medium are:

Jan 1, 1967

By V. A. Phillips, M. Safdar Ali

The tensile properties of Cu-0.20 pct Al, Cu-0.45 pct Mg, Cu-0.27 pct Cr, and Cu-0.22 pct Be solid-solution alloys were studied at -196°, 18°, 2509 and 500°C on wires internally oxidized at 900°and 1000°C. Internal oxidation produced marked increases in yield strength relative to pure copper, particularly at low temperature. The yield strength decreased with increase in temperature to a much greater extent than predicted by current theories of dispersion hardening. The strengthening effect of internal oxidation persisted throughout the entire stress-strain curve, but since a marked loss of ductility occurred at all test temperatures, only modest increases in tensile strength were realized. INTERNAL oxidation involves the preferential oxidation of a baser solute in a relatively noble solvent by diffusion of oxygen into the solid. Since the process is diffusion controlled, it is expedient to carry it out at a high temperature often approaching the melting point. The amount of solute is limited and the oxidation conditions adjusted so that oxygen diffuses inwards to meet the solute causing reaction to progress inwards and form subscale instead of only sur face scale. The reaction can be made to occur throughout the thickness of thin material producing a fine dispersion of oxide inside the metal. C. S. Smith1"3 appears to have been the first to recognize the true nature of the process of internal oxidation. Although extensive kinetic and metal-lographic studies followed by Rhines and coworkers,4-5 Chaston7 andMeijering and Druyvesteyn8 working independently were the first to report hardening effects due to internal oxidation. These results prompted detailed studies of the effects of internal oxidation on the hardness, tensile, creep, and fatigue properties of a number of alloys by G. C. Smith and coworkers9-12 in England, on hardness by Gottardi13 in Italy, and on hardness and tensile properties by wood14 in the U.S.A. Publications dealing with other aspects of internal oxidation will not be reviewed here. Internal oxidation of solutes having a high affinity for oxygen provides a means of obtaining very fine dispersions stable in a suitable atmosphere at temperatures well above those at which most age harden ing precipitates coalesce. The process therefore offers a method of producing thin sheet and wire of possibly outstanding creep resistance. The size limitation might be overcome by internally oxidizing porous powder compacts made from alloy powder before final sintering. PREPARATION OF ALLOYS The alloy ingots, which were approximately 5 1/2 in. long by 1 in. diam, were made up in a high-frequency furnace, using as raw materials OFHC copper, 99.99 + pct Al, high-purity magnesium, and master alloys of Cu-4.19 pct Be and Cu-10 pct Cr. The alloys containing aluminum and magnesium were melted ii closed high-purity graphite crucibles and solidified in the crucible which was lowered partly Out of the coil to give a hot-top effect. The alloys containing beryllium and chromium were made by melting in vacuo in alumina-lined sillimanite crucibles. The magnesium, chromium, and beryllium

Jan 1, 1960

By J. L. Taylor, P. Duwez

PARTIAL phase diagrams of titanium with iron, cobalt, and nickel have been established by previous investigators.1-3 These diagrams seem to be reliable, at least for concentrations of titanium ranging from 0 to about 50 at. pct. More recently, Long and his collaborators have presented a tentative titanium-nickel diagram covering the titanium-rich side.' These various studies indicate that in each system three intermediate phases exist and correspond to the compositions Tia, TiX, and TiX2 (or TiX3). The purpose of this paper is to review the available information on the crystal structure of these phases and to give the results of additional X-ray diffraction studies. Previous Work A summary of the work of Wallbaum and his collaborators"-' is presented in table I. The first intermediate phase on the titanium-rich side of the three systems, with iron, cobalt, and nickel, is of the Ti2X type and has a face-centered cubic structure. Although it is stated that the unit cell contains 96 atoms: no lattice parameters are given. The second phase is centered around the compositions TiX for the three systems. The crystal structure of this phase is mentioned in a short note" as being body-centered cubic (CsCl type), but no parameters are given. The analogy between the three systems, which is perfect as far as the two phases of the type Ti2X and TiX are concerned, disappears at the titanium-poor end of the diagrams. In the system titanium- iron, TiFe2 has an hexagonal (MgZn2 type) struc-ture with the parameters given in table I. The existence of TiFe3 has also been reported8 (table I) but was questioned by other investigators2 and is also refuted by the present study. In the system titanium-cobalt, a phase corre-sponding to the composition TiCo2 has been investi-gated by Wallbaum and Witte6 who claim that the structure is cubic (MgCu2 type) for alloys slightly deficient in cobalt and hexagonal (MgNi2 type) for alloys slightly deficient in titanium. The parameters of the two phases are given in table I. In the system titanium-nickel, the nickel-rich phase corresponds to the composition TiNi3 and has been described as hexagonal7 with the parameters given in table I. The present investigation was initiated for the purpose of filling in the gaps in the knowledge con-cerning the structure of the various phases sum-marized in table I. Since the titanium used by Wallbaum and his collaborators was only 95 pct pure,' it was found desirable to redetermine the lattice parameters of the alloys prepared with a

Jan 1, 1951

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982

By A. D. LeClaire

This paper claims to provide a description of diffusion processes in solids which is said to be a reformulation of Fick's Laws and therefore, presumably, is supposed to be as general as those laws. In fact, it appears to provide no more than an atomic model of a rather restricted type leading even to results in conflict with experiment. The restriction lies in the assumption, carried throughout the paper, that even in a chemical gradient the jump frequency i of an atom of species i is a function only of the composition on the plane from which it jumps, i.e., ?i = ?i(cl, c2 ...). This means that atom jumps in opposite directions from a site would occur with equal probability. There would then be no tendency for atoms to migrate preferentially in one direction along the gradient, so the model is incapable of accommodating the well established phenomenon of atom drift in a chemical gradient.10-" A more general model that does not suffer this difficulty was discussed in a paper13 I wrote in 1958, and the results therein already contain as a special case those given by Dr. DeHoff. The simplest sufficiently general assumption is to suppose that ?i is a function ?i(a1 a2,...; wl, w2, ..-) of the concentration aj and ? ?j at the site from which and to which, respectively, a jump is made. Any such function can always be expressed as a function of the sum and difference of its arguments. Thus d is the jump distance and g a geometrical constant. Obviously this is zero, i.e., no drift, if ??ri/??j = 0. X is written in this form, revealing two components of the total drift, because it can be shown that only the second component, depending on ??'i/???(?j -aj), actually contributes to the net diffusion flux Ji. This component can be shown,13 by a straightforward ther-modynamic transcription, to be responsible for the so called "thermodynamic factor" in the Darken approximation for a chemical diffusion coefficient is the activity coefficient of i. Because the jump rate ?i in DeHoff's approximation has no dependence on the concentration gradient it does not seem possible to derive the Darken equation from his Eq. [6] without the further rather arbitrary assumption that ?i = const ri. It is to be noted too that the author's derivation of Eq. [12] is only valid when ?i is in fact a function only of the cj at the plane from which the atom jumps—for only then is ci?i a unique function of position and therefore of A. Author's Reply R. T. DeHoff I am indebted to Dr. LeClaire for his penetrating discussion of my paper, "A Reformulation of Fick's First Law". I concede that it does appear initially that the relationship presented in my paper could be derived from the detail atomic model of random walk and atom drift presented in Dr. LeClaire's approach. However, there are some important differences in concept and viewpoint which deserve further amplification. Dr. LeClaire's description is penetrating, detailed, and fundamental. His approach describes an extremely complex phenomenon, the displacement of atoms in a multicomponent gradient, at a sophisticated level. For precisely these reasons, his analysis has not proved to be useful for experimental studies that have practical objectives. For example, in order to obtain the information required to complete the analysis of the jump frequency distribution in a ternary system, the following series of experiments would, I believe, be required: 1) chemical (gradient) experiments, covering the composition range;

Jan 1, 1970

By L. W. Eastwood

The structure of eutectics has been studied by a number of investigators, and the complexity of the structural relationship of the components has been agreed upon, especially that of the "eutectic colony," type III of Portevin's1 classification. This paper does not attempt to alter the present classifications of eutectics; rather, it discusses the relationship between the macrostructure and the microstructure of the copper-cuprous oxide eutectic, and describes in detail the mechanism of the formation and the structure of the eutectic. Further, throughout the entire discussion it attempts to point out certain misconceptions in regard to the interpretation of the observed structure of the copper-cuprous oxide eutectic, one of the so-called "eutectic colony" types, and to correlate as much as possible the work done by the writer with that done by other investigators. Of the three types of eutectics listed by Portevin,2 the eutectic colony type has presented the greatest difficulty in interpretation. Although the copper-cuprous oxide eutectic is typical of the eutectic colony type in appearance, it may not be truly representative because the copper forms about 96 per cent of the eutectic and the cuprous oxide about 4 per cent. The interpretation of the origin and structure of the "eutectic colony" given here is strictly limited, therefore, to the copper-cuprous oxide eutectic. Macrostructure Fig. 1 shows the macrostructure of the eutectic at 3 diameters, the melt having been chill-cast into an iron mold, the resulting specimen sawed into two parts and the section polished and etched with the usual mixture of hydrogen peroxide and ammonium hydroxide. This specimen contains 0.48 per cent oxygen and is only slightly hypereutectic. If such a melt is allowed to cool slowly, large macrograins will form without the columnar structure of Fig. 1 and the well-known phenomenon of liquation will occur, forming copper oxide dendrites at the top and copper

Jan 1, 1934

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living. The Foreign Assistance Act of 1948 was passed in April of that year, and established the Eco-

Jan 10, 1950

By Fred C. Bond, Jen-Tung Wang

Comminution energy is principally energy of deformation before break-age, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 8, 1950

By Henry Louis

The present paper comprises two parts, which have but little con nection with each other. The first is practically a continuation of the investigation on the specific gravity of gold liberated by means of acids from its alloys, on which subject I had the honor of presenting a brief note to the Institute in 1893 (Trans., xxii., 117); the second describes a series of experiments on the behavior of amorphous gold under the action of heat. By the kindness of Prof. W. C. Roberts-Austen, C.B., F.R.S., chemist to the Royal Mint, I have been permitted to conduct these experiments in the mint assay-office, all the splendid resources of which institution were freely placed at my disposal. I desire at the outset to express my obligations to Prof. Roberts-Austen and to all the staff of the mint assay-office for their kind assistance at all stages of my experiments. I.—The Specific Gravity of Gold in Alloys. In the note already referred to, I published my discovery that the gold left on dissolving out the silver from an alloy of gold and silver (which I shall here term " residual amorphous gold ") has a higher specific gravity than ordinary molten gold. I also pointed out that I had worked on very small quantities of material and with balances and weights on the accuracy of which I could not implicitly rely, and that in so far my numerical data were inconclusive, although I had but little doubt of the correctness of the broad fact. The experiments now recorded were made under the most advantageous circumstances and with various refinements. Particularly, I found that the ordinary form of specific-gravity bottle was responsible for several small sources of error; and I accordingly designed an improved form (Journal of the Society of Chemical Industry, April 30,1894, vol. xiii., p. 322), which I used for this work. The

Jan 1, 1895