Search Documents

By Samuel L. Hoyt

THE present report represents that part of the work that has been done by the War Minerals Investigation, Manganese Section, of the Bureau of Mines, on the use of manganese alloys in open-hearth practice. The magnitude of the work and the number of people participating in one way or another make it difficult to acknowledge adequately the services of all who have contributed to the success of the work. It would, be amiss, however, to pass to the body of the report without mentioning the hearty coöperation and willingness to assist of the various manufacturing interests. With such a sympathetic attitude toward this investigation, our work was assured of success. Inasmuch as the unhappy circumstances that rendered this investigation necessary have now passed, this report is made in 'the hope that the results may prove of some permanent value to the peace-tine operation of our open-hearth industry. Broadly speaking, the purpose of the manganese investigation was to consider the most suitable means of utilizing our domestic supply of manganese and thus relieve, to the maximum extent possible, our shipping of the burden of importing manganese ores. It was not held that any decided shortage of manganese 'was imminent but rather that every legitimate means should be utilized for making our ship tonnage available to European service. While we have considerable metallic manganese in this country, it occurs largely as a low-grade mixture with iron or silica or with both. The open-hearth investigations, therefore, were carried on to determine the extent to which domestic or low-grade alloys could properly be substituted for high-grade alloys without materially impairing the steel production as to either quality or quantity. Also, it was held that such an investigation would yield valuable results to the steel industry as well as contribute, in no small way, toward

Jan 2, 1919

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the -pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint .of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth .history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

S. F. EMMONS, Washington, D. C.: Papers of Collins, Vogt, DeLaunay, etc.-Mr. Collins tells us about facts in the veins of Cornwall that suggest secondary sulphide-enrichment is highly interesting; and I am free to confess that I have not studied the literature of that region as fully as I should have done. Nevertheless, even if it had been as familiar to me as it is to Mr. Collins, I should probably have hesitated to draw theoretical conclusions without having seen the mines myself; for the personal equation and the point of view of the observer play, perhaps, a larger part in the study of ore-deposits than in that of any other natural phenomena. One important purpose of my paper, and its publication at the time of the Washington meeting, was to call forth remarks from other geologists upon deposits with which they were personally familiar, or to lead them to re-examine such deposits with the idea of secondary enrichment in mind. Mr. Collins's remarks on Rio Tinto, which he has the advantage of personally knowing, are also interesting. With regard, however, to his suggestion-advanced as an apparent argument against our theory-that the re-precipitation of copper from cupric sulphate solution by pyrite can hardly take place there, since it would upset the commercial process, I would remark that, while he is undoubtedly right as to the fact, it does not militate against the reduction and re-precipitation of cupric sulphate in veins; since on the surface, as at Rio Tinto, there is free access of air, and consequently an excess of ferric sulphate, whereas in depth the ferric sulphate would have been mostly reduced to ferrous sulphate, and (there being no excess of acid to hold it in solution) the small amount of copper in the presence of an excess of iron sulphide would be precipitated either as sulphide or as native copper. To Professor Vogt's analogous remarks, that in his experience sulphuric acid is formed only in subordinate amount in the attack of sulphides by ferric sulphate, I would say that Dr.

Jan 1, 1902

By F. R. Hewitt

THE methods of mining talc are simple, and in western North Carolina are almost entirely by open cut and quarry. The larger part of the talc of this section lies in various-sized "veins" inclosed in quartzitic walls, the majority of which have by folding been thrown into a perpendicular position, or nearly so, and the exposed edges of which have been covered by debris from erosion of the mountain above. This covering of loose rocks and earth is from 5 to 25 ft. thick, and in most cases has to be removed because it is difficult to support. Sometimes the covering is heavy enough to "catch" and timber successfully, and in this case the talc can be worked out by the usual method of following the "vein," using stulls for holding up the walls until the vein is worked out, and then allowing the cut or drift to fall in. In some cases it proves more convenient to sink shafts and run drifts, following the talc "veins" until exhausted. The talc deposits of this section are badly broken and faulted both laterally and perpendicularly, and in some cases are found many feet below the level of drainage, necessitating pumping at considerable expense. . My own experience in mining talc has been that the chief point is to get a reliable "vein," and that then the mining is not as difficult, or any more so at least, than that of any common ore. If the. "veins" are pure talc it is simple; if the talc is admixed with foreign matter, such as tremolite in excess, or stains of iron or manganese, as is often the case, one had better abandon the deposit.

Jan 8, 1916

By Pol Duwez, H. E. Martens

The high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to bc cooled of a porous material', so that the cooling fluid can be forced through the pores, In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat, This method, referred to as ((sweat cooling," was pro- posed at the Jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very close control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of Pressure drop. Generally, the Proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequelltl~ the Permeability of the Porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1949

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By James R. Garvey

Coal reserves of the United States are enormous. Considered on the basis of proven reserves, and compared with reserves of other fuels, coal constitutes 88% of the proven recoverable energy resources of the nation. That includes oil, natural gas, oil shale and uranium used in burner reactors. Considered on the basis of "ultimate recoverable reserves", that is, those resources which can be extracted with improved technology and at somewhat higher costs and including those resources of all fuels not yet found but believed to be waiting discovery, coal still accounts for 75 % of the national total. In the U.S. hydrocarbon economy about 76% of the total energy needs are supplied by petroleum and natural gas and about 20% by coal. Domestic resources of oil and gas are running dangerously low, and assuming a continued hydrocarbon economy, the 20% supplied by coal may increase dramatically. Nearly a quarter of the petroleum consumed in the U.S. is imported. Natural gas is in shorter supply than petroleum and the problems of its importation seem at least as difficult as those of oil.

Jan 6, 1972

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, -1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2 CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws .in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were. tested for air circulation and air tightness and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering .these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, 1911, the fire area, in the Lowell mine continually increased. and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2, CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2 Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were tested for air circulation and air tightness .and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By M. C. Van Camp, J. D. Miller

Preliminary results are reported regarding the design and development of a pilot scale air sparged hydrocyclone for cleaning fine coal 590 pm (- 28 mesh) containing 24% ash and 1.6% sulfur. The principle of separation is the flotation of hydrophobic coal particles in the centnjugal field generated by the fluid flow in the air sparged hydrocyclone as discussed in another publication. This 152-mm (6-in.) hydrocyclone has a nominal capacity of 0.9 t/h (1 tph) and experimental results suggest that separations vastly superior to a water-only cyclone are possible. In addition the separation efficiency is as good, if not better, than that achieved with conventional flotation cells. For example, typical results indicate that 75% clean coal can be recovered at 15% ash leaving a tailing product of almost 50% ash. These experimental results coupled with the high capacity of the air sparged hydrocyclone (imagine a retention time for flotation of only two seconds compared to two minutes for conventional flotation) may represent a significant breakthrough, not only in coal preparation technology, but in the flotation of fine particles in general.

Jan 1, 1983

By G. D. Tranter

THE importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying tip pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

The fourth National Exposition of Chemical Industries will be held in the Grand Central Palace, New York, during the week of Sept. 23, 1918. Dr. Bacon, of the advisory committee, is now head of the Chemical Warfare Section of the National Army, and a member of General Pershing's staff. The coming Exposition will be the largest ever held, and it will be necessary to use four floors of the Grand Central Palace. The exposition is a war-time necessity, and regarding it as such, each exhibitor is planning his exhibit so that it will be of. the greatest benefit to the country.

Jan 8, 1918

C. W. WASHBURNE, New York, N. Y. (communication to the Secretary *).-We are indebted to Mr. Pack for his detailed description of a rapid method of estimating the oil reserves in large fields. Although his method will give only a rough approximation of the reserves, nevertheless it is much more reliable than the saturation method. The saturation method should not be used when any other method is available. The paper describes a generalized method, which is especially useful in estimating the total resources of a Nation or State. Properly it is a method of estimating the oil that can be extracted by common methods within a given period of time. It does not account for

Jan 10, 1917

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By Robert :H. . Lesemann

I recently gave a talk at a seminar on mine development in the Eighties. I had to present CRU&apos; s long-range market outlook for copper, lead, zinc, nickel, molybdenum and silver. In reviewing the recent history of each metal, and our projections, I tried to find some common pattern of behavior that could prove a guide in projecting future market behavior. When you sweep aside your input-output models and econometric equations, what you seem to be left with is this: "When a market goes through a prolonged period of price weakness, you can usually look forward to a period of considerable improvement. " "When a market goes through a prolonged period of price strength, you can always anticipate a prolonged period of price weakness." Stated another way, "The better things are, the worse they will get."

Jan 1, 1982

By L. S. Darken, H. A. Wriedt

In a previous paper,1 an experimental study of nitrogen dissolved in a cold-rolled ad heat-treated, low-carbon steel at 300° to 450°C yielded the equilibrium solubility relations and the concentrations of the two types of deject sites involved. In this paper, the probable identities of the defects that absorb nitrogen are restricted from the available evidence to screw dislocatioms for B sites, and to either micro crack surfaces or edge In a previous paper.&apos; we reported an experimental study of the excess nitrogen solubility in a low-carbon steel produced by a combination of plastic deformation and nonrecrystallizing heat treatment. The concentrations of the defect sites that absorb the excess nitrogen were measured in terms of their capacities for nitrogen. Also measured were the equilibria of nitrogen distribution among the sites. Several problems and questions arise from these measurements. We should like a physical identifi- dislocations for A sites. The concentrations of these defects in experimental steel specimens are estimated from the concentrations of defect sites. finally, the influence of chemical composition upon the nitrogen-trapping defects—the relative numbers generated in deformation, the relative numbers surviving as temperature is raised, the apparent numbers observed, and the distribution equilibria-is discussed. cation of the defects involved and of the two kinds of nitrogen-absorbing sites, called A and B types, upon those defects; the concentrations of the defects themselves could then be computed. We should also like to know how exclusively the findings apply to the "X steel" used in the experiments and to what extent they apply to cold-rolled steel given no subsequent treatment. By considering the data already given, together with results from a few specific tests which will be reported as they are invoked, we are able to eliminate some interpretations altogether and to secure an acceptable though limited interpretation from among the remaining possibilities.

Jan 1, 1965