Search Documents

By Ian William Wark, Alwyn Birchmore Cox

Different parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. Experimental Method The methods used have been described previously.l-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1939

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By G. R. Countryman, G. H. Thomas, I. Fatt

Miscible displacement in both thewetting and non-wetting phase has been studied in two-phase systems. Experimental data show that dispersion is a function of saturation and cannot be predicted from dispersion theory developed for single-phase miscible displacement. Some of the effect of saturation on dispersion is a result of the development of dead-end pores or a dendritic pore structure in multiphase systems. The presence of dead-end pores or dendritic structure is confirmed by pressure transient studies. INTRODUCTION Displacement by flooding with a miscible liquid is a possible means for recovering the estimated two-thirds of the oil that remains behind after primary production. The immense economic importance of a process that can recover such large quantities of oil has led to extensive laboratory studies of miscible displacement. As usual in production research, most laboratory studies of miscible displacement have not attemped to reproduce all of the conditions existing in a petroleum reservoir. In the early stages of investigation the need has been for information on the broad, basic principles of the phenomena involved in miscible displacement. The effects of overburden pressure, reservoir temperature, and wettability have been considered of secondary importance. However, one property of a petroleum reservoir which is expected to be of major importance and yet has been omitted from many laboratory studies is the presence of interstitial water. Two possible effects of interstitial water on the displacement mechanism in the hydrocarbon phase immediately come to mind. First, from the general1y accepted theory that capillarity governs the distribution of oil and water in porous rock one would expect that for water-wet rock the water will be in the small pores and oil in the large pores. A miscible displacement of oil carried out in the presence of water is operating in a pore size distribution shown in Fig. lb, whereas if the same test had been performed with only one phase present the pore size distribution is as shown in Fig. la. Although there is not yet a theory of miscible displacement which explains in detail the effect of pore size distribution, one would expect the differences between Figs. la and lb to influence the displacement efficiency. A second factor which may make a multiphase system different from a single-phase system is the presence in the multiphase system of dead-end pores or dendritic structure. Experiments of various kinds on reservoir rock have led to the belief that all pores in the network structure of a porous rock take part in conducting fluid during single phase fluid flow.1,2 There are then no dead-end pores and no fingers or dendritic structures containing stagnant fluid. In a multiphase system, however, the second phase may

By William Ian Wark, Alwyn Birchmore Cox

DIFFERENT parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter temperatures. It will be shown in this paper that the temperature is of considerable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation. EXPERIMENTAL METHOD The methods used have been described previously.1-4 In each test the clean mineral specimen was immersed in a solution prepared by adding the reagents in the following order: (1) sodium carbonate and hydrochloric acid as necessary to buffer the solution and to give approximately the pH value desired, (2) sodium cyanide, (3) copper sulphate, (4) ethyl xanthate, followed by (5) a final adjustment of pH value. After ½ hr. the mineral was tested for a xanthate film by bringing a bubble of air into apparent contact with the submerged polished surface. If true contact (spreading) was not obtained within ½ min. and after cleaning the surface by wiping with a small linen pad, it was concluded that the adsorption of a xanthate film had been prevented. Following the method already described (ref. 2), curves have been constructed such that for a solution ' composition corresponding to any point below the curve, contact between mineral and air is possible, whereas for a solution composition corresponding to any point above the curve, contact is impossible.

Jan 1, 1938

By B. H. Caudle, L. H. Silberberg

Reservoir depletion by natural water drive is typified by the movement of water from an aquifer into the adjacent oil-bearing formation. Prior studies of this type 01 water movement have generally neglected the resistance to flow in the aquifer and its effect on the movement of water into the oil bearing zone. A method for designing and operating scaled models of such reservoir systems is presented. Experimental data on a model of an edge-water-drive reservoir are shown and discussed. INTRODUCTION Most petroleum reservoirs derive at least a part of their productive capacity from water influx. This water may be injected from the surface or it may come from an aquifer adjacent to the oil zone. In either case, the reservoir engineer must be able to estimate the advance of the water as a function of either the elapsed time or the fluid produced. This paper describes a type of fluid flow model which includes the effect of viscous and gravitational forces in the reservoir and the surrounding aquifer. Natural water influx can be divided into three general (but widely overlapping) categories according to the direction of flow in the aquifer. These are shown schematically in Fig. 1. Fig. l(a) illustrates an edge-water-drive mechanism. In this case, water advances updip along the stratum but the movement of water is essentially horizontal and very little of the oil is actually underlain by water. The bottom-water drive (Fig. l(b)) is characterized by a thick aquifer underlying the oil zone. The water movement is generally vertical in the aquifer. The third category is illustrated in l(c). Referred to as the "thin oil column", this type of oil accumulation consists of oil over water in a relatively thin stratum. Fluid movement is horizontal in both the oil and water zones, except close to the producing well. One characteristic which all three of these types have in common is that part of the water flow takes place in the water invaded region of the oil reservoir while the remainder of the water flow occurs in the aquifer. The resistance to the flow of water usually will not be the same in these two regions. This occurs because the porous rock normally contains only water in the aquifer, while the water-invaded region always contains microscopic globules of bypassed oil (residual oil) which interfere with the flow of water through the rock. The production history of any type of a water-drive system is a function of two phenomena — where the water goes, and how it displaces the oil in the area invaded by the water. It is usually impractical to study these two phenomena at the same time. In most cases one type of analysis is used to predict the gross movement of water in the reservoir, while a different type of analysis is employed to determine the amount of oil to be recovered from the gross volume contacted by the water. The portion of the oil reservoir which is invaded by water is mainly a function of the resistances to fluid flow in the several parts of the flow system. This gross water influx in the three types of natural water drive typically results in water cusping to the production wells either from the side or from below (water coning). In 1747, Muskat described a greatly simplified mathematical model for predicting the area invaded by water in a bottom-water-drive reservoir.1 This model used the Laplace equation and suitable boundary conditions to describe the isopotentials and streamlines in the flow system. The use of this model assumes that (1) the reservoir rock is homogeneous in nature, (2) the oil and water mobilities are equal, (3) there is no oil flowing in the water invaded region, and (4) external forces — such as gravity — do not affect the flow. This method has been used for both natural water drives and water injection projects. In this, as in most models, the method of images is used to reduce the size of the model necessary to describe the reservoir. The assumption of equal viscosities and permea-

Jan 1, 1966

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

GWILLIAM H. CLAMER* (Philadelphia, Pa.).-Sulphur is not so detrimental in its effect if oxygen is also present, so that in sulphur-carrying bronzes and brasses, it is advantageous to maintain a certain percentage of oxygen. As a matter of fact, it would be possible sometimes to correct difficulties by actually adding oxygen. If the cathodes were charged directly into an electric furnace in a neutral or reducing atmosphere, a very high grade of copper would result by a simple melting operation. This would very largely eliminate the loss occasioned by melting in a reverberatory furnace. In such a furnace a large amount of slag is produced during the oxidizing stage of refining. Notwithstanding the fact that melting in an electric furnace might be somewhat more expensive than melting in a fuel furnace, the ultimate result would be a saving and the production of a very high grade of copper.

Jan 1, 1919

By W. B. Price

AT the New York meeting of the American Institute of Mining-and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."§ The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. PROTUBERANCES ON ADMIRALTY BRASS In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig.. 1a) and upon analysis was found to contain 66.66 percent. copper, 4.02 per cent. tin and .03 . per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and .01 per cent. lead. A sample of the shaggy-rough protuberances at the -very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had -revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation."

Jan 10, 1926

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

By Harvey Cline, Donald P. Ferriss

THE violent outgassing of commercial tungsten and other refractory metals when melted in an electron beam zone refining apparatus1"3 is dealt with experimentally by one or both of two approaches. One is to provide a suitable emission current control1,2 the other is to purify the metal in the solid state before melting.4 The first of these is usually sufficient, but the authors chose also to investigate the source of the troublesome gases and to devise means of solid-state purification. Some further insights into the use of tungsten as a structural material at temperatures near its melting point were also revealed in the course of the work. One may speculate on the causes of gas formation in tungsten at high temperature by inferences from the literature and an examination of the impurities in commercial wire. Davenport5 observed microporosity in both tungsten and molybdenum filaments heated to several hundred degrees below their melting points. Studying the function of oxygen in molybdenum welds, Perry, Spacil, and wulff8 attributed similar porosity to the disproportionation of Moo2 to molybdenum metal and Moo3. Tungsten dioxide also disproportionates7 above 2000oC to yield WO3 vapor at considerable pressure. Commercial tungsten contains some 5 to 20 wt ppm O and a similar concentration of carbon depending on the details and precautions of processing. Therefore, evolution of CO is also a strong possibility as a source of gas at high temperatures. Furthermore, even for activities in the order of 0.01, it may be calculated that the pressure of CO at 3000°C would be over 4000 psi, which is in excess of the tensile strength of tungsten at this temperature.9,10 Powder metallurgy tungsten contains some 0.02 pet Fe and 0.002 to 0.005 pet of the elements Ni, Si, Al, Ca, Mn, Mg, and Mo; at temperatures over 2800°c, therefore, these elements will exhibit appreciable vapor pressure, though small compared to that of WO3 and CO. Some of these impurities may react to form high-pressure monoxides such as SiO and A10. Finally, dissolved and occluded nitrogen is an ever-present source of high-pressure gas. Commercial Type 218, General Electric filament wires, 0.025 in. diam, were heated by resistance in 10 -4 mm of Hg and in argon or hydrogen at pressures from 50 µ to atmospheric. For temperature determinations in vacuo, the Jones - Langmuir8 current-temperature relationship was employed. For gaseous atmospheres, the burn-out temperature was assumed to be the same as in vacuo so that a small, constant correction could be made for temperatures below burn-out conditions (i.e., local heating to failure). Several dozen experiments may be summarized by pointing out some structural observations. At 3050oC in 1 atm of A, porosity is very evident after 30 min, as shown in Fig. 1. For the section in Fig. 2, failure occurred 200°C below the melting point and many voids have grown in the grain bound-

Jan 1, 1962

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

By L. C. Graton

Civilization did not begin until metals became the material of tools, implements and machines. - RICKARD, Man and Metals. HISTORY is no more an end in itself than is a backsight the sum total of a survey. This Institute may view with satisfaction the remarkable development of the mineral industry since its founding three score and fifteen years ago, its own enlarging service to that industry, and the contribution thus made toward the enhanced welfare, opportunity and mutual understanding now in greater or less degree reaching and benefiting all peoples of the globe. But neither this professional society nor the dynamic mining industry as a whole wishes on this anniversary to direct its gaze chiefly toward the past. The foremost purpose of historical review should be to throw into clear perspective the strong points and the defects in the forward march thus far, primarily as the basis for conceiving and designing a still sounder progress henceonward. At various times since the Institute&apos;s founding, the theories of ore deposition have been considered from the historical view point.l-7 For the present occasion it seems fitting to lay prime emphasis on the practice and utilization of geology in its varied relations to the problems of the mining industry. It is hoped that the reader will understand and accept the degree to which the whole is sampled by parts familiar to the present writer, and the disproportionate attention to thought and achievement within the United

Jan 1, 1947

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By C. A. Lemke

The ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from the company&apos;s mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent, of the total ore. These three minerals vary considerably in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver & Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment. Gravity Concentrator The gravity concentrator has a capacity of about 465 tons in 24 hr. The mill buildings are of wood. The mill was built in 1905 to handle approximately 90 tons in 24 hr.; since that time several additions have been built and various changes have been made in the flow sheet. The last extension, which raised the capacity of the mill to its present level, was built in 1915. The additions to the mill building have not kept pace with

Jan 1, 1926

On Friday, Jan. 17, the thirteenth impression of the Perkin Medal was presented to Dr. Frederick Gardner Cottrell, at a meeting of the New York Section of the Society of Chemical Industry, held at the Chemists&apos; Club, in New York City. The presentation address was delivered by Dr. C. F. Chandler, Senior Past President of the Society. The medal was awarded for the recipient&apos;s work in the electrical precipitation of suspended particles in gases. Dr. Cottrell&apos;s career, which is so familiar to members of the Institute, was sketched by Dr. Chandler. He told at some length of the experiments leading up to the final solution of electrostatic precipitation, which has done so much to solve the problem of smelter smoke. The principal interest in Dr. Cottrell&apos;s speech of acceptance lay in his remarks about helium, the production of which has been so reduced in cost that it has practically supplanted the use of hydrogen for inflation purposes in war balloons. He said: "Two or three weeks after war was declared in 1917, Dr. R. B. Moore attended a meeting of the American Chemical Society in Kansas City. At the general session, Mr. Seibel of the University of Kansas, gave a paper on krypton and xenon in some of the natural gases of Kansas. At the end of his paper, he expressed regret that at such a time, when everyone was thinking of war problems, his paper was of a purely scientific nature and had no practical bearing on the war. Dr. Moore immediately got up and said that he did not agree with Mr. Seibel. The presence of helium in those wells could, and should, have a very practical bearing on the war, as this gas could be extracted in quantity from the natural gas and used for balloons and Zeppelins. He pointed out some of the natural advantages of helium over hydrogen, and quoted Sir William Ramsey&apos;s letter advocating the use of helium for airships. The general attitude of those present was one of scepticism, so he finally asked Dr. Cady for his opinion who stated that he believed-the thing could be done, but was very doubtful whether it could ever be made practical on account of the cost." Dr. Moore in a letter wrote: "That same day I talked to Dr. Parsons, who was present at the meeting and was returning to Washington almost immediately. I told him what had happened, and that I believed the matter should be taken up by the Bureau at once and presented to the War Department. He promised to do this as soon as he got to Washington; and I know that he did take the matter up with other Bureau officials." Dr. Cottrell continued in part: News of Ramsey&apos;s suggestions also reached this .country through other channels and eventually came to our attention. Professors Satterly and Patterson of the University of Toronto commenced experimentation of the subject Jan. 1, 1916. Col. G. A. Burrell, who headed the research department of the Gas Warfare Service at the American University, tells me that Cady&apos;s experiments had also suggested similar possibilities to him.

Jan 3, 1919

By Richard Hunt

BINGHAM has produced 6 per cent. of this country&apos;s copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham&apos;s silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. Bingham is on the eastern flank of the Oquirrh range 30 miles south-west of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads.. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep-an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century.

Jan 3, 1924

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.&apos; In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944

By James K. Stanley

Preferred orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.&apos; In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurnical -literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanicai properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important information, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational understanding of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required—it is only necessary to punch or machine a I-in. disk of the sheet material and insert it into the testing device.

Jan 1, 1944