Search Documents

By Jay Carpenter

THIS paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator. This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with aTrent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. .These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and. delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 8, 1915

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes.

Jan 1, 1950

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By AIME AIME

ON Tuesday afternoon, Feb. 17, a large and interested audience gathered in the auditorium of the Engineering Societies building to take part in the gold supply symposium that had been arranged for by the Mining Geology Committee. Waldemar Lindgren presided over the gathering and after brief introductory remarks on the international situation as regards lead, silver and gold, called on John Wellington Finch to present an oral abstract of the paper, "Sources and Trends in Gold Production," by R. J. Grant, director of the Mint, and. J. B. Knaebel. This ' paper reviewed the gold production of the world, by countries, since 1845, from the statistical viewpoint, leaving to the later speakers discussion of the statistics.

Jan 1, 1931

By T. A. Rickard

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for these they use unnecessarily The work will begin [on] Saturday. The work will begin [on] Saturday. `Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary .. . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. I suggest: ". . . and merchandise] was sold to all the employees on a strictly cash basis.". The verb `be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat tie auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By B. W. Frazier

Jan 1, 1882

By Francis Church Lincoln

I. SITUATION AND SURROUNDINGS. THE Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chinacates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the station by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion-a distance of about 15.5 miles-and then entering the mountains crosses the Sierra to Promontorio-a further distance of 11.5 miles¬making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Ives, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Melchor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-July, August and

Jan 1, 1908

By R. L., Fullman

During the past year there have been a number of significant investigations that have furnished evidence on the driving forces governing grain growth and on the role played by boundary impurities. Thus Burke has shown that in high purity alpha brass the rate of grain growth in the earliest stages is approximately inversely proportional to the existing grain size. This relation agrees with one derived by Zener assuming that surface energy was the driving force in grain growth. Also in confirmation of the surface energy hypothesis, Burke found that growth virtually stopped when the grain boundaries or even only the grain corners were melted.

Jan 1, 1949

By Paul Queneau

FEW of us who waded ashore on the Norman beaches realized the importance of coal to a successful invasion. General Eisenhower and his staff had been aware of the essential need for coal and an able Solid Fuels Section had been set up under the direction of Colonel Robert P. Koenig, of Indiana. This organization met the requirements of the invading armies on their march to the Rhine. East of the Siegfried Line enemy territory, the Army Engineers were called upon for assistance. When the Engineers were advised that, in addition to their normal duties, they were to occupy and place in operation the coal mines in the Twelfth Army group area, plans were drawn up overnight and action was initiated immediately. The Sixth Engineer Special Brigade, a versatile outfit which made a notable record D-Day on Omaha Beach, was selected to handle the operation. Within 48 hours of the new assignment an advance command post was set up cm the west bank of the Rhine at Homberg, just below German-held Duisburg. The 368th Engineer General Service Regiment was assigned to the Brigade, and the British 44th Pioneer Group, including specialist personnel, was also attached. This large British unit was added because most of the mines would shortly come within the British zone of

Jan 1, 1946

By Francis Church Lincoln

I. Situation and Surroundings, The Promontorio mine is situated at the northern end of the Sierra San Francisco de Coneto, in the town of Promontorio, Partido of El Oro, State of Durango, Mexico. As shown in the sketch-map, Fig. 1, the nearest railroad station is Chin-acates on the Mexican International Railroad, 82 miles north of the city of Durango. The mine is 16 miles north of the sta-tion by air-line. It is reached by means of a good wagon-road which first crosses the Guatimapé Plain, passing the ranches of San Antonio and San Julian, to Estacion—a distance of about 15.5 miles—and then entering the mountains crosses the Sierra to Promontorio—a further distance of 11.5 miles— making in all a distance of 27 miles by road from railroad to mine. Promontorio is just beyond the summit of the range, at an elevation of about 8,000 ft. above sea-level, or 1,350 ft. above the Chinacates station. The Castillo de San Francisco, the highest peak in the Sierra, has an altitude of 10,000 ft., and the Promontorio road crosses the summit of the ridge at an elevation of 9,000 ft. by a pass just below this peak known as the Puerto del Almagre. The Promontorio mill is situated at Santa Inés, 2 miles by tram or 3 miles by wagon-road to the north of Promontorio and about 600 ft. lower. The Sierra San Francisco de Coneto decreases in height towards the north and west till it comes to an end at the Mel-chor Arroyo on the ranches of Melchor and Ramos. Beyond this arroyo another range, the Sierra de la Candela, begins. In the vicinity of the Promontorio mine the hills are very rugged and the surface is furrowed by ravines which contain running streams during the rainy season-—July, August and

Jan 1, 1908

By Raymond E. Zimmerman

The Swirl Cyclone developed in Japan, although based upon the same principles as the standard cyclones for heavy-media or water-only cyclones for cleaning coal, is novel in that it is invested with the apex on top, discharging rejects at the top, and clean coal at the bottom. It also uses a variable air vent tube for controlling the vortex. Tests conducted indicate that its efficiency is not only as sharp as standard cyclones but it also performs using a much coarser grain magnetite, promising higher magnetite recovery. The author describes the results of tests conducted in Japan on a very difficult coal.

Jan 1, 1979

By FREDERICK LAISY

A NUMBER of new plants for the treatment of copper ores were completed or under construction during the year. Among these may be mentioned the plants of the International Nickel Co., those of the Hudson Bay Mining and Smelting Co. and of the Roan Antelope Copper Co. Three copper re- fineries have been constructed, one at El Paso, Tex., and the other two in Canada. Two more are projected, one in France and one in England. The International Nickel Co.'s plant consists of an 8000-ton concentrator and a smelting plant containing thirty 10-hearth Herreshoff roasting furnaces, five reverberatory furnaces, and eight Smith-Pierce converter5 . The smelting plant is estimated to have a capacity of 5000 tons of ore or concentrate per day. The roasters are superimposed on the reverbratory furnace plant. As a consequence of this arrangement, the furnace building is unusually high. being 183 ft. from yard level to highest roof elevation.

Jan 1, 1931

By J. C. Bayles

Jan 1, 1886

By Raymond E. Zimmerman

Abstract-The Swirl Cyclone developed in Japan, although based upon the same principles as the standard cyclones for heavy-media or water-only cyclones for cleaning coal, is novel in that it is invested with the apex on top, discharging rejects at the top, and clean coal at the bottom. It also uses a variable air vent tube for controlling the vortex. Tests conducted indicate that its efficiency is not only as sharp as standard cyclones but it also performs using a much coarser grain magnetite, promising higher magnetite recovery. The author describes the results of tests conducted in Japan on a very difficult coal.

Jan 2, 1978

By John S. Alexander

Jan 1, 1880

By H. M. Cyr, T. F. Steele, C. W. Siller

The development of a new metallurgical roasting device is described. It consists of a refractory column into which air is injected at various levels, forming several superimposed fluidized beds with no supporting grates. When pelleted zinc sulphide concentrates are charged, the roasted product needs no further sintering before reduction to metal. WHEN a gas such as air is blown upward with increasing velocities through a loose mass of solid particles, marked changes in the physical behavior of the particles are noted. At first, when the velocity of the gas is insufficient to support any of the solid, the mass constitutes a "fixed bed." As the gas velocity increases until the pressure drop through the bed approaches the effective weight of the bed per unit area, the bed expands until the solid particles are supported by the air rather than by the lower particles. Some vibration of the particles becomes apparent, but little mixing occurs. This condition is called a "quiescent fluid bed." A further increase in gas velocity imparts more separation and more motion to the individual particles until a condition of turbulence is reached. This "turbulent fluid bed" resembles a rapidly boiling liquid with the characteristic highly agitated diffuse surface and many small eruptions of the boiling mass. Different degrees of turbulence can be generated and all produce excellent mixing. The final stage occurs when the gas velocity becomes so great as to create a "dispersed suspension." Here no surface of the mass is defined and the gas carries solid particles out of their original positions. These changing conditions of fluidization have been studied carefully and pertinent nomenclature standardized by a committee of the American Institute of Chemical Engineers.' Many mathematical analyses2-3 have been made of the forces acting in a fluid bed. These analyses are invaluable, especially for the design of column sizes and selection of equipment. However, in a metallurgical process involving solids of many sizes with changing densities, varying temperatures, and changing gas compositions within the bed, calculations based on theory become approximate. Optimum operating conditions then are best determined experimentally. Many applications have been made of the principles of fluid-bed action by mechanical, chemical, and metallurgical engineers. Especially when good con- tact between reacting solids and gases is desired, very effective results are obtained from fluid beds. They permit excellent temperature control and uniformity throughout a mass of solids in fluid action. Heat transfer to walls and any coolers is high, and fast reaction rates are attained because the solid surfaces are continuously swept clean. The main disadvantages of fluid-bed operations are the danger of short-circuiting in a single bed, danger of incipient sintering which stops action, the necessity of avoiding large changes in particle size or density during roasting, and dust losses when particles of the charge are carried out with exit gases. In the metallurgical field the roasting of sulphide ores to form oxides and sulphur dioxide appears to combine several operating conditions which can be achieved to advantage in a fluid bed. Roasting involves a solid-gas reaction where a high reaction rate is necessary for high capacity, where good temperature control is important in order to prevent sintering, where good heat transfer is needed, and where the density of the solids, when changing from sulphides to oxides, is not largely changed. Short-circuiting, however, constitutes a major problem when a single fluid bed is used. Because of the turbulence of the bed, an entering particle may be in the region of the discharge before it is roasted. Hence, to attain a satisfactorily low sulphur in the calcine, a long average residence time with correspondingly low capacity is required. The solution to this difficulty is the use of multiple stages, which in the conventional fluid-bed design requires separate hearths with feed and discharge mechanisms for each stage. A further practical difficulty in fluid-bed roasting of flotation zinc concentrates is their fine particle size which makes a true fluid action without excessive carry-over of dust very difficult to attain, especially when the large air volumes necessary for high capacity are used. A New Design After considerable experimentation in the laboratory and on a semipilot-plant scale, a new method and equipment for roasting were devised which provided a unique solution to these problems. A detailed account of this development appears in the patent literature," and many of the variations of this development reported herein are the subject of

Jan 1, 1955

By AIME AIME

ON JULY 12, 1921, S. S. Arentz, representative at large from Nevada, introduced in the House of Representatives, under the number H. R. 7736, a bill to revise, amend and codify laws of the United States relating to the location of mining claims on public domain, and other purposes. This bill had been drafted by a committee of consulting engineers of the U. S. Bureau of Mines. The immediate purpose of this introduction in Congress was to make it avail- able for general information and discussion. In pursuance of this purpose Mr. Arentz issued the following circular: This proposed codification and revision of the mining laws of the United States as received from a committee of mining and metallurgical engineers appointed by the Director of the United States Bureau of Mines was introduced in the House of Representatives by the undersigned (who has operated and developed mines throughout the West for many years). It is submitted to prospectors, mine operators and mining engineers, all of whom are affected and vitally interested in the subject with the hope that they will give this bill their careful consideration and study.

Jan 1, 1921

J. E. Johnson, Jr., Glen Wilton, Va. (communication to the Secretary*):—Mr. Meissner announces early in his paper that one of its purposes is the discussion of my paper entitled, Notes on the Physical Action of the Blast-Furnace,' with which he disagrees in part; and as the second stage of the discussion of this important subject has centered around his paper, some reply by me may not be amiss. Unfortunately, Mr. Meissner has not indicated a single statement or conclusion in my paper that he wishes to controvert; but as there is evidently a difference of opinion between us I will disregard this fact, and will discuss those conclusions of his that seem to me not to be justified by the facts of general practice, or even by the data which he produces to support them. Let me say, however, that I am a believer in the dry-air

Jan 1, 1908