Search Documents

By E. F. Sumner, C. K. Eilerts

A partial differential equation was developed and programmed to compute the cumulation and flow of the liquid phase of a gas-condensate fluid. It was found that such cumulation near the wellbore may attain saturations permitting liquid flow within periods of the order of 1 day. The radius at which this saturation obtains advances toward the external reservoir boundary with continued recovery, although it may move only 2 to 5 percent of that distance during the productive life of the well. This relatively high saturation can cause a serious dimunition in delivery capacity. The pressure dilferential required for flow of gas through a formation with such saturation may be as much as three times greater than the corresponding differential in a formation where saturation is less than 2 percent. Because of the radial geometry, total reservoir pressure differential required for flow with a zone of relatively high liquid saturation about the well was indicated to be two to three times greater than without the saturation. INTRODUCTION A computing program developed by the authors 1 to integrate the partial differential equation for transient radial flow of gas-condensate fluids required a prevalued function, W(Po) = kD(p0)/M(p0)z0(Po).......(1) related to cumulation of condensate in pores of the reservoir as pressure declines. Methods were available for relating mobility to saturation, saturation to liquid-vapor volume ratio, liquid-vapor volume ratio to pressure and, hence, mobility to pressure to obtain W(pD). However, certain assumptions had to be made in advance of program execution concerning movement of the liquid phase and change in radial distribution of liquid saturation as recovery progressed. Because reservoir fluid mobility and related pressure gradients are markedly dependent on liquid saturation, it was desirable to eliminate the necessity for these assumptions and in this respect improve the reliability of a result obtained by integration. Experimental research was begun to determine the relationship of variables that control the reservoir flow of low liquid-vapor ratio fluids. With the porous medium partly saturated, permeability to a two-phase flowing fluid could not be measured because the viscosity was unknown. Viscosity could not be measured without knowing permeability of the liquid-containing medium; but mobility, the ratio of permeability to viscosity, was measurable. This property, and liquid-vapor volume ratio of the flowing phases, have values determined by nature of the fluid and porous medium and, in addition, were found to be pressure, velocity and saturation dependent. A program developed by Kniazeff and Naville 2 for computing multicom-ponent, two-phase flow used polynomials to represent saturation dependence of permeabilities for gas and for liquid phases, and an effluent viscosity constant under reservoir conditions. The authors developed a program based on a partial differential equation of similar mass balance origin but designed to represent distribution of an unlimited number of components between gas and liquid phases utilizing the experimental information available as to variable dependence. Attention was given to liquid-vapor volume ratio of the flowing phases, a property which is essential as a liquid saturation boundary condition. A program for computing implicitly saturation increase at uniform intervals along the drainage radius was combined with an existing program for calculating pressures, and the two were used alternately in an iterative solution for both saturations and pressures. The function W(pD) needed for calculating pressures was replaced by the ratio of mobility to compressibility factor. BASIC EQUATIONS The partial differential equation for calculating

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By D. N. Witman

One of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross-sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance of a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure, in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the e1etrical resistance of ordinary cast iron. The metal specification is as follows: Per Cent. Silicon............................................. 2.40 to 2.60 Sulfur............................................. Under 0.05 Phosphorus......................................... Under 0.08 Manganese......................................... Under 0.40 Total carbon....................................... 3.60 to 4.00 Nickel............................................. 4.00 to 5.00 Copper............................................ 0.50 to 0.70

Jan 1, 1922

By H. L. Hazen

The uranium mill at Gunnison, Colorado, started crushing ore Dec. 31,1957, and has now been operating four months. The acid leached ore is washed by counter-current decantation through a system of four classifiers and four thickeners and most of the dissolved uranium reports in the overflow from the first washing thickener. This uranium is extracted from the aqueous pregnant solution by solvent extraction using di-2-ethyl hexyl phosphoric acid and tri-butyl phosphate dissolved in a high-flash-point kerosene as the extracting organic. The pregnant organic is then stripped with soda ash solution. The uranium bearing soda ash solution is filtered to remove insoluble carbonates and any sediment reaching that part of the circuit. The clarified carbonate pregnant solution is then acidified to 3 pH, heated to 180°F to drive off the last traces of CO2, and the uranium finally precipitated as yellow cake with MgO.

Jan 11, 1958

By A. Brown

RAPIDLY rising world demand for mineral products has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations. In recent years the Mines Branch of the Department of Mines and Technical Surveys in Canada has conducted such an investigation. This report of the work is primarily concerned with stress problems in some Canadian coal mines and, in particular, with mine bumps. Mines Branch investigations of this and related problems are carried out by a small team of mining engineers and physicists who, with assistance from geologists, pool their special skills in an integrated program. These Canadian investigations combine a field and laboratory approach. Since data obtained under contrasting mining conditions allow useful comparisons of ground behavior under stress, this article will present data gathered under a wide range of Canadian coal mining conditions. Two contrasting longwalls in eastern Canada will be discussed and two dissimilar pillar extraction operations in western Canada. Locale of Observations In eastern Canada observations are being made in the collieries at Springhill, Nova Scotia. The district's No. 2 mine, which has a history of bump occurrences dating back to 1917, is currently being worked at a depth of 4200 ft. The mining method is longwall retreating along the strike and the practice is to retreat three walls in line, each about 350 ft long. There is no machine cutting or shooting—the coal is hand-picked and hand-loaded onto face conveyors. There are three rows of hardwood chock block supports parallel to the coal face. These supports are built during the two daily coal loading shifts, and the rear line is withdrawn during the midnight shift. The goaves are partially packed by stone midwalls 12 ft wide which are built forward daily in step with the face advance. The seam dips at 15° and averages 9 ft of strong, well cleated bituminous coal enclosed in competent beds of shales, sandy shales, and sandstones of Carboniferous age. The bumps rarely disturb the retreating longwall faces but manifest themselves as violent upthrusts of pavement in the levels leading to the walls. Observations have also been made in Springhill's No. 6 mine, which operated in a 5-ft seam of coal at a depth of about 2500 ft. Although No. 6 mine was

Jan 1, 1959

PUGET SOUND SECTION SIMON H. ASH, Chairman, I. F. LAUCKS, Vice Chairman, CHARLES SIMENSTAD, Sec.-Treas., 425 Lyon Building, Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT. The Puget Sound Section met at the Arctic Club, Seattle, Wash., on Jan. 20, 1917. Sixteen members and five guests were present. Dinner having been served, the meeting was called to order. A letter from secretary of Associated Engineering Societies was read, requesting payment of this section's assessment to the quarterly budget, and upon motion it was voted that the Secretary-Treasurer be instructed to pay this assessment. It was moved and carried that this section join with the Chemical Society in a meeting. At the, close of the business meeting, Mr. Asa C. Baldwin gave an illustrated lecture on the "Alaska Boundary Survey." On Feb. 24, the Puget Sound Section again held a meeting at the Arctic Club, 16 members and three guests being present. Chester F. Lee, as member of a committee representing this section in the joint council of the Associated Engineering Societies, reported that by lots it had been decided that the term of service of said committee would be as follows: Chester F. Lee, two years; George. Watkin Evans, one year. Following adjournment of the business meeting, Prof. Joseph Daniels, of the University of Washington, delivered a very interesting lecture on "Milling Practice of The Alaska-Castineau Mining Company." CHAS. SIMENSTAD, Secretary.

Jan 5, 1917

By Maurice Ewing, L. Don Leet

The most important quantitative method in seismic prospecting by refraction shooting is the method of profiles. A profile is established by firing a series of charges at various points along a straight line which terminates at the seismograph. The same data are obtained by repeatedly firing charges at one place and recording at a series of stations along the line of the profile. The quantities which are measured are the distance x from each firing position to the seismograph and the time t required for the first disturbance from each explosion to travel to the seismograph. These data are used in plotting the familiar time-distance graph. The only time-distance graphs that will be considered here are those obtained in localities where the velocity of propagation depends solely on the depth beneath the surface; that is, where there is no slope in the subsurface. The essential calculation to be made from such a time-distance graph is the determination of P(x), the maximum depth of penetration of a disturbance coming to the seismograph from a firing point at the distance x from the instrument. If the time-distance graph consists of a series of straight lines, as is often the case, the penetration P(x) can be calculated by means of formulas which appear in almost every description of seismic prospecting.' Until the present, however, the only formula that has been available for calculating P(x) for time-distance graphs which are smooth curves is one which requires an arbitrary assumption regarding the law of velocity increase with depth.2 The practice in these cases has been to approximate the curve by means of a number of straight lines and then to apply the ordinary straight-line formulas. This method clearly can yield accurate results only when a sufficiently large number of straight lines is used. The labor of computation increases rapidly when the number of lines is increased, so too few lines often are used. Further than that, there is a strong tendency to overlook the approximate nature

Jan 1, 1932

By K. E. Barrett

Exxon owns a uranium mill and holds two mining leases in Live Oak County, Texas, about halfway between San Antonio and Corpus Christi. The properties make up the Felder Uranium Operations which was reopened earlier this year. Exxon held an oil, gas, and other minerals lease on the J. C. Felder tract, which was adjacent to a relatively shallow uranium discovery by Susquehanna-Western, Inc. on the Marrs-McLean lease immediately south of the Felder property. Drilling in 1967 and 1968 confirmed the presence of reduced uranium mineralization in the basal sand unit of the Oakville formation on the Felder tract, which formed the major part of the roll-front deposit. In 1969 Exxon and Susquehanna-Western, Inc. entered into a sale and purchase agreement which provided for Susquehanna to mine and process Felder ore and purchase recovered uranium. Susquehanna moved an alkaline-leach mill from Wyoming, erected it on the Ray Point property, and placed it into operation late in 1970. Susquehanna mined and processed ore from the Felder and McLean properties through March 1973. Susquehanna ceased operations in March 1973. Exxon then acquired the mill and mill property. Exxon also purchased the mineral rights to the McLean lease, re-negotiated a mining lease for that property, and carried out shut-down programs for the mining and mill areas in the fall of 1973. The project was put on a standby basis until late 1973, when Exxon initiated mine feasibility studies for the project. MINE PLANNING EVALUATION The feasibility study for reopening the Felder Project began in late 1975 and was not completed until late 1976. I will discuss several areas of the feasibility study that required additional work prior to making the decision to renew operations. Ore Reserves Preparations for estimating the ore reserves began with the re-evaluation of more than 1500 natural radioactivity logs from exploration and pre-development drilling that had been completed on the property. These gamma ray logs of non-core rotary drill holes were the principal source of data used in making the estimate. Chemical assays of cores from the deposit were also used in the reserve determination. Electric resistivity and self-potential logs were made along with the gamma ray log. In December 1975 an additional core drilling project was undertaken to confirm the in-place density and radiometric equilibrium characteristics of the ore deposits. Comparison of chemical assays of cores with the U308 values calculated from the logs showed that the unoxidized ores were in radiometric equilibrium. In contrast, cores from anomalies occurring in near surface, weathered, and oxidized zones were in radiometric disequilibrium. Several important decisions were made in developing a mine plan or schedule of production from the Felder and McLean ore bodies. Disposal of Produced Mine Water: The ore bodies of the Felder Uranium Project occur at a point below the ground water table. The ore zones to be mined must first be dewatered to allow removal of mineralized material. In the open pit operations, this is accomplished by maintaining a perimeter ditch around the periphery of the open pit, allowing the interior of the pit to drain and collect into a sump and be pumped from the mine. In addition to anticipated water production from future mining operations, approximately 200M gallons of water was contained in three open pits left from prior mining operations. In two of these existing pits, the water was to be removed and disposed to allow for planned backfilling of waste material into these pits. The third pit would also have to be drained to allow continued mining of an area left from the prior operations. Essentially no ground water information was available for this area. The only data available was water production history from Susquehanna's mining operation. Two water wells were drilled early in 1976 on the Felder lease for use in obtaining hydrological data. A long term draw-down test was performed by pumping one water well and measuring water level drawdown in both the pumped well and the observation well. From these data, values for permeability and storage coefficient were calculated. These data were then used in modeling the aquifer to allow calculation of water influx into the mining area versus time. Once a schedule of water production, including the stored volume in the existing pits was calculated, alternate solutions for disposal were evaluated. The first system evaluated was a series of deep injection wells. The wells were designed to inject at a depth of approximately 3500 feet. Again very little information concerning reservoir characteristics of the receiving sand units was known. Using assumed values for reservoir permeability and storage coefficients, an injection well system was designed to allow for disposal of produced mine water. The biggest

Jan 1, 1979

By Joseph B. Umpleby

WHEN the Cushing field flooded the oil market in 1914 and 1915 with a daily output equal to nearly one-third of the world's production, the situation was soon corrected by increased consumption, and the price of crude oil rose from 45 c. per barrel in, February 1915 to $1.10 in December of the same year-the highest price paid in the Mid-Continent field up to that time. The intensive search for oil during the following seven years failed to disclose a single new ,field equal to Cushing, and many observers concluded that the rapidly increasing number of wells contributing to the world's output, each declining roughly 20 per cent. a year, combined with the rapidly increasing con¬sumption of petroleum, made it highly improbable that any field would; be found again sufficiently large to seri¬ously affect the oil market. That seven exceptional fields should then be discovered simultaneously is a remarkable coincidence. Long Beach, Santa Fe Springs, and Powell, each exceeded Cushing in daily output and reached the apex of their production during a year when Burbank, Tonkawa, - Smackover and Huntington Beach each contributed several times the daily output of the average new pool. This unexpected and tremendous flood of flush production could only have the effect of depressing price and greatly adding to stocks throughout the country. It was particularly depressing in the Mid-Continent as the new oil from California proved of attractive refining grade and because of cheap transportation by water easily undersold Oklahoma crude in the eastern markets.

Jan 1, 1924

By J. Mackintosh Bell

The history of the South Lorrain mining camp is given and comparisons are made between the local topography and general geology and that of the Cobalt camp. The character of the silver-bearing veins and their analogy to those of Cobalt are given and the theory regarding the cause of the deep seated oxidation in South Lorrain, particularly at the Keeley Mine, is outlined. The oreshoots are described, also the conditions governing their occurrence and position. The mining and metallurgical practice are briefly considered. IN THE numerous districts subsidiary to Cobalt, and carrying mineral deposits similar in character to that world-famous mining camp, the most interesting recent developments have occurred in South Lorrain. The district, the center of which lies about 16 miles southeast of Cobalt, was the scene of a rush in 1907 but, in spite of the success of the Wettlauffer mine, the locality soon lost its popularity, largely on account of the unsavory early history of the Keeley mine. In recent years, following the successful development of this property by the London operators, who acquired it from the liquidator of the original company, and the later conspicuous progress made on the properties of the Mining Corporation contiguous to the Keeley on the north, the district has again come into prominence and, at present, is doing much toward maintaining the gradually declining production of Cobalt itself. Apart from the Mining Corporation of Canada and the Keeley Silver Mines Limited, the principal concerns now operating in South Lorrain are the Lorrain Consolidated, the Trout Lake Mines (operated by English interests associated with the Mining Corporation) and the Canadian Lorrain Silver Mines (operated by the Huronian Belt Co., of London). A number of minor prospects are also active. The Wettlaufer and Currie, on both of which considerable work was done some years ago, are now closed.

Jan 1, 1924

By Philip Morse

THE Australian lead-smelting plants began to use charges carrying high zinc percentages somewhat earlier than was common with American plants. When lead smelting first started in Australia the immense deposits of oxidized lead at Broken Hill were available but later these oxidized ores became exhausted and were replaced by sulfides. This was before the days of flotation and these sulfides when concentrated carried about 1 per cent. of zinc to 6 per cent. of lead. The works of the Sulphide Corpn. at Cockle Creek was perhaps the pioneer in high-zinc slags but the Port Pirie plant of the Proprietary Co. was a close and very able second and has continued the work to the present time. The Cockle Creek lead furnaces remained in operation until shortly after the war when most of the Broken Hill companies combined and took over the Port Pirie plant to treat their concentrates. As it was the practice both at Cockle Creek and Port Pirie to carry 20 per cent. or more of lead on the charge, it was found that under these conditions of large amounts of zinc in the charge, good roasting was absolutely necessary and matte production was unwise. The Huntington-Heberlein system of roasting was introduced and later the Dwight & Lloyd process. In this way, by roasting the sulfide portions of the charge as thoroughly as possible and making no matte, a method of smelting was developed where the slag over long periods carried as high as 20 per cent. ZnO without serious furnace troubles, and slags carrying even up to 33 per cent. ZnO have been reported. The zinc slags were not very different in appearance from the ordinary slags produced in American practice except that they gave off more smoke and fume on tapping. The slag usually ran hot and freely, coming from the tap in a full stream. Normally there was little crust on the sides' of the furnace and the tuyeres gave no trouble though they were always rather dark.

Jan 1, 1929

By S. A. TAYLOR

AN EDITORIAL on the Strike Situation in the Coal mining industry in the New York Evening Post of Nov. 4, 1919, gave what purported to be statistics of the Department of Labor, for a period of two weeks, which showed an average for the year, based on these two weeks, of 32% hours per week. This mode of arriving at the number of hours per week, while not accurate, is not so far off from the facts as to call for any special comment. The report of the U. S. Geological Survey, Department of Coal Statistics, give so the number of days worked in 1917 as 243; reducing the same to hours per week, assuming 8 hours per day, shows a weekly operation of mines at an average of 36J4 hours. But this assumption is not exactly correct, for the reason that it is not very often that the miners work the full 8 hours per day. There are many explanations for this, but it is not pertinent to this statement to discuss them now, as the important thing to consider is whether a 30-hour week would be for the best interest of not only the men themselves, but the public or country in general.

Jan 1, 1920

September 20, 1917. As this meeting terminates the year's agreement under which the Engineering Foundation has appropriated its income to the National Research Council, a brief summary of what has been accomplished seems called for. The Research Council was organized Sept. 19, 1916. The Executive Committee was appointed at that meeting; since that date two other meetings of the Council have been held, one in Boston, on Nov. 13 and 14, the other in Washington on April 19. During the intervals between the meetings of the Research Council, the Executive Committee has conducted all of the business of the Council. There have been 29 meetings of the Executive Committee, 13 in New York up to the first of May, 15 in Washington subsequently, and one in Boston. The meetings in New York were devoted to the organization of the Research Council and especially to appointment of committees. At the outset, the Council had no very clear idea of the way in which it was to organize; there were several other groups of scientific men at work, among them, the Research Committee of the American Association for the Advancement of Science and the Engineering Committee of the Advisory Commission to the Council of National Defense. Time was spent in straightening out these two principal complications, both of which were satisfactorily adjusted. The upshot of these negotiations is to leave the Research Council as the only representative, national body of research men, assisting the Government. During the period up to May, the Executive Committee in New York selected carefully the personnel of some 25 principal committees, and of a large number of sub-committees; so carefully were these chosen that of the entire number, several hundred, there have been only one or two declinations. Some of the important steps in the development of the Research Council are the establishment of the Military Section, composed. of the members of the Council connected with the Government and resident in Washington. This Section put the Research Council into close contact with the most important officials of the Army and Navy. From it has grown the Washington office of the Council, and the recognition of the Research Council as the "Department of Science and Research of the Council of National Defense; " and the establishment of the Washington office after the Council of National Defense had officially recognized the Research Council. About this time Dr. Hale, Chairman of the Council, appointed Dr. Millikan to be Vice-Chairman to represent the Council in Washington, and Dr. Millikan has since then been in charge of the work of the Council. At the request of the Secretary, Dr. Millikan has prepared a brief report of some of the work of the Research Council during its first year, which is appended to this report. It shows that the Research Council has been active in much of the important work. under way in our preparations for war, and that it has rendered effective services to the Government.

Jan 12, 1917

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

By E. Robert Ruhlman

The term potash refers to potassium oxide (K2O), a compound not found in nature or produced by man but used as a basis for comparison of all potassium compounds and now is applied generally to various compounds of potassium used by agriculture and industry. Potassium, the last of the three major plant foods to be used in appreciable quantities by agriculture, was originally produced only from organic materials for chemical uses. The first recorded identification of a mineral source of potassium was in 1797; but, until the discovery in 1839 of the large deposits of soluble potassium salts in Germany and their development in 1860-61, nearly all potassium compounds continued to come from organic sources. With the importance of potash to plant life discovered in 1840 by von Liebig and the production of potash in Germany after 1861, agriculture soon became the major consumer of potash. In 1958 agriculture accounted for about 95 pct of the total potash consumption; the chemical industry used the remaining 5 pct. Mineralogy and Geology Potassium, an important constituent of the earth's crust, occurs in many forms in numerous rocks and minerals, including water solutions, but is not found in its native state. Twenty-five of the more important potash minerals are listed in Table 1. The properties of the five potash minerals most common in Permian salt formations follow: Sylvite is isometric; has a hardness of 2, a specific gravity of 1.98, vitreous luster, and cubic cleavage; and ranges in color from clear to brick red. In taste it is similar to halite but has a sharper taste and a cooling effect on the tongue. It is very plastic under pressure. Langbeinite is isometric; has a hardness of 4, a specific gravity of 2.82, vitreous luster, conchoidal fracture, and no cleavage; and ranges in color from clear to gray. It is taste- [ ] less, somewhat granular, and slowly soluble in water. Polyhalite is triclinic; has a hardness of 3, a specific gravity of 2.77, and dull luster; and

Jan 1, 1960

By N. A. Gokcen, John Chipman

D. C. Hilty (Union Carbide and Carbon Research Laboratories, Niagara Falls, N. Y.)—This paper is a very nicely detailed analysis of a difficult problem. I would like to point out that the results that Mr. Crafts and I published a few years ago had no reference to activity, or anything else of a similar nature; our results were strictly empirical. It is quite gratifying that we now have a case where results involving activity coefficients and results derived from direct observations on actual steel melts are practically identical. When two different laboratories, working from two entirely different approaches, come out with results in such good agreement in their major significance, that is an achievement. It is something that was not possible 15 or 20 years ago. There is one question I would like to ask Dr. Chip-man. It has to do with a very minor point of disagreement in these results. When we reported the kink in the Si-O solubility curve I think you may recall that it came at the different temperature levels at about the order of 0.015 to 0.03 pct 0 and 0.03 to 0.07 pct Si—we also pointed out that we had difficulty in obtaining data at that level, although we finally did get some. I note in going through the data for the present paper, that there are no samples in those particular silicon and oxygen ranges. I wonder if that was purely accidental or was there a reason for it. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—Mr. Hilty, do you have any explanation for that discrepancy between Dr. Chipman's curve and your own Mr. Hilty—Our explanation for it at that time was that for some reason our system probably was not in true equilibrium with SiO, that is, in equilibrium with the silica crucible at that level. We did observe, however, that that was the level at which both the metal and the slag became saturated with SiO,. On the average, in studying inclusion formation in small ingots permitted to solidify normally from the molten state, we observed pure silica inclusions at silicon contents over about 0.05 pct and FeO type inclusions at silicon

Jan 1, 1953

THE CHAIRMAN ( F. K. COPELAND, * Chicago, ,Ill.).-This is an interest-ing and very troublesome proposition to all of us. Ten or fifteen years ago, when the old-fashioned idea prevailed that a man was responsible for his own health and safety, that if anything happened to him it was his own lookout; we got along without this problem; but with the advent of accident compensation, with the agitation that there is all the time for pensions, sick benefits, and the responsibility of a company for the health of its employees, whenever you take a man on, that phase is becoming more and more important. One cannot afford to hire a man who is blind in one eye, even though he may have perfect sight in the other eye; if he loses that one eye, if lie becomes a total disability, the company is liable for the man's complete sight. Another thing that should make us particularly interested in this problem is the fact that the unions are very much opposed to it. One of the requirements of this steel unpleasantness is that the companies abandon their physical examination of employees. It is a very difficult problem to examine 400 or 500 men as intelligently as possible and decide whether a man on this or that side of the line is accepted. T. T. READ, Washington, D. C.-The United States. Bureau of Mines has in progress at the present time a study of the effect of underground atmospheric conditions on the safety and health of the workers. Im-proved methods have been employed and it is an excellent and ex-tremely valuable piece of research work.

Jan 12, 1919

By Harold Margalin, Elmars Ence

M. H. Mueller, M. V. Nevitt, and H. W. Knott (Argonne National Laboratory)—We have reported1 the crystal structure of Ti2CU as body centered tetragonal with a. = 2.944A and co = 10.786A, six atoms per unit cell, and space groupl4/mmm(MoSi2 type). This cell is larger but definitely related to the unit cell reported by the authors. It permits definite positions for the titanium and copper atoms in the cell located as follows: 2 Cu (a) 0 0 0; 1/2 1/2 1/2 4 Ti (e) 0 0 z; 1/2 1/2 1/2 + z; 0 0z; 1/2 1/2 1/2- z where z = 0.341 The face centered tetragonal cell reported by the authors can be transformed to a small body centered tetragonal cell with flo (small bet) = ao(fct)v2 Both unit cells have the same CO. Neither the face centered tetragonal cell with four atoms per unit cell nor the small body centered tetragonal cell with its two atoms per unit cell lend themselves conveniently to an orderly arrangment of the 2 to 1 ratio of titanium to copper atoms. When the co of this small body centered cell is tripled, however, a large body centered tetragonal cell results with six atoms per unit cell as described above. We had also noted that the X-ray patterns of Ti2Cu indicated that the structure could be approximately described by the face centered tetragonal cell as reported by the authors; how- ever, there was evidence for a few additional very weak lines whose positions indicated a larger unit cell. Since the X-ray scattering amplitudes of titanium and copper are nearly equal, it is evident that it is difficult to distinguish their positions especially from X-ray powder patterns. It was therefore decided to look at a powder pattern obtained by neutron diffraction since the scattering amplitudes of the two elements are considerably different in magnitude and opposite in sign. The sample used for neutron diffraction was selected from a group of three alloys prepared by arc melting using crystal bar titanium of 99.92 pet nominal purity and 99.999 pet pure Cu. The alloys designated as A, B, and C had the following respective compositions: Ti-32.8 at. pet Cu, Ti-33.3 at. pet Cu, and Ti-33.8 at. pet Cu. On the basis of the melting losses incurred, it was established that the actual concentration of either component in any of the alloys probably did not deviate from the intended value by as much as 0.1 at. pet. The alloys were annealed for 5 days at 700°C in evacuated Vycor capsules and quenched in tap water. The metallographic structures of these alloys are shown in Fig. 1. None of the alloys contained sufficient second phase to permit its positive identification. Since alloy B contained the least amount of second phase and since its composition placed it closest to the ideal stoichiometry, it was chosen for the neutron diffraction study. The oxygen content of alloy B was found by chemical analysis to be 0.06 at. pet. This particular intermetallic compound is especially suitable for investigation with neutron diffraction since if the titanium and copper atoms have a random statistical distribution, a near null-matrix would result in which there would be practically no coherent scattering of neutrons, and hence no Bragg diffraction peaks. Such a condition could come

Jan 1, 1962

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969