Search Documents

By R. A. Stauffer

THE chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll's and Dr. Schlecten's recent paper' has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000°C in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating to about 1000°C in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. THE REPLACEMENT OF Li20 IN SPODUMENE A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide present in the ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh. Analysis of the spodumene was as follows: [ ] Lime (cp -200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000°C in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1947

By Alan Bauer

DRILLING CONSIDERATIONS In considering blasting it is necessary to consider the drilling and explosives since one is generally concerned with the total cost of muck of a certain size in the pit or through the crusher. To get a current idea of the drilling situation in open pit mines plotted in Fig. 1 are the drilling costs per ton of material vs. hole diameter for rotary drill holes in large limestone, iron ore and taconite operations. The exception is the 2-in. diam hole which was drilled with a percussion drill in limestone. Each curve in Fig. 1 represents a different operation and the data cover many months of production drilling. The costs are total operating and maintenance and do not include machine depreciation. As the hole size is increased so are the machine size and the investment. Providing the tonnage is available to be drilled, then as the machine size goes up so does the productivity-markedly-and this same shape of curve applies. In some instances it is even steeper. The interesting thing to note is that in each case studied there is a substantial drop-off in cost/ton as the hole size is increased. This is true for the softest material considered, limestone, through to the hardest, taconite. How has this come about? In going from 10-in. to 123-in. diam holes, the powder factors have generally stayed about the same and the same type of muck has been produced. To date this has been mainly in the softer materials but it has also been steadily taking hold in the harder ones. On this basis, then, patterns are generally expanded as the ratio of the hole diameters or close to it, if the explosive type is kept the same. In the harder rocks the cost per foot of hole has increased somewhat so that the overall reduction in drilling cost per ton is about 25 pct. In somewhat weaker rocks of about 25,000 psi compressional strength the drilling cost per

Jan 1, 1968

By Patrick M. Hurley

The relationships between mineral deposits and various plate margin mechanisms are examined under the constraints of radiogenic isotopes and other geochemical indicators. It seems like1 y that: (1) deposits of the spreading ridge association are fairly ubiquitious through most of geologic history and can be recognized by the lithologic assemblage and primitive lead isotope ratios; (2) most metals in the island arc association are not derived entirely from a subducting oceanic plate, and have a partly continental affinity; (3) subduction beneath a continental plate generates ores which are derived either from the downgoing plate or from the lower crust; (4) the heating of a continental plate by thickening or by mantle plumes may develop a metallogenic province involving extraction of metals from the curst; (5) rifts and grabens developing thick sections of marine sediments with evaporites may be the locus of base metal mineralization by movement of reducing brine solutions resulting from diagenesis and bacterial reduction of sulfates

Jan 1, 1978

By William H. Radford

Having worked some rather lorn--grade gravel during the past season at a small profit, I give the actual figures, in the hope that other mining engineers interested in this line of work may be thereby induced to do the same, in order that we may all get more data on this little-ventilated subject. The property here referred to is situated in one of the northern counties of California, where hydraulic mining is still permitted by the courts. The water-right belonging to the mine is a good one, furnishing water during about nine months, whenever there is an average rain-fall, and a fair proportion of the precipitation is in the form of snow. The ditch, about 11 miles in length, is cared for during the rainy months by two men, and during the rest of the year by one; and the water cost last season, delivered at the mine, 0.69 cent per miners' inch. The season commenced in November, 1899, and ended the last of July, 1900. During this time, 655,657 miners' inches (an inch equals 1728 cu. ft. in 24 hours) of water were used for piping, and for sweeping the bed-rock at the end of the season. From actual surveys, this amount of water washed down 1,251,399 cu. yds. of material, consisting of pay-gravel lying on the bed-rock, and varying in thickness from a few inches to 8 ft., and practically barren top-material, consisting of mountain slide, carrying considerable broken rock, clay, and soil. The banks varied in height from 50 to 130 ft., the average height being 63 ft. The grade of the sluices was 7 in. to 12 ft., the boxes being paved with block-riffles 12 in. deep. Long bed-rock cuts extended from the heads of the sluices to within a few feet of the banks, and were kept practically to grade as the work advanced. At first, electric drills were used on this work; hut as it was found that heavy blasting shattered the rock too much, and caused slips, these drills were

Jan 1, 1902

By Frank Firmstone

IN the early decades of the past century the method of starting iron blast-furnaces by "scaffolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important "Reminiscences" printed by the late Samuel Thomas. I It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.' On the Continent it was still followed in the 60's,3 and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom '4 scaffolding" was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country:

Mar 1, 1907

By P. Pietrokowsky

lntermediate phases in the binary metal alloy systems Ti-Zn, Ti-Hg, Zr-Zn, Zr-Cd, and Zr-Hg have been investigated by X-ray powder diffraction methods. Gamma-TiBHg and Zr3Hg have a beta tungsten structure; TiHg and ZrHg are analogous to ordered AuCu (L l0 type); delta-TixHg and ZrHg, are isomorphous with ordered AuCu,, (L l2 type); ZrZnz is face-centered cubic (C 15 type); TiZna crystallizes in a C 14 type structure; and Zrll-, occurs in cubic and tetragonal modifications in which a random distribution of atoms exists. Additional information for the intermediate phase TiZn, is presented. THE physical metallurgy of titanium and zir-conium when alloyed with elements in subgroup 11-B of the periodic table has received comparatively little attention in the literature. Laves and Wallbaum' reported the existence of several intermediate phases in the system Ti-Zn. They identified TiZn as a CsCl (B 2) structure and described TiZn, as an ordered Cu,Au (L 1, type) crystal structure. Gebhardt' investigated very limited zinc-rich regions in the systems Ti-Zn and Zr-Zn. Phase relationships in these partial constitution diagrams were deduced from the results of thermal analysis and metallography, X-ray results being inconclusive. The first zinc-rich intermediate phase in either system was not identified. More recently, Anderson, Boyle, and Ramsey" have had occasion to refer to a partial Ti-Zn phase diagram (unpublished data) covering the region 0 to 10 atomic pct Ti, wherein two intermediate phases corresponding approximately to TiZn,, and TiZn,, were indicated. The metals used in this investigation and typical analyses as determined by the suppliers are given in Table I. The iodide-process zirconium which was used was not hafnium free. Experimental Methods Alloy Preparation: The relative ease with which titanium and zirconium combine with other elements places extensive restrictions on the methods by which alloying can be achieved. The direct current electric arc melting procedure was found to be unsatisfactory for preparing these binary alloys and for this reason solid state diffusion methods were utilized. The iodide process titanium and zirconium rods were filed by hand. Fines were subjected to a magnetic separation and classified as to size as either finer than 200 mesh or coarser than 200 but finer than 80 mesh. Powder mixtures of various binary combinations of titanium and zirconium with zinc and cadmium were compacted in a 12 mm diameter die and then placed in Vycor or quartz vials which were evacuated and sealed. The mercury alloys were prepared in a similar manner; the proper weight of liquid mercury being placed in a vial with minus 200 mesh titanium or zirconium. These ampoules were then heat treated at various temperatures and times depending on the characteristics of the particular alloy system. Upon completion of the heat treatment the ampoules were cooled rapidly and the specimens weighed. The loss in weight varied from 1 to 3 pct (except as noted in the text) and for this reason the calculated compositions were accepted as a fair measure of the actual alloy compositions. X-Ray Dif raction Techniques: Powder diffraction experiments were conducted at room temperature with a 143.2 mm Debye-Scherrer X-ray camera in which the film was placed in the Straumanis arrangement. When copper radiation was used, a nickel filter was employed, and for the cobalt target a filter of iron oxide was used. In both cases, the /i? filter was placed between the X-ray target and the powder specimen which was mounted on a glass fiber. The lack of information based on optical metallography placed reliance on the results obtained from the X-ray experiments for determination of

Jan 1, 1955

By J. H. Henderson, L. A. Wilson, R. L. Gergins, R. J. Wygal, D. W. Reed

This paper presents a method of predicting the production history of an underground combustion recovery process. A rigorous solution of the thermodynamics and hydrodynamics involved is beyond the scope of this report. However, a practical scheme to appraise combustion recovery performance has been Worked out. By prudent assumptions, regarding the attainment of steady-state conditions, a trial-and-error solution, which satisfies both material balance and three-phase relative permeability requirements has been evolved and tested. As a combustion zone moves through a formation the interstitial water, the water of combustion and a portion of the oil wil1 be vaporized. These vapors will move downstream to a cooler region of the formation where they will condense. Part of the remaining oil will be displaced by the imposed gas drive and what remains behind will be consumed as fuel. The fluids will distribute themselves downstrean? in a manner which will satisfy the three-phase relative permeability characteristics of the formation. Three distinct zones will exist ahead of the combustion zone: (I) a zone termed a water bank which contains three mobile phases, oil, water and gas; (2) a region containing two mobile phases, oil and gas, called the oil bank; and (3) a zone having the fluid saturution distribution which existed prior to combustion. The mobile water will impose a water flood on the oil in the region containing three flowing phases. The process can be visualized as a simultaneous water .flood and combustion-supported gas drive. It is possible to estimate the saturation distributions in the water bank and oil bank as well as the production history for any combustion temperuture if the porosity, three-phase relative permeability characteristics, oil viscosity and initial saturations are known. This has been done for injection pressures ranging from I to 100 atm, oil viscosities of 10 to 1,000 cp and porosities from 20 to 40 per cent. Several of these calculations have been checked in the laboratory, with the result indicating rather good agreement between the predicted and observed production histories. The analytical and experimental techniques are described and the comparison of predicted and observed performance presented. INTRODUCTION Considerable research by the oil industry during the past 10 years has been directed toward the thermal recovery of crude oil. Of all schemes considered, the one receiving the most attention is in situ combustion. This is a process in which part of the oil is actually burned within the reservoir rock. The uniqueness of the process lies in its potential. Theoretically, this potential generates from the following: (1) it may open the door to vast reserves previously not economically producible, (2) it may induce increased production rates where low rates are now realized and (3) it may give high over-all recovery efficiency. The general idea of the process has received considerable attention in the literature '-' and the following brief description is intended for orientation only. In situ combustion can be visualized by considering a linear system, one end of which represents the injection well and the other the producing well. The formation at the inlet end is raised to ignition temperature by placing a gas or electric heater at the face of the formation or by the ignition of thermite, charcoal or similar material. While heating, the water and part of the oil in the heated region is vaporized and moved out into the reservoir by the injection of gas containing oxygen. In addition, part of the oil is displaced as liquid by the imposed gas drive. The oil not displaced is modified to an immobile, coke-like material (hereafter referred to as coke) by the high temperatures existing immediately ahead of the combustion zone. This coke is used as fuel, and the combustion front advances through the formation at a temperature which is probably in excess of 800°F. As the combustion front advancek it will drive ahead all interstitial oil not rendered immobile and all interstitial water plus the water formed by the combustion of hydrogen. As a result the sand behind the combustion zone is freed of all oil and water. Although the general description of the process has been outlined in the literature, there has been no consideration of the behavior of the fluids moving downstream from the combustion front. It is the purpose of this paper to present a technique

By AIME AIME

NATURE was in a smiling mood on December 18, 1883. On that day, Chester Alan Fulton, the sixty-first President of the American Institute of Mining and Metallurgical Engineers, was born, and she endowed him with every good quality within her reach - looks, physique, intelligence, and character. Brought up in the valley of the Hudson River, with the mighty Palisades which make it the "Rhine of America," he has lived up to his early promise - as a man, as an engineer and as a friend.

Jan 1, 1943

By R. V. Ramani, George W. Luxbacher

Computer simulation of mine ventilation systems, after a slow start in the early sixties, is gaining increasing acceptance for planning, design, and evaluation purposes. Numerous programs are readily available from government, university, consulting, and industry sources. The computer adage "garbage in, garbage out" is as applicable in ventilation engineering as in any other application of computers, and has been responsible for the questionable results obtained in some instances. The source of input data for a ventilation simulation is most often a pressure-quantity survey of the mine, or, in the case of a new mine, information derived from a survey of an existing mine which has conditions similar to those expected in the new mine. The crucial step is to generate simulation input data from the ventilation survey. Problems such as quantities that do not balance, pressure gradients opposite to measured air flow, differences in the pressure datum in a multi-shaft mine, modeling of leakage, and deviations in flow from the square law (H=RQ2) are frequently encountered and must be resolved. The purpose of this paper is to discuss these aspects and to propose procedures which can lead to input data for valid simulations of mine ventilation systems.

Jan 1, 1982

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion—surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program's success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for example, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data. Of the many possible sources of contamination, probably most important are smelter fumes, which may distribute large quantities of metal contaminants over many square miles of ground. For several reasons, the investigation reported here was begun in the Coeur d'Alene district in northern Idaho: 1) a lead smelter has been operated in this district since 1917 and an electrolytic zinc plant since 1928, and presumably the contamination patterns are strongly developed; 2) to evaluate the usefulness of certain geochemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and other veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; 3) one of the economically important parts of the district lies south of the South Fork of Coeur d'Alene River and within a radius of five miles of the reduction plants near Smelterville (Fig. 1). In this area, and in the entire district, conventional methods of prospecting are hindered by heavy vegetation and thick soil cover, and the possibility of contamination by smelter fumes has discouraged geochemical prospecting. Should data reveal that geochemical prospecting could be done successfully in such an area, a particularly useful tool would be available to mining companies and prospectors searching for concealed orebodies in this economically important part of the district. The field work on which this report is based was done from July 28 to 31, 1955. It should be emphasized that this was reconnaissance study only, and therefore far from exhaustive. Previous Investigations in U. S. : The first geochemical survey known to have been affected by contamination was conducted in 1940—a geobotan-ical reconnaissance made in the Michigan copper district by a private company. Geologists found striking variations in the copper content of oak and maple leaves, but unfortunately the high copper isograds of the study seemed to be related more to the Calumet and Hecla copper smelter fall-out than to mineralized ground.' The leaves of one oak tree near the smelter contained 0.4 pct Cu. Similar contamination was reported by Clarke (Ref. 2, p. 41), who conducted experimental geochemical soil and botanical surveys at Ray, Ariz. He found that the leaves of oak trees growing in unmineralized ground near Superior, Ariz., contained more copper than the leaves of oak trees growing on the capping of the Ray orebody and attributed this fact to contamination from the fumes of the Magma smelter at Superior. According to H. E. Hawkes,3 soils and stream sediments in the Superior area are also severely contaminated. Hawkes' work there has shown a copper content averaging 0.5 pct in the surface horizons of soils within one mile of the smelter stack. Samples taken only a few inches below the anomalous surface samples showed only background copper values. In 1950 L. C. Huff' of the USGS made a geochemical survey in an area near Jerome, Ariz., and found considerable zinc and copper in the soils over unmineralized basalt close to Clarkedale, Ariz., and over limestone close to Jerome. As the amounts were notably greater than could reasonably be expected to be derived from the underlying rocks, Huff suspected airborne contamination from the smelter at Clarkedale. Description of Area: The area sampled in detail (Fig. 1) for the study presented here is one of strong relief. The dominant watercourse is the westward-flowing South Fork of the Coeur d'Alene River. East of Kellogg the South Fork flows in a rather narrow canyon, but its valley floor widens considerably to the west where much of the flood plain is covered by an extensive veneer of mining, milling, and smelting debris. South of the South Fork and between Big Creek and Pine Creek is a mountainous area where

Jan 1, 1960

By F. G. Miller

The washabilities of typical bituminous coals are discussed in an effort to illustrate the importance of determining, by a complete washability study, the sulfur forms and their distribution in a coal. This study will then show the extent to which the sulfur can be removed. It should be emphasized that each potential application requires a thorough study because of the varying amounts of sulfur in different coals. It is not the intent of this paper to show the best results that flotation can produce, but rather to illustrate the potential of this process and point out the importance of improved flotation techniques where sulfur reduction is involved. It is generally accepted that sulfur exists in coal in three forms: (1) pyritic, (2) organic, and (3) sulfate sulfur. Sulfate sulfur usually makes up less than 1% of the total sulfur content. Pyritic and organic sulfur make up almost all of the total sulfur content, occur in varying amounts in different coals, and can vary greatly in coal of the same seam. Pyritic sulfurs of 20% to 80% of the total sulfur have been reported. Other authors have shown that it is not possible to remove the organic sulfur without chemically altering the coal. Chapman and ones' state: "Organic sulfur, unlike pyritic sulfur does not exist as discrete particles, but is intimately associated with the coal structure, and as such it is not possible to remove it or reduce its concentration by physical means." Any success in removing sulfur has come about by removing pyritic sulfur by physical means; therefore, removal of sulfur in the pyritic form is the subject of this investigation. The extent to which any impurities can be removed from a particular coal can be determined by a washability study. Outside of crushing coal to finer sizes or chemically altering the coal, there are no known methods of changing this inherent washability characteristic. The efficiency of various methods used to remove impurities can be determined by comparison of results produced at a yield to the results as shown by a washability study. In recent years heavy media processes have proven their ability to wash plus 28 mesh coal and nearly produce results shown to be theoretically possible by the washability study. Therefore, it is the objective of this paper to show various methods of treating the finer fractions of the coal, in the hope of developing

Jan 1, 1964

By Horace Pops

Martensitic transformation has been studied during cooling and heating in ß-phase Cu-Zn alloys to which small additions have been made of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, and Sb. The start and finish of the martensitic reaction and the variation of transformation temperature with third-element content were determined by electrical-resistivity measurements from alloys which had either constant zinc contents or constant values of electron concentration. All of the third elements, except nickel, lowered the transformation temperature if the results were plotted along the lines of constant zinc contents in each ternary system. A significant difference in the rate of lowering of the transformation temperature per atomic percent of the third element was observed for elements which had the same nominal valence. No systematic variation of transformation temperature with the valence of the third element was observed. It is suggested that the observed increase in transformation temperature for nickel-bearing alloys is due to the transfer of electrons from the conduction band of the alloy to virtual bound states. However, electron concentration is not the most important factor controlling the instability of the 0 phase. The transformation temperatures of the ternary alloys can be predicted from the following approxilnate expression: Ms (°K) = +3280 - 80 Zn + 8 Ni - 30 Ag - 12 Au - 140 Cd -90 Ga- 145 In - 80 Ge -175 Sn - 120 Si - 150 Sb MOST binary ß -phase alloys based upon the noble metals copper, silver, and gold are unstable at low temperatures and transform spontaneously by a martensitic reaction. This transformation has been studied recently in the ordered bcc ß'-phase Cu-Zn binary al1oys1,2 where the transformation temperature is below the room temperature and decreases with an increase in zinc content. It has been reported that the transformation temperatures can be raised above room temperature by small additions of a third element such as silicon3,5 or gallium,4,5 but no quantitative study has been made. The transformation temperature of different binary alloys can be altered by third-element additions. For example, it was shown that nickel and copper may have a large effect on the Ms temperature of CU-Al6 and Au-cd7 alloys. The present investigation was made to determine systematically the influence of various third elements on the martensite-transformation temperature of Cu-Zn ß-phase alloys. Since these alloys have an electronic origin,' alloy compositions were chosen so that the transformation temperatures could be determined at constant zinc contents or at constant values of electron concentration. I) EXPERIMENTAL PROCEDURE Ten ternary alloy systems were obtained by adding nickel, the noble metals silver and gold, and some B-subgroup elements to a Cu-Zn matrix. These are arranged according to their rows and columns in the Period Table as follows: Each ternary alloy was prepared by melting and casting weighed quantities of high-purity metals (99.99+ pct) in sealed quartz tubes under a partial pressure of helium to make a 4-g ingot. The molten alloys were shaken vigorously and then quenched in water. Since the weight loss was negligible, the compositions of the ingots after casting and annealing were assumed to be the same as the nominal compositions. The ingots were homogenized after casting in helium-filled Vycor tubes for 24 hr at temperatures between 750" and 810 C and quenched into brine. Metallographic examination revealed that all alloys were homogeneous, poly crystalline ß-phase alloys, and that the grain size was in the range 1 to 5 mm. Electrical-resistivity measurements were made to determine transformation temperatures of the ternary alloys during continuous cooling or heating. Transformation temperatures of the ternary alloys can be determined by electrical-resistivity measurements since the resistance of the martensitic phase is much higher than that of the 0' phase. The technique has been described previously in connection with a study of Au-Zn alloys.9 The reproducibility of transformation temperature was approximately ±6°C. II)RESULTS A hysteresis was always observed in electrical-resistivity curves and was usually less than about 12°C.

Jan 1, 1967

By J. D. Wheeler, H. W. Mathews

The increased activity in West Texas, which started in 1933, has continued through 1936 at a constantly accelerated rate. During 1936 there were 1442 wells completed in the area as compared with 700 in 1935 and 468 in 1934. Of these completions, 1313 were producers with a total 24-hr. potential in excess of 1,750,000 bbl. From among the 1442 wells, eight are considered to be discovery wells for new West Texas fields. New Fields Bennett.—The Bennett field, which added Yoakum County to the oil-producing counties of West Texas, was actually indicated as an oil-producing area during 1935, but the discovery well, Honolulu Oil Corporation, Ltd. and Cascade Petroleum Company's Bennett No. l, was not given a production test until April 1936. The discovery well made 15 bbl. per hour through 3/4-in. choke with a plugged-back total depth of 5264 ft. First oil in the hole was from 5088 to 5090 ft., which is several hundred feet below the top of Permian lime. Producing limits of the field are unknown, as the second test had not reached the pay at the close of the year. Henderson.—-To date indications are that the Henderson pool, in northern Winkler County, is the most prolific area opened during 1936. This field, which lies to the north of the old Hendrick pool, is producing from the same reef-type dolomitic lime producing in the older field. The Henderson field was opened by the completion of R. H. Henderson, J. B. Walton-Humble 1-A in April 1936 for a natural flow of 2306 bbl. per day through tubing. Total depth of the discovery well is 3049 ft. Later development has indicated the productive area to be a rather narrow zone running slightly west of north. Present area of from 1000 to 1500 acres has been proved for production. Keys and Emperor.—The Keys and Emperor pools in the belt of sand pools running across Winkler County appeared for the first time on State proration schedules during 1936. This report considers these pools as links in joining the belt of sand production across Winkler County, for

Jan 1, 1937

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

UNDER the same justification that I spoke to you in the preceding chapter on crystal and some other gems, I can now speak much better and with much greater reason of glass, since it is one of the effects and peculiar fruits of the art of fire. Every product that is found [41v] in the interior of the earth is either stone or metal or one of the semiminerals, and glass, as is seen, resembles them all, although in all respects it is dependent upon art. Therefore it seems to me that before coming to the discussion of the arts themselves, I must treat of this very beautiful composition created by art and number it with the semiminerals. Thus in this chapter I shall speak to you of glass, not as a proper semimineral, nor yet as a metal, but as a fusible material that is almost made mineral by art and by the power and virtue of fire, born from the speculation of good alchemistic savants, through whose efforts it imitates. the metals on one hand and the transparency and splendor of gems. on the other. Certainly it is a very beautiful thing and one that should not be left buried in silence, in consideration first of how great a thing art has been, able to discover, and then because its beauty makes it such a pleasing thing for making drinking. glasses and an infinite number of other ornamental things that satisfy the desires of man. I shall begin, then, by telling you, to the credit of the alchemists, how I believe that this thing was found through their desire to make gems; for when they could not bring them to perfection (as also happened with the metals) they made this beautiful and attractive product, glass. However, Pliny says that it was found by chance in Syria at the mouth of the Belus River by certain merchants who were driven there by the fortunes of the sea and forced to stop and disembark there for a time in order to eat. In cooking the food they saw the rocks of that place converted into a flowing, lustrous material. And as they thought about this, it seemed beautiful to them, and when they went away they carried some stones and plants with them. Thus they gave beginning to glass making. But now leaving this discussion it does not matter how it may have been discovered, whether by merchants or by ingenious alchemists. Art is that which has given it being, through many experiments and by addition

Jan 1, 1942

By F. L. Ransome

The dike here described is exposed in the workings of the Wedge and Bachelor mines, on the southern side of Red Canon, north of the town of Ouray, Colorado. Its course is north 80° east, or nearly east and west, and it hades to the north about 10°. It rarely outcrops, and was nowhere seen at the surface near the mines. A specimen collected by Dr. A. C. Spencer about two miles to the westward, near the mouth of Red Creek, indicates, however, a probable exposure of the dike near this point. The Wedge and Bachelor mines lie in a nearly horizontal series of fine-grained, light-grey sandstones, alternating with beds of very fine-grained shale of the same color. The shale as encountered underground is unusually compact and massive, but weathers readily on exposure, and splits much after the manner of ordinary shale. When fresh it closely resembles some finely arenaceous limestones, but it does not effervesce with acids, and is eseentially a fine, indurated, siliceous silt. Near the surface, and near the top of the sedimentary series as

Jan 1, 1901

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By AIME AIME

THE United Electric Coal Companies, operating large strip mines at various points in Illinois, pioneered in developing and perfecting the strip method of mining coal by use of large shovels and drag-lines. Coal stripping was first started on the properties owned by this company near Danville, Ill., in 1885. The first mechanical' excavating machine used for the purpose was really a dredge minus the hull, which had been purchased from the Marion Steam Shovel Co. It was erected on a wood frame supported by wheels and was referred to as a dry-land dredge or stripping machine. Wood was used throughout in the construction of this primitive excavator, even for the boom which was 50 ft. long. A single-cylinder vertical steam engine furnished power to hoist the %-yd. dipper arid swing the boom. 400 cu. yd. of overburden moved in a day was a great record.

Jan 1, 1936

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-'; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann's and Planck's constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By N. J. Grant, C. F. Flo, F. B. Cuff

An investigation of the Ti-Cr system has shown the presence of a complete series of solid solutions in the ß phase, with a minimum in the solid us near 50 pct Cr. An intermetallic compound, TiCr2, forms during cooling from the ß solid solution. There is a eutectoid reaction at the low chromium side of the system. IN view of the recognition of the potentialities of titanium and its alloys as important structural materials there has arisen a need for a systematic investigation of various titanium binary diagrams. Of these, the Ti-Cr system was of particular interest because of the improved properties imparted to titanium by small chromium additions. A literature survey disclosed a partial constitution diagram that had been suggested by Vogel and Wenderott,¹ This diagram, shown in Fig. 1, is the result of work done on the Fe-Cr-Ti ternary system. Alloys containing less than 43 pct Cr were not investigated. In addition to this, a study of alloys in the Ti-Cr system was reported by McPherson and Fontana.² Adenstedt3 furnished a number of dilato-meter curves obtained from specimens containing 5, 10, and 15 pct Cr. Very recently, McQuillan4 submitted a proposed diagram covering the complete range of compositions between titanium and chromium. This diagram was in general agreement with the one described here. Experimental Procedure Sponge titanium (99.7 pct) and electrolytic chromium (Bureau of Mines analysis: 99.03 pct Cr, 0.40 pct Fe, 0.53 pct O2) were used for the initial determination of the system. Subsequent refinement of points, particularly for the low chromium side of the diagram, was accomplished by using iodide titanium and high purity chromium (National Research Corp. analysis: 0.050 pct C, 0.045 pct O2). The Ti-Cr alloys were prepared by melting 25 g charges in an enclosed, water-cooled copper crucible using a movable tungsten electrode. The atmosphere was helium, prepurified by first passing it through a drying agent and then through sponge titanium heated to 850°C. Particular care was taken to avoid any large scale segregation resulting from insufficient mixing of the components. Each charge was melted and kept molten for approximately 1 min, allowed to cool, inverted, remelted, and kept molten for an additional minute. In order to ascertain the amount of impurity pickup (oxygen and nitrogen) during the melting procedure, three iodide titanium specimens were melted in sequence and then checked for increased hardness. The specimens in the as-cast condition showed a relatively large hardness increase over the hardness of the as-received iodide titanium. The scattering on these readings was large. However, after the specimens had been homogenized at 840 °C for 2 hr and slowly cooled, the measured increase in hardness over the as-received titanium was small with a corresponding decrease in scatter. The reason for this hardness change is that in heat treating these specimens below the transformation temperature (885°C) there was a conversion from the as-cast structure to the more nearly equilibrium structure of the annealed specimen. The alloys were analyzed for chromium content and although the actual percentage was invariably low the deviation from the nominal composition never exceeded 0.6 pct Cr.

Jan 1, 1953