Search Documents

By Charles A. Kumke

The ('slot" system of mining in use at the Golden Queen mine, Mojave, Calif., does not involve any new mining methods. It is, however, a new combination and adaptation of several stoping systems in common practice. The first plans for stoping operations at the Golden Queen mine called for ordinary shrinkage stopes. The hanging wall of the vein, where exposed, is a very hard felsite with a dip varying from 50° to 70°. The vein itself is quartz, shattered and fractured enough to make it easy to drill and blast to a clean hanging wall. There is no well defined footwall. The footwall limits had to be determined by assays as the metal content faded out into the felsite. Two shrinkage stopes, each approximately 200 ft. long, were laid out and started on the 200-ft. level. One of these stopes, varying in width from 8 to 18 ft., was carried on up to the top limits of the ore, approximately 120 ft., without a break in the operation. The shrinkage system proved entirely satisfactory and low costs resulted from this operation. In the final drawing of this stope, two timbermen followed down on the ore, scaling the hanging wall clean of small fragments and placing an occasional long stull from foot to hanging wall where it was deemed necessary. Few such stulls, however, were required. The hanging wall stood up very well until the stope was entirely emptied of ore. Waste fill was then put into the stope by the glory-hole method, through a waste raise that had previously been run to surface from the middle of the stope. The second shrinkage stope ran into difficulties about 35 ft. above the sill floor. Up to this point the maximum width of the ore had been about 15 ft. The ore suddenly widened into the footwall to a distance of 40 ft. in the north end of the stope. In extending the stoping operations over this, width, it was soon found that the vein material would not arch and support itself. Drilling in this end of the stope was then entirely too hazardous, and all operations were stopped. The ore was drawn through the chutes below as rapidly as possible and as soon as the stope was entirely

Jan 1, 1937

By Oliver Smalley

Except for the work of Guillet, who conducted a systematic investigation on the zinc-replacing value of nickel in brass, and extended his investigation with a view to developing commercial high zinc content nickel brasses, the author does not know of any other systematic research on the subject. The most promising commercial alloys and their physical properties obtained by Guillet are given below: These test results scarcely justify the use of such quantities of so expensive a metal, and could have been obtained from ordinary commercial brass. For purposes of comparison, the physical properties of ordinary brasses, ranging from 70 per cent. to 50.1 per cent. Cu in both the cast and normalized1 conditions are included in 'Table 1. These incidentally furnish a useful standard of the properties of castings and of rolled, extruded and forged brass when correctly annealed. A close study of some of the well-known special brasses containing nickel reveals a series of alloys which bewilder by their complexity, and me can only hazard a guess at the function and commercial value of each of the many elements used.

Jan 1, 1926

By P. W. Bennett, E. M. Elkin

A new technique for the recovery of palladium and platinum and sludge from go12 electrolyte eliminates many of the drawbacks of the zinc-dust cementation process. In the electrolytic refining of gold by the Wohwill method, the electrolyte contains about 100 gpl gold as AuCl, and 100 gpl free hydrochloric acid. Any palladium and platinum contained in impure gold dissolve and accumulate in the electrolyte. When their concentration approaches that of gold, it becomes desirable to discard the electrolyte and to recover the gold and the palladium and platinum. As practiced at Canadian Copper Refiners until recently, discarded electrolyte was treated with sulfur dioxide to precipitate the gold. 2AuCl3 + 6H2O + 3SO2 —2Au + 6HC1 + 3H2SO4 The gold precipitate was filtered off, washed with water, and melted with scrap anodes. The wash water was added to the gold-free filtrate and treated with zinc dust to cement the palladium and platinum. PdCl2 + Zn — Pd + ZnCl2 PtCl4 + 2Zn—Pt + 2ZnCl2 The precipitate was separated and sold as Pd-Pt concentrate, and the barren filtrate and wash water were discarded. The receipts of palladium and platinum at this company were too small to warrant their refining. The process suffered from a number of disadvantages. Handling the gold-free solution was disagreeable, as it was laden with sulfur dioxide even after blowing with air overnight. Subsequent treatment with zinc dust was also troublesome. A large excess of zinc dust was required. Spray, acid mist, and vigorous evolution of hydrogen accompanied the reaction. The Pd-Pt precipitate was grossly contaminated with occluded unreacted zinc and with yellow granules of sulfur, thought to be formed by the reduction of sulfur dioxide and its derivatives. Repeated boiling of the precipitate with hydrochloric acid and washing with water decreased somewhat, but did not eliminate, the zinc. After drying overnight, the precipitate hardened to a clinkerlike mass that was difficult to grind. Grinding, handling, and packing created heavy dusting. Even weighing in an analytical balance generated dust, indicating that the powder was easily charged with static electricity. The total palladium and platinum content of the powder varied from 56 to 72 pct, with an average of 65 pct. The powder dissolved in aqua regia with difficulty, leaving a small amount of insoluble residue. However, the main drawback of the process was the strongly hygroscopic Pd-Pt product. The powder showed a marked though erratic increase in weight and a corresponding decrease in assay on exposure to air, even during the course of laboratory analysis. Such changes were the source of disagreement between Canadian Copper Refiners and the buyers of concentrate. The cause of the change in weight is believed to be hydrogen, liberated by the action of zinc dust on hydrochloric acid. Some of this hydrogen was adsorbed so strongly by the precipitate that it could not be driven off during the drying. On exposure to air it oxidized catalytically, forming water. Experiments soon showed that the entire process of treatment of discarded electrolyte then in use would have to be changed. A small quantity of apparatus was moved into the gold room, and experimentation was held to a minimum compatible with the development of a new process. PALLADIUM AND PLATINUM PRECIPITATION It was thought that zinc could be replaced with a reagent other than a hydrogen-evolving metal. Semiquantitative experiments showed that platinum and palladium could be precipitated completely from the gold-free solutions with such well-known reagents as sodium formate, formic acid, formaldehyde, and paraformaldehyde. Sodium formate was the preferred reagent, since the other three are volatile and somewhat toxic. The gold-free solutions used were those saturated with sulfur dioxide, partly freed of sulfur dioxide by aerating overnight, completely freed by boiling, as well as strongly and weakly acidic, neutral, and alkaline solutions. The reactions are complex and can be represented by these over-all equations: PdC1, + HCOONa — Pd + NaCl + HC1 + Co2 PtCl4 + 2HCOONa — Pt + 2NaCl + 2HC1 + 2CCX, Strongly acidic solutions required as much as five times the theoretical amount of sodium formate as did solutions neutralized to pH 4.5. Increasing the pH decreased the consumption of

Jan 1, 1965

By Henry M. Howe

This paper gives the results of an investigation of the beha vior of the argentiferous cobalt-nickel arsenides of Temiskam-ing, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. Object of the Investigation. The object of the investigation was to learn: 1. The temperature at which the arsenic is most rapidly expelled ; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at. the beginning of the roast. II. Nature of the ORe. The important ores mined in the Temiskaming deposits are: native silver—with small amounts of dyscrasite (Ag,Sb), ar-gentite (Ag,S), pyrargyrite (Ag,SbS,)—smaltite (CoAs,), chlo-anthite (NiAs,) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent.; nickel, from 3 to 4.7 per cent.; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite. In our 1aboratory-work

Jan 1, 1908

By Charles Kumke

THE "slot" system of mining in use at the Golden Queen mine, Mojave, Calif., does not involve any new mining methods. It is, how-ever, a, new combination and adaptation of several stoping systems in common practice. The first plans for stoping operations at the Golden Queen mine called for ordinary shrinkage stopes. The hanging wall of the vein, where exposed, is a very hard felsite with a dip varying from 50° to 70°. The vein itself is quartz, shattered and fractured enough to make it easy to drill and blast to a clean hanging wall. There is no well defined footwall. The footwall limits had to be determined by assays as the metal content faded out into the felsite. Two shrinkage stopes, each approximately 200 ft. long, were laid out and started on the 200-ft. level. One of these stopes, varying in width from 8 to 18 ft., was carried on up to the top limits of the ore, approxi-mately 120 ft., without a break in the operation. The shrinkage system proved entirely satisfactory and low costs resulted from-this operation. In the final drawing of this stope, two timbermen followed down on the ore, scaling the hanging wall clean of small fragments and placing an occasional long stull from foot to hanging wall where it was deemed necessary. Few such stulls; however, were required. The hanging wall stood up very well until the stope was entirely emptied of ore. Waste fill was then put into the stope by the glory-hole method, through a waste raise that had previously been run to surface from the middle of the stope. The second shrinkage stope ran into difficulties about 35 ft. above the sill floor. Up to this point the maximum width of the ore had been about 15 ft. The ore suddenly widened into the footwall to a distance of 40 ft. in the north end of the stope. In extending the stoping operations over this width, it was soon found that the vein material would not arch and support itself. Drilling in this end of the stope was then entirely too hazardous, and all operations were stopped. The ore was drawn through the chutes below as rapidly as possible and as soon as the stope was entirely

Jan 1, 1937

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By Charles Pack

Die castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into three groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings. In the machine shown in Fig. 3, patented by Doehler in 1910, compressed air is used for forcing the metal into the die. In Fig. 4 is shown another of this type of machine. Here compressed air is applied to the surface of the molten metal to force it into the die. In a machine patented by Chandler in 1914, shown in Fig. 5, the

Jan 1, 1919

Bernard MacDonald, Guanajuato, Mexico (communication to the Secretary*):—Mr. Iceyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley.

Jan 1, 1909

By F. C. Newton

RefineRs of lead by the Parkes process have always been solicitous of recovering the zinc used in the desilverization, and justly so, as the loss in zinc constitutes one of the heavy costs in this method of refining. Part of this loss is due to the absorption of zinc by lead, and in the present state of knowledge is not recoverable as metallic zinc. The remainder of the zinc, which finds its way into the precious-metal-bearing crust, is recoverable and naturally engages the operators' most exacting attention. Careful elimination of the impurities in base bullion has enabled the refiner to produce a zinc crust better adapted to retorting, which reflects favorably in the zinc recovery;- and to produce a richer crust, thereby lowering the zineking cost, as the increased efficiency of the zinc results in less of it being in circulation. It is obvious that if the ratio of concentration be increased, a lessening of the amount of crust formed will ensue, throwing less work on the retorts and diminishing the amount of retort metal sent to the cupels, thus making an actual money saving in all these operations. In the effort to obtain a rich crust, the metallurgist has increased the heat to a considerable degree, upon the assumption that at the higher temperature the zinc-dver alloy could be squeezed free from the adhering lead. A further possibility for improvement suggested itself in the freezing-point curve of Prof. H. C. Carpenter, upon zinc and silver. Study of this curve disclosed the existence of a definite chemical compound, Zn3Ag2, with a freezing point of 665" C., a promising compound for practical application. In the experiment undertaken it was endeavored to force this compound into the crust, hoping thereby to obtain a higher concentration than formerly. It was recognized that in bringing a large kettle of lead to such a heat, more fuel would be used, the life of the kettle would perhaps be shorter, and other disadvantages would be experienced. AS a commercial operation, the project would have to stand on its own feet,

Jan 1, 1915

By W. H. Kantner

IN this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change sub-sidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the sur-face to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the east and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody-which is on the northwest side-is 600 ft. southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

Jan 1, 1904

By G. R. St. Pierre, A. J. Wilhelem

In connection with the reduction of hematite or magnetite to metallic iron, it appeared desirable to study the rate of reduction of each oxide to the next lower oxide under conditions which excluded all other condensed phases. For this purpose, pellets of Fe,O,, Fe,O,, and oFeOo were prepared. A gas train for the preparation of Ar-Hz-H20 mixtures was employed to establish a continuous flow of a controlled atmosphere over a pellet suspended on a balance. In this manner the following individual reduction steps could be studied: For example, pellets of hematite were reduced solely to magnetite by adjusting the gas atmosphere such that it was oxidizing to wustite. In other words, the reaction was complete when the hematite pellet had been totally converted to magnetite. The pellets were prepared from Baker Chemical ferric oxide. The ferric oxide powder was moistened and handrolled. Air sintering at 950°C produced Fe,0, pellets with a density of 3.65 g per cm3. The pellets ranged in size from 0.6 to 1.2 cm diam. The magnetite and

Jan 1, 1962

By H. P. Leighly, J. W. Marx, H. L. Walker

A relationship between recrystallized grain size and prior deformation is predicted from elementary statistical considerations, and reasonable agreement with experiment is obtained. RECRYSTALLIZATION phenomena have received much theoretical and experimental attention, and very adequate discussions of the various mechanisms suggested have been given by Anderson and Mehl,' Cook and Richards,' and Burgers," and others. It suffices to note here that the initial concepts fitted one of two general hypotheses: I—The new crystals are nucleated within microscopic regions at which there is a concentration of internal stress, i.e., volume elements of maximum strain energy. 2—The new crystals have their inception in volume elements of minimum strain energy. In a comprehensive early review of the subject, van Arkel' considered both possibilities and came to the conclusion that hypothesis 2 was inconsistent with the experimental fact that the number of nu-cleations increased with increasing deformation. He suggested that, if allowance was made for a preliminary atomic rearrangement at the points of large internal strain, hypothesfs 1 provided the more reasonable concept. Following the initial observations of Collins and Mathewsonb nd Crussard,Y he systematic X-ray investigations of Cahn' and Guinier and Tennevin" established the existence of a polygonized structure in metals that had been cold-worked, and subsequently annealed, under conditions such that re-crystallization did not occur. This new experimental evidence by no means disproved the first nucleation hypothesis, a fact recognized by both Beck" and Cahn,10 who independently suggested nucleation mechanisms based on the idea that regions of large strain might polygonize before the bulk of the less deformed material. These mechanisms, together with others recently proposed," are dependent upon the prior existence of some degree of polygonization in the deformed material. On the other hand, a critical examination of the published data leads to the supposition that polygonization may not be the necessary precursor of recrystallization, but merely its favored energetic competitor. In regions where the lattice distortion is not too severe, the limited adjustment afforded by polygonization may permit the lattice to drop to a relatively stable low energy state in which the nucleation of a new crystal becomes improbable, even at elevated temperatures. Such structures, of course, might provide a fertile field for the growth of nuclei, if these could be introduced. In regions of concentrated lattice distortion, polygonization alone may not be able to accomplish an adequate strain reduction, and in these volume elements sufficient thermal activity permits the more drastic atomic rearrangement involved in nucleation. Completely polygonized structures are known to withstand extended heating close to their melting points," with no other effect than a slow enlargement of some of the subgrains at the expense of others. Once started, macroscopic recrystallization might be expected to go to completion in a matter of minutes under similar heat treatment. Crussard12 and his coworkers have found that recrystallization may occur in single crystals of impure (about 99.7 pct) aluminum without any detectable prior polygonization. The indication here is that large Cottrell impurity atmospheres inhibit dislocation movement, thus suppressing polygonization to such an extent that the alternative process, recrystallization, dominates the lattice restoration. Experimental studies relating recrystallization directly to stored energy have not, at the present time,

Jan 1, 1954

By D. G. Westlake

Resistance was measured as a function of temperature, 77° to 350°K,for niobium with hydrogen concentrations up to 3.76 at. pct. Cooling curves exhibited a discontinuity in slope that was attributed to the initiation of hydride formation. A thermal hysteresis was explained in terms of diffusion and the effects of mechanical constraint on nucleation and growth. The heat of solution of hydrogen in saturated Nb-H solid solution was 2. 737 * 0.045 kcal per g-atom, including an unknown stress contribution. The critical ternperatures for hydride formation during cooling and for embrittlement are correlated but not coincident. This, too, has been explained in terms of mechanical constraint and stress-itlduced tratzsfomtation. Nb-H alloys undergo a ductile-brittle transition with decreasing temperature.'-3 Similar behavior has been noted for v-H.1,5 For the latter system, there is evi-dence6 suggesting coincidence of the temperature of minimum ductility and the critical temperature T, for initiation of metal hydride precipitation during cooling. A decrease in ductility due to the presence of brittle hydride particles is readily explainable. The fact that ductility begins to decrease at some temperature higher than T,4,5 has led us6 to suggest that precipitation may be strain-induced locally during tensile testing. Wood and Daniels' have reported that a plot of temperatures for 10 pct reduction in ductility vs hydrogen concentration in niobium is not coincident with, but parallels, the solvus.7,8 They believe this indicates a correlation of precipitation and embrittlement. Unfortunately, the two reported solvuses 7,8 to which Wood and Daniels refer are not in agreement with each other. Furthermore, neither solvus was determined experimentally: each was a plot of calculated solubilities. Thus. neither is highly dependable for determining whether embrittlement coincides with initiation of hydride precipitation. Longson 9 studied phase relations in the Nb-H system between 77° and 473°K by dilatometry. Comparison with metallographic observations convinced him that discontinuities in the slopes of his dilatometric plots were coincident with the initiation of hydride precipitation. Plotting the logarithm of the hydrogen concentration vs the reciprocal of the temperature at which precipitation was initiated during cooling, he obtained a straight line shown in Fig. 1. Walter and chandler,'' using X-ray techniques to detect the for mation of a second phase? have obtained three experimental points in the temperature range 295° to 338°K which fall within Longson's experimental error for this plot. A similar plotg of temperatures at which dissolution was completed during heating was a parallel line shifted toward higher temperatures. A straight-line plot was obtained, also, for the temperatures of the ductile-brittle transitions,9 but it was shifted toward still higher temperatures. Longson calculated an activation energy of 2.980 * 0.300 kcal per mole for the hydrogen embrittlement mechanism, compared with 3.180 * 0.400 kcal per mole for hydride formation. Despite this agreement, he concluded, "It seems unlikely that embrittlement results from hydride formation..." because hydrogen embrittlement was observed at temperatures above the solvus. It is our contention that embrittlement is correlated with precipitation of the hydride.6 Because only Longson has investigated Nb-H phase relations at sub-ambient temperatures, we deemed it advisable to re-determine the temperature dependence of the solubility using the resistometric technique already proven successful for the V-H system.6 Coincidence of our solvus with temperatures for embrittlement would

Jan 1, 1970

By Charles A. Kumke

THE "slot" system of mining in use at the Golden Queen mine, Mojave, Calif., does not involve any new mining methods. It is, however, a new combination and adaptation of several stoping systems in common practice. The first plans for stoping operations at the Golden Queen mine called for ordinary shrinkage stopes. The hanging wall of the vein, where exposed, is a very hard felsite with a dip varying from 50º to 70º. The vein itself is quartz, shattered and fractured enough to make it easy to drill and blast to a clean hanging wall. There is no well defined footwall. The footwall limits had to be determined by assays as the metal content faded out into the felsite. Two shrinkage stopes, each approximately 200 ft. long, were laid out and started on the 200-ft. level. One of these stopes, varying in width from 8 to 18 ft., was carried on up to the top limits of the ore, approximately 120 ft., without a break in the operation. The shrinkage system proved entirely satisfactory and low costs resulted from this operation. In the final drawing of this stope, two timbermen followed down on the ore, scaling the hanging wall clean of small fragments and placing an occasional long stull from foot to hanging wall where it was deemed necessary. Few such stulls, however, were required. The hanging wall stood up very well until the stope was entirely emptied of ore. Waste fill was then put into the stope by the glory-hole method, through a waste raise that had previously been run to surface from the middle of the stope. The second shrinkage stope ran into difficulties about 35 ft. above the sill floor. Up to this point the maximum width of the ore had been about 15 ft. The ore suddenly widened into the footwall to a distance of 40 ft. in the north end of the stope. In extending the stoping operations over this width, it was soon found that the vein material would not arch and support itself. Drilling in this end of the stope was then entirely too hazardous, and all operations were stopped. The ore was drawn through the chutes below as rapidly as possible and as soon as the stope was entirely

Jan 1, 1937

By Parviz Montazer, Robert King, William Ubbes, Gideon Chitombo

This paper describes the results of a detailed study that was undertaken to define the spatial distribution of permeability within a five meter thick envelope around the CSM/ONWI room. Detailed fracture orientations and distribution were determined through mapping of the walls of the opening, logging of oriented core, and visual examination of borehole walls with a borescope and a T.V. camera. Over 3,500 measurements were made from which the three dimensional distribution of fractures was determined. Two principally different testing equipment designs and various methods of air injection tests were used in all boreholes to identify and characterize conductive fractures. Through analizing the distribution of permeability and fracture index around the room a zone of blast damage of approximately .5 m thickness was delineated. The effect of stress modification seems to extend farther into the host rock to approximately 3.5 m depth.

Jan 1, 1982

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By G. M. Ikeda, J. G. Sibakin

An investigation was carried out to determine the variables affecting the coiling temperature of strip in the 56-in. hot strip mill. After statistical treatment, equations have been derived to determine the temperature drop between mill and coiler for both full spray (top and bottom) and top spray only practices. The individual influences of each variable in the temperature drop were derived for both practices. Limitations of the present practices were shown and adjustments in cooling for increased rolling speeds were suggested. A method of estimating the required number of sprays, their spacing, pressure, etc., to achieve a desired temperature drop is developed. MAXIMUM finishing temperature of a hot strip mill is mainly determined by the rolling speed, gage, and the temperature of the bar entering the mill. This finishing temperature may be limited by the maximum admissible coiling temperature in cases when either the cooling facilities on the runout table are not adequate or, more generally, when the cooling capacity of the runout table and the production capacity of the continuous mill are out of balance. Some time ago, the balance between these two factors was not considered detrimental to production. Recently, a new drafting schedule was introduced which increased the production rate, the entry temperature, and hence the finishing temperature. Thus, the restriction of the maximum specified coiling temperature became an important factor for many of the thicker gages. An investigation of the factors determining the coiling temperature may be, therefore, of considerable importance. A brief description of the available equipment will be a useful illustration of the techniques and methods used for this investigation. The 56 in. continuous hot strip mill is composed of six 4-high stands each containing two 221/2-in. diam work rolls and two 45-in. diam back-up rolls. Either of the last two stands can be used as the finishing stand. Which stand is used is dependent on the total percentage of reduction to be taken over the whole train, i.e., on the entry thickness and the final gage. The characteristics of these last two stands are given in Table I. Table I. Operational Characteristics of Nos. 5 and 6 Stands No. .5 NO. 6 Maximum voltage GOO 600 Power, hp 30(10 W00 I normal, kilonmp 4.35 3.73 Rpm of motor and rolls ISO 15 0 ITS to 300 Spettl ot strip, fpm 333 6 to 376T.2 103) to 2062 The speed of the finishing stand varies with the amount of reduction, strip width, and the exit gage. Finishing speeds in general use for varying gages are shown in Table 11. These speeds may change with an increase or decrease in the entry temperature of the strip. Even though the maximum speed of No. 6 stand is shown as 2062 fpm, this has so far never been attained,

Jan 1, 1957

By C. F. Jenkins, G. V. Smith

Serrated plastic flow in stable austenitic alloys based on Fe/Ni has been shown to be related to the presence of carbon and/or chromium in the systems. Strength peaks and plateaus in the serrated-flow temperature region for a commercial alloy correlate with an increased dislocation content, arising, presumably, from enhanced multiplication as a result of a strong interaction between dislocations and solute atoms. The data generally support a mechanism controlled by migration of vacancies, with the energy for vacancy motion being modified by the presence of chromium. Chromium atom -dislocation interaction is responsible for effects above 500°C, whereas the defect interacting with dislocations between 200" and 500°C is suggested to be a carbon-vacancy Pair. ThE phenomenon of jerky flow, serrated flow, or the Portevin-le Chatelier (P-C) effect in austenitic stainless steels is usually attributed to substitutional at1,2 mospheres1,2 or to precipitates&apos;-4 which form at dislocations during plastic deformation. On the other hand, evidence exists which supports a direct inter-stitial-dislocation interaction mechanism for serrated flow in fcc Ni-C,5,6 Ni-H7-9 and in nickel-austenites containing carbon." The present work consists in a study of serrated plastic flow in stable austenitic al-loys. The effects of carbon and of chromium were investigated separately, and a commercial stainless steel with different levels of interstitial impurity concentration was studied in an attempt to delineate the combined effects of the alloying elements. EXPERIMENTAL TECHNIQUES a) Materials and Fabrication. A commercial AISI 330 stainless steel and several specially prepared aus-tenitic alloys have been studied. The experimental alloys were prepared by arc melting the constituents under purified argon. Analyses of the materials are given in Table I. The commercial alloy was obtained as 5/8 in. bar stock and rolled to 0.092 in. sq, with several intermediate anneals. At this stage some of the material was annealed in Pd-purified hydrogen at 1100°C to establish different levels of interstitial content. All other heat treatments were in vacuum (10-5 torr). The "pure" alloy ingots were swaged to 0.120-in. rod and annealed in Pd-purified hydrogen at 1100°C. The analyses for these conditions are also contained in Table I. Following the above treatment, the final wire sizes Table I. Chemical Analyses of Test Materials Hrin Hydrogen at Cr, Ni, Alloy 1lOO°C wt pct wt pct C, ppm* N, ppm* Type 330 As-received 14.78 33.25 430 300 Type 330 64 14.78 33.25 40 50 Type 330 200 14.78 33.25 27 21 Fe/35 Ni 72 - 35.10 <10 62 Fe/35 Ni 200 35.10 <I0 44 Fe/35 Nil15 Cr 72 14.95 34.94 <I0 61 Fe/35 Ni/15Cr 200 14.95 34.94 <10 45 Fe/35 Ni/C $ 35.OM 380 *Sensitivity: N t 5 ppm Ct10ppm. f Nominal Ni content. % A master NiC alloy was used in preparation of this material; courtesy of D.E. Sonon. were obtained by either swaging or cold drawing. The test results did not vary with these techniques. b) Specimen Preparation. Two sizes of specimen and two gripping systems were used. i) 0.070-in. wire with a chemically milled gage section: 0.75 in. long, 0.060 in. in diam. These were fastened into grips containing tapped grooves. ii) 0.050 in. wire, gage length 1.5 in. Ball bearings were welded to the ends of the wires and the gage length was taken to include all material between the welds. Socket-type grips were used with these specimens. With specimens of type ii), joining was performed in a specially constructed brass jig, under argon, and automatic timing was utilized in the procedure. No adverse effects of welding were noted. Specimens were encapsulated and solution treated for 1 hr at temperatures selected to produce the same average grain size, -50 µ. Annealing twin boundaries as well as normal crystal boundaries were counted. The temperatures used are listed in Table 11. Table 11. Specimen Size. Temperature of Heat Treatment and Resulting Grain Diameters for Test Materials Recrystallization Resulting Material Condition Temperature Grain Sue AISI 330 Not H purified 0.070 120O°C 45 to 55µ in, wire AlSl 330 H , pure, 0.070 in. 1150°C 45to55µ wire Fc/35Nil15Cr Pure, 0.070 in. wire 1000°C 45tossp Fe/Ni Pure. 0.070 in. wire 775°C 45 to 55µ Fe/Ni/C Pure, 0.050 in. wire 850°C 10 to 20p AlSl 330 Not purified, 0.050 1150CC 45to55p in. wire AlSl 330 ti, pure, 0.050 in. 1150°C 45to55p wire

Jan 1, 1970