Search Documents

By H. R. Peiffer

Composite alloys of silver and alumina are shown to resist flow above the melting point of the continuous matrix. The ability to resist flow depends on the fineness of the dispersion and the oxygen content of the silver. It is believed that the oxygen influences very strongly the bond between the molten silver and the finely divided alumina. RECENT needs for materials with high strength and creep resistance at high temperatures initiated mechanical property studies on dispersed phase materials to near the melting point of the continuous matrix material. Results' of these investigations have shown that certain of these materials do have promise for high-temperature applications. Experiments performed on composite materials of silver and alumina by the author have resulted in the discovery of an interesting effect above the melting point of the silver. In these materials the silver was continuous and the alumina very finely divided (Linde B). It was observed that these materials exhibited strength and resistance to flow above the melting point of the silver matrix. The purpose of this paper will be to describe these properties. METHOD OF PREPARATION The materials were prepared by mixing the proper amount of Linde B alumina and high-purity silver oxide. The alumina content was varied from 5 to 20 wt pct alumina in silver in 5 pct steps. The materials were mixed by blending the constituents in an ordinary food blendor using ethyl alcohol as a vehicle. Enough alcohol was added to the powders to form a mixture with the consistency of a thin mud. After blending for about | hr the material was dried and the silver oxide reduced by heating to 450 OC. The material was then pressed at 25 tsi into a -in. billets 3 in. long. EXPERIMENTAL PROCEDURE The specimens were horizontally supported at either end by knife edge supports of cold-rolled steel. This holder was then placed in a "globar" furnace and a chromel-alumel thermocouple placed very close to the specimen recorded its temperature to within 10°C. Each specimen was heated rapidly to 900°C initially. The specimens were held at temperature approximately 30 min and then the temperature was raised 50 deg. The procedure was repeated until deformation was noted. Photographs were made of the specimens at various temperatures and increments of time using a Polaroid Land camera. RESULTS Fig. 1 shows the 5 pct by weight "Linde B" alumina and silver material after reaching 980 °C. Failure occurred after 15 min at this temperature. There were two points of failure and silver collected at them. No additional flow of the molten silver was noted at any other place. Fig. 2 shows a 20 pct by weight "Linde B" alumina in silver specimen. After 30 min at 1400°C, bowing of this material was observed. Other concentrations of alumina were added to

Jan 1, 1961

By K. Huessener

This paper attempts a survey of the principles involved in the combustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years1 practical working experience as combustion engineer, which I trust will prove useful to my readers. HlSTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow, The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam, The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 1, 1916

By Jose M. Sobral

The approximate production of petroleum in the various fields and for the country as a whole is shown in the following table, the figures for the later months of the year being estimated. Among the developments of the year may be mentioned the finding by the Standard Oil Co. of a small production, about 6290 bbl., at Aguas Blancas in the Province of Salta near the Bolivian border, and of about 88,000 bbl. at Lomitas, near Tartagal in the same province. The Government (Yaciementos Petroliferos Fiscales) in the last four months of the year also obtained about 6290 bbl, from Quebrada Galarce. .The oil found in Salta is of good grade and while the quantity is small great hopes of larger production are entertained. Approximate Total Argentine Production for 1928 Barrels Barrels Comodoro Rivadavia............................... 8,165,615 Plaza Huincul..................................... 783,514 8,949,129 Distribution of Production Government, Comodoro Rivadavia................... 5,165,159 Government, Plaza Huincul......................... 306,166 5,471,325 Private, Comodoro Rivadavia....................... 3,000,456" Private, Plaza Huincul............................. 477,348b 3,477,804 a The companies represented are Astra, 649,474 bbl.; Oriente, 42,237; Ferrocar-rilera, 1,337,380; Comp. Indust. y Comm., 609,092, Solano, 64,158; Diadema, 298,114. b Standard Oil Co. and a few smaller companies, Exploratory drilling has also been conducted around the Comodoro Rivadavia field. The Government is drilling at Vuela del Senguer south of Colonia Sarmiento and about 200 km. west of the main field hut the prospect of success is not as yet large. The country around Castillo, where the Royal Dutch Co. has property, is regarded more favorably. perhaps the most interesting event of the year was the discovery of a productive horizon at Comodoro Rivadavia about 200 m. below that previously exploited. This new horizon was found by the Ferrocarrilera Co. at 769 m. in its well No. 81, the previous yield for this

Jan 1, 1929

By H. I. Aaronson, C. Laird

Cold rolling by 50 pct a A1-4 pct Cu alloy containing many 0' plates has been found to accelerate markedly the transformation of 8' to 0 upon further aging. Although the basic mechanism of this transformation remains unchanged by plastic deformation, the nuclea-tion kinetics of 8 become appreciably more rapid and also less dependent upon temperature. Particularly at lower aging temperatures, rounded idiomorphs replace several faceted rnorphologfes. The rates of growth of 9 idiomorphs in deformed specimens aged at 300°C are appreciably more rapid than simple volume diffusion control allows. This observation is shown to be explained by an excess vacancy, rather than by a dislocation Piping mechanism of growth. ThE rather complex phenomenology of the 8' —8 transformation in Al-Cu alloys has been recently elucidated in considerable detail by means of transmission electron microscopy.'-4 This technique was also employed in the present investigation in order to examine the effects of plastic deformation upon the transformation of 8' to 8. The mechanism of the transformation in undeformed Al-Cu alloys has been established as the following sequence of events.1"4 The first step is the nucleation of 9 at (Y:8' boundaries. Nucleation of a 0 crystal takes place, however, at only a very small proportion of the 8' plates present. Each 0 crystal simultaneously consumes the host 8' plate and the a! in the immediate vicinity, with growth into a being the rate-controlling process. The remaining 8' plates are then dissolved as they fall under the concentration shadow of the growing 8 crystals. The evidence on the effects of plastic deformation upon these processes is intriguing, but much less detailed. The careful X-ray studies of Graf and Guinier have shown that the aging times required to form detectable amounts of 8' and 8 are reduced by prior cold working. Thomas and Nutting confirmed these results by replication electron microscopy. Nile-shwar,* on the other hand, reported that creep deformation decreases the rate of formation of 0. While this difference may have been caused by the use of concurrent rather than successive deformation and ag- ing, the X-ray technique which he used was able to monitor only the 0 phase. It is thus possible that the times needed to form 8' were increased moreg than the kinetics of 8' — 8 transformation were accelerated. At 90 pct deformation by cold rolling, Graf and Guinier found that the usual 0' —0 8 sequence is reversed: 0 forms first. von Heimendahl 10 confirmed this result with transmission electron microscopy. Pollard and Nutting, 11 and more recently Driver and Barrand, 9 having used the same technique, report that 9 also forms first during creep deformation. In the present study, the maximum amount of deformation was limited to 50 pct reduction by cold rolling in order to insure that 8 formed principally by the decomposition of . I) EXPERIMENTAL PROCEDURES This investigation was conducted on an Al- 3.93 pct Cu alloy, prepared as previously described. 4 Morphological and crystallographic effects of plastic deformation were studied in specimens annealed 6 hr at 548°C, quenched, and then aged for either 3 or 8 hr at 250°C to form large numbers of 0' plates. After cold rolling to a 50 pct reduction in thickness, the

Jan 1, 1969

By Heinz W. Duddeck, Hans-Konstantin Nipp

The design of storage space or deep mining in rock salt should take into account not only time dependency of the rock salt behavior but also temperature effects. For deep mining of potassium salt the natural increase of temperature with depth may no longer be negligible. For the storage of cryogenic liquid gas in salt caverns more knowledge is nezded about the propagation of deep temperatures and their effects on the stress-strain-creep behavior of the surrounding salt. High temperature problems arise for nuclear waste storages in caverns or drill holes emitting radiation. A numerical model is proposed for the analysis of displacements and stresses including their time and temperature induced change. For the material behavior of salt constitutive equations are chosen composed of a combination of Hooke-Kelvin-Bingham-Newton-model based on experimental results (excluding at present deep cooling), Langer 1980. The parameters involved are depending on the stress level and the temperature. The finite-element-method is applied to rotationally symmetrical three-dimensional problems. The non-linear calculation method is based on an implicit method with respect to time. A modified Newton-Raphson-method and the initial strain approach are employed. Along with some experiences on suitable numerical procedures, examples are shown for the characteristical effects of time-temperature dependency. Having achieved convergency and reliability a method is now available for practical design and parametric sensibility studies.

Jan 1, 1982

By James A. Beck

Phosphorus is essential to all life processes and therefore to the existence of man. In this role, there are no substitutes for phosphorus. In a commercial sense, phosphorus and its compounds are important to our entire economy, both in agricultural and in nonagricultural applications. The world's phosphate requirements are met by mining phosphate rock. Two general types of phosphate ore deposits are commercially important-igneous and sedimentary. Igneous deposits generally are more difficult and more expensive to mine than sedimentary deposits and are of importance mainly in the USSR, North Vietnam, and South Africa. Approximately 15% of current world production comes from these deposits. Over 80% of world production is from the pellet sedimentary deposits of Florida, North Africa, and elsewhere. Guano, the second type of sedimentary deposit, is produced in South America but is declining in world importance. Production Production of phosphate rock was reported in 31 countries during 1972. However, about 80% of world output is produced in three countries: the United States, the USSR, and Morocco (Table 15.2A.1). Throughout the past 20 years, between 75% and 80% of world output has been produced by these three leading countries. Between 1948 and 1972 world production increased at an average rate of 10% per year, from 21.5 to 103.9 million tons. Growth was quite steady at 6% per year through 1963, but in the 5 years from 1963 to 1968 production increased 11 1/2% per year. Since 1968 production has increased about 91/2 % annually. Since 1948 several new phosphate mining ventures have been developed in Senegal, Togo, Israel, and North Vietnam. In the same period, only one important phosphate deposit, on Makatea Island, has been mined out and closed. A number of other phosphate mining ventures are in various stages of planning and development. The most important new venture in phosphate mining is in the Spanish Sahara. New mining capacity is expected also in Syria, and serious investigation is in progress in Peru, India, Turkey, and Australia. Major expansion of existing operations is expected in Morocco, Russia, Tunisia, Israel, and Jordan. Consumption Historical data on world consumption of phosphate rock are not available in detail, but world consumption of phosphate has closely paralleled world production in the past two decades. The United States is the world's largest user of phosphate rock, accounting for 30%

Jan 1, 1976

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By K. R. Carson, J. Weertman

An attempt is made to ascertain the mechanism of tangle and cell formation and its dependence upon dislocation-interstitial carbon interactions. The strain-hardening behavior of single crystals of 3.25 pct Si-Fe was determined at 300° and 425°K and under conditions of both continuous and interrupted tensile strain. Significantly enhanced hardening was observed in crystals deformed at the elevated temperature, and it was further accentuated by interrupted straining. Transmission electron microscopy was used to study the resultant dislocation structures. Strain aging was found to aid tangle and cell formation at 425°K, but at both temperatures embryo tangles formed solely from primary glide dislocations, presumably by a process involving cross slip and "mushrooming". IN the course of plastic deformation all bcc metals and alloys develop a dislocation structure characterized by loose-knit groups of tangled dislocations. With increasing strain the tangles become more tightly knit and grow larger; finally a three-dimensional cellular substructure is formed:1 This process has been observed with the transmission electron microscope.'-l7 However, most investigations were confined to the study of nearly pure polycrystalline metals at relatively low temperatures. At intermediate temperatures, 0.17 to 0.14 Tm where T, is the melting temperature in degrees absolute, the mobility of interstitial impurities such as carbon is high enough to permit migration to nearby glide dislocations but is still low enough so that a significant drag force is exerted.18,19 it is also in this temperature range that a hump occurs in the curve of work-hardening rate vs temperature for iron. Analogous plots for tantalum" and columbiumzo show a definite upward trend in the work-hardening rate. Keh and Weissman1 have pointed out that this behavior may be explained solely on the basis of changes in the dislocation configuration: at low temperatures the dislocations tend to be relatively straight and uniformly distributed, but at intermediate temperatures tightly knit tangles and cellular substructure appear. The interference of these tangles with glide dislocations causes the observed increase in the work-hardening rate. This explanation appears reasonable, yet one might ask what factors cause tangle formation to be so favorable at intermediate temperatures. It seens likely that the strong dislocation-interstitial interactions which are known to occur in this temperature range are at least partly responsible," with the magnitude of the effect being proportional to the interstitial concentration. The purpose of the present work is to study the relationship between tangle formation and strain hardening in a bcc metal in the temperature range 0.17 to 0.4 Tm. Particular emphasis was placed upon a study of the effects of interstitial-dislocation interactions. Single crystals of 3.25 pct Si-Fe containing about 200 ppm of C in solid solution were used in the investigation for the following reasons: 1) The mobility of interstitial carbon in 3.25 pct Si-Fe is negligible at 300°K but increases rapidly at slightly elevated temperature22. Hence, differences between the flow curves and dislocation structures of crystals deformed at 300°K, 0.17 T,, and crystals deformed, say, at 425°K, 0.24 Tm, should be appreciable because of the enhanced dislocation-carbon interactions at the elevated temperature. This effect was accentuated in some samples by interrupted straining, thereby introducing a certain amount of aging. 2) Near room temperature, slip in suitably oriented 3.25 pct Si-Fe single crystals is largely confined to the (110) planes.23'24 Dislocation structures formed under conditions of single glide are the least complicated and their method of formation is the most easily discernable. 3) Dislocations in Si-Fe can be tightly locked with carbon atmospheres by a low-temperature aging treatment. The subsequent thinning of samples to foil thicbess causes little or no rearrangement in the dislocation structure.25 EXPERIMENTAL PROCEDURE Large single-crystal sheets of 3.25 pct Si-Fe were donated by Dr. C. G. Dunn of the General Electric Research Laboratory, Schenectady, N. Y. The orientations of the sheets were determined and slabs 1.0 by 0.25 by 0.05 in. were cut such that the desired tensile axis corresponded to the long dimension. The slabs were mechanically polished and subsequently decar-burized by heating at 1000°C for 3 days in a flowing wet-hydrogen atmosphere. A carbon content of about 200 ppm was introduced by heating at 805°C for 25 min in a flowing atmosphere of dry hydrogen containing heptane vapor. Shaped copper tools were then used to spark-machine at 0.125 by 0.50 in. gage length onto each slab. Vacuum annealing at 1225°C for 2 days followed by a quench into the cold end of the furnace to retain carbon in solid solution concluded the soecimen preparation. Continuous tensile flow curves for crystals of severa1 orientations Were obtained both at 300' and 425°K. A strain rate of 6.67 x 10-4 Per set was used in these and all other tests. Crystals oriented for single glide, B and D in Fig. 1, were subjected to a 3.5 pct plastic elongation to insure uniform slip along the gage length; they were then immediately subjected to interrupted strain cycling as indicated in Fig. 2(a). Each cycle consisted of unloading to 1.5 kg per sq mm, holding

Jan 1, 1969

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By Frank C. Greene

The principal event in the development of oil and gas in Missouri in 1942 was the drilling of the Cities Service Oil Company's No. I Jim Cook, in the northwest corner, NW. 1/4 sec. 32, T. 65 N., R. 39 W., Atchison County, in the northwest corner of Missouri. This well, not yet completed, bailed several barrels of free oil in about 27° Baume from a sand called the Bartlesville by those in charge, at a depth of 1450 ft. The well is on a block of leases obtained after the area, which is covered by several hundred feet of glacial drift, had been prospected by core drilling. Earlier in the year the same company drilled a well on the Glen Gray farm in the southwest corner, SW. 1/4 sec. 29, T. 65 N., R. 39 w., to a depth of 2427 ft. in the Hunton lime with a rotary drill. Oil stains in this hole led to the drilling of the second well. Table i .—-Wells Drilled for Oil and Gas in Missouri in 1942 Country Number of Number of County Oil Wells Gas Wells Dry Andrew.......... Atchison.......... I Bates............ 2 6 Caldwell.......... I 3 Cass............. I Clinton........... I Holt............. I Jackson.......... I I Knox............ I Nodaway......... I Platte............ 4 4 Ray.............. 5 Sullivan.......... I Totals.......... I 7 28 Otherwise drilling in Missouri was uneventful, with a total of only 36 Completions, of which one was a very small oil well, Seven were small gas wells and 28 were dry holes. The total footage drilled was 24,7541/2 ft., of which 14,0281/2 was by cable tools and 10,726 ft. by rotary. Twelve of the dry holes were drilled into Mississip-pian or older beds. Table I gives a summary of activities by counties.

Jan 1, 1943

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

IT is customary to make an alloy of copper in the same way, not to increase its quantity as with gold or silver, but to corrupt it for the art of casting and to destroy a certain natural viscosity in it. For this result it is accompanied by tin and also, sometimes, brass. But its proper and true alloy is fine tin, except, however, when you wish to make hammered works. For these, copper must be pure and without any trace [of impurity], otherwise it cannot be hammered thin, gilded in the fire, drawn into a wire, or made into vessels for use as is customary; but in casting, tin is almost essential. When you come to this association, just as it changes nature and appearance according to the proportion of tin which you give it, so it changes name and is no longer called copper but bronze, or, for a greater distinction of the quantity of tin for every hundred or more of copper, it is called by skilled workmen metal of more or less fineness as it contains more or less tin. This is recognized by the whiteness and brittleness: changing from red, which is the color of copper, it becomes white; from soft and flexible it becomes hard and brittle as glass. This admixture removes it so far from its original nature that one who does not know that it is a compound material believes it to be one of the number of metals engendered by Nature. Now, so that you may understand well, I tell you that various kinds of this are made, all according to the proportions of the quantities and according to the kind of work. For one kind of bronze is desired by those who make statues; this is not desired by those who make artillery or by those who make bells, mortars, basins, and similar cast objects. Now in order to alloy it into the species of bronze, eight, nine, ten, up to twelve pounds of tin are put with every hundred pounds of copper. Those who want it to make bells put twenty-three, twenty-four, twenty-five, and twenty-six, depending on the tone, on whether they are large or small in form, and on whether they wish to make the tone deep or sharp and clear. From twelve upwards is used for all other works that need it, either for hardness or to give them fluidity in casting by surpassing the degree of

Jan 1, 1942

By R. H. Hiltz

Three titanium alloys, known to provide a mechanically unstable p structure after quenching, were selected as material for a study of the Origin and nature of stress-induced transformation. Data from hardness and tensile tests were used to study the initiation of marten site and the effect of the transfornation and transformation products on the mechanical properties of B titanium, particularly the stress-strain relationships. With the exception that the materials investigated showed a natural aging reaction in the P condition, their behavior is analogous to that of' stress-transforming stainless steels. The transformation starts after initial yielding and is essentially complete just prior to .maximum loading. Once initiated, the martensite itself is capable of propagating the transformation. The deforn-ing materials show low strength, high ductility, and a high strain-hardening exponent. In metallic systems which undergo a diffusionless transformation on cooling, it is possible to produce a similar transformatiorl by plastic deformation under special conditions. Dewez' in delineating Ms temperatures for the titanium-rich end of most titanium binary systems:, established the point of intersection of Ms with room temperature for those particular alloys. Alloy compositions which would quench to mechanically unstable p were established from these data. The first investigation into the possibility of stress-induced transformation occurring in titanium met with little success. It was concluded that such a transformation in titanium was possible only under very special conditions. Continued effort in this direction, however, showed certain Ti-Mo binaries to be highly susceptible to this phenomenon. This fact was utilized by Liu to study the habit planes of martensite and by Machlin and wenig5 to study the effects of stress and plastic deformation on the P to a prime transformation in titanium alloys. The first investigation of the mechanical properties of these alloys was conducted by Holden and his coworkers at Battelle Memorial Institute.' The potentiality of the alloys i3s sheet-forming material was recognized, and the data reappeared in a survey of this type of titanium material.? The initial optimism was tempered by the difficulties in obtaining homogeneous 2i-Mo alloys in commercial-size ingots. The increasing need for good sheet-forming material kept investigation in this direction active, resulting in the development of a commercial alloy of this type.' This study was undertaken to obtain a clearer picture of the mechanism of stress-induced transformation in titanium. MATERIALS AND TEST PROCEDURE Three alloys were selected for this investigation: one a Ti-Mo alloy; another a Ti-Cr-Mo alloy, known to deform martensitically; and the third, a Ti-V alloy with an Ms below room temperature and an Md above room temperature, but known to contain w phase in the quenched condition. The compositions of these alloys are given in Table I. These alloys were cast as 5-lb experimental ingots, employing skull melting. The ingots were hot-forged into 1-in.-round bars. Two 72-in.-thick slices were cut from each bar for hardness testing; the remainder was cut into 0.252-in. tensile blanks. The tensile blanks and one hardness disc from each bar were heated in salt to a temperature 100°F above the 0 transus, held 2/2 hr, and brine quenched. X-ray analysis showed the pieces to be 100 pct 8.* *Omega cannot be distinguished from p by the technique employed. Tensile blanks were machined to size after this treatment. TO prevent transformation due to machining stresses, the shoulders and gage length were ground. True stress-true strain curves were

Jan 1, 1960

By Earl A. Trager

The broad picture of world petroleum production at the present time is one of an excessive supply. In any consideration of corrective measures to be applied in the future, it will be necessary to include all the producing areas of the entire world. To illustrate, United States production during 1931 was 48 million barrels1 less than 1930, whereas world production exclusive of the United States increased, owing principally to increases in Russia, Rumania and Persia. Domestic Peoduction Let us first consider the domestic production situation. Due to the fact that United States production was maintained below current demand, about 40 million barrels of oil were withdrawn from storage during 1931. Consumption increased about 1.5 per cent over 1930, which is less than the recent annual rate of increase of 8 to 11 per cent. If the machinery to prevent waste in the petroleum industry operative for more than a year will continue during the coming year and drilling is held to the 1931 level, there will be a decided improvement in the domestic situation by the close of 1932. This will be due in large measure to the drastic reduction in exploratory work and drilling which has been in effect for more than a year. Looking ahead for two or more years, probably there will be a shortage of domestic production in relation to domestic demand, unless there are discovered several large pools comparable to Oklahoma City or East Texas. Were the United States isolated, our problems in so far as petroleum production is concerned might be considered well along the road to recovery. To maintain this perspective will require the cooperation of foreign producers in the future, or protection of United Statcs markets from foreign invasion. Let us review briefly the present situation in the United States. East Texas has been the most important factor during 1931. The large initial production of individual wells and the rapid rate of drilling

Jan 1, 1932

By D. W. Mitchell

Mine fires are a serious hazard; surveys show that the coal-mining industry lags considerably behind industry in general in planning and training for fighting fires, and providing adequate fire-protection facilities. The results of the experiments discussed in this paper emphasize that every effort must be made to extinguish a fire in its incipient stage. The research also demonstrated that extinguishing agents and techniques, superior to those presently used in most operating mines, are available. An underground coal mine fire, if not extinguished quickly, can develop rapidly, create a serious hazard, and cause loss of life and property. The problem of controlling a fire increases in direct relationship to the time interval necessary to initiate control measures; as the fire increases in size and intensity it becomes progressively more difficult to cope with roof control, visibility, ventilation, and explosion prevention. Despite the constant vigilance of the industry, the number of coal mine fires is increasing. During the eight-year period, July 1952 to July 1960, following enactment of the Federal Coal Mine Safety Act, the Bureau of Mines investigated 401 fires that caused 30 fatalities and 75 injuries. More than half of these fires burned for more than one shift; 20 pct could not be extinguished by direct attack and had to be sealed. Agents and techniques for extinguishing simulated mining-machine and underground coal fires have been investigated in the Bureau's experimental coal mine. The research shows that visibility in the fire area is a primary factor affecting control operations. Associated with good visibility is accessibility to the fire; the closer the attack can be made, the less time and quantity of agent are required for extinguishment. Approach to the fire and visibility are hindered by the smoke and hot gases backing up against the ventilating current. In open entries an increase in air velocity assists in driving smoke ahead; at low airspeeds approach can be made by placing a brattice across the lower two-thirds of the entry, pushing the smoke ahead with water sprays, or discharging rock-dust from a rock-dust distributor. In a dead-end entry, fires can be approached by coursing fresh air along an airtight line brattice. However, it is safer, easier,

Jan 1, 1962

By D. R. George

Preliminary research has identified several organic and aqueous solutions that are effective absorbents for SO, from simulated smelter gas containing 0.3 to 2% SO2. These SO2 loaded solutions are also compatible to the reaction of H2S and SO2 to precipitate a readily filtered elemental sulfur. The economic removal of SO2 and production of elemental sulfur from stack gases discharged by base- metal smelters is a challenging goal. The magnitude of this task is illustrated by the estimate that about 3.5 million tons of SO2 are discharged to the atmosphere by smelters annually in the U.S. The SO2 concentration of the gases ranges from about 0.5 to more than 3%. As the sulfur content of SO2 is 50% a potential production of 1,750,000 tons of sulfur per year is indicated.

Jan 1, 1970

By James K. Stanley

PREFERRED orientation, particularly in irons and low-carbon steel, is a phenomenon that is both of considerable importance and theoretical interest. At times it is a liability and at other times an asset. In deep-drawing operations, preferred orientation is extremely undesirable because it necessitates trimming operations and increases scrap loss. Furthermore, oriented metals are likely to crack more easily than randomly oriented material because the forming of symmetrical and unsymmetrical shapes out of preferentially oriented metals and alloys increases the probability of rupture in regions of high stress, owing to differential ductility.1 In the electrical industry, on the other hand, preferentially oriented silicon irons are in demand for transformer application because of the improved magnetic permeabilities in the rolling direction.2 This phenomenon of preferred orientation in soft magnetic materials has been responsible for the tremendous improvement in transformer design and construction in recent years. Directional properties in metals have received a great deal of attention in the metallurgical literature,3-9 in which much of the information reported about orientation has been obtained by conventional methods, mechanical properties and X-rays. A wealth of data has been obtained and often at a great expenditure of time. The recent introduction of the magnetic torque measurements on ferromagnetic materials provides a very simple and rapid method of evaluating orientation. The judicious use of the method can supply important in- formation, but it should be borne in mind that such studies must be supplemented by X-rays, optical methods,10 and etch and pressure figures" to get a rational under- standing of the orientation phenomena. No claims are made that the magnetic torque of evaluating orientation will reveal the behavior of the metal in deep drawing. For this purpose the accepted tests for deep-drawing quality must be used. For a good drawing 'stock, which must have low impurities, desirable grain size, ductility, strength, hardness, good surface, random orientation, and good recrystallization behavior, it cannot be expected that any simple test will be satisfactory for appraising all the factors. The only factor on which the magnetic method can be used is orientation, which is, of course, of considerable importance. When directionality can cause a 10 to 15 per cent change in tensile strength and a IOO to 300 per cent change in tear length,12 it goes without saying that a reliable as well as rapid method for detecting these changes would be desirable. There are certain inherent advantages in testing orientation by the torque method: The method is rapid with the proper type of equipment; no elaborate preparation of specimens is required-it is only necessary punch or machine a disk of the sheet material and insert it into the testing device.

Jan 1, 1943

By N. D. Shutler

This paper describes a numerical mathematical model of the steamflood process that depends on fewer restrictive assumptions than models previously reported. The solution, however, is obtained economically. Example calculations are presented that, on comparison with experimental results, tend to validate the model. Results that expose certain process mechanics are discussed. The model describes the simultaneous flow of three phases — oil, water and gas — in one dimension. It includes the effects of three-phase relative permeabilities, capillary pressure, and temperature- and pressure - dependent fluid properties. Interphase mass transfer of water-steam is allowed, but the oil is assumed nonvolatile and the hydrocarbon gas insoluble in the liquid phases. The model allows heat convection in one dimension and two-dimensional heat conduction in a vertical cross-section spanning the oil sand and adjacent strata. The hydrocarbon-steam gas composition is tracked, but the effect of gas composition on water-steam phase behavior is neglected. The model is solved numerically in three separate stages. The three-phase mass balances are solved simultaneously using Newtonian iteration on nonlinearities occurring in the accumulation terms. The energy balance is solved separately by noniterative application of the alternating-direction implicit procedure. Separate solution of the composition balance is accomplished by straightforward solution of the finite difference equations. The method of effecting nonsimultaneous, stable solution of the mass and energy balances is the key to the success of the model. INTRODUCTION Mathematical tools as well as laboratory and field experiments are necessary to help us understand the complex steamflood process. A mathematical model can expose process mechanics and show the relative importance of process variables, but this ability is often limited by restrictive assumptions. Most known models of steam processes,l-5 with the exception of the model of Gottfried,6 are "simplified" in that they involve analytic approximations and require many restrictive assumptions. The primary utility of these methods lies in the routine use as an aid in engineering design. By contrast, the comprehensive model presented here is numerical and requires far fewer restrictive assumptions. It finds its primary utility as a research tool. It serves as an aid in understanding the nature of the process, in interpreting laboratory experiments and in evaluating and developing simpler mathematical models for engineering design. The major reason why previously presented models have been confined to the "simplified" class is evidenced by the one published exception. In 1965, Gottfried6 presented a numerical model for the combustion process of which the steam process is a subset. The result is a comprehensive tool (though it neglects capillarity and two-dimensional heat conduction) that is troubled with convergence problems and that requires 2 to 3 hours of IBM 7094 time to complete a calculation. Though our present model does not simulate combustion, it does consider capillarity and two-dimensional heat conduction and it overcomes the convergence and computer-time problems. MATHEMATICAL DESCRIPTION OF STEAMFLOODING FLUID FLOW The equations employed to describe three-phase fluid flow are of a familiar form. Darcy's. law provides expressions for the velocities of the three phases (oil, water and gas), which, when combined with oil, water and gas mass balances, give the partial differential equations governing flow of the

Jan 1, 1970

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 million yr (m.y.) ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. A total of more than 200 km30f silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.0 m.y. ago, included resurgent doming and intrusion in the south-central part of the caldera. Three to 4 m.y. later (-1 2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited silica, cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma, or connate water, or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury and other elements has not been identified.

Jan 1, 1977

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,' dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951