Search Documents

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Members, that the clues of the year 1918 will be payable on Jan. 1. 191.8, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of 83 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half morocco binding. The dues of Junior Members are $5 per year.

Jan 12, 1917

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Associates, that the dues of the year 1919 will be payable on Jan. 1, 1919, at the office of the Secretary. The clues for Members and Associates are $12 per year and the sum of. $2 additional is asked of those Members and Associates who desire to 'have the two volumes bound in the Institute's standard binding. The clues of Junior Associates are $5 per year.

Jan 12, 1918

In accordance with the provision of the Constitution, notice is here given to all Members, Associates, and Junior Members, that the dues of the year 1918 will be payable on Jan. 1, 1918, at the office of the Secretary. The dues for Members and Associates are $12 per year and the sum of $3 additional is asked of those Members and Associates who desire to have the three volumes bound in the Institute's standard half-morocco binding. The dues of Junior Members are $5 per year.

Jan 1, 1918

By Robert Mehl

THE Widmanstätten figures found in the steels have been long recog-nized and in some aspects carefully studied,1 especially as they occur in cast hypoeutectoid alloys. Aside.from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords, to, obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-stätten figure of unique interest from ;the crystallographic viewpoint, particularly in comparison with those formed on-slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By Charles S. Barrett, Robert F. Mehl, Dana W. Smith

The Widmanstatten figures found in the steels have been long recognized and in some aspects carefully studied,' especially as they occur in cast hypoeutectoid alloys. Aside from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords to obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-statten figure of unique interest from the crystallographic viewpoint, particularly in comparison with those formed on slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By R. F. Stahl, W. A. Martin, R L. Huntington

A marked gravitational segregation of liquid has been observed to take place in a number of volumetric fields toward the later stages of their oil-producing periods. This phenomenon has been pronounced in thick, highly permeable sand formations such as those of the wilcox zone in Oklahoma City. This observation has prompted considerable research directed toward the semiquantitative determination of the equilibrium saturation distribution of oil vertically throughout a formation at final depletion. In this paper, data are also presented showing the transient distribution of liquid at different stages of the depletion period. Other experimental results show the effect of temperature on the drainage rates of water, Wilcox crude oil, and a close-cut heptane fraction. Intermittent drainage of liquid produced saturation gradients that might well be expected from the flow theories involved, Yields of the various liquids varied from 50 to 75 per cent of the original fluid content of the sand-packed (4 in. by 8 ft.) vertical tube. Introduction In certain volumetric Oil fields the performance of the reservoir during the latter part Of its producing life is governed to a large extent by the downward movement of liquid due to the force of gravity. This is especially true of formations having thick or tilting beds of uniformly high permeability, free of shale breaks. Laverett4 and Katz3 have presented original data and discussed the theory relating to the capillary and gravitational forces acting On liquids contained in a sand body. These investigators have pointed out the importance of such studies in the estimation of future reserves as well as the original fluid content of a reservoir. In this previous work, no data have been reported showing the history of saturation distributions during the drainage period. Since a knowledge Of these transients is helpful in obtaining crude Oil from such a reservoir, the authors have obtained these data during this investigation. Experimental Apparatus The drainage tests were carried out in two vertical tubes, 8 ft. high and consisting of 2-in. and 4-in. standard wrought-iron pipe, respectively. Each tube was equipped with a water jacket, which could be kept virtually isothermal ( ± 1.0ºF.). A diagrammatic sketch of the 4-in. tube and its auxiliaries is shown in Fig. 1. At 6 in. above the base of the tube, and at every foot above this point, core nipples were inserted through the water jacket. These nipples were closely fitted with steel-plug inserts during each drainage run. At the end of the run, these inserts were removed so that cores could be obtained from the sand-packed tube.

Jan 1, 1943

By R. F. Stahl, W. A. Martin

A marked gravitational segregation of liquid has been observed to take place in a number of volumetric fields toward the later stages of their oil-producing periods. This phenomenon has been pronounced in thick, highly permeable sand formations such as those of the wilcox zone in Oklahoma City. This observation has prompted considerable research directed toward the semiquantitative determination of the equilibrium saturation distribution of oil vertically throughout a formation at final depletion. In this paper, data are also presented showing the transient distribution of liquid at different stages of the depletion period. Other experimental results show the effect of temperature on the drainage rates of water, Wilcox crude oil, and a close-cut heptane fraction. Intermittent drainage of liquid produced saturation gradients that might well be expected from the flow theories involved, Yields of the various liquids varied from 50 to 75 per cent of the original fluid content of the sand-packed (4 in. by 8 ft.) vertical tube. Introduction In certain volumetric Oil fields the performance of the reservoir during the latter part Of its producing life is governed to a large extent by the downward movement of liquid due to the force of gravity. This is especially true of formations having thick or tilting beds of uniformly high permeability, free of shale breaks. Laverett4 and Katz3 have presented original data and discussed the theory relating to the capillary and gravitational forces acting On liquids contained in a sand body. These investigators have pointed out the importance of such studies in the estimation of future reserves as well as the original fluid content of a reservoir. In this previous work, no data have been reported showing the history of saturation distributions during the drainage period. Since a knowledge Of these transients is helpful in obtaining crude Oil from such a reservoir, the authors have obtained these data during this investigation. Experimental Apparatus The drainage tests were carried out in two vertical tubes, 8 ft. high and consisting of 2-in. and 4-in. standard wrought-iron pipe, respectively. Each tube was equipped with a water jacket, which could be kept virtually isothermal ( ± 1.0ºF.). A diagrammatic sketch of the 4-in. tube and its auxiliaries is shown in Fig. 1. At 6 in. above the base of the tube, and at every foot above this point, core nipples were inserted through the water jacket. These nipples were closely fitted with steel-plug inserts during each drainage run. At the end of the run, these inserts were removed so that cores could be obtained from the sand-packed tube.

Jan 1, 1943

By C. Baldwin Sawyer

J. S. Vanick,* Washington, D. C. (written discussion).—To those who have been confronted with the study of the gas-metal reactions, this paper is a most welcome contribution. My personal interest in work bearing upon this general problem, stimulated by an appreciation of the difficulties inherent to problems of this type, prompts a few words of discussion. Table 2 of the paper shows a gradual increase in the nitrogen content with an increase in pressure, and an interpretation follows in which nitrogcn is used as the compressed medium when the conditions admit that cyanogen gas could be active as a contaminating ingredient. Fusions of electrolytic iron made in the induction furnace in an atmosphere of deoxidized nitrogen and out of contact with contaminating materials have shown no microscopic evidence of -a nitrogen increase; using a refractory-lined graphite crucible in the furnace under the same conditions or admitting air often resulted in the occurrence of nitride needles in the solidified melt. These results suggested that a nitrogenous compound served as a vehicle for the introduction of nitrogen and that such compound was not available when the pure gas and carbon-free refractory were used. The fusion of pure iron in pure nitrogen is perhaps a matter of theoretical interest. The author's work serves a more practical purpose when applied to steels rather than iron. Table 2 reports the absence of nitride needles in melts made under pressure of one atmosphere, although the quantity of nitrogen present would seem to exceed microscopically detectable percentages. In some recent work29 on carburized iron, nitride needles have been observed in areas analyzing as low as 0.015 per cent. nitrogen. This low percentage of nitrogen would indicate that the solubility limit is less than 0.030 per cent. for hypoeutectoid steels. There is the possibility that the areas of pearlite which exist in a hypoeutectoid steel restrict the distribution of nitrogen and limit its presence to the ferritie fields. In view of this work and the references quoted by the author, I am led to expect that the value for the solubility of nitrogen in solidified iron may approach

Jan 1, 1924

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961

By D. Turnbull, J. H. Hollomon

THERE is a large body of evidence'" indicating that solidification during the liquid-solid transition is usually induced by heterogeneities present in the liquid. By dispersing liquid metals into small droplets, the impurities responsible for catalyzing solidification are isolated within a small number of these droplets. The effect of the foreign body therefore is restricted to a single drop by this technique. Thus upon cooling below the melting temperature, solidification is initiated by homogeneous nucleation in the majority of the droplets that do not contain impurities. In the case of solidification of liquid metals, the activation energy for nucleation is so great that its rate changes by orders of magnitude for a change in temperature of only several degrees centigrade.' Effectively homogeneous nucleation occurs at a critical temperature upon continuous cooling. Thus by microscopic observation of single particles during cooling, a temperature at which the rate of homogeneous nucleation becomes sensible can be determined.3 since at the temperatures at which nucleation occurs in the absence of impurities the rate of crystal growth is extremely rapid, the temperature at which the entire particle solidifies is very nearly the temperature at which the nucleation of the solidification occurs. Thus for liquids that freeze at high temperatures the onset of nucleation can be established by simply observing the temperature at which the marked heat evolution and increase in brightness of the particle occur. For liquids that freeze at lower temperatures the onset of nucleation can be determined by a rumpling and change in shape of the particle resulting from its solidification. The microscopic technique for observing the solidification of small particles has already been described." In earlier papers the nucleation of solidification of pure metals 5,6 and of alloy systems7 showing complete liquid and solid solubility have been described. In the present paper, the observations are extended to a simple eutectic system (Pb-Sn) where the possibility of the formation of two solid phases exists. Metals for the investigation were obtained from the American Smelting and Refining Co. in the form of pure lead and pure tin, 99.8 and 99.9 pct purity, respectively. An ingot of each of the pure metals was made into shot by heating the metals at a temperature about 50 °C in excess of the melting point and pouring the liquid slowly into a container of water at 15°C. Samples of the shotted pure metals were weighed out to make alloys containing 5, 10, 15, 20, 25, 30, 40, 50, 60, 70, 80, and 90 atomic pct Pb. Samples of each alloy were then melted in separate beakers. Each melt was poured through a pyrex funnel into a cylindrical mold (% in. ID). The casting solidified in 10 to 20 sec. The inside of the mold as well as the funnel through which the metal was poured were coated with graphite to eliminate adherence of the metal. Analyses were performed on some of the compositions and are given in Table I. The compositions also were checked for these samples and for those that were not analyzed by determining the spread between the liquidus and the solidus upon melting the small metal particles. These measurements agreed as well with the nominal compositions as the analyses listed above. Results The results of the supercooling experiments for the several alloys are summarized in Table II and plotted on the constitution diagram in Fig. 1. Data for the pure lead and pure tin were taken from earlier investigations. The values for the maximum supercooling of the several alloys are the average of several determinations on a number of drops of each alloy. The maximum value in any determination was within about 2 pct of the average. For the alloys containing from 20 to 60 atomic pct Sn, inclusive, two marked changes of the surface structure were observed upon cooling. At the higher temperature, after the first appearance of the solid phase it continued to grow slowly at a constant temperature and then stopped. At the lower temperature the alteration of surface structure was abrupt. For the alloys containing from 70 to 95 atomic pct Sn, inclusive, an abrupt change in surface structure was observed at a single critical temperature.

Jan 1, 1952

By Harold Rabling

The following notes are taken from results obtained on a standard 25-ft. Hancock jig1 tested during regular operation in the Bonne Terre mill of the St. Joseph Lead Co. The object of the tests was to determine the conditions for most effective work, and the nature of products that could be made. The material treated was sized between 9-mm. and 2-mm. round-hole screens, and was constant throughout the experiments. Three products were made, concentrates from the first three hutches, middlings from the fourth and fifth, and tailing from the sixth. The middlings were crushed in one pair of Allis-Chalmers Style B, 30 by 14-in. rolls, and elevated with the original ore to the 2-mm. screens, oversize of which formed the jig feed. While this arrangement was very simple, it gave rise to undesirable crowding of the circuit. Table 1 shows tonnage and assay values of the jig feed and products at the beginning of the experiments, and brings out the excessively large amount of middlings, comprising 63.3 per cent. of the total material fed to the jig. The rolls, being heavily overloaded, did very little crushing, a screen analysis of the product showing that only 27 per cent., or 128 tons, was crushed fine enough to pass to the tables. The remaining 347 tons returned to the jig with 400 tons of original ore. At .times, this overcrowding became much worse, and the tonnage in circuit grew to enormous proportions. It became imperative

Jan 1, 1918

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper sample and maintaining tight air connections in bubble-tube piping.

Jan 3, 1950

By J. J. Egan

ADVANCES in the production of quality steel have emphasized the need for greater knowledge of the amount and distribution of oxygen in the steel. Control of inclusion content and quality is largely dependent on such knowledge. While many analytical methods have been de-vised for the accomplishment of this end, few are without serious limita-tions in accuracy, convenience, or skill required in application. Usually at least two methods are necessary to determine total oxygen and constituent oxides. Because of the great importance of this problem and the specific interest in the application of such methods of analysis, the various procedures were carefully reviewed at the Union Carbide and Carbon Research Laboratories, with the view of developing a method free from the limitations mentioned above. Intensive experimentation finally led to an improved iodine extraction analysis described by Cunningham and Price. I After this had been thoroughly checked from the standpoint of the analytical chemist, it was rechecked from that of the metallurgist. This involved preparation of a number of small heats of varying composition with determination of total oxygen in the molten metal by the alumina method2 and an analysis of the solidified material without the aluminum addition by means of iodine extraction; the oxides of iron, manganese, silicon and aluminum also being determined by the iodine analysis. The report of this work constitutes the subject of this paper.

Jan 1, 1933

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington' have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4' and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick's law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.' By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.' (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick's law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

By M. Van Hecke, Y. Berube, L. M. de Smecht

Nitrogen solubilities in water at 100, 200, and 400 psi, in the temperature range 100 to 175C, were determined using an automated system involving flash evaporation and gas chromatography. Rates of gas transfer into a standard laboratory auto-clave were measured by the same technique. The rates at which a gas can dissolve into such a reactor were found to be close to the rates of oxygen consumption observed during the oxidation of several mineral sulfides, indicating that gas transfer might be a rate-limiting step in autoclave leaching.

Jan 1, 1977

By D. C. Reynolds

Recent experiments with II-VI compounds have shown that they hazle considerable potential for laser applications over a broad region of the optical spectrum. It may be possible to cover the spectrum continuously from 3200A (ZnS) to the far infrared (CdHg:Te) since HgTe is a semimetal. At this writing laser action has been observed in ZnS, Zn0, CdS, CdSe, CdS:Se, CdTe, and some of the CdHg:Te alloys. Of particular interest are those lasers operating in the zlisible and near ultraciolet regzons of the spectrum where detectors of high sensitivity are available. The lasing transitions in II-VI compounds are bound exciton transitions some of which have been identified in auxiliary experiments. High efficiencies and low thresholds for lasing hare been achieved almost exc1usively in plutelet-type crystals. The greater crystalline quality exhibited by the phtelet-type material is shown to result from the crystal growth habit. Phonon scattering- of conduction electrons to the ground-state exciton is discussed ill relution to Lou thresholds and high efficiencies for lasing- observed in the CdS:Se solid solutions. The first successful semiconductor laser operation was achieved in the III-V compounds. It is possible to choose a material in this group that will operate between approximately 0.65 and 8.5 . There are at least two reasons why one would like to have a laser operating at shorter wavelengths. First, it would be easier to experiment with a laser operating in the visible region of the spectrum, and also more desirable to have high-in tensity visible light sources. Second, the most sensitive photomul-tiplier detectors are available in the visible and near ultraviolet regions of the spectrum. It is known that II-VI compounds are direct-band-gap semiconductors and as such offer the potential of operating at any specified wavelength between 3200 (ZnS) and 7772A (CdTe). Light emission from II-VI compounds has been the subject of numerous investigations for many years. These investigations were all primarily concerned with noncoherent emission. It has been only recently that coherent emission from these compounds has been observed. To date, laser operation has been demonstrated in CdS, CdSe, and the solid solutions of CdS:Se, ZnS, ZnO, and CdTe. These compounds cover an appreciable portion of the optical spectrum from the ultraviolet to the near infrared. In considering laser applications, the use of lasers in communication's systems offers many desirable features. In any operation of this type one must consider the losses in transmitting the radiation from the source to the detector. Atmospheric absorption in the visible and near ultraviolet is variable and greater than in certain regions of the infrared. It might be concluded that for long-range communication systems an infrared laser operating in a spectral region that is coincident with a transmission window in the atmosphere would be preferable. However, one cannot overlook the possibility of operating a system in the sensitive region of a highly sensitive photomultiplier detector or other light-amplifying system. LASER CONSIDERATIONS To produce a source of coherent radiation it is necessary to achieve a population inversion. In the case of semiconducting materials it is necessary to raise the electrons from one energy state to a higher-energy state relative to it. In semiconductors, this population inversion can be achieved by three different techniques: 1) Current Injection. This technique uses a p-n junction biased in the forward direction. Large numbers of electrons are injected from the n region into the p region, and recombination occurs close to the junction. An inverted population is obtained in this region and the recombination radiation propagates parallel to the junction. This type of pumping has been used in the GaAs junction-type lasers but has not been successfully employed in the II-VI compounds. 2) Optical Pumping. In this case, one uses photons to obtain a population inversion by exciting electrons to higher-energy states. The pump sources are flash lamps or arc lamps and, occasionally, other laser sources when such sources have the appropriate energy for exciting the electrons. The disadvantage of this type of pumping is that flash lamps put out a rather broad spectrum of radiation, whereas the laser material has a rather narrow region of absorption. This results in an inefficient process. Laser sources provide efficient pump sources but the number of usable wavelengths is limited. 3) Electron Beam Pumping. In this technique, the laser sample cavity is bombarded with electrons having energies in the range from approximately 10 to a few hundred kv. The bombarding radiation excites electrons from valence to conduction band states in the semiconductor, giving rise to an inverted population. This type of pumping has been used successfully in several 11-VI compounds.

Jan 1, 1968

By E. A. Stephenson

In spite of tremendous handicaps notable advances in production engineering have been achieved during 1932. The technique of deep well drilling has continued to progress, notably in California and at Big Lake, Texas. In the latter field a method has been devised by which two grades of oil in contact with each other are produced without intermingling. In rig design many improvements have been made whose objective is to facilitate deep drilling with reduced power losses and increased life of the equipment. Flush joint casing and drill pipe have been improved further, careful tests indicating that the drilling time can be reduced by from 5 to 20 per cent where flush-joint pipe is used. Slow-speed pumping has come into wider use, with further increases in over-all efficiencies. A number of improved well pumps also have been developed and are being tested. One of the most important of these is a positive displacement pump of the rotary type, directly connected to an electric motor placed in the bottom of the hole, and adaptable to various sizes of tubing and casing. In some localities the trend is towards the replacement of electric motors and large-cylinder engines by multiple-cylinder gas engines. Experiments have been conducted and critical analyses made of flow conditions in wells equipped with various styles of tubing which give promise that tubing may be designed to fit individual well conditions. In those wells producing at less than maximum capacity, the gas-oil ratio has been shown to depend on the rate rather than on the method of production, or the design of equipment. Important factors in the design of screened pipe have been carefully analyzed and made the basis of a method for determining the required mesh. Remarkable progress has been made in the use of subsurface pressure data. In East Texas particularly, use of such data is providing a means for the control and equalization of water encroachment and is also pointing the way to a sound means of allocating to individual tracts an

Jan 1, 1933