Search Documents

By R. E. Reed, R. D. Leggett, Paxton, H. W.

TECHNIQUES have been developed for growing monocrystals and bicrystals of Fe-20 Cr, Fe-20 Cr-20 Ni, and Fe-18 Cr-8 Ni alloys by both the strain-anneal and the Bridgeman techniques. None of the techniques are new but since they are simple and many people have expressed interest, they are described here quantitatively as they could be modified for other single-phase "commercial" materials of high melting point. CRYSTAL GROWTH BY STRAIN ANNEAL Flat tensile specimens with a tapered gage length were initially studied to deduce the approximate critical strain. Normal flat tensile specimens were then used. The optimum procedure for the austenitic steels (Fe-Cr-Ni) deduced from a variety of cold reductions, recrystallization treatments, tensile strain, and growth anneals was as follows: cold reduce 70 pct, recrystallize (after machining tensile specimens) at 1000°C for 1 hr, strain in tension 2.5 pct, and then heat to 1350°C as rapidly as possible. A time of 100 hr at 1350°C is usually sufficient to pro-

Jan 1, 1960

By G. J. Wolga, W. W. Tyler, A. C. Wilson

THE physical properties of uranium have been reviewed by Katz and Rabinowitch.1 Their review includes thermal conductivity data for ternperatures above 375°K. Recently, Mendelssohn and Rosenberg' have published data on the thermal conductivity of uranium from 2" to 20°K. Our measuremerits indicate the temperature dependence of the thermal conductivity in the temperature interval from 20" to 300°K. Electrical resistivity and thermoelectric power were measured on the same sample. The material studied was normal uranium which had been heated at 700°C in a lead bath for 10 min and then quenched in a water bath held at 50°C. From this material a rod M in. in diameter and 2 1/2 in. long was machined. Two 0.040 in. holes were drilled into the rod 1 3/4 in. apart. Copper-constantan thermocouples for temperature and potential measurements were soldered to copper pins which were pressed tightly into these holes. Details of the equipment and experimental techniques used in making the measurements have been described elsewhere." Fig. 1 shows micrographs of a section of the sample studied. Fig. la was taken with unpolarized light and shows impurity inclusions, probably uranium carbide. Fig. lb, showing the same field, was taken with polarized light and gives some indication of the grain size and twinning within the grains. Experimental Results Thermal conductivity and electrical resistivity data are shown in Fig. 2. Table I shows values of

Jan 1, 1954

By Gerald Edmunds

The liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the composition of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. Apparatus By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 13/4-in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 181/2 in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Gerald Edmunds

The liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the composition of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. Apparatus By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 13/4-in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 181/2 in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By T. D. Tiemann

The extraction of iron oxide from several types of siliceous iron ore by digestion in sulfuric acid solutions was investigated in the temperature range from 80 to 258°F at concentrations from 10-60% H2SO4. Degree and rate of extraction were found to be critical with respect to both temperature and acid concentration, requiring temperatures in excess of 250° F and acid concentrations of 50% to effect 80-90% extraction of iron oxide in 60 min. Rate of extraction is directly related to surface area and apparently controlled by the rate of chemical reaction. The activation energy was found to be approximately 25,000 cal per g mol. Extraction characteristics of the several ores were found to be similar. The Department of Minerals and Metals Engineering at the University of Wisconsin conducts a continuing research program to develop processes for the utilization of low-grade iron ore deposits such as the nonmagnetic taconites of the Wisconsin Gogebic range. Methods under study include high-intensity magnetic and high-tension electrical concentration, flotation, direct reduction and chemical extraction. Concentration of a number of low-grade siliceous iron ores by the extraction of silica in sodium hydroxide solutions has been reported by the writer and others in the literature.1,2,3,4 Residual concentrates containing as much as 65% iron have been obtained from taconites containing less than 30%. Currently an alternative approach is under study, namely the dissolution of iron oxides from siliceous gangue by extraction in acid, with subsequent recovery of the iron from solution. Such a process for extracting iron oxide from the low-grade oclitic deposits of Alberta with hydrochloric acid was investigated and described by Gravenor, Govett and Rigg.5 The current investigation, which is entirely devoted to extraction with sulfuric acid, is the subject of this paper. In part, the objective of this research was to determine the possibility of leaching iron ores in situ with sulfuric acid. The investigation of a recovery method is left to later research. The ores investigated contained hematite (Fe2O3) as the principal iron-bearing mineral and minor amounts of goethite (Fe2O3 .H2O), magnetite (Fe3O4), and iron-bearing silicates. The gangue was essentially quartz occurring as single crystals and microcrystalline aggregates. Detailed description of the ores may be found in the literature.1,2,4,6 A comparison of the specific ores used in this investigation is shown in the partial analyses of Table I. EXPERIMENTAL METHODS All extractions were made at atmospheric pressure using beakers with a mechanical stirrer for those tests run below the boiling point, and Erlenmeyer flasks for those at the boiling point. A thermostatically controlled hot plate was used for heating, and this maintained the mean temperature within the solution to within ±3°F during extraction. The sample of ore for extraction was weighed to + 0.02 g. For tests below the boiling point, the sample was added to the beaker containing the sulfuric acid solution at the desired temperature. For the boiling-point tests, the sample was added to the Erlenmeyer flask followed by distilled water and the

Jan 1, 1968

By R. L. Andelin, J. D. Knight, M. Kahn

Self-diffusion in single-crystal tungsten and diffusion of rhenium tracer in single-crystal tungsten have been measured over the temperature range 2660° to 3230°C by direct sectioning and radio-chemical analysis of W185 and Re183 and Re184 tracers. The initial radioactive layer was produced on the diffusion specimens by bombardment with 9.0-mev deuterons. Diffusion heating of the samples in high vacuum was accomplished by induction heating. Temperatures were measured by optical pyrometry, and the system was calibrated ALTHOUGH a considerable body of experimental information has been accumulated on self-diffusion in solids, the major part of the detailed work has by reference to the melting points of tantalum (2996°C), molybdenum (2620°C), niobium (2468°C), and rhodium (1966°C). The diffusion coefficients for the two systems, obtained by least-squares analyses of the data, are well-represented by the equations thus far dealt with relatively low-melting systems. Diffusion studies on the high-melting elements niobium,1 tantalum,2,3 and tungsten4'5 have been limited to polycrystalline material, for which data interpretation and theoretical analysis are sometimes difficult. Only recently, a study has been made with single-crystal molybdenum.6 The present work deals with the measurement of self-diffusion in single-crystal tungsten at temperatures approaching the melting point (3410°c).7 Since the method chosen for producing the radioactive tracer layer-bombardment with deuterons—produced detectable isotopes of rhenium as well as of tungsten, the diffusion of rhenium was measured also.

Jan 1, 1965

By Pradeep K. Rohatgi, Clyde M. Adams

Dendritic aggregate of ice formed on freezing of aqueous soluitions has been studied. Chlorides of sodium, potassiutn, lithiunz , and hydroget1 were used as solutes. The spacing between ice platelets or den-drites was experimenlally found proportzonal to the square root of freezing time when the freezing rate was constant from beginrting to end of solidification; the constant freezing rates were obtained during freezing of small droplets of aqueous soliitions surrounded by relatively large heat sinks. The transverse growth velocity of the ice platelets is proportional to the square root of the freezing rate. During unidirectional freezing from a constant temperuture chill, the solution at each location is subjected to a spectrum of freezirtg rates. The freezing rate is ini- FREEZING of solutions has been a subject of investigation in many disciplines. Aqueous solutions offer the advantage of transparenty; their study is of special significance due to the increasing interest in freezing processes for desalination. In addition dendritic solidification of aqueous solutions is in many ways analogous to freezing of metallic solutions. Aqueous solutions of most ionic salts freeze with tially low, passes through a maximum, and then decreases until solidificatimz is complete. The den-drite spacing increases linearly with the distance from the chill surface; it is inversely profiortional to the square root of the maximum freezing rate. The dendrite spacings in the two systems (the constanl freezing rate and the varying freezing rate) are equal, when the maximum freezing rate of the varying freezing rate system equals the average freezing vale of the constant freezing rate system. Mass transport in interdendritic liquid duriug solidificatiotz is analyzed; the experimental observations indicate that maximum concentration difference (AC) and supercooling (AT) in the interdendritic liquid are indepexdent of freezing rate. the separation of practically pure ice crystals from the liquid phase; with very few exceptions there is no solid solubility of ionic salts in ice. As an ice crystal grows there is rejection of solute from the moving interface into the liquid. Since the rejected solute moves primarily by diffusion, concentration gradients are established in the liquid. The highest solute concentrations are found in liquid immediately adjacent to liquid-solid interfaces and lowest concentrations farthest from the interface. Two-phase equilibrium obtains only at the solid-liquid interface; at other locations the liquid becomes supercooled because temperature gradients are negligible compared to concentration gradients. This is an immediate consequence of the fact that thermal diffusivities are considerably higher than mass diffusivities.

Jan 1, 1968

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By W. L. Finlay

Size effects in quenching steel are particularly prominent and well recognized because of the existence of a critical cooling rate separating nuclea-tion and growth transformations, as exemplified by the formation of pearl-ite, from the shear type of transformation characterizing the martensite reaction. The absence of a similar, sharply demarcating cooling rate is characteristic of precipitation hardening systems and size effects in these are correspondingly less prominent. This paper is concerned with a size effect in high-purity, precipitation-hardenable alloys which appears not to have been recognized previously. This effect is believed to result from the thermal fluctuations which inevitably occur in quenching a specimen of finite size into a cooling liquid rather than from the existence of a critical cooling rate. QUENCHING "ANOMALIES" The precipitation hardening literature contains many references to so-called anomalous quenching and aging results. By "anomalous", investigators usually meant that their alloys did not consistently harden on aging after quenching according to some anticipated pnttern: not infrequently virtually no age hardening occurred with compositions known to be precipitation-hardenable. Perhaps the most prominent series of anomalies was reported over a 15-year period by Gayler and coworkers on aluminum-copper.l,2,3,4 Working with silver-rich copper alloy, Cohen5 secured some very interesting Rockwell F hardness changes of from 1-5 Rockwell points between the first peak and valley. Fink and Smith borrowed one of Cohen's specimens and, following his heat treatment and quenching practice to the letter, secured6 very different results in which only one peak was obtained and in which the hardness level at the aging lime of Cohen's first peak was 20 Rockwell F points higher. Fink and Van Horn7 encountered serious deviations in age-hardening high purity aluminum-zinc alloys. They stated that "the discrepancies were larger than might be expected from possible experimental errors in the Brinell readings." Geisler, Barrett and Mehl8 likewise encountered anomalous hardening results in aluminum-silver alloys, securing quite different age-hardening curves from two identical specimens. They stated that "the treatments of these samples had been the same, so that the different behaviors could be attributed only to accidental variations in the quenching practice."

Jan 1, 1950

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By K. T. Aust

The relative interfacial energies of symmetrical tilt boundaries in silver of greater than 99.999 pct purity were measured as a function of orientation difference 0 between 9° and 36° about <001>. The results are in good agreement with the dislocation model of the grain boundary. The energy vs H curve may be represented by the Shockley and Read equation in the form Eoe (0.55—In 8). READ&apos; has indicated that an ideal experimental method of testing the predictions of the dislocation theory of the grain boundary would be to measure the interfacial energies of symmetrical tilt boundaries between face-centered-cubic grains that have a common <001> axis, as a function of orientation difference 0. The misfit H should be defined by a rotation of each grain through an angle of H/2 away from the boundary. Such boundaries might be expected, from geometrical considerations, to be made up of a series of edge dislocations, at least for small values of 0. Energy vs H relationships for tin&apos; and lead:&apos; were previously obtained for an asymmetrical tilt boundary separating two grains in which generally only one grain was rotated about a <001> specimen axis through an angle of H away from the boundary, the other grain remaining fixed. It is possible, however, that the boundary atoms in tin and lead may have attained a symmetrical position, in relation to the orientations of the grains on either side of the boundary, during equilibrium annealing. The two sets of measurements on silicon ferrite&apos; were somewhat better suited for comparison with theory, since the boundaries were symmetrical tilt boundaries in which the axis of relative rotation was <110> in the first series and <l00> in the second; but this alloy has a body-centered-cubic structure. Although the grain boundaries in silver" were symmetrically tilted, the axis of relative rotation was not a simple crystallographic direction, and it varied from boundary to boundary. Although the above measurements were in good agreement with the Shockley and Read equation,"&apos;: it appeared desirable to carry out experiments under the ideal conditions specified by Read.&apos; Consequently, the relative energies of symmetrical tilt boundaries in silver between grains that have a common <001> axis were measured. The technique of equilibrating grain boundaries in oriented tricrystals was used rather than the less satisfactory thermal groove method previously employed for silver bicrystals." Experimental Details and Observations The solidification and seeding techniques, described previouslyh for growing tricrystals of controlled orientations, were used to prepare tricrystal specimens from silver of greater than 99.999 pct purity. The silver was obtained from American Platinum Works, Newark, N. J., in the form of poly crystalline rods 10 cm long and 7 mm in diam. These rods were then cold worked by rolling or drawing them into suitably shaped blanks. Single crystal seeds and tricrystals were grown in a high purity graphite boat by means of a movable furnace with globar heating elements. The graphite boat was enclosed in a Vycor tube, which was first evacuated to about l00/u Hg and then filled with a static argon atmosphere. The maximum temperature outside the Vycor tube was 1250°C. A typical tricrystal specimen of silver is shown in Fig. 1. Grains B and C were grown from seed crystals with a <001> specimen axis or longitudinal direction parallel to the direction of growth and with another <001> direction perpendicular to the surface. Each of the two seed crystals was rotated 18" about the <001> specimen axis but in opposite directions away from the boundary. A symmetrical tilt boundary, therefore, separated grains B and C with an orientation difference 8 of 36" about <001>. Grain A in Fig. 1 was grown from the middle seed with a <110> direction parallel to the specimen axis and with a <001> direction inclined at 45&apos; to the surface of the specimen. The interfaces sepa-

Jan 1, 1957

By P. B. Barton, P. M. Bethke, R. O. Rye

Rhyolitic welded-tuff wallrocks of the epithermal base and precious metal veins of the Creede district were pervasively altered by the addition of more than two billion metric tons of potassium some 1.5-2 million years before mineralization. Sodium, calcium and magnesium were strongly depleted, yielding a nearly binary quartz + potassium feldspar assemblage containing as much as 13 weight percent K 0. This large-scale metasomatism, originally noted by Steven and Rattle (1965), took place progressively by initial alteration of plagioclase phenocrysts to orthoclase or microcline followed by alteration of the groundmass feldspar to orthoclase and gradual change of the sanidine phenocrysts to more Or-rich compositions. Oxygen isotope and chemical studies show that the metasomatism resulted from the interaction of the tuffs with deeply circulating heated ground water and suggest that the potassium metasomatism of rhyolitic rocks is the facies equivalent of propylitization of volcanic rocks of more basic composition.

Jan 1, 1985

By Leonard Waldo

The recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high as that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, text-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful. For mental calculation the easiest rule to convert centigrade into Fahrenheit is to add 32° to twice the centigrade reading less one-tenth of this product: Thus 1000&apos; C. = 2000" — 200" + 32" = 1832" F., and to convert Fahrenheit to centigrade, subtract 32" from the Fahrenheit reading, multiply by 10 and divide by 2 and 9 successively : Thus 1000° F. = 1000° — 32° = 968° X 10 = 9680° - 2 = 4840° - 9 = 537.77° C. Another and often very convenient method is by &apos;use of a graphic construction as follows :

Jan 1, 1913

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.&apos; The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By Ernest A. Hersam

Accurate ore-sizing with screens is drawing attention to certain details that now, more than ever before, require attention. There are many tests that must be preceded by careful sizing. The assayer often could profit by a more careful selection of screens. In milling, more attention is given the slimes produced. Cement-manufacturers are pulverizing and screening finer than they formerly did, and others are reducing materials to fine sizes at high cost, with screens used to govern the fineness of the pulverized product. Fine screens are expensive, easily injured by misuse, are carried in stock sparingly by most dealers, and are handled often by those who know little about them except their designated number. More attention, on the whole, needs be given the actual size of the mesh-openings, and less emphasis placed upon any custom or conventionality in numbering. An effort to classify wire screens, in this respect, leads at once into computations, where one is confronted with details of sizes and standards, of different wires, different gauges, and different customs. There is always uncertainty about the exact working-size of a screen until one gives the matter special attention, and devotes more time to it than its simplicity seems to demand. To know only the number is not sufficient for all uses. Often, in sets, superfluous sizes are used; and sizes are omitted that are of critical importance. In wire screens, the use of different standard sizes of wire makes important differences in dimensions that must be taken into account. The dealer usually grades screens by the number of openings per linear dimensions, regardless of the size of the openings or of the wire. Certain 100-mesh screens in use are found, by measurement, to be actually coarser than others of 90-mesh, a result which is due, of course, to the use of larger

Jan 1, 1907

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942