Search Documents

By John H. Hollomon, C. Zener

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By C. Zener, John H. Hollomon

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By R. W. Balluffi, R. Resnick

NUMEROUS investigations of chemical diffusion in a brass have been made and the results are collected in several places.1-3 This work has been mainly concerned with the determination of the chemical diffusivity as a function of composition and temperature. In 1947 Smigelskas and Kirken-dall&apos; showed that zinc and copper diffuse at different rates in face-centered-cubic brass, and since then, a number of efforts have been made to determine the intrinsic diffusivities of zinc and copper in this alloy.1, 5-9 Horne and Mehl8 in particular have recently determined the intrinsic diffusivities as functions of temperature and composition using sandwich-type couples and inert markers. Inman et al." also have determined the intrinsic diffusivities in homogeneous alloys using tracer techniques. When the present work was started, no information of this type was available. Consequently, measurements of the intrinsic diffusivities were made as a function of temperature at a constant composition of 28 atomic pct Zn with vapor-solid diffusion couples where the zinc was diffused into the diffusion couple from the vapor phase. The application of these couples to the study of diffusion in a: brass has been described previously.0,7 The temperature dependence of the intrinsic diffusivities was found to follow the relation D, = A, exp(-Hi/RT) and the values of Hzn, and Hcu, were found to be closely the same. It is emphasized, however, that the chemical dif-fusivity (D = N1D2 + N2D1) is a composite diffusivity and does not necessarily follow this exponential form. It is usually found to do so within experimental error for substitutional alloys because the heats of activation of the intrinsic diffusivities generally are not greatly different.&apos;" Also, at the onset of this work, there was no information available concerning possible unequal diffusion rates of individual components and the existence of a Kirkendall effect in alloys with other than face-centered-cubic structures. Since then, two reports indicating a Kirkendall effect in body-centered-cubic ß brass have appeared. Landergren and Mehl" have published a note describing Kirkendall diffusion experiments with sandwich-type couples. Inman et a1.9 also find a Kirkendall effect in this alloy using the tracer technique. In the present work, several aspects of the Kirkendall effect in ß brass were further investigated using vapor-solid couples. Two different couples were used, one in which the zinc was diffused into the specimen from the vapor phase and the other in which the zinc was diffused out of the specimen into the vapor phase. Briefly, the existence of a Kirkendall effect is confirmed and it is found that Dzn/Dcu = 3 at about the 46 atomic pct composition in this alloy at 600°, 700°, and 800°C. As a result of the unequal diffusion rates of zinc and copper, volume changes occur and subgrain formation is observed in the diffusion zone. In addition, significant porosity is produced by the precipitation of supersaturated vacancies. Diffusion in this alloy is therefore outwardly similar to diffusion in a brass where these effects are also observed, a Brass Experimental Methods—The use of vapor-solid couples in studying diffusion in a brass has been described in previous articles.6,7 The method briefly consists of sealing a copper specimen with Kirkendall markers initially placed on its surface in an evacuated quartz capsule along with a large zinc source of fine a brass chips and then diffusing the zinc into the specimen through the vapor phase. The zinc concentration at the specimen surface rises rapidly enough to a value near that of the a brass source so that the surface concentration may be regarded as constant during diffusion. Under these boundary conditions, values of the chemical diffu-sivity may be obtained by applying the Boltzmann-Matano analysis to the concentration penetration curve, and the intrinsic diffusivities may be obtained from Darken&apos;s5 equations when the velocity of marker movement is known. The diffusion specimens were made from OFHC copper in the form of disks 3.2 cm diam and 0.5 cm thick with faces surface-ground parallel to within +0.001 cm. Markers in the form of fine alumina particles <0.0002 cm diam were placed on the specimen surface. These specimens were then sealed in quartz capsules along with enough a brass chips of a 30.0 atomic pct Zn composition to keep the source concentration from decreasing by more than 0.3 atomic pct Zn as a result of the loss of zinc to the specimen during diffusion. The quartz capsules which were initially evacuated to a pressure of

Jan 1, 1956

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik&apos;s analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated&apos; by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydro-chloric acid and other chemicals has existed and continues.

Jan 7, 1953

COMMITTEE IN CHARGE SPENCER PENROSE, Chairman A. E. CARLTON, Chairman Finance Committee GEORGE M. -TAYLOR, Vice-chairman. J. DAMSON HAWKINS, Secretary DENVER COLORADO SPRINGS Finance Finance T. B. STEARNS A. E. CARLTON RICHARD A. PARKER SPENCER PENROSE T. B. BURBRIDGE GEORGE M. TAYLOR A. L. BLOOMFIELD, Treasurer Arrangement Registration DAVE G. MILLER LOREN C. LENNOX FRANK BULKLEY HORACE F. LUNT GEO. E. COLLINS J. M. TIPPETT Entertainment Arrangement and Entertainment F. H. BOSTWICK GEORGE M. TAYLOR F. E. SHEPARD J. D. HAWKINS HOWLAND BANCROFT A. E. CARLTON B. P. MORSE A. L. BLOOMFIELD J. G. PERRY THOMAS B. CRONE E. P. ARTHUR ETIENNE A. RITTER CRIPPLE CREEK PUEBLO THOMAS B. CRONE J. F. WELBORN E. B. ARTHUR H. B. CARPENTER N. S. GREENSFELDER L. B. EAMES A. E. CARLTON F. ROBINSON B. F. HILL J. G. WILLIS

Jan 8, 1918

By Colin G. Fink, Leslie G. Jenness

Tantalum and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTaz06), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore,becoming (Pe, Mn)O.(Ta, Cb)2Os. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and si1ica. l Methods of Extraction Several methods have been proposed for the extraction of tantalum and columbium from their ores, among them being: 1. Fusion with Potassium or Sodium Bisu1fate.—The finely ground ore is fused with potassium bisulfate, after which the mass is boiled with water and the fusion repeated several times. The residue finally resulting is digested with ammonium sulfide to remove traces of tin and tungsten, boiled with hydrochloric acid, filtered and washed. These oxides are then dissolved in hydrofluoric acid, the silica evolved as silicon tetra-fluoride and the hydrofluoric acid solution used for the potassium double fluoride separation of tantalum. 2. Fusion with Sodium Carbonate and Sodium Nitrate.2—This fusion renders the tantalum and columbium soluble, and they are extracted

Jan 1, 1931

By Albert Sauveur

(Cleveland Meeting, October, 1912.) ALTHOUGH many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel that; is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes martensitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line M0-and it remains martensitic or austenitic after slow (air) cooling.1 We have inn this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening. Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it * Professor of Metallurgy and Metalllography in Harvard University. + Assistant in Metallurgy and Metallography in Harvard University. 1 The boundaries between the various zones are not, as a matter of fact, as sharp as indicated in the diagram, because pearlite is not transformed abruptly and in its entirety into martensite when a certain critical composition is attained, nor is martensite suddenly and completely converted into austenite. Greater refinement in the construction of the diagram would undoubtedly result in the introduction of troosto-pearlitic, troostitic, and troosto-martensitic zones between the pearlitic and martensitic areas and-of a martenso-austenitic zone between the martensitic and austenitic areas. Fur the purpose of this note, however, the existence of these transition-conditions may be ignored.

Nov 1, 1912

By J. R. Kyte, C. C. Mattax

Previous workers have developed differential equations to describe oil displacement by water imbibition, but have not explicitly defined the relationship between recovery behavior for a single reservoir matrix block and its size. In the present work, imbibition theory is extended to show that the time required to recover a given fraction of the oil from a matrix block is proportional to the square of the distance between fractures. Using this relationship, recovery behavior for a large reservoir matrix block is predicted from an imbibition test on a small reservoir core sample. The prediction is then extended to analyze recovery behavior for fractured- matrix, water- drive reservoirs in which imbibition is the dominant oil-producing mechanism. Experimental data are presented to support the basic imbibition theory relating matrix block size, fluid viscosity level and permeability to recovery behavior. INTRODUCTION Imbibition has long been recognized as an important factor in recovering oil from water-wet, fractured-matrix reservoirs subjected to water flood or water drive. l-3 Recently, two approaches have been published which might be used to predict imbibition oil-recovery behavior for reservoir-sized matrix blocks. Graham and Richardson4 used a synthetic model to scale a single element of a fractured-matrix reservoir. lair,&apos; on the other hand, used numerical techniques to solve the differential equations describing imbibition in linear and radial systems. This latter method requires auxiliary experimental data in the form of capillary pressure and relative permeability functions. These two approaches, i.e., synthetic models and numerical techniques, have been used to study a variety of reservoir fluid-flow problems. One pur- pose of this work is to present, with experimental verification, a third method for predicting imbibition oil recovery for large reservoir matrix blocks. This method uses scaled imbibition tests on small reservoir core samples to predict field performance. The imbibition tests are easier to perform than the capillary pressure and relative permeability tests required to apply the numerical method. Furthermore, when suitably preserved reservoir-rock samples are used, the properties of the laboratory system are the same as those of the field. This offers an important advantage over the use of synthetic models because there is usually some question as to how accurately reservoir-rock properties can be duplicated in such models. Based on the recovery behavior for a unit matrix block, an analysis is presented to predict oil recovery for a fractured, water-drive reservoir made up of many such unit blocks. In the analysis, it is assumed that the flow resistance and the volume of the reservoir fracture system are negligible compared with that of the porous matrix. These assumptions are generally consistent with observed characteristics of many fractured-matrix reservoirs, and have been employed in previous studies.2,3,6-8 further assumed that the effect of gravity on flow in the matrix blocks is negligible. On first thought, the latter assumption might appear to seriously limit application of the method. However, in a fractured reservoir, the effect of gravity on flow in a matrix block will be restricted by the height of the block. Furthermore, matrix permeabilities are often very low (10 md or less) in such reservoirs. This means that capillary or imbibition forces will be large, thus tending to minimize the relative importance of gravity. For these reasons, imbibition should be the dominant oil-recovery mechanism in many fractured-matrix, water-drive reservoirs. The predictive method presented in this report is applicable to such reservoirs. SCALING IMBIBITION THEORY The "scaling laws" applicable to the operation.

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948

By John Chapman, J. C. Vaughan

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By J. C. Vaughan, John Chapman

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal&apos; and by Chew and Connally&apos; for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7&apos; API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.&apos; All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By A. H. Daane, J. F. Haefling

BECAUSE of the wide use of platinum in industry and research, the physical properties of this metal, including its vapor pressure, have been studied in some detail.&apos; The other members of the palladium-platinum group of metals have not been studied as extensively, and only qualitative information is available on the vapor pressure of palladium. Data given in literature by Vines1 and Brewer2 on the vapor pressure of palladium are based on the qualitative observations by Holborn and Austin3 and Crookes4 on the rate of volatilization of palladium filaments in various atmospheres. The general observation that palladium is the most volatile metal of the palladium-platinum metal group was corroborated by Bell, Love and Normand who studied the separation of isotopes of the platinum-group metals by a mass spectrometric method. We have measured the vapor pressure of palladium using the Knudsen effusion technique. In this work, the effusion vessel was suspended from a quartz-fiber microbalance into an induction furnace, and the amount of vapor effusing from the vessel was determined by direct weighing of the vessel during the measured heating times. This technique has been described in a report from this laboratory." The vapor pressure of palladium was calculated from these measurements using the equation P...... = 17.14 -W- (77m)&apos;u [1] a t where ? is the weight loss in grams of vapor of molecular weight m from a vessel having an orifice of a sq cm, during t sec. The derivation of this equation from kinetic theory has been described in a previous report from this laboratory: as well as in texts discussing the kinetic theory of gases.%" Test Vessel—In the search for a suitable material for the effusion vessel, it was found that tantalum reacted with palladium metal to form intermetallic compounds, and graphite was readily dissolved in palladium metal to form what appeared to be a liquid phase at a temperature several hundred degrees below the melting point of palladium. On cooling, the graphite gathered into spherical balls in the palladium, with crystals extending radially from the center of these balls, some of which were a millimeter or more in diameter. However, palladium metal vapor did not attack the graphite vessel, so graphite could be used where it did not contact condensed palladium. Tungsten did not appear to react with palladium vapor or molten palladium at its melting point, but it was not convenient to use a tungsten-vapor pressure vessel because of the difficulty of fabricating this metal. Since the vapor-pressure range to be studied (10 2 to 10 &apos; mm) did not appear to extend above the melting point of palladium, a combination of tungsten and graphite served to provide a very satisfactory effusion vessel. The lower half of the graphite vessel was lined with some strips of tungsten foil and the sample of palladium consisting of a coil of sheet was placed in the tungsten liner; in this way, no contamination of the palladium by carbon occurred. Procedure After outgassing at 1500C, the tungsten-lined graphite effusion vessel was loaded with 300 mg of

Jan 1, 1959

By N. J. Grant, B. C. Giessen, U. Wolff

With the aid of the splat-cooling technique of rapid quenching, metastable alloy phases based on antimony ad bismuth have been prepared. At room temperature, simple cubic phases were found in the Sb + Au, 56 + Yd, and Sb + Ni systems. Another phase was retained in the Au-Bi system at -190°C; in this systent, a microcrystalline phase and a rhombohedrally distorted phase were also observed. The crystal chemistry of these phases is discussed in terms of their valence electron concentration range. A remarkable five-step Phase sequence was found upon heating and equilibration of certain metastable Au-Bi alloys. USING the splat- cooling technique of rapid quenching from the liquid,&apos; a large number of metastable intermediate alloy phases have been prepared in recent years. Thus, Hume-Rothery phases of the hexagonal type based on the valence electron concentration have been produced in systems where they are missing in equilibrium, e.g., Ag-Ge 1 or AU-Sb. 3 In a comprehensive study of metastable alloys based on tin, simple hexagonal metastable y phases were found, raising the total of stable and metastable y phases from 3 to 13. 4 In the In-Bi system, five new metastable intermediate phases were retained.&apos; In most cases, the new metastable phases have some crystal chemical characteristics in common: a) They have rather simple, elementlike structures with few atoms per unit cell, e.g., y phase,4&apos;5 or the metastable primitive cubic phases in the Ag-Te and and Au-Te systems.= b) Their structures are often related to those of the terminal phases, or to elements that are straddled in their position in the periodic table by the constituent elements; this is the case for metastable ß (In-Bi) with the structure of white ß Sn,&apos; or metastable a (Cd-sn). 4 c) They seem to represent the crystal structures appropriate to certain average group number (AGN) ranges in which no or few single-phase structures exist in equilibrium. These average group number ranges can probably be equated in the case of many elements of the Ba(Zn)-Bs(As) groups with the averaged valence electron concentration. In the present work, the splat-cooling technique has been applied to the alloys of antimony and bismuth. In equilibrium, neither element forms intermediate alloy phases with other B elements from groups Bl(Cu) to B4(Si) that contain more than 66.7 at. pct of Sb or Bi, respectively, e.g., AUSb 2. 7 Thus, antimony- or bismuth-rich phases, which might be closely related to antimony or bismuth, and which would reflect struc- tural changes occurring on alloying with small amounts of addition elements, do not exist. Also, the terminal solubility of antimony and bismuth for all B metals is very small. It was therefore of interest to investigate the influence of enforced, nonequilibrium solid solution of addition elements in antimony and bismuth on their crystal structures. It was found that additions of group B 2-B4 metals act distinctly differently than additions of group T 10 and B1 metals. The latter set of additives will be treated here. EXPERIMENTAL TECHNIQUES Alloy preparation and splat-quenching followed closely the procedures described in Refs. 1, 4, and 5; they consisted of the preparation of master alloys from high-purity starting materials (99.99+ pct) and blast-atomizing of 20-mg quantities onto copper sheets. The resulting approximately 1 to 5 u thick foils were investigated by X-ray diffraction. The cooling rates obtained are of the order of 107 to 10 8 C per set,&apos;" causing solidification to proceed at a rat; of approximately 100 cm per sec.&apos; Powder patterns of the resulting fine-crystalline materials were taken with filtered CuK, radiation. For antimony alloys the substrates were held at room temperature and for bismuth alloys at -190°C both during splat foil deposition and X-ray investigation. Annealing treatments at several

Jan 1, 1969

By D.E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size. IN order to determine the relative wear rates of several sizes of grinding balls, groups of 4, 31/2, 3, and 2 in. balls were marked individually and were charged, all at the same time, into each of two production mills grinding copper ore. The remainder, and vast majority, of the ball charge consisted of 2 in. diam, and smaller, white, cast iron balls. The original weight of each test ball was determined and recorded. Some of each group of test balls were recovered from the mills periodically, individually reidentified, and reweighed. The test balls were recovered during regular maintenance shutdowns, at approximately thirty-day intervals, so as to avoid disrupting operations. As soon as the weights had been recorded, each marked ball was recharged into the mill from which it had been taken. The test units were mechanically the same and theoretically received equal tonnages of feed. All of the test balls were of forged, alloy steel composition with only slight variations in chemistry that would not be expected to affect the physical properties. All were heat treated in the same manner to produce a high hardness, as equal as possible for all sizes and as uniform as possible from surface to center. Generally speaking, the hardness of the portion worn from the balls during the test ranged from 62 to 65 Rockwell C. The microstructure was, therefore, predominately martensitic. The method of marking the test balls consisted of forming a small, round hole, 3/16 or 1/4 in. diam, into the center of each test ball with a Thomas Metal Master disintegrator, which produces a hole in fully hardened steel without affecting the hardness of the surrounding metal. After the hole was formed, each test ball was individually weighed to the nearest gram and the weight was recorded. The balls were grouped as to size and each group assigned a code letter. The individual balls within the various groups were then assigned a number. A small copper disc was stenciled on one side with the group letter and on the other side with the individual ball number and dropped into the hole in the corresponding test ball. The hole was then plugged with a low-melting-point metal alloy, which could be melted out in boiling water. Half of the test balls in each group were charged into one mill and the other half into another mill, so that all test balls in each mill would be subject to, as nearly as possible, identical conditions for an equal length of time. Previous testing had indicated that the wear rates on balls of different sizes could not be accurately compared if weight loss, or percentage weight loss, were used as a basis for comparison. Fig. 1 is a graphic record of the average weight loss for each size group in mill No. 1, and it becomes readily apparent that the larger balls lose substantially more weight in a given length of time. Fig. 2 is a graphic record of the average percentage weight loss for each size group in mill No. 1, illustrating that the smaller balls definitely lose a greater percentage of their original weight in a given length of time. It was, therefore, decided to convert the actual weights of the test balls to diameter and follow the diameter losses periodically to see if the wear rates

Jan 1, 1951

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size. IN order to determine the relative wear rates of several sizes of grinding balls, groups of 4, 31/2, 3, and 2 in. balls were marked individually and were charged, all at the same time, into each of two production mills grinding copper ore. The remainder, and vast majority, of the ball charge consisted of 2 in. diam, and smaller, white, cast iron balls. The original weight of each test ball was determined and recorded. Some of each group of test balls were recovered from the mills periodically, individually reidentified, and reweighed. The test balls were recovered during regular maintenance shutdowns, at approximately thirty-day intervals, so as to avoid disrupting operations. As soon as the weights had been recorded, each marked ball was recharged into the mill from which it had been taken. The test units were mechanically the same and theoretically received equal tonnages of feed. All of the test balls were of forged, alloy steel composition with only slight variations in chemistry that would not be expected to affect the physical properties. All were heat treated in the same manner to produce a high hardness, as equal as possible for all sizes and as uniform as possible from surface to center. Generally speaking, the hardness of the portion worn from the balls during the test ranged from 62 to 65 Rockwell C. The microstructure was, therefore, predominately martensitic. The method of marking the test balls consisted of forming a small, round hole, 3/16 or 1/4 in. diam, into the center of each test ball with a Thomas Metal Master disintegrator, which produces a hole in fully hardened steel without affecting the hardness of the surrounding metal. After the hole was formed, each test ball was individually weighed to the nearest gram and the weight was recorded. The balls were grouped as to size and each group assigned a code letter. The individual balls within the various groups were then assigned a number. A small copper disc was stenciled on one side with the group letter and on the other side with the individual ball number and dropped into the hole in the corresponding test ball. The hole was then plugged with a low-melting-point metal alloy, which could be melted out in boiling water. Half of the test balls in each group were charged into one mill and the other half into another mill, so that all test balls in each mill would be subject to, as nearly as possible, identical conditions for an equal length of time. Previous testing had indicated that the wear rates on balls of different sizes could not be accurately compared if weight loss, or percentage weight loss, were used as a basis for comparison. Fig. 1 is a graphic record of the average weight loss for each size group in mill No. 1, and it becomes readily apparent that the larger balls lose substantially more weight in a given length of time. Fig. 2 is a graphic record of the average percentage weight loss for each size group in mill No. 1, illustrating that the smaller balls definitely lose a greater percentage of their original weight in a given length of time. It was, therefore, decided to convert the actual weights of the test balls to diameter and follow the diameter losses periodically to see if the wear rates

Jan 1, 1951

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner&apos; us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.&apos; for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi&apos; F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

By F. M. Walters

IN order to isolate the effect of an element on some property of an alloy, the effect of the other alloying elements must be elimi- [ ] nated, either by reducing their quantity to the extent that they may be neglected or by determining the specific effect of each. The success of Grossmann1 in calculating [ ] hardenability from chemical composition by means of factors suggested such a

Jan 1, 1942

By Alan English

INTRODUCTION During the Bicentennial Year in the United States of America, recognition should be given to the fact that 20 years ago the first large-scale commercial pelletizing plant was started and attained rated capacity. This was the beginning of a new industry. Twenty years ago the total production of pellets was principally from pilot plant facilities and totaled in the thousands of tons per year. At the present time the world production is slightly in excess of 280 million tons per year. This truly is a tremendous growth for any industry. Such a production growth obviously is accompanied by a similar growth pattern in the development of process, equipment, and facilities. During the growth and development period, different materials became more adaptable for processing. For example, initially the pelletizing of iron ores revolved around the magnetite concentrates where the heat of reaction constituted a very important part of the process fuel. During this growth period, specular hematite, earthy hematite, mixtures of hematite and magnetite, and even non-ferrous type materials were pelletized, a function previously thought not practical. The demand for the use of pellets has also broadened their concepts. At first they were made to replace the high-grade iron ores used in blast furnaces. Nowadays, not only have they replaced iron units, but they have had a major influence on the design of larger blast furnaces and have contributed to production rates in excess of 10 000 tons per day from a single furnace. They have also been used in the manufacture of steel, principally for coolants in the BOF practice. More recently, with the improved beneficiation techniques that have been developed over the same period of time, pellets have been used for the direct reduction process and can be used directly

Jan 1, 1977