Search Documents

By R. D. Coleman, A. E. McIlhinney, C. E. Capes

tentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product.1 Fine Coal Treatment Processes Most coal cleaning methods depend upon the density difference between coal and its impurities to effect separation. These gravity concentration methods, however, are not practical for particles finer than about 100 mesh and cleaning methods dependent upon the differences in

Jan 1, 1971

By Manuel Valerio Ortega

This Mexican amalgamation-process, invented in 1557, at Pachuca, by Bartolome de Medina, has been widely discussed in America and Europe, but thus far there is no universal agreement as to all the chemical reactions involved. Having been, after many trials, the first to succeed in effecting the amalgamation of silver-ores by the same mechanical means, but doing without one of the chemical substances which had been considered indispensable in the practice of 300 Sears, I am led to offer these notes as a contribution to the discovery of an exact theory concerning the patio process. My treatment for silver- and gold-ores being protected by letters-patent in this country, the United States, France, Peru, Bolivia and Chile, I may speak freely concerning its materials and manipulation. I. Patio-Amalgamation. The ore extracted from the mine is sorted by pepenadores, who break the large pieces with hammers, rejecting those which contain no ore, set aside the very rich to be smelted, and deliver the rest to be crushed and pulverized for direct amalgamation in the patio. The broken lumps, of about fist-size, are first ground in Chilean mills, and then reduced, in arrastras or tahonas, to fine slime. After the lama or slime has acquired a suitable consistency by the evaporation, through the sun's heat, of a part of the water which it contained, it is spread upon the patio or amalgamating-floor, where it is mixed with 5 or 6 per cent. of common salt. The next day a certain amount (depending upon

Jan 1, 1902

By R. Steinitz, L. Seigle, R. Resnick

THE rates of growth of the carbide phases MC and M2C in the Ta-C and Cb-C systems have been measured at various temperatures and the results used to estimate the rate of carbon diffusion within the inter metallic phases. Sheets of high-purity tantalum (50 ppm Cb, <25 ppm Ti, 10 ppm Fe, 5 ppm Cr, <50 ppm Mo, W, and all other metals, 15-75 ppm O2, 10-30 ppm N2, and 10-30 ppm C) approximately 1/4 by 1/2 by 0.020 in. were heated to temperatures between 1800" and 2700°C in a carbon resistor furnace under an atmosphere of argon plus sufficient methane to maintain an excess of carbon at the sample surface. The thicknesses of the carbide layers, illustrated in Fig. 1, were measured with a filar micrometer and plotted logarithmically as a function of time. Fig. 2 is a typical plot for the TaC phase. The points may be represented within experimental error by lines with slope equal to 1/2; therefore the growth of the layers may be described by the usual expression X = kt1/2, where X is the layer thickness, t is the time, and k is a temperature-dependent constant. From these data and compositions at the phase boundaries, it is possible to estimate values for the diffusion coefficients of carbon in each phase, assuming that layer growth occurs by carbon diffusion alone, and that the dif-fusivity is not a function of composition within each

Jan 1, 1965

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO&apos; afe aFeO &apos; aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K&apos;. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO&apos; afe aFeO &apos; aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K&apos;. Making these changes, 7

Jan 1, 1942

THE problem of reaction rates in the open-hearth process is essentially that of trying to form a fairly clear picture of the "chemical mechanisms" in the bath. Quantitative data on reaction rates would perhaps not be of much practical importance even if they were available; however, what few approximate data there are can be used in combination with data given in Chapters 16 and 17 to sketch a picture of the "chemical mechanics" of the open-hearth process that is consistent with essentially all the present available evidence. The result may later be found incorrect in many details but even so it will illustrate certain useful methods for obtaining a clearer understanding of the process. Consistent with the treatment in Chapter 15, but in simpler terms, we may say that chemical reactions in general involve the following elements or steps: 1. The reacting molecules are mixed together in space in such fashion as to favor collisions among them. 2. Units of what is usually an intermediate molecular arrangement called an activated complex are formed at a certain rate, depending on temperature and concentrations. 3. These activated complex units decompose into the reaction products (this step usually assumed to be so rapid as never to limit the over-all process). 4. In any of these steps, heat energy may have to flow into, or away from, the reaction zone to permit the reaction to proceed. 5. The products of reaction will usually have to move out of the way to permit further reaction. The temperature factor enters mainly through step 2, and its effect is very marked. (What is called temperature is really the mean energy content of all the molecules of the substance involved; at any one temperature a certain proportion of the moleculea will have much higher energy content than the mean value.) Various reaction rates measured at around room tem-

Jan 1, 1951

By J. B. Hiskey

The hydrometallurgical application of thiourea in processing precious metal ores and concentrates has reached the development stage. This paper reviews recent technical literature covering the process development of thiourea leaching. In addition, recent fundamental contributions are discussed. Most of the interest in thiourea leaching has involved treating high grade concentrates that have sufficient value to just the use of thiourea as a reagent. An important development in thiourea technology is the addition of SO2 to the leaching solution. This procedure effectively reduces the decomposition of thiourea and eliminates the problems of passive surface layers that limit the leaching efficiency. Results for the thiourea leaching of a bulk sulfide concentrate and a residue from the autoclave leaching of a smelter flue dust are also reported. As determined by a standard bottle roll cyanidation test, the bulk concentrate was extremely resistive to cyanide leaching yielding only 16% gold and 2% silver extraction in 24 hours. Leaching with a relatively concentrated thiourea solution (1MCS (NH2)2) resulted in 83% gold and 75% silver extraction in four hours. With the treated flue dust residue, gold extraction was about 60%. Gold and silver extraction with cyanide was sensitive to both cyanide concentration and oxidizing conditions. Cyanidation resulted in 59% gold extraction and 77% silver extraction in 24 hours.

Jan 1, 1985

By R. J. Wasilewski

The variation of elastic modulus with terrzperature between -150° and 600°C has been investigated. Compounds close to equiatomic cornposition exhibit very low modulus values and very high damping near room temperature. The modulus rises steeply with both decreasing and increasing temperature. The modulus minimum and the high damping are believed to be connected with a martensitic transformation of TiNi. In bulk material this transition takes place slightly above room temperature quite rapidly and reversibly, with a hysteresis of some 30°C, depending on the Ti:Ni ratio. Oxygen impurity affects the reaction time. THE inter metallic compound TiNi has been reported to exist in an ordered CsCl (B2) structure,l-6 the homogeneity range varying rather markedly with temperature.7 Some investigators reported this compound to decompose peritectoidally to Ti2Ni and TiNi, between 650° and 800°C,3 or below,&apos;,g the latter workers also suggesting the decomposition to be strain-sensitive. Purdy and Parr were the first to report a structural transformation to a new, possibly hexagonal, structure at 36°C,7 a temperature indubitably too low to allow the significant amount of diffusion necessary for a peritectoid reaction. Mechanical-property investigations of compositions close to TiNi just above room temperature have qualitatively shown remarkable anomalies, particularly with respect to clamping,&apos; and to a "memory" effect, that is, plastically deformed material returning to its original shape on being heated through the "decomposition" temperature.9 The original explanation of this effect—based on the apparent experimental observation of Ti2Ni or TiNi, formation in the material subjected to tensile or compressive stresses, respectivelp—does not appear plausible. It appeared more probable that the change involved may be a martensitic, diffusionless structural transformation, similar to those observed in other B2 structures such as 0 brass,&apos;&apos; AuCd,ll and AuZn.12 The existence of such transformation has been established recently,&apos;, although the symmetry of the low-temperature structure is not yet known. The present paper describes the elastic modulus and damping behavior of polycrystalline TiNi in both structures. EXPERIMENTAL METHOD 1) Specimens. All the specimens to be investigated were prepared from premelted electrolytic nickel and iodide titanium by nonconsumable arc melting and casting in a water-cooled copper mold. The cast billets were canned in mild steel, extruded, and swaged to approximately 0.375 in. diam. The cans were then removed by pickling or machining. Preliminary material balance checks indicated no significant weight losses on melting (less than 5 mg on a 50-g button); hence nominal compositions have been used throughout. In agreement with previously reported observations7 no single-phase material was obtained at—or close to—Ti 1.00 Ni1.00 a small amount of finely divided second phase always being present. It was found that most of the oxygen impurity was associated with this minor phase, which was identified as oxygen-bearing Ti2Ni—possibly Ti,Ni,O. The amount of this phase—at any given Ti:Ni composi-

Jan 1, 1965

By H. Scott

Since Bohler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar 3-2-1 obtained by increasing the maximum temperature to which the material was heated, much has been published1 connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The significant facts established by recent investigators2 are: that when the transformation occurs at the higher temperature Ar1, troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar&apos; and Ar" adopted here is that of Portevin. Previous Investigations Reviewing the work on this subject published in a recent issue of Revue de Metallurgie and referring in particular to his statement that martensite is a solution of carbide in alpha iron, Le Chatelier says :4 "How then can a theory already 20 years old demand new investigations? The reason for it is that we have not succeeded in proving directly the real presence of the transformation of iron during the very short duration of the quenching. The fall of temperature takes place at the rate of several hundred degrees per second and the observation of

Jan 1, 1920

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regard-ing the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing tempera-tures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for-the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by O. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence .of a wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity clue to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

By F. M. Yans, A. D. Donaldson, A. R. Kaufmann

Beryllium was mixed by powder. metallurgical techniques with copper, nickel, iron, and chromium, respectively, to form beryllium -rich binary alloys which Mere then extyuded and rolled transtverse to the extrusion direction. The effect of each alloying element was determined by tensile testing. In solid solution, small amounts of iron and nickel had an embrittling effect, while copper in solution increased the strength but had no effect on ductility. The effect of chromium was complicated and not readily explainable. Observations concerning the planes and modes of fracture were made. BERYLLIUM possesses some very attractive properties for general design applications, especially its strength to weight ratio which is approximately twice that of aluminum and three times that of stainless steel. Equally significant, however, is its combination of high moduli , high strength (approximately 70,000 psi tension and 40,000 psi shear), and low density (0.0658 Ib per in.3), which has made it a potentially important structural material for use in high-speed aircraft and missiles. The main attractions of beryllium are most marked when compared to other constructional alloys now in use. For example, while its density is approximateiy that of magnesium, its modulus of elasticity is approximately seven times that of magnesium, three times that of titanium, four times that of aluminum, and 1 1/3 times that of steel. Furthermore, its relatively high strength and high melting temperature permit design for service temperatures to about 1100°F. It is felt by the aircraft industry in general,&apos; that the high cost of beryllium can easily be amortized by the savings in fuel costs, and increases in aircraft payload and range. The only factor which has prevented the use of the metal in structural applications is its lack of sufficient ductility. It is this property that has retarded the development and utilization of beryllium. Beryllium&apos;s modes of deformation, Fig. 1 indicate that the main fracture planes at room temperature in a randomly oriented sample are the (0001) basal planes; the (1150) prism planes are the planes of secondary fracture.&apos; Klein, Macres, Woodard, and Greenspan3 obtained elongations of up to 40 pct in beryllium sheet rolled above 700°C when the (0001) basal planes were oriented parallel to the plane of the sheet (see Fig. 2).

Jan 1, 1962

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

S. F. EMMONS RESEARCH FELLOWSHIP. The movement was started by a number of the friends and admirers of the late S. F. Emmons, Economic Geologist of the United States Geological Survey, to perpetuate his name through a fellowship to be known as the " S. F. Emmons Research Fellowship," and they have succeeded in raising some $13,000 for the purpose of carrying on research work in economic geology. The Committee in charge of this Memorial Fund has succeeded in obtaining the co-operation of Professors Kemp, of Columbia, Irving, of Yale, and Lindgren, of Massachusetts Institute of Technology, in the administration of this fellowship. These three gentlemen are respectively geologists of the institutions mentioned and are exceptionally qualified to determine in what direction the fund can be best administered. It is hoped that additional contributions will be forthcoming from many who have heard of this movement. Subscriptions are invited and may be sent to any one of these gentlemen, or to Benjamin B. Lawrence, Treasurer, No. 60 Wall Street, New York City.

Jan 11, 1913

S. F. EMMONS RESEARCH FELLOWSHIP. The movement was started by a number of the friends and admirers of the late S. F. Emmons, Economic Geologist of the United States Geological Survey, to perpetuate his name through a fellowship to be known as the ?S. F. Emmons Research Fellowship," and they have succeeded in raising some $13,000 for the purpose of carrying on research work in economic geology. The Committee in charge of this Memorial Fund has succeeded in obtaining the co-operation of Professors Kemp, of Columbia, Irving, of Yale, and Lindgren, of Massachusetts Institute of Technology, in the administration of this fellowship. These three gentlemen are respectively geologists of the institutions mentioned and are exceptionally qualified to determine in what direction the fund can be best administered. It is hoped that additional contributions will be forthcoming from many who have heard of this movement. Subscriptions are invited and may be sent to any one of these gentlemen, or to Benjamin B. Lawrence, Treasurer, No. 60 Wall Street, New York City.

Jan 10, 1913

By E. J. Haug, M. M. Fine

For several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published. Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 4, 1955

By J. E. Burke

RECENT investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen, Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: [D=Ktn [11] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Walker4 finds that, in alpha brass, the rate of growth falls off more rapidly than indicated by Eq I after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker&apos;s data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: [t, Hr i &apos;_ III t„ = R \T, - ~) [2]] where t1 and t2 are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck.&apos; The results obtained by Beck, Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and Hu6 later demonstrated experimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,10 Making implicit use of this assumption, several authors14,15 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parker&apos; have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary, are on the average more surrounded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1948

By F. A. Schaufelberger

METAL can be recovered from a leach solution either indirectly by precipitation as a compound that is later reduced or directly by electrolysis, cementation, or chemical reduction, for example, with hydrogen. The widely used electrowinning processes suffer from the inefficiency of converting fuel to low voltage dc and from low current efficiency when complete recovery is attempted. With the batch hydrogen reduction methods outlined here, a unit of fuel converted to hydrogen in modern gas reform plants will make two to three times as much metal as can be obtained with electrolysis. With continuous hydrogen reduction, four to six times as much metal is obtained. Precipitation by reducing a metal salt solution with H, has been known for almost 100 years.&apos; Commercial use of the process, however, awaited the research and development program initiated by Chemical Construction Corp. Within the last few years this program has brought about construction of commercial plants, listed on page 545. Ideal hydrogen reduction will precipitate a pure metal from a solution obtained by commercial leaching methods at a rapid rate without excessive temperatures and pressures. The metal precipitate will be of desired size and density, less than a percent left in the vessel being deposited on the wetted parts. The present discussion will outline Chemical Construction Corp.&apos;s early development program and will discuss the chemistry and mechanics of reducing copper, nickel, cobalt, and cadmium from solution by H2. Work on selective reduction of nickel from cobalt has been described earlier.&apos; The article is not concerned with precipitation of copper by disproportionation of cuprous solutions where yield is limited3 to 50 pet.* It does not discuss use of gaseous reducing agents other than hydrogen, such as SO2,4 which may lead to contamination with sulfur, or C0,5 which is considerably more expensive than hydrogen and produces a gaseous reaction product, CO2.† The article does not include use of other nongaseous reducing agents,7 which are far more expensive than CO. Also, notes on the history, engineering design, and performance of commercial plants have been given elsewhere.&apos; It will be shown that a pure metal can be precipitated by reduction with hydrogen from solutions obtained by commercial leaching methods when the solution composition is controlled and proper acidity, proper metal ion concentration through controlled complex formation and hydrolysis, and adequate agitation for suspension of metal and for transfer of reducing gas are maintained. Reasonable temperatures and pressures are used which are less excessive than those used by previous workers, although they are maintained at above equilibrium values because of process kinetics.&apos; It has also been found necessary to induce nuclea-tion and to control growth and agglomeration in order to get a powder product of suitable physical properties. Review of the Literature Muller, Schlecht, and Schubardt of I. G. Farben10 claimed a successive reduction of silver, copper, nickel, cobalt, and zinc from ammoniacal solution by applying progressively higher temperatures and hydrogen pressures. Metals produced by this technique were not pure, since no attempt was made to adjust the solution composition between the different reductions. It is doubtful that the zinc product contained any metallic zinc. The major contribution to the literature" was made by the Ipatiews,12 who prepared platinum, iridium, copper, nickel, cobalt, lead, tin, arsenic, antimony, and bismuth at often extreme conditions, up to the critical temperature of water (373ºC), at 1500 to 7500 psi, for as long as several days. Even cadmium and zinc were claimed to have been observed in trace quantities precipitated together with basic salts. In the early experiments solutions were not stirred. Extensive formation of oxides and basic salts occurred, probably long before sufficient hydrogen could be supplied in the unstirred liquid to decrease the metal concentration in solution by reduction. The importance of hydrogen pressure was

Jan 1, 1957

The following outline has been prepared by request with the help of leading professors, business men, and social workers. It is arranged to cover 64 or preferably 96 class periods-four to eight month&apos;s work at the rate of two or three periods a week. More time would be desirable, but less time would be better than nothing. Certain topics must be omitted, especially if the assigned number of periods are lessened, where time is lacking. Many subjects are suggested in order to permit of choice and adaptation to local conditions; this is merely a suggestive outline. The course should be supplemented y engineering trips to study certain industrial conditions and the betterment work of selected companies-and social agencies. It should also be accompanied by brief surveys and practical service by students along the lines indicated. Reports and essays should be written. This is not a regular course in sociology and economics. It is a course in "human engineering" and should probably be directed by an engineering professor of large practical experience. Other members of the faculty, sociologists, economists, selected engineers, employers, labor leaders or others may be requested to lead certain periods, as desired. Care has been taken to avoid biased judgment in selection of topics and references.* * The authors of this outline have compiled an exhaustive list of references to books and periodicals relating to each group of topics. Lack of space prevents the publication of these lists in the BULLETIN, but they will gladly be supplied on request.-Ed.

Jan 12, 1917

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935