Search Documents

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By R. E. Head

Under existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes. Surface Contamination The experience gained by microscopic study of numerous gold ores and tailings has shown that there are pronounced differences in the physical characteristics of the minerals composing them, more especially of the gold. Repeated studies of tailings from flotation and cyanidation of gold ores has established the fact that surface contaminations on gold particles are often directly responsible for high gold losses; comparison of gold particles isolated from flotation concentrates and the resulting tailings have showed that the clean gold has been recovered and the tarnished or contaminated gold invariably lost in the tailing. Obviously, it is not possible to make such a comparison of gold ores treated by cyanidation, as the clean gold has been taken into solution; but when the gold found in cyanide tailing has a tarnished or coated surface, one may infer, with a reasonable degree of certainty, that the clean gold has been extracted. This premise is supported by experimental evidence obtained by isolating particles of tarnished gold and exposing them to cyanide solution in small parting cups. In one such experiment, tarnished gold particles picked from a cyanide tailing showed but slight evidence 01 dissolving at the end of 27 days. In this test, a cyanide solution of 1.6 11). per ton was used and the leach solution was decanted arid renewed every

Jan 1, 1939

By W. D. Bennett

AN interesting effect has been observed in the vacuum etching of titanium in the high temperature ß phase. Using a high vacuum annealing furnace, operating at less than 2x10-6 mm with a tubular titanium liner, it has been found possible to etch polished metallographic specimens at different temperatures between room temperature and 1000°C without contamination or increase in hardness.' Heat etching of titanium has been reported by other workers,' but the following example is of interest as an experiment under high vacuum in the absence of any contamination. Two polished specimens of iodide-processed titanium are placed at different positions along the axis of the furnace corresponding to temperatures of 900" and 800°C above and below the a-ß transus. The specimens are then raised to these temperatures and annealed simultaneously for 3 hr under the same high vacuum conditions. After cooling and withdrawing the specimens, their surfaces are photographed without further treatment. Figs. 1 and 2 show the results for the 800" and 900°C specimens, respectively. Fig. 1, corresponding to a vacuum etch in the a region, shows a typical equiaxed structure with what appears to be a slight shift of grain boundaries. Fig. 2, corresponding to a vacuum etch in the ß region, shows an equiaxed type of structure with the growth of striations in certain grains. The striations are only superficial, as a light polish and chemical etch restores the clean equiaxed structure. The vacuum etch, occurring as it does above the a-ß transus, records the state of the metal in the ß phase by means of the surface relief produced by the selective evaporation of metal from different grains; the metal itself reverts to the equiaxed a on cooling. The nature of the ß etch" (Fig. 2) suggests that, in transforming from the close-packed-hexagonal a to the body-centered-cubic ß lenticular-shaped laminae are formed parallel to common planes of the two structures. This would explain why some grains appear to be unaffected by the etch. The technique has interesting possibilities in the investigation of the mechanics of high temperature transformation. Acknowledgment This note is published by permission of the Deputy Minister, Dept. of Mines and Technical Surveys, Ottawa, Ont., Canada.

Jan 1, 1956

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By Anthony F. Lucas

Certain geological indications at Glady&apos;s station, four miles south of Beaumont, on the Sabine and East Texas railway (a branch of the Southern Pacific) induced me to undertake a thorough test of that locality by means of a well. I had been making reconnoissances for nearly two years in that part of Texas, before deciding upon this supreme effort. Three previous attempts had been made in the same place: one in 1894 by Messrs. Sharp & Co.; one in 1896 by Mr. J. Looney; and one in 1898 by Messrs. Savage Bros. They had all failed to pass though the immense thickness (500 ft.) of quicksand which underlies the surface soil, clay, etc. At first, I employed the system of boring which I had previously used in the Louisiana salt-deposits.* But I soon found that this method was inadequate, without modification, to deal with the quicksand. Accordingly, I adopted the use of large and heavy castings, and pipes of 12, 10, 8, 6 and 4 in. diameter, successively telescoped one into the other. Boring was begun by Messrs. Hamill Bros., of Corsicana, contractors, about the middle of October, 1900; and on January 10,1901, after many difficulties, a layer of rock containing marine shells was reached, at the depth of 1160 ft. For 150 ft. immediately above, the drill had passed through layers of sandstone and concretions of limestone. At this time there was about 600 ft. of 4-in. pipe, weighing at least 6 tons, in the well; and this, together with the next (6-in.) casing above, was filled with water. When the rock was penetrated the well " blew out," lifting the whole of the 4in. pipe. Mr. Hamill was on the top of the 60-ft. derrick when

Jan 1, 1902

By W. H. Bassett

IN their paper on the directional properties in cold-rolled and annealed commercial bronze,1 Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45° ears" and "90° ears. " Fig. 1 shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45° ears, while that annealed at 950° C. showed FIG. 1.-CUPRONICKEL, 0.032-in. GAGE, CAST WITH MAGNESIUM. ANNEALED AT TEMPERATURES INDICATED (DEGREES CENTIGRADE) AND CUPPED. long "90° ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be.

Jan 1, 1932

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle&apos; and in particular for the special case under consideration.1&apos;2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43&apos;, 55° 16&apos;, 64 3 43 1, and32"26&apos;. These add up to 1802 08 1, indicating a cumulative error of 8&apos;. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43&apos;, 55°16&apos;), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By D. Kunstelj, M. Stubicar, A. Tonejc, A. Bonefacic

A. Bonefafcic, D. Kunsfeli, M. Stubicar, and A. Tonejc The present communication is concerned with the variation of the texture in aluminum wires with die angle and temperature, at constant speed of extrusion. Experiments were carried out concurrently on refined samples, with a stated purity of 99.997 pct pure A1 and commercial samples of 99.5 pct Al. Ingots of refined aluminum samples were machined to 30-mm-diam by 150-mm-long billets. These billets were transformed to 5-mm-diam wires by drawing. The final form, suitable for examination, was obtained by extrusion through conical-face dies with a 1-mm hole diam and extrusion ratio 5:l in diam. The initial form of the commercial aluminum samples was drawn wire 5 mm in diam. These samples showed a poorly defined texture with (111) as a major and (001) as a minor component. A similar defined texture appeared in the refined aluminum samples after drawing to 5 mm diam. Conical-face dies with different angles (defined by the axis and the generating line of the cone) were used in our experiments. The values of the angles were 27, 35, 45, 57, 63, and 90 deg. The extrusion container was fitted with a heating element and controller permitting temperatures up to 600°C to be maintained within i5"C. Extrusion was performed at 250°, 300°, 350°, 400°, and 500°C at constant speed (approximately 1 mm per sec) and constant die reduction. The extrusion product was a wire 1 mm in diam and approximately 20 cm long. In order to remove the surface layer with the "conical" texture and to reduce the absorption by the X-ray examination of the samples, the extruded wire was etched to 0.22 mm in diam. Experiments were performed in the middle sections of the 20-cm-long wires. In addition to the die of l-mm hole diam, dies with a 1.5-, 0.7-, 0.6-, 0.5-, and 0.4-mm hole diam and 63-deg die angle were constructed. In our experiments we did not find in these ranges any important difference concerning the texture of the extruded wires and we continued our work solely on the 1.0-mm die. The diffracted X-rays (Cu K radiation) were recorded photographically. Diffracted intensities were measured on the (111) reflection with a microphotometer. The relative amounts of texture components were determined from the areas under the diffracted maxima. We found the texture of extruded aluminum wires to be strongly influenced not only by the temperature of extrusion and the purity of the sample but also by the form of the die. It is generally admitted that cold-drawn aluminum wires have mainly a (111) texture with a small amount of (001) component, Table I of Ref. 1. In our experiments with wires extruded in conditions represented by Fig. 1, in some cases a single (001) texture was obtained. If these wires were drawn repeatedly at room temperature, X-ray measurements revealed a duplex (001)-(111) fiber texture. Further drawings increased the (111) and decreased the (001) texture component. In Fig. 1 the percentage of material oriented with (001) parallel to the extrusion direction is represented as a function of the temperature and the die angle (a), for commercial and refined aluminum samples, respectively. From these diagrams we may draw the following conclusions. The slope of the die (a) influenced more strongly the texture at the lower rather than the higher temperatures. Again, a stronger influence was found in the case of the commercial in comparison with refined aluminum samples. In the case of the commercial aluminum samples the amount of material with (001) texture increases with increasing wire temperature in an approximately linear manner. This effect is less pronounced in the pure aluminum samples, with the exception of the die with a = 45 deg. In this case the (001) texture decreases with increasing temperature, as shown in Fig. 1. Component (001) is more pronounced in higher-purity aluminum samples. Our experiments led to the conclusion that both (001) and (111) components are essentially stable in extruded aluminum wires. As we obtained a single (001) texture starting with a sample of drawn wire in which the (001) component was very weak, our experiments revealed that the (001) component is not a remnant of the initial texture; this is in disagreement with the findings of Vandermeer and McHargue.1 We gratefully acknowledge discussions with Professor M. Paic. 1 R. A. Vandermeer and C. J. McHargue: Trans. 7MS-AME, 1964, vol. 230, p. 667.

Jan 1, 1969

By D. E. Swets, R. C. Frank

It is well known that hydrogen is introduced into iron or steel as a result of many chemical processes (acid pickling, electrolytic cleaning, plating, etc.). One of the reactions that has been of recent interest1 is the reaction between an iron surface and water vapor. It was shown a few years ago2-4 that hydrogen can be introduced into steel at an accelerated rate during abrasion as a result of this reaction. Grun-berg and Scott have also observed that water in mineral oil lubricants increases pitting failure in ball bearings5 and they have suggested that hydrogen from the water is the primary cause of this effect.&apos; In this laboratory, the question was raised as to whether or not hydrogen is also introduced into the metal surface of a bearing as a result of the decomposition of the hydrocarbon lubricant itself, and an experiment was performed to try to find a satisfactory answer. All steel parts contain some residual hydrogen. Therefore, it appeared that the best way to carry out this experiment without the need for highly accurate quantitative analyses was to use deuterium as a tracer. The natural abundance of deuterium in H2 is only 0.015 pct. The tracer was obtained in the form of deuteroparaffin (CD,(CDJ, CD,) and 0.25 g were dissolved in 20 cc of mineral oil to form the lubricant to be used in the tests. The bearings used were New Departure Type QOLOO ball bearings with a ball diam of 0.187 in. Prior to adding the mineral oil-deuteroparaffin lubricant, the bearings were cleaned in warm trichloroethylene to remove the packing grease. After packing with the new deuterated lubricant, the bearings were operated in a bearing fatigue test machine under a radial load of 190 lb and a thrust load of 190 lb at a speed of 3800 rpm. The expected life under these conditions is about 500 hr. Two tests were made; one for a period of 27 hr and the other for a period of 102 hr. The bearings achieved a temperature of 120o F during the tests. When the tests were stopped the balls were mechanically removed from the bearings and were immediately placed in liquid nitrogen to reduce degassing until the analysis for deuterium could be made. Before analyzing, the balls were warmed to room temperature and scrubbed with several degreasing agents to remove all traces of the deuteroparaffin mixture. This cleaning procedure was shown to be satisfactory by running a control test in which one ball bearing was subjected to all parts of the test except running in the fatigue machine. The hydrogen and deuterium were removed from the balls using a hot extraction apparatus attached to a mass spectrometer. Four balls from each bearing were analyzed. Each one was analyzed separately by removing it from a cold storage volume of the hot extraction apparatus and transferring it to the oven tube with a magnet. As the gases were evolved they were analyzed with the mass spectrometer. Since the hydrogen and deuterium pass through steel in the atomic form and since there are many more hydrogen atoms than deuterium atoms in the sample, the probability of forming an HD molecule is greater than forming a D2 molecule. For this reason the evolution of HD and H was followed as each ball was placed in the oven. The results showed that as each ball from the test bearing was dropped into the oven, the mass spectrometer recording of the HD evolution increased by about ten divisions. When balls from the control test bearing were dropped into the oven, the increase was about one division or less. The hydrocarbon background in the mass spectrometer was also monitored to see if hydrocarbons or deuterocarbons were given off when the balls were dropped into the oven, but no change in the hydrocarbon peaks was observed. Since the balls contained a fair amount of residual hydrogen, isotope ratio measurements were made on the gas obtained from each ball. The D/H value found for those balls which had been operated in the fatigue testing machine was consistently about 0.3

Jan 1, 1962

By David Cornell

Back pressure test data on natural gas wells are short time test data of unsteady state nature. Performance curves from which unsteady state effects have been eliminated, called stabilized performance curves, are necessary for understanding the behavior of gas wells and for scheduling gas fields for periods up to 20 years. A calculation procedure has been developed whereby three day, seven day, 30 day, or other duration stabilized performance curves may be calculated from back pressure test data. Such curves are essential for correct gas deliverability calculations and gas field scheduling. I NTRODUCTION The manner in which a back pressure test is made will affect the slope of the back pressure curve because the radius of drainage changes with the length of time that the well is allowed to flow. The reciprocal of the slope of the back pressure curve is defined as n in Equation 1 and varies from 0.5 to 1.0. If the flow is viscous and the radius of drainage constant, n will have a value of 1.0. Because of turbulence in the formation near the wellbore, the pressure drop is usually greater than the viscous flow pressure drop and the exponent n is frequently less than 1.0. In addition, since the radius of drainage moves away from the well-bore during the test, the gas flows a greater and greater distance as the test proceeds, with a resulting increased pressure drop at the high flow rates, and, again, n for the test tends to be less than 1.O. The effect of the changes in the radius of drainage may be calculated and the results used in preparing stabilized performance curves for fixed values of the radius of drainage. Such curves can be made for a defi- nite time period, such as three day, seven day, or 30 day stabilized performance curves. These cukes will show the effect of turbulence near the wellbore and can be used to predict the performance of the gas well at any flow rate or for any production period. In order to discuss the importance of the radius of drainage quantitatively, it should be defined. Muskat" defines the radius of drainage as follows: "... the radius of drainage gives the distance from the well to which the approximately steady state condition has been established ... it being assumed that no gas is removed from any point until the radius of drainage has passed that uoint." An eauivalent definition of the radius of drainage is that radius at which the extrapolated portion of the steady state portion of the pressure gradient gives a pressure equal to the shut-in reservoir pressure. This definition is also implied in the back pressure equation. The radius of drainage is, then, the distance into the reservoir from which the gas appears to originate at any time. It is, however, only a useful concept and does not actually exist. Fig. 1 illustrates the definition of the radius of drainage. At the end of each flow period the radius of drainage may depend on three factors: (1) the duration of each flow period; (2) the rate of gas production; and (3) the rate and duration of the previous flow periods. In general, back pressure tests are conducted with various lengths of production time and at various flow rates. Each individual back pressure test, therefore, requires an individual analysis. The calculations of the change in the radius of drainage have been made, however, for the case of equal flow periods for all four production rates and several sets of increasing flow rates. Fig. 2 illustrates the results of such calculations made by the method of Cornell and Katz2 for the case of 8, = 50,000 and the flow rate increasing in the ratio 1.0:2.0:3.0:4.0 for each flow period. The increase in the radius of drainage during the test is apparent.

Jan 1, 1956

By Clarence W. Balke

SMALL buttons of fused tantalum have been produced by arc fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author&apos;s experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author&apos;s opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By S. W. Parr

THE low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700° or 800° C. For convenience in this discussion, the single number 750° will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750°, there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750°, there is substantially no secondary decomposition; above 750°, the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750°. Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition, of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement

Jan 2, 1920

By Alexander Field

The hot-rolling properties of a series of high-sulfur steels are described. From a consideration of the sulfur, manganese, and zirconium contents of these steels, it is shown that zirconium reacts with the sulfur content of molten steel in accordance with the equation Zr + 2S = ZrS2. Zirconium disulfide appears in the finished state as gray-colored inclusions, similar to manganese sulfide in plastic behavior and general appearance. Zirconium completes its act of deoxidation before proceeding to combine with sulfur and indirectly increases the effective sulfur-combining power of any manganese which may be present. IN A previous paper,1 the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of "red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the reaction between zirconium and sulfur in molten steel may he represented by the simple equation, Zr + 2S = ZrS2, and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion.

Jan 2, 1924

By BERNARD PLANNER

PRODUCTION COSTS, profits, and quality are the primary factors in the peacetime production of iron and steel. In a war emergency, as high production rates and as complete utilization of readily available raw materials as possible, consistent with securing passable quality, become the most important factors. In this connection a discussion of some of the recent developments in the German iron and steel industry, where the problem of scarcity has naturally always been more acute than in the U.S.A., maybe of interest. To get more pig iron out of the existing blast furnaces it was necessary to obtain the maximum efficiency from the iron-bearing raw materials. This was achieved by eliminating all "excess baggage," chiefly by beneficiating the ore. The preparatory work for this was done by various methods which are effective when the ore either is too poor or contains too many impurities or too much gangue. Some of the beneficiation methods are well known, some are combinations of wet-mechanical, magnetic, roasting, sintering, and other treatments.

Jan 1, 1942

By Albert Brokaw

THE so-called ?paraffin dirt" of the Gulf Coast oil fields has been con¬sidered an indication of the possible presence of oil and gas, and not a few wells have been brought in solely on the basis of such evidence. In a sense, it may be empirically justified as evidence of the presence of oil or gas, though it cannot be said to be infallible. If the writer is correctly informed, its association with oil and gas was pointed out by Lee Hager some years ago, and while it is commonly mentioned by geologists and operators in conversation, no discussion seems to have found its way into print. The present interpretation is based on laboratory study rather than on field investigation, and is put forth with the hope of stimulating discussion which shall lead to more complete understanding. The term "paraffin dirt" has been applied to soils with a peculiar texture, which has been described&apos; as "curdy" or "rubbery." When moist, the material breaks much after the fashion of "green" cheese. It is rubbery under compression, but does not resemble rubber in tenacity or cohesion. When dry, the material ranges from hard clods to a horny mass of high tensile strength. The shrinkage in drying is very great, especially in the hornlike matter. The moist material ranges in color from dark brown in the specimens rich in organic matter to grayish in specimens containing more inorganic matter. All of the specimens studied were readily attacked by molds, which in some cases grew in great profusion on the samples. Samples exhibited a rather characteristic "swampy" or "mucky" odor when wet, and a characteristic odor of humic soils when moist.

Jan 4, 1918

By Carrol M. Beeson

Reasons are given for using a Boyle&apos;s-law porosimeter in conducting core analysis for either routine or research purposes. Among other things, it is pointed out that such a porosimeter permits the measurement of all basic properties on the same sample, thereby eliminating the sources of error inherent in the use of adjacent samples. References are made to investigations of gas adsorption on various porous materials, to show that the use of helium in Boyle&apos;s-law porosimeters reduces to negligible proportions the error due to the adsorption or desorption of the operating gas. Two Boyle&apos;s-law instruments are described. which permit accurate and rapid measurements of porosity. Schematic sketches and explanation:; are included, along with derivations of equations required in performing precise determinations. Summaries of data obtained during calibration are tabulated and analyses of the data are resented as indications of the precision and accuracy of each device. Comparisons are also shown for measurements made with each of the instruments on the same test pieces and cores. INTRODUCTION An accurate porosimeter, operating on the principle of Boyle&apos;s law. is of considerable value in the analysis of cores for either routine or research purposes. This is due primarily to the fact that the measurement of porosity with such an instrument leaves the sample free of contamination by any liquid. When used in conjunction with an extraction apparatus&apos; for determining oil and water saturations, a Boyle&apos;s-law porosimeter permits the measurement of all basic properties on the same sample. This eliminates the sources of error inherent in the use of adjacent samples, or the necessity of determining porosity after all other properties have been obtained. Large errors may result from combining measurements made on adjacent samples in order to obtain a single property. This type of error is definitely involved when oil and water are measured with one sample, and the pore vo1ume is measured with an adjacent one. Furthermore, the source of error would be present to some extent, even if the analyst could choose the samples so they were truly adjacent from a geological standpoint. The use of adjacent samples in routine core analysis also necessarily decreases the probability of correlating core properties. For example, the chance of correlating the "irreducible" interstitial-water saturation with permeability, is bound to be greatly reduced by measuring these properties on "adjacent" samples. For research purposes, amplification is scarcely required concerning the greater flexibility of a method for measuring porosity which leaves the core free of contamination by any liquid. Even under those circumstances which require that the core be saturated with a liquid, a previous measurement of porosity with a gas is useful in determining the degree of saturation that has been attained in the process. Furthermore, for comparable accuracy, porosity usually may be determined more rapidly with a gas than with a liquid. This advantage of the Boyle&apos;s-law instrument is most outstanding when the determination time is compared with that required in obtaining porosity by evacuation of the core followed by saturation with a liquid of known density. Several porosimeters which operate on the principle of Boyle&apos;s law have been described2,3,4,5,6,7 in the literature. No comparison will be attempted between those instruments and the ones described herein. Before helium gas became readily available, Boyle&apos;s-law porosimeters were subject to an appreciable error due to the adsorption of the operating gas on the surface of the core solids. There is considerable direct and indirect evidence in the literature to support the contention that the adsorption of helium on porous solids is negligible at room temperature. In discussing the use of Boyle&apos;s-law porosimeters, Washburn and Bunting2 stated that "for most ceramic bodies dry air is a satisfactory gas, but hydrogen will be required in some instances. Helium could, of course, be employed for all types of porous materials at room temperatures or above." Howard and Hulett8 obtained evidence that the adsorption of helium was negligible at room temperatures, even on activated carbon ; for the density measured with this gas was unaffected by changes in pressure or by changes in temperature from 25 °C to 75 °C. For oil-well cores, Taliaferro, Johnson, and Dewees" obtained lower porosities with helium than with air, but apparently did not study helium adsorption. From the work of these investigators, it follows that the use of helium in Boyle&apos;s-law porosimeters reduces the error due to gas adsorption to negligible proportions. This makes it possible to construct instruments which permit the determination of porosity with (1) a high degree of accuracy, (2) with great rapidity, and (3) without contamination. THE KOBE POROSIMETER The fundamental design of the Kobe Porosimeter was developed by Kobe, Inc., which firm built about 12 of the instruments during 1936 and 1937. Since that time, seven or eight more have been constructed with their permission, making a total of about 20 that have been put into operation.

Jan 1, 1950

By F. A. Harvey

DURING the last few years, there has been a constant tendency toward increasingly high temperatures in many lines of industry. The necessity for increased production of coke gave a 16-hr. coking period where we used to have 24 or even 30-hr. periods. Mechanical stokers have increased the temperatures in boiler furnaces. The use of a chain-grate stoker with coke-breeze fuel necessitates a low arch in the furnace and temperatures run much higher than firebrick were formerly called upon to stand. These higher temperatures have necessitated more rigid tests and the separation of even high-grade firebrick into separate classes. More severe tests mean higher temperatures and closer control, and this, in turn, means better pyrometer tubes. Platinum couples do not have a very long life when used at temperatures exceeding, say, 1200° C., but the proper selection of a high-grade brick to be used in a-boiler setting will save the cost of several couples; and with freight rates continually increasing it becomes increasingly important to know where brick may be bought, nearest the job, that will prove satisfactory. Couples that will stand continuous use at higher temperatures, of tungsten, molybdenum, or other metal, will doubtless be forthcoming as soon as the need becomes sufficiently urgent. There are on the market several tubes that are entirely satisfactory for temperatures up to 1300° C., if properly protected from heat shock. The Semet-Solvay Co. makes a practice, however, of testing silica and clay firebricks at 1450° C. for 72 hr., and so far we have been unable to find a tube that- is entirely satisfactory for this purpose. A graphic record of the temperature during the entire test is extremely desirable and hence we have been trying out anything that gave promise of success. Several years ago we were using insulating tubes, made purely for electrical work, of vitrified porcelain. These tubes stood up under any temperature we were able to reach and were apparently impervious to gases. When this stock gave out, due to mechanical breakage, we tried other insulation tubes only to have them melt down like glass. Marquardt Masse tubes were tried next under a statement from the distributors

Jan 9, 1919

By J. J. Rutledge

THE first method of working coal mines in the middle western states, more particularly in Illinois, Indiana and Missouri, was by means of the so-called single-entry method. In this method a single main passageway, or entry, was driven in the coal seam. with no parallel passageways, and from this pas-sageway or entry there were turned at intervals sim-ilar cross-passageways or entries, and from these cross-passageways, if the coal seam worked lay fairly horizontal, rooms were turned right and left. These crude methods of working were followed when the com-panies opening the mines were small and of very limited capital, and when the demand for coal was small and irregular. The principal desire was to produce coal in the short-est possible time and at the cheapest price. The chief evil resulting from such method of working was de-fective ventilation, although there were other serious drawbacks. There were then few or no good mining laws and no restrictions on those operating the coal mines. The hours of labor were long, the wages low, and the miners accordingly worked hard. All the coal was either sheared or undercut with a pick by hand. Very little solid shooting and no machine mining was done. What little air entered the mine, openings was introduced through the entries or. headings and thence conducted through the rooms by means of curtains; in many cases, as the workings became more exten-sive, the number of curtains added so materially to the mine resistance that ventilation was extremely in-efficient. Shots were fired by the miners at any time during the working shift and consequently there was more or less powder smoke or fumes in the mine work-ings all day long. Moreover, the working days were much longer than at present. The fine, dry coal-dust falling from the miners&apos; picks while they were shear-ing or undercutting the coal filled the mine atmosphere and was taken into the lungs of the mine employees.

Jan 2, 1927

By A. U. Seybolt

Precipitation of FeO from Fe-O solid solutions has been studied by metallographic methods. Such precipitation, which is visible, is composed largely of barely resolvable spheroidal particles. No metallographic evidence has been found for grain boundary oxide films. Oxygen diffusion into a iron does not occur chiefly by inter-granular penetration. IN an earlier communication&apos; dealing with the solid solubility of oxygen in a iron, it was shown that under one set of conditions it was possible to show FeO precipitated from supersaturated solid solution. However, to assist in rationalizing the effect of an FeO second phase upon the mechanical properties of iron, it would be desirable to have more information on the possible modes of precipitation and on the thermal treatments required to produce precipitation.

Jan 1, 1955

By E. F. Johnson, F. H. Brinkman, H. J. Welge, S. P. Ewing

This paper presents a method for predicting the manrler in which oil will be displaced from a porous body by enriched gas. The calculations apply to a gas rich enough to give a partially, but not a completely, misci-ble displacement. The method — a three-component, two-phase analysis — takes into account condensation of some of the intermediate hydrocarbons from the injected gas into the oil, as well as enhanced volatility of heavier hydrocarbons at elevated pressures and temperatures. The condensation swells the oil and decreases its viscosity, thus aiding in its recovery. The calculations have been extended to apply to actual crude oil-natural gas systems by arranging the components into three groups according to their volatility. As an approximation, each group is then treated as a single component in the analysis. The influence of an angle of dip for an inclined displacement is also taken into account. The recovery predictions are corroborated by experiments which used both consolidated sand cores and un-consolidated glass beads. In some of these tests, actual live crude oil was displaced by a multicomponent gas typical of enriched gases used in oil fields. INTRODUCTION This paper presents a method for predicting the amount of oil that can be displaced from a homogeneous, linear, porous body at various stages during the injection of enriched, or "wet", gas. The porous body can be in either a horizontal or an inclined position. &apos;This type of displacement is sometimes known as condensing gas drive The method is developed especially for the case in which the injected gas is enriched enough to be partially, but not completely, miscible with the reservoir oil. The need for a calcula-tive procedure for this type of operation is emphasized by the number of field projects where completely miscible drives are not practical, but where near-miscible conditions are feasible. The factors taken into account in the predictive calculations include: (1) the condensation of gas components into the oil, with a resulting increase in oil volume; (2) the lowering of oil viscosity by the addition of lighter ends from the gas; (3) the increase in oil volatility at high temperatures and pressures; and (4) the physical displacement of the oil by the gas. The techniques developed in the paper can be extended to other nonequilibrium displacement processes. Other such processes that we have analyzed include a displacement by lean gas which stripped intermediates from the oil, and a water flood in which the water con. tained in solution a substance somewhat soluble in the oil. ANALYSIS OF ENRICHED-GAS DRIVE GENERAL PRINCIPLES Our method for predicting the amount of oil that can be displaced by an enriched gas uses an analogy between a three-component and a multicomponent system.&apos; The predictive method is based on these assumptions: (1) constant, or nearly constant, pressure; (2) complete equilibrium by diffusion perpendicular to the main direction of flow, but no significant mixing along the direction of flow; (3) constant injection velocity; and (4) flow in a linear porous body. The composition of a liquid or a vapor with respect to three components can be plotted on a three-component, or ternary, diagram like that in Fig. 1. Let Point A represent the composition of the oil originally in place. In this case, Oil A is undersaturated with gas. If Point A lay on the equilibrium Curve BF, the oil would be saturated. In the extreme case where the original oil contained no intermediates or dissolved gas, Point A would lie at the lower left-hand corner of the ternary diagram. In a displacement of Oil A by Gas D, there will be a progressive change in the composition of the oil phase as more and more gas is brought into equilibrium with the oil. The end result of this progressive change is an oil having the composition represented by Point F. This oil is richer in intermediate hydrocarbon and methane than the original oil and, therefore, has a greater forma-