Search Documents

By Alfredo O. Del Campo

Copper concentrate smelting has been the subject of significant improvements during the last three decades. Several new processes are being successfully applied at industrial scale, and probably no new copper smelter will be built with the old-fashioned reverberatory furnace. However, because of financial reasons, the existing reverberatory furnaces, which smelt a significant part of the copper produced worldwide, are likely to last at least another decade. Some improvements have been introduced in reverberatory smelting practice, the best known being the use of oxyfuel burners. However, efforts to optimize the reverberatory furnace operation through automatic control have not been reported. The complex and semi-continuous nature of the process makes it dificult to find a suitable strategy for its automatic control. Many factors, like fuel economy, productivity, boiler capacity, refractory wear, converter slag return, copper losses in discard slag, etc. are interconnected. The chosen control strategy should take into account all these factors to achieve good economic results. A detailed discussion of these problems is presented.

Jan 1, 1984

By C. R. Sandberg, C. A. Connally, N. Stein

This paper describes the results of volumetric efficiency tests on oil well pumps handling gas oil mixtures. The work was performed in a large scale, above ground unit wherein test conditions could be accurately controlled and measured. The main variables studied were gas/oil ratio (including gas from solution and free gas mixed with oil), pump compression ratio, pump stroke length, pump speed, and clearance volume between the valves at their closest approach. Results are presented for two different pumps and for oils of two viscosities. Relatively small amounts of gas entering the pump resulted in large decreases in volumetric efficiency. Under conditions where the pump was operating at reduced efficiency because of the presence of gas, it was found that variation in the clearance volume between the standing and traveling valves had a considerable effect on pump efficiency level. This effect of the valve clearance volume was found to be significantly altered by the viscosity of the oil used in the tests. The effects on pump efficiency of the other variables studied were found to be relatively small over the range of conditions utilized. INTRODUCTION The production of oil by pumping is often hampered by low volumetric efficiency. A direct increase in lifting costs results from low volumetric efficiency. An indirect increase in lifting costs, probably greater than the direct increase, results from additional wear and tear on pumping equipment and from the down-time necessary for the repairs which can be traced to low-efficiency operation. Both increases in lifting costs tend to reduce economically recoverable oil. A number of different factors can contribute to low pump efficiency. A known basic cause of low efficiency is the presence of free gas in the pumped fluid. Pump volumetric efficiency is calculated only on the basis of liquid pumped and because any free gas pumped is discounted, this volume of free gas would represent a loss of pump efficiency. However, gas also causes a reduction in pump efficiency because it is a highly compressible fluid. It is known that pumps some- times "gas lock" because of excessive gas-to-liquid ratios in the pump barrel. Little is known of the role of gas compressibility in the intermediate case where the pump is operating at low efficiency. The opinion exists, however, that oil-well pumps tend to operate at higher efficiency with long stroke lengths at low speeds, but no quantitative studies of these pumping variables have been reported. It was believed that a much better understanding of the variables which control pump volumetric efficiency could be obtained and that possibly some suggestions as to the methods for increasing efficiency might be found from a study of the operation of pumps handling gas under closely controlled conditions. Previous investigators have studied the effects on pump efficiency of such factors as oil viscosity, oil temperature, slippage of oil. past pump plungers, pump submergence, valve size and spacing, pressure above pump plunger and fluid vapor pressure. However, none of these published investigations were conducted with pumps being subjected to large amounts of gas such as might be the case in a pumping well, nor did any of the investigations study the effect of variation in stroke length or pump speed. A large-scale teat unit was therefore constructed for studying the operation of pumps handling gas and for evaluating effects of such variables as pump stroke length and pump speed. PROCEDURE AND EQUIPMENT A schematic diagram of the pump testing equipment is given in Fig. 1. A 45-ft length of 6-in. casing is mounted vertically in a 65-ft tower. Sight ports are mounted in the casing at intervals near the location of the pump intake and the liquid level in the casing. These sight ports are fitted with Lucite windows sealed by neoprene "0" rings. The Lucite windows are machined to conform to the I.D. of the casing so that no obstruction to flow is present along the casing wall. The casing is fitted with a tubing head and 2-in. tubing is hung inside the casing. Pumps are seated in a shoe attached to the 2-in. tubing. A 1-in. polish rod is attacked directly to the pump without any intervening sucker rods. The top of the polish rod is attached to the weight carrier, which contains a number of weights to be used to force the polish rod in against tubing pressure on the down-stroke. This is necessary because a long string of sucker

Jan 1, 1953

By AIME AIME

ON April 7 the twentieth national Open-hearth Conference of the A.I.M.E. will be held in Birming¬ham, Ala., in conjunction with a meeting of the Committee on Blast Furnaces and Raw Materials. At least 300 engineers and operators are expected to attend. Birmingham, the industrial city and iron, and steel center of the South, has been called the "Magic City." Men actively engaged in business in Birmingham today have seen practically every building in the business district erected, have witnessed the establishment of every existing industry, and have hunted birds cm the site now one of the busiest corners of the business district. Incorporated as a town in 1871, the city today has a population of more than 380,000 in its metropolitan area. It is

Jan 1, 1937

By David Donoghue

Efforts made in the year 1930 and in previous years restricted production in most of the fields of Texas to a point that was satisfactory, at the beginning of 1931, to the majority of producers and buyers. In the Panhandle, North Texas and West Central Texas districts, a few operators with refinery affiliations or contracts either ignored, or by virtue of injunction suits, did not comply with the Railroad Commission's orders, and there was some oil sold at less than posted prices, which, with the Oklahoma City difficulties, caused the first general price reduction. More could have been done perhaps to help the situation on the Gulf Coast and in the Laredo district, but natural advantages are not readily surrendered. East Texas Proration troubles in 1930 were insignificant when compared with those of 1931. In January, 1931, efforts were begun to convince the producers and citizens of East Texas of the necessity of curtailment. Opposition quickly developed and meetings were held in the towns of the region and proration denounced vigorously. Notwithstanding a strenuous campaign for additional legislation waged by many producers, the regular session of the State Legislature refused to strengthen the conservation laws and passed only the Marginal Well Bill, designed to prevent the Commission from prorating small wells. The Railroad Commission held a heated hearing on East Texas in the latter part of March. During April the Commission issued three orders based on the Yates plan for the proration of the East Texas field. Each succeeding order raised the allowable for the field. In June the opposition held more mass meetings at which a plan based on acreage was endorsed. Apparently on the theory that any plan was better than none, the Commission issued an order on July 2 embodying some of the features of the proposed plan, limiting production to 250,000 bbl. per day, and dividing the producing area into 20-acre units participating equally in the outlet. Owing to the bringing in of many wells and the many violators of the Commission's orders, production increased to such an extent that prices went as low as 5c per barrel.

Jan 1, 1932

By J. Donald Graham, John G. Kuhn

The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an ore body, no more and no less. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. The method for controlling development drilling programs to be described was developed during the latter part of a major development drilling project at the Christmas mine of Inspiration Consolidated Copper Co. in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous ore bodies of the porphyry-copper type would be the most likely candidates for application of the technique. Discontinuous ore bodies would not be amenable. The method is based on the measurement of the linear correlation between the spatial distribution of two sets

Jan 1, 1973

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. W. Leonard

One of the more obvious phenomena which relate to coke formation is that soft coals of low volatile matter content tend to yield hard or high strength cokes while hard coals of high volatile matter content tend to yield soft or low strength cokes. This observation led researchers of the Coal Research Bureau of West Virginia Univ. to study the possibility of using Hardgrove grindability as a supplemental rank indicator for coking properties. Grindability has been used for many years as a means to measure the resistance of coal to comminution but it has rarely if ever been considered for evaluating coals for carbonization. The coal proper- ties which are measured by grindability are complex, but recent work with the difficult-to-correlate high volatile coals has demonstrated that a 93% correlation exists between grindability and the total petrographic rnicrinites, exinites, and resinites. This work demonstrated that inherent ash had no apparent effect on the grindability of high volatile coals, suggesting that the coal substance is apparently harder than the associated ash. These observations, together with the patented Burstlein process," indicate that the distribution of hard and soft components in the individual high volatile coals and blends of coals may be quantitatively interrelated to coke stability through selected ranges of coal volatile matter. The objective of this progress report is 1) to demonstrate the statistical relationships which exist between coal grindability and the numerous coal petrographic entities and 2) to present the results of initial studies concerning the correlation of the coke physical strength index of stability with coal volatile matter and grindability.

Jan 3, 1964

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By J. F. Cuderman

A technique using propellants has been developed for producing multiple fractures about a wellbore. The use of propellants having a range of burn rates permits precise control of combustion gas release and thereby of borehole pressurization. The pressure rise- time is the key variable governing fracture behavior. The peak pressure attained is of secondary importance and appears to be a function of in situ stress and loading rate. The fracture geometry is governed by the in situ stresses and pressure risetimes. The major fractures occur along the principal planes of stress and along apparent planes of maximum shear stress.

Jan 1, 1984

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By V. R. Degner

The trend in both the metallic and nonmetallic mining industry is toward processing increasingly higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This Paper reviews the R&D approach used in translating smaller flotation machine experience to the configuration of a 28.3 m3 (1000 cu ft) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1981

By Frank T. Weems

The basic operating properties of the DorrClone are discussed and certain metallurgical applications which exploit these properties are presented. An effective method of controlling the consistency of the DorrClone underflow is described. THIS paper presents in a general manner some of the applications of the DorrClone (Dutch States Mines cyclone) in the metallurgical and heavy chemical fields. Technical or mathematical analyses of the design factors and of the mechanism whereby the cyclone effects its separation have been capably treated in a series of previous papers.'-' Engineering and operational aspects of a few installations and laboratory tests have been chosen to emphasize the unique classification characteristics of the DorrClone and to illustrate its utility in certain difficult situations. Its use in coal washing and heavy-media operations are not considered. Some 25 or more industrial installations and applications of the DorrClone in the metallurgical fields are operating at present, ranging from single trial units to complete batteries composed of a multiplicity of units. The data were obtained in part from some of these, and in part from operations of units at the Westport Mill, the laboratories and testing plant of the Dorr Co. at Westport, Conn. The DorrClone was developed, in principle, by the research dept. of the State Mines, Limburg, Holland, during World War 11. Its first use was to dewater a —50 micron sand used as a dense medium in coal washing. The metallurgical wet cyclone was first publicized by Driessen and Yancey and Geer.6 ince then the cyclone has been studied as a means of de-watering, heavy media concentration, and fine size classification. The DorrClone is shown in Figs. 1 and 2. pulp to be treated is pumped through the feed nozzle, A, into the feed cylinder, B. The feed nozzle is of rectangular cross-section, the outermost edge being tangent to the feed cylinder walls. Feed shims, C, may be attached to the innermost walls to adjust the open area of the feed nozzle available to entering pulp. The tangential injection of feed under pressure supports the vortex action of the pulp that has been detained in the cyclone; the centrifugal forces of this vortex throw the coarse particles to the walls of the cone, D, where they collect and pass downward and out through the adjustable apex opening, E. The fine particles contained in most of the water that entered with the feed pulp move to the inner spiral of the vortex and flow out through the vortex finder, F, contained in the orifice plate, G, which forms the top of cyclone chamber. The overflow pulp may then spray freely into a spray chamber, H, surmounting the cyclone or pass directly into a 90' elbow, I, of somewhat larger diameter than the vortex finder. Installation Where more than one cyclone is to be installed, best overall efficiency and ease of control are obtained with equal distribution of both pulp volume and weight of solids among the cyclones, and with the same pressure being maintained at each cyclone feed nozzle. Fig. 3 is a suggested arrangement for feeding two or more cyclones in parallel. Feed pressure control: Under normal operating conditions it is not unusual for some surge to exist in the feed that is to be sent to the cyclone. As will be discussed later, surges in the solids content of the pulp are usually not of great operational consequence, but surges in feed volume are a problem. Several systems have been devised for absorbing surges in feed volume, each involving a surge tank. If the surges are small and fairly rhythmical, a tank of sufficient size might be installed to dampen out

Jan 1, 1952

By C. O. Brawner

INTRODUCTION Tailings dams up to about 200 ft. high are proposed to store tailings for a major mining operation on Marinduque Island in the Philippines. The original design of the dam utilized a compacted laterite starter dam followed by hydraulic placement of cycloned sands to form slime retaining dykes along the outer face of the dam. The upstream method of construction was proposed. In view of the failure of numerous tailings dams in Chile during the EL Cobre earthquake (I), an investigation was performed to assess the earthquake stability of the proposed dam. This included a soil investigation on the first cycloned sand dyke, which had been built to a height of 45 ft. Results indicated that the density of the sand was much lower than existing empirical criteria consider to be necessary for resistance to liquefaction. As a result, the dam was redesigned. The downstream method of construction was selected and a yearly construction program was developed to make use of sand available by cycloning. To increase shear strength, improve resistance to liquefaction, and to utilize steeper slopes, compaction of all sand in the dam was specified. A special underdrainage layer and toe drains were incorporated in the design. Details of the decant system and surface erosion alternatives are described. SITE CONDITIONS The mining project is located in the Philippine Islands. At the present annual rate of production, about 4,230,000 cu.m. of tailings will be produced yearly. The volume requirements for tailings storage design for the first 10 years of operation are in the order of 45,000,000 cu.m. The topography near the mine is mountainous with many gullies and canyons carved out by high intensity rainfall and runoff. The bedrock, which is generally shallow and weathered for a considerable depth, is overlain by laterite soils. Vegetation is comprised largely of palms, banana trees, and tropical shrubs and grasses. Precipitation is heavy. The average yearly rainfall over 24 years is 65.2 in. and the maximum recorded 24 hour rainfall is 9.0 in. High intensity rainfall is associated with typhoon storms, which are a seasonal threat inthe Philippines. Fig. 1 shows a summary of monthly precipitation.

Jan 1, 1972

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

A SERIES of awards for men and women in indus-try who by their inventions, heroisms, vision, and powers of mediation are contributing daily to the life and well-being of America in a substantial way, will be given by the Harmon Foundation. The series, to be known as "Awards to Honor Men in Industry," consists of two cash prizes, $1,000 and $500 each, accompanied by a gold and silver medal respectively, and 100 bronze medals. No one above the rank of foreman will be eligible. Because of the diversity of .American indus-try, the Foundation is planning to confine its awards during the first year to the following branches of man-ufacturing: automotive, building, electrical, metal and textiles, including clothing. The Harmon Foundation invites the general public, newspapers, organizations and employees to bring to its attention such persons as they may deem worthy of the award.

Jan 3, 1928

F. JOHNSON,* Birmingham, England (written discussion t).--. Mr. Skowronski's first melting experiments tend to show that ingots with a "level set" may be obtained without oxygen. Now it is characteristic of all metals which occupy a smaller volume when solid than they do when molten to "pipe." In vertical-cast ingots, this pipe resembles a horn-shaped cavity, with the wide mouth uppermost. In horizontal-cast ingots, the pipe is a longitudinal furrow along the center-line of the ingot surface. If copper be successfully deoxidized and degasified, this furrow will inevitably be produced. In the author's oxygen-free ingots, it is. clear that gases were occluded and these gases effectively opposed the formation of a pipe or furrow by shrinkage (fluid contraction). It is riot a special property of any particular gas which produces this effect. Hence it is not surprising that the author has succeeded in producing level and overpoled ingots through the agency of sulphur. dioxide gas. That he has counteracted the overpoling influence of sulphur by means of oxygen is somewhat difficult to explain, since the well known reaction between cuprous sulphide and cuprous oxide should result in the production of sulphur dioxide gas. Why the presence of excess cuprous oxide should neutralize the overpoling influence of this gas without eliminating sulphur is not at all clear. It is to be regretted that the oxygen was not determined in the bars given in Tables 3 and 4. It is by no means established that sulphur is responsible for the over, poling of ingots given in Table 4, since carbon was used for overpoling. If, however, the same kind of poling treatment was given as that applied in the case of ingots in Table 1, the responsibility of sulphur assumes more definite shape. The author rightly points out that Mr. Johnson's theory of the equilibrium between gases and cuprous oxide does not explain why a simple addition of cuprous oxide does not correct an overpoled charge. Such a charge must be re-worked to "set" copper. This re-working (rabbling) undoubtedly forcibly removes the excess gases, which are not removable by cuprous oxide.

Jan 11, 1918

By L. J. Howell, R. C. Sommer, H. H. Kellogg

WORK described herein was undertaken with the aim of determining some of the physical-chemical properties of electrolytes suitable for the electrodeposition of pure zirconium metal. In this paper the phase diagram, vapor pressure, and activities in the melt are considered. In a companion paper,' the electrolytic conductivity of some of these melts is reported. The melts studied were mixtures of NaCl and/or KC1 with ZrC1,. Chloride melts were chosen for study because 1) if the electrolyte is to be useful for industrial electrodeposition of zirconium, the chlorides will be preferred to the relatively costly bromides and iodides; 2) fluoride melts were being studied in another laboratory (Horizons Inc., Cleveland); and 3) melts containing oxygen, in any form, are unsuitable for preparation of pure zirconium, because of the great affinity of this metal for oxygen. Unlike electrodeposition from aqueous solution, the fundamental behavior of fused-salt electrolysis is poorly understood. In most cases, such basic electrochemical information as the phase diagram of the melt system, activities in the melt, conductivity, the nature of the current-carrying ions, the equilibrium electrode potentials, and the overvoltage behavior of the electrodes is unknown to the researcher who would develop a new electrodeposition process employing a fused salt. This research project was designed to supply information about some of these basic physical-chemical properties so that an intelligent choice of electrolyte for electrodeposition studies could be made. Experimental The experimental difficulties-encountered in this work result from the properties of zirconium metal and ZrC1,. ZrC1, is a solid which sublimes at 334°C. It is rapidly hydrolyzed by moist air to HC1, ZrOCl,, and ZrO,. Unusual precautions were exercised in this work to prevent hydrolysis of ZrC1, and rigidly to exclude oxygen, nitrogen, hydrogen, and carbon from the melts under study. These elements are known to react with and contaminate zirconium metal. All melts were studied in vacuum systems, i.e., in the presence of ZrC1, vapor only. Transfer of ZrC1, to or from the melts was accomplished entirely by vacuum sublimation. In this way, neither the melts nor the ingredients thereof were permitted to

Jan 1, 1958

The ability of activated charcoal or carbon to adsorb complex metal ions has been recognized for many years, but it wasn't until the late 1940s and early 1950s that attempts were made to employ carbon-In-Pulp or C. I. P. processing to the recovery of gold. Early plants using the process were those at the Golden Cycle in Cripple Creek, Colorado, the Getchell Mine near Golconda, Nevada, and at the Idria Mine in Honduras. Recovery of the carbon from the pulp was done by screening or flotation, and recovery of gold from the carbon was done by burning the carbon (a very difficult task) or by sending it to a smelter. Unfortunately at the time, the price of gold was still fixed at $3-5 per ounce and labor costs were rising to the point where these mines were no longer able to operate. Consequently, C. I. P. treatment was temporarily forgotten. In the early 1970s, however, Homestake Mining Company at Lead, South Dakota, were being forced by environmental regulations to discontinue the use of mercury for amalgamation in their 7,500 ton per day plant, and at the same time were encountering high labor costs in the slime circuit of the plant, where over 2,000 tons of slimes were filtered each day in Merrill plate and frame filter presses. Shortly before that, researchers of the United States Bureau of Mines had developed the caustic -cyanide method of stripping gold from activated carbon and an electrolytic cell (now known as the Zadra cell) to recover gold from the carbon strip liquor. Homestake and the United States Bureau of Mines then jointly operated a C. I. P. pilot plant at Lead. Results were immediately favorable and a 2,400 ton per day C. I. P. plant was then built to treat the slime fraction of the Homestake ore. (See Au and Ag Cyanidation Plant Practice, Volume I, SME of AIME, 1975. Later, Homestake built a second plant at Creede, Colorado, to treat the slime fraction of the tailings from a silver-lead flotation plant. Next was Duval Corporation's 3,000 ton per day C. I. P. plant at Battle Mountain, Nevada. Both of these latter plants are described in this volume. C. I. P. operations under construction at the time of this writing are as follows: Pinson Mining Co. , Nevada Gold Freeport Gold Company, Nevada Gold Compania Minera El Indio, Chile. Silver and Gold

Jan 1, 1981