Search Documents

By George E. Aiken

Modern high speed bucket wheel excavators (BWEs) can dig materials which power shovels can't handle without blasting. Yet these machines are not used in any large, open pit ore mines in the United States. American mining has been slow to use the wheel's special capabilities of high production volume at low cost, due perhaps to a traditional familiarity with shovels and draglines and/or the lack of data of BWE operation, design and cost. Of course, shovels and draglines can not be replaced by BWEs in all cases, but under suitable conditions bucket wheels can out-perform other conventional excavators and simultaneously permit significant operating savings. The latter aspect will become increasingly important to American mining men because as more low to medium grade orebodies are found in regions of thick overburden, better and cheaper ways of uncovering them must be developed. Typical of such areas are the thick alluvial fans of the Southwest and the glacial drift areas in northern regions. Much of this material would handle well with a wheel excavator without blasting, although ripping might be necessary in some cases.

Jan 1, 1966

By Samuel Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study. and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main, system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change.

Jan 1, 1928

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson's ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

By D. W. Rudd, D. W. Vose, J. B. Vetrano

In an earlier paper the permeability character of Mo-0.5 pct Ti to hydrogen was described.' It was shown that this alloy is a more effective barrier to the passage of hydrogen than previously studied systems, i.e., copper,2 nickel,3 and several stainless steels.4 The permeability of Hastelloy B to hydrogen was investigated as a material having promising high-temperature structural properties which might have a low permeability to hydrogen. The general theory of permeation has been previously discussed,' and here only a summary of the more important results are given. It is found that except for very thin membranes, at low temperature, permeation of a gas through a metal barrier is determined by the rate of diffusion of the gas through the crystal lattice of the specimen, and that for hydrogen and the common diatomic gases, this passage involves dissociated particles as the diffusing species. The rate of permeation for hydrogen is therefore proportional to the square root of the pressure. It has also been found that the rate of permeation is inversely proportional to the thickness of the barrier. The apparatus used in this investigation was fundamentally the same as that employed in previous studies,' except that several simplifications result in the case of Hastelloy, since oxidation at the temperatures investigated is no longer a problem and welding of the specimen is relatively easy. A cross section of the membrane assembly is shown in Fig. 1. When finished, the assembly is about 5 in. long. The wall thickness is about 6 times the membrane thickness. The membrane (A) can be maintained at

Jan 1, 1963

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By C. H. Bowen

Industry needs a generally applicable means of defining average grain sire and grain size distribution. Students of sediments have explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data.

Apr 1, 1956

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

By L. M. Cathles, H. R. Spedden, E. E. Malouf

Fluid flow through an igneous rock formation will occur mainly through fractures. A non-diffusing or slowly diffusing tracer (such as .5µ silica spheres identifiable under electron microscope) will arrive at a monitor well when enough fluid has been injected to displace the volume of water in the flow fractures between the injection and monitor wells. A rapidly diffusing tracer (such as NaC1)-will diffuse into the matrix blocks and so a volume of tracer nearly equal to the total fluid volume contained in the rock formation between injection and monitor wells must be injected before significant diffusing tracer arrival will be noted. The flow fracture porosity is typically one hundred times smaller than the total porosity of an igneous formation. The shift between diffusing and non diffusing tracer arrivals, together with the diffusional characteristics of the tracers, can define the diffusional accessibility of the matrix blocks of an igneous formation. A field test of these concepts and the problems encountered will be described.

Jan 1, 1974

By James W. Guider

Of all the technology available to the iron blast furnace operator, raw materials preparation [(Fig. 1)] is by far the most important. Superior raw materials have been basic to the success of the Japanese steel industry, and they are just as essential to the American steel industry in winning its competitive battle against foreign government subsidized steel imports. Therefore, the mine operator and the ore beneficiation engineer must strive to produce the highest quality raw materials possible to meet the precise demands of the modem blast furnace and steel plant.

Jan 1, 1982

By High Archbald

It is possible to construct a simple diagram of the earnings, or the production, of the men employed at a coal mine that will show not only if the conditions tend toward contentment among the men, but if the operating distribution of the work is correct. As earnings are the greatest cause of discontent, even exceeding all the other causes, if contentment exists in the matter of earnings, the likelihood of other discontents flaring up is greatly lessened. The basis of such a diagram would be the Gaussian curve of the normal variation in human ability. Such a curve has long been recognized. H. L. Moore,' in discussing the quantitative relation between wages and ability says: "It has been pointed out that industrial efficiency is dependent upon physical, mental, and moral qualities, and these qualities . . . there is good reason for regarding as being distributed according to the Gaussian law.

Jan 1, 1925

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing'. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing', There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry's law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H' is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By Hamish D. S. Miller

Currently the underground potash mines in Canada extract about 40% of the available ore, leaving the other 60% behind in the form of stabilizing pillars. The presence of water in the overlying formations requires that any disturbance due to mining be such that no water will enter the workings. This paper deals with the factors that influence the stability of the rock surrounding the mine excavations and looks at the effects of these factors when a system of increasing the extraction is considered.

Jan 1, 1983

Aaby, Alton O , (S'47) Univ of Minnesota, Mimeapolis, Minn Aaby, Waldo S , (S?48) Univ of Minnesota, Minneapolis Minn Aalde, Kaare, (S'48) Univ of Nevada, Reno, Nev Aaring, Floyd D , (S'48) Univ of Oklahoma, Nor man, Oka Aaronson, Hubert I , (S'47) Carnegie Inst of Technology, Pittsburgh, Pa Abbott, Peyton Osborn, (S'46) 1502 Westover, Austin 21, Texas Abel, Malcolm D , (S'47) Univ of Texas, Austin, Texas Aberg, Richard S , (S'47) Univ of Minnesota, Minneipolis, Minn Abrahamson, Guy C , (S'43) 420 W Dennis St , Wilmington, Calif Abrahao, Benjamin, (S'46) Escola Politeenica da Unnersidade, de Sin Piulo, Braizil Achter, Meyer R , (S'46) Carnegie Inst of Tech , Pittsburgh, Pa

Jan 1, 1952

By D. N. Sutherland

The cassiterite flotation circuit at the Renison concentrator has operated with increasing levels of automatic control since late 1981. The circuit operates at high levels of recycle which make it difficult to control manually so that the initial control strategy was to stabilize the mass flows around the circuit prior to circuit optimization. Control of the air supplies to the flotation banks was introduced to achieve this stabilization and initial results indicated that some success has been achieved, as indicated by improvements in the overall circuit performance and reduction in the stream variabilities. These improvements were gained through control of the major recycle to the roughing stage which dominates the circuit behaviour. Feed-forward control of collector addition has also been introduced successfully, but attempts to control the final concentrate grade have been less satisfactory. This work is continuing and the objective of current activity is to include the three cleaning stages in an overall circuit control scheme as a first phase of metallurgical optimization of the operation.

Jan 1, 1984

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.'s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

By John F. Blandy

IT is not my intention in this article to consider this subject in the light of the geographer or geologist, but rather in that of the mining engineer, and to endeavor to show the necessity and value to him of studying the minor details of the field or district in which he may be engaged. I t has been said by a distinguished geologist that "the natural boundaries of the geographer are rarely described by right lines. Whenever they occur, however, the geologist may look for something remarkable." And again : " Physiognomy is no idle or doubtful science in connection with geology. The physiognomy of a country indicates almost invariably its geological character." Our country furnishes examples enough of the truth of these remarks, and in no part of it is it so beautifully illustrated as in our own State, which has been so ably described by Prof. Lesley in his admirable little work on the "Topography of Coal." As the great mountain lines become guides to the geologist in determining and mapping out the geography of the formations, so do the minor details of topography become guides to the mining engineer in conducting his explorations, discovering of dislocations, and determining the character of the deposits which are the object of his search. I t is therefore requisite that he should, whilst making his surveys, pay the strictest attention to every variation of the landscape and surface of the ground. Until he has mapped out every feature he may be unable to read the geological changes which may have

IT is not very necessary for those who work ores to return the litharge to lead, because they use litharge in place of lead ore and they use it the more willingly when it still contains some trace of silver. For the cupeling hearth can never be so well made or so cleanly operated that some little bit of silver does not remain in it, and some particle of it is also necessary by its very nature. But for one who has to use very much lead at one time, like someone who smelts sweepings or cements, or for someone who wishes to bring his operations to a conclusion and withdraw his investment, it is possible to have the lead again. In order to do this, the litharge is taken and ground. Cupeling hearths are washed in addition to being ground. Then these powders are made into a paste by wetting them with salt water, and they are made into large

Jan 1, 1942