Search Documents

By Walter Kauzmann

EyRing'S general theory of shear rates as a function of the properties of molecular units of flow is outlined and applied to the creep of metals. This theory regards the unit molecular processes involved in the flow of matter as typical chemical reactions requiring an energy of activation in order to proceed. The externally applied stresses are assumed to influence the rate of flow solely by lowering the activation energy for flow in one direction and raising that for flow in the other, owing to the work that is done by or against the external forces in going from the normal to the activated state. The rates of flow in the two directions are then no longer equal arid there is a net, macroscopically observable flow in one direction. This is understood to be the physical basis for the well-known exponential dependence of the creep rate on the stress. The amount by which the activation energy is raised and lowered by a given external stress is directly related to the molecular dimensions of the unit of flow, so that some insight into these call be found from the behavior of the strain rate with changing stress. When Eyring's equation is applied to the flow of ordinary liquids, such as water or benzene, it has been found from the values of the constants required to fit the observed data that the unit molecular process here involves the passage of single molecules by one another. In metallic creep, on the other hand, the unit molecular process is shown probably to involve the shear of rather large blocks of material (100 to 1000 or more atoms on a side). This agrees with present ideas of crystal flow by means of dislocations such as have been presented by Taylor, Oroaan, and Polanyi, as opposed to flow by a mechanism related to that taking place in atomic diffusion. The dimensions of the dislocations are found to depend markedly on the temperature. The questions of why some metals are so much softer than others, the effects of impurities on hardness, the softness of single crystals, and the role of self-diffusion in creep are considered in the light of the theory and it is shown how answers to these questions (and others similar) might be obtained by use of the theory.

Jan 1, 1941

By Walter Kauzmann

EyRing'S general theory of shear rates as a function of the properties of molecular units of flow is outlined and applied to the creep of metals. This theory regards the unit molecular processes involved in the flow of matter as typical chemical reactions requiring an energy of activation in order to proceed. The externally applied stresses are assumed to influence the rate of flow solely by lowering the activation energy for flow in one direction and raising that for flow in the other, owing to the work that is done by or against the external forces in going from the normal to the activated state. The rates of flow in the two directions are then no longer equal arid there is a net, macroscopically observable flow in one direction. This is understood to be the physical basis for the well-known exponential dependence of the creep rate on the stress. The amount by which the activation energy is raised and lowered by a given external stress is directly related to the molecular dimensions of the unit of flow, so that some insight into these call be found from the behavior of the strain rate with changing stress. When Eyring's equation is applied to the flow of ordinary liquids, such as water or benzene, it has been found from the values of the constants required to fit the observed data that the unit molecular process here involves the passage of single molecules by one another. In metallic creep, on the other hand, the unit molecular process is shown probably to involve the shear of rather large blocks of material (100 to 1000 or more atoms on a side). This agrees with present ideas of crystal flow by means of dislocations such as have been presented by Taylor, Oroaan, and Polanyi, as opposed to flow by a mechanism related to that taking place in atomic diffusion. The dimensions of the dislocations are found to depend markedly on the temperature. The questions of why some metals are so much softer than others, the effects of impurities on hardness, the softness of single crystals, and the role of self-diffusion in creep are considered in the light of the theory and it is shown how answers to these questions (and others similar) might be obtained by use of the theory.

Jan 1, 1941

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove' In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By R. W. Baldwin

On page 309, column 1, the second equation should read: Ma-M1 = dlog_Pa M2-M1 d log P2

Jan 1, 1961

By Walter Kauzman

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications.1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By H. J. Polta, R. W. Michelson

Discounted cash flow analysis is commonly used to evaluate the profit making potential of a business venture. The same method can be used to analyze the effects of varying physical and economic conditions upon the real cost of supplying a mineral commodity. If a fixed rate of return on a capital investment is specified, and the flow of cash, discounted at that rate, is just adequate to repay the investment over the life of the venture, the net present value of the venture is zero. At this condition it is possible to evaluate the unit cost of producing the mineral. It will be exactly equal to the selling price required to calculate a zero present value. Increasing a particular cost factor will not always increase the cost of supply by the same amount. For example, in iron production from magnetic taconite, an increased cost per ton associated with beneficiation would be integrated into the discounted cash flow model along with local, State, and Federal taxes, depletion and depreciation allowances, resultant increased unit recoveries, and all of the other related component cost factors. Rather than adding to the cost, the factor may have a positive, instead of a negative, effect on the discounted cash flow and cause a decreased cost of supply. This value can be determined by a computer model which iterates the necessary selling price until the net present value is essentially zero. The discounted cash flow evaluation model lends itself particularly well to an application of the Monte Carlo simulation method for calculating a probability distribution of iron unit cost resulting from the probability distributions of the component cost factors.

Jan 1, 1969

By Michael Hoch

The phase diagrams of binary systems of some of the transition elements of Groups IV, V, and VI were used to compute the partial free energies of these elements and the free energy of formation of their Laves-type compounds. From these data, isothermal sections of ternary phase diagrams were calculated and compared with experimental results. DURING the investigation of ternary and quaternary high temperature systems formed by the transition elements of Groups IV, V and VI, the binary phase diagrams for these elements available in the literature were studied. In this study, the free energies of formation of the compounds formed in these binary systems were calculated; these values were then used to determine the general shape of the ternary and quaternary phase diagrams. Above 900°C, the transition elements of Groups IV, V, and VI are all bcc and form only Laves-type compounds in binary systems. The investigation was based on the binary phase diagrams published by Hansen.1 The Cr-Nb system was constructed from the data of Elyutin and Funke.' Several unpublished phase diagrams were taken from Schmidt'sLo and English'sl1 compilations. THE BINARY SYSTEMS valuations of the Thermodynamic Functions. Rostokers evaluated the boundaries of the (a + b) field in Ti-base alloys with a two-constant equation. The authors' interest is mainly in the center of the diagrams; therefore the miscibility gaps in the Zr-Nb, W-Cr, Ta-Zr, Ta-Hf, and Ti-W systems were used to evaluate the thermodynamic behavior of the binary systems. Lumsden's4 Equations 29.2, 32.1, and 33.1, page 287, were used for the excess integral free energy FeX, and for the excess partial free energies Fx and replaces b and b replacesP in Lumsden's notation):

Jan 1, 1962

By Frederick Laist

(Butte Meeting, August; 1913.) WHILE remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the -treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was, decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the MacDougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide.

Jan 7, 1913

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By Frederick Laist

(Butte Meeting, August, 1913.) WHILE remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the MacDougall type, specially adapted to the work of roasting for leaching; two leaching tanks, .32 ft. in diameter by 12 ft, deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation ; for example, by electrolysis and by hydrogen sulphide.

Jan 7, 1913

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Lead cake, a zinc smelter flue dust residue, consists primarily of lead sulfate. Characteristic properties of lead cake were determined in order to aid the understanding of reaction mechanisms involved in bismuth removal from lead cake by sulfuric acid digestion. Sp gr (specific gravity) measurements, surface area measurements, and photomicrographs revealed that the particles of lead cake are quite porous and seem to consist of an agglomeration of submicron grains (0.4 pm) fused together in a manner similar to cement clinker. Analysis of experimental rate data, which was independent of particle size, indicates that the dissolution reaction involves two distinct, rate limiting steps. The initial stage of reaction appears to be limited mainly by intergranular diffusion of the reactant, hydrogen ion, while the latter stage of reaction appears to be controlled by diffusion of soluble reaction products through the reaction product layer of the individual grains.

Jan 1, 1979

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By H. S. Hanna, C. Rampacek

The problems and limitations encountered in the Physical beneficiation of the Appalachian Red Iron Ores are discussed. Two major problems are identified - the high phosphorus content and the fine dissemination or encapsulation of mineral impurities in the iron-bearing minerals. A process that combined extreme fine grinding techniques with magnetizing roasting or flotation-separation methods is suggested. By these methods, concentrates assaying 60-61 % Fe, exceeding the widely accepted upper limit of 56% Fe set for these ores, were produced with 75-90% iron recovery. Moreover, it was shown that the phosphorus content of these concentrates could be reduced from 0.25% to 0.03% phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1983

The Palabora ore consists of two types, a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. The latter type also contains substantial quantities of phosphate. These two ore types are separately crushed and are kept separate through copper flotation and magnetic separation, for recovery of magnetite, with the low Ti magnetite being shipped as iron ore. High phosphate tailings are pumped to Foskor, a government-owned phosphate plant nearby. The Palabora plant was originally designed in 1966 for 33, 000 tpd using two 54 in. by 74 in. Allis -Chalmers gyratories; two 7 ft (2. 13 m) standards; four 7 ft shortheads; and six grinding lines, each using one 1,200 hp rod mill and two 1,200 hp ball mills. A fifth short- head and one more grinding line were added later; and with flowsheet improvements, the capacity of the plant was increased to 59, 500 stpd. A further plant expansion involving a third 54 in. primary and two 32 ft by 15 ft (9.75 by 4.6 m) 9,000 hp autogenous mills and another flotation section will bring its capacity to 87,500 stpd in 1977. These two fully autogenous mills are constructed entirely out of doors near the primary crusher, and the ground ore will be pumped a mile to the concentrator by a five-stage pumping system. The Palabora ore is mined with 6, 10, and 12 7d (4.6, 7.6, and 9. 2 cu m) shovels and hauled to the crushers in 110 and 165 st trucks. Sixty-five ton trucks were originally used, but the crusher dump pockets were designed for larger units. Dump pockets, crushers, feeders, and take- away belts are offset in order to keep the two ore types separate. Centerlines of the crushers are only 43 ft (13. 1 m) apart; but, because of their being offset, maintenance room is ample. Initially, more carbonatite ore than foskorite was mined; but as the pit has deepened, this ratio has been reversed. The Palabora ore breaks in the pit with a large amount of oversize boulders; and, with the use of larger trucks, a splitter has been installed on one side of each dump pocket to protect the crusher spider. Smaller trucks dump on the opposite side. To accomodate the splitter, the pocket edge has been raised one meter and moved back one meter. Dust is collected through a special vent shaft between the crushers and the mantle relining area; but even so, two high-pressure water spray headers with nozzles are installed under the edge of the pocket at each dumping position. While only one truck dumps at a time, sprays from all four headers are used to suppress dust. Any leakage of water through the seal around the upper bowl of the crusher is caught by a circular trough under the seal and directed to a sump pump. At this point, there

Jan 1, 1978

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961

By F. W. Osterwald, C. R. Dunrud

Coal mine bumps are a serious hazard to life and property in the mines of east-central Utah. Research into geologic factors associated with these bumps indicates that the bumps are spatially and genetically related to structural and stratigraphic features. Some bumps are directly related to stress accumulation along faults, either from natural causes or as a result of mining. Frictional properties of bedding planes between coal and roof rock, and between some rock units within the roof, directly affect the deformation of coal ribs, and hence the incidence of bumps. These frictional properties are related to the lithology of the roof rocks as well as to the sedimentary structures within the rocks. Commonly a sequence consisting of 1/3 ft of carbonaceous silt-stone, about 2/3 ft of rider coal, and several ft of massive siltstone or sandstone overlies the main seam. The sequence causes difficult roof conditions in the mines, difficult mining conditions and, directly or indirectly, many bumps. The U. S. Geological Survey has studied the relationships between geological features and coal mine bumps at Sunnyside, Utah, for about six years. The work, which was originally undertaken at the request of and in cooperation with the U.S. Bureau of

Jan 1, 1965

By V. I. Purcell, S. C. Sun. R. E. Snow

A study including effects of 7) pH value, 2) fatty acid collector, 3) fuel oil, 4) interfering ion, 5) particle size, and 6) operational variables. Test results indicate feasibility of fatty acid flotation under certain restrictive conditions. FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in Florida."= The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo-wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being predominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon. Experimental Procedures: After being dried to less than 1 pct surface moisture the material was dry-ground in a Hardinge conical ball mill to —6 mesh. The ground product was classified into 6/20, 20/200, and —200 mesh size fractions. On the basis of Table I, the coarse and fine size fractions were considered as phosphate concentrates, because of their high phosphorus contents. In contrast, the 20/200 mesh fraction, which was low in phosphorus, was used as the flotation feed. All the flotation tests, unless otherwise stated, were performed in a laboratory Fagergren machine under the following conditions: 1) 400 g of solid feed for each test, 2) 2000 rpm impeller speed, 3) 8.9 pH and 4-min conditioning, and 4) 3-min flotation. The procedure used for the quantitative bubble pick-up tests has been described previously.18

Jan 1, 1958