Search Documents

F. E. BACHMAN, Buffalo, N. Y. (Communication to the Secretary) : The investigation so fully described by Mr. Laudig was undertaken with the idea of determining if it is possible to learn by expesiment, without an actual trial in the furnace, what economical results can be expected from the use of a given ore-mixture. The research was necessarily preliminary, and the results obtained are only to be depended upon so far as they relate to the samples treated. With the exception of the ores obtained from the stock-piles of the Buffalo Furnace Company, and several samples taken at a neighboring furnace, there is no certainty that the ores represented the average shipments of any mine. For this reason the publication of the names of the ores might do producers a great injustice. The names of the ores arc therefore withheld, and their identity is further .veiled by leaving out of the analyses the phosphorus-contents. The investigation was begun with the preconceived idea that the rate of reduction would be found to be dependent upon the accessibility of the particles of the ore to the action of the reducing-gas. In other words, a spongy, brown hematite or a very fine Mesabi would be the easiest reduced. I had formed a scale with No. 21 first, No. 30 second, No. 1 third, Nos. 5, 24, 25 and the remaining Mesabis fourth, etc , which is sufficient to show how much actual results differ from a judgment based on physical characteristics. The ore expected to be most easily reduced proved to be 25th in the list, while the one placed

Jan 1, 1897

By Donald M. Liddell, G. C. RIDDELL

THE cosmic ray continues to engage the attention of the physicists, and according to Millikan and Compton, experiments of the past summer indicate that these rays must come from interstellar space, but not from the stars themselves. According to press reports of the International Congress of Physicists at Rome, the view was given there that these rays have an initiating potential of over 750,000.000 volts. In the field of spectrographic investigation great strides have been made. The U. S. Naval Research Laboratories (R. F. Mehl and G. E. Doan of Lehigh) have just finished a year's work with a "radium torch" or "shadowgraphic apparatus" in the field of the X-ray, that bids fair to displace the latter to a great extent. The torch is more powerful., easier to operate and cheaper. Penetration of 10 in. of steel has been accomplished, which. is much -beyond the- -scope-, of the X-ray..

Jan 1, 1932

By B. A. Rogers

IN addition to the usual methods of manufacturing steel, a number of special processes have been the subject of considerable experimentation-and use in manufacturing practice. A number of these methods have been of a type in which a rapid refining action has been secured through the intimate mixture of fluid slag with fluid metal. The persistence with which more rapid methods are sought is indicated by the current interest in the Aston' method for producing wrought iron and in the Perrin2 process for dephosphorizing and deoxidizing steel. In the Perrin process, in particular, the mixing action is extremely vigorous and the reactions proceed with surprising speed.

Jan 1, 1936

By H. Herbert Hughes

ECONOMISTS have predicted that the present business depression ultimately may pay big dividends to industry through the cumulative savings resulting from technical improvements and merchandising advances that might never have been developed under normal conditions. Waste prevention is a sound medicine for economic ills. In theory, this prescription may be applied not' only to raw materials, but also to labor, fuel, over- head, and other phases of production. Actually, how- ever, regardless of the efficiency of operating practices, waste is inevitable in the production of many commodities. The problem then becomes one of profitable utilization of waste rather than prevention.

Jan 1, 1932

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

The following is an incomplete list of members and guests who called at Institute headquarters during the period Jan. 10, 1918 to Feb. 10, 1919. Walter F. E. Barcus. Lt. C. K. McDonald, U. S. N. R. F. Capt. D. H. Bradley, Jr. Major John DeN. Macomb, Bayhead, N. J. Melvis Buigger. - Samuel Melitzer, New York City. Eugene Coste, Calgary, Can. T. C. Merriman, New Haven, Conn. C. W. Cromwell, Warren, Ariz. Wm. J. Millard, Tulsa, Okla. E. O. Daue. Benj. L. Miller, Bethlehem, Pa. Capt. H. W. Edmondson. S. B. Patterson, Jr., Allentown, Pa. E. W. Engelmann, Hayden, Ariz. Lynn L. Pomeroy, New York City. C. Mason Farnham. W. E. Pomeroy, New York City. Lt. C. W. Frith, Salt Lake City, Utah. G. M. Ponton, Ottawa, Ont. John T. Fuller, Honesdale, Pa. Wallace E. Pratt, Ft. Worth, Tex. Walter A. Funk, Idaho Sp., Colo. Harold L. Rau, Milwaukee, Wis. Major W. R. Grunow, New York, N..Y. Lt. E. J. Ristedt, Camp Merritt. A. W. Hackwood, Butte, Mont. George M. Ryall, Los Angeles, Cal. Lt. Nathaniel Herz, New Haven, Conn. D. B. Scott, Mogollon, N. M. Ralph T. Hirsh, New York City., W. H. Staver. O. P. Hood, Washington, D. C. Douglas B. Sterrett, Washington, D. C. E. B. Hopkins, Houston, Tex. J. A. Stewart, Minneapolis, Minn. Hugh C. Ingle, Pensacola, Fla. R. H. Summer, Wilmington, Del. Capt. Wm. F. Jahn. W. G. Swart, Duluth, Minn. Roswell H. -Johnson, Pittsburgh, Pa. Kirby Thomas, New York City. Jesse L. Jones, Pittsburgh. Pa. Capt. H. D. Trounce, San Diego, Cal. Edgar Kidwell, Berkeley, Cal. L. Unger, New York City. .D. H. Ladd, Detroit, Mich. George F. Vivian, Butte, Mont. Raymond B. Ladoo, Cambridge, Mass. R. A. Walter, Reading, Pa. W. H. Landers. Lt. R. G. Wayland, Chehalis, Wash. David Lasner, Elizabeth, N. J. R. J. White, Wallace, Idaho. J. M. Lilligren. J. S. Wroth, Albuquerque, N. M. Lt. Wm. J. Linn, Chicago, Ill. Herbert Hoover, General Pershing, Ambassador William G. Sharp and Admiral William S. Benson were speakers to-day at the annual luncheon in honor of Washington's Birthday, given by the American Club of Paris at the Palais D'Orsay.

Jan 3, 1919

By Louis D. Huntoon

SHORTLY after publication of the article in the July, 1924, issue Of MINING AND METALLURGY, entitled "Canada as a Gold Producer," requests were received to determine the ownership of production. Advices have also been received that considerable discussion has taken place on the same questions both in Canada and Great Britain. The author is indebted to R. H. Coates, Dominion Statistician, and George C. Bateman, Secretary, Ontario Mining Association, for the following figures and takes this opportunity of expressing his appreciation. There have been no statistics compiled as to ownership of production. Statistics were compiled as of Dec. 31, 1921 relative to the distribution of stocks, bonds and "other securi¬ties" in industrials, agriculture excepted, throughout the Dominion, and "distribution of ownership of securities issued by mining companies incorporated and operating in Ontario" for the same year. Stock registration does not necessarily represent actual ownership' as large blocks may be endorsed and not transferred; neither does registration actually represent production. When the charts are studied individually and collectively one cannot help but be impressed with the fact .that in the mineral industry of Ontario and the Dominion at large, Canadian registration predominates, the United States registration is about half that of Canada, and Great Britain is about half that of the United States. When the nickel-copper industry is excepted the British registration falls to a very low percentage. Since Dec. 31, 1921, British capital has commenced to flow into mining enterprises in Ontario and it has been already rewarded by the discovery of valuable ore deposits.

Jan 1, 1925

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By AIME AIME

ON the afternoon of Feb. 20 of this year a new volcano was born in the center of the State of Michoacan, Mexico, about 100 miles inland from the Pacific Coast. Creation of this new mountain - forming crater began on an almost flat cultivated field at the south margin of a small basin about a mile in diameter and having an altitude of approximately 6800 ft. above sea level. This basin is connected to a gently inclined plain that forms the Parangaricutiro valley, the chief town of this municipality, bearing the same name as the valley, being situated three miles from the site of the new crater. The village of Paracutin, from which the new volcano received its name, is about one mile to the northwest of the crater. From the City of Mexico to the volcano is a distance of 330 miles. The paved highway running from Mexico City to Guadalajara, by way of Toluca and Morelia, is left at Carapan; from here another paved branch highway goes to Uruapan. The town of Paracutin is reached by a narrow dirt road 18 miles from Uruapan and connects with a road leading to Parangaricutiro where horses may be hired for a 40-minute trip to a place where visitors can enjoy a magnificent view of the volcano. It is possible to get within half a mile of the point of eruption in this manner.

Jan 1, 1943

By AIME AIME

OCTOBER will be western month for the Institute. With meetings at Spokane, Tulsa, Los Angeles, and San Francisco, and with a large number of American Institute of Mining Engineers members and their families in the party sailing out through the Golden Gate to Japan on the afternoon of the tenth, the major activities of the Institute will, for this month at least, be west of the Mississippi. Despite cancellations due to necessity, most of the officers of the Institute will be present and taking part in some one or more of the Western meetings. Prof. Robert S. Richards, our senior past-president, will attend both the Spokane and San Francisco meetings and then go to Japan. President Bradley will preside at the San Francisco meeting and then head the party going to Tokyo. At Tulsa and Los Angeles, the principal officers of the Petroleum Division will be present and active and at all the meetings, directors, ex-directors and -present and past officers will be on the job and keeping things moving.

Jan 1, 1929

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By J. L. Workman

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. The Putman Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 million tpy operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1969

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By C. M. Loeb, A. M. Gaudin, J. H. Brown

R. E. Carter (General Research Laboratory, Schenec-tady, N. Y.)—Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crys-tallographic directions, and in materials containing quartz because of the a-p' transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 1, 1960

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By F. Wald, A. J. Rosenberg

The general features of the constitution of the B-Pt system were determined using standard rnetal-lograph~c, thermoanalytic, and X-ray diffraction techniques. Three compound were found. Two of these, Pt3B and Pt,B, are formed by peritectic reactions at 523° and 890°C, respectively. The third, Pt3B,, is congruently melting with a flat maximum at 940°C but decomposes eutectoidally in to Pt,B ant1 boron nt - 600° to 650°C. THE low-temperature allomorph of boron (red, simple rhombohedra1 a boron) is of scientific and technological interest as an elemental semiconductor.' However, the studies of this material have been hampered by its reported instability above 1200"~ which precludes crystal growth from the melt (mp - 2200°C). Crystallization from platinum solutions has been suggested as an alternative crystal-growth technique, but has met with only limited success.' The technique depends upon the existence of a significant difference between the eutectic temperature and the transformation temperature of boron. In order to clarify the conditions for further crystal-growth experiments, we found it desirable to redetermine the main features of the B-Pt phase diagram since previous reports on the system1'5'6'7 are in marked disagreement. EXPERIMENTAL The experimental methods used were thermal analysis, metallography, X-ray analysis, and, to a lesser extent, measurements of microhardness. Most of the alloys were prepared from spectrograph-ically standardized boron obtained from Johnson-Matthey &Co., Ltd. (212 ppm impurities, exclusive of carbon and oxygen) and platinum powder obtained from F. Bishop & Co. (200 ppm impurities, mainly of other platinum group metals). Some alloys were also prepared with very high-purity, float-zone refined boron (99.9999 pct obtained from "Wacker Chemie" and extrahigh-purity platinum (99.999 pct) obtained from Johnson-Matthey & Co., Ltd. The reported results did not depend on the choices of these starting materials. Five-gram alloy specimens containing 10, 20, 25, 27.5, 30, 33.3, 34, 35, 37, 37.5, 38, 39, 40, 41, 42, 43, 45, 50, 55, 60, 70, and 80 at. pct B were made by melting the elements together in boron nitride crucibles using rf heating of a graphite susceptor, either in vacuum or under high-purity argon. All alloys were heated to at least 1800°C for -5 to 15 min. Most of the alloys did not wet the crucibles when the latter were outgassed by preheating under vacuum. In any event, no weight loss was detected after melting, and the nominal composition was assumed for all specimens. Thermal analysis on 2.5-g samples were carried out in boron-nitride crucibles under a vacuum of 5 x X torr. The apparatus was heated in a "Kan-thal A 1" wound furnace, which limited the maximum temperature to about 1100°C. The output of the indicator thermocouple was fed to a dc recorder with a 1-mv full-scale span and an adjustable zero. The apparatus was calibrated repeatedly, using the freezing points of high-purity aluminum, silver, and gold. The results justified the use of the NBS voltage vs temperature tables for Pt/Pt 10 pct Rh thermocouples. All thermal analyses were run at least twice and both the heating and cooling effects were recorded. Most of the alloys had a very strong tendency to supercool. However, the use of mechanical vibration permitted reproducibility within *5°C for all alloys, except in the region around 40 at. pct B. Only the cooling effects are plotted in Fig. 2, since they appear to be more reliable. For metallography, the alloys were cut with a diamond cutting wheel, cast in a polymethacrylate resin, ground and polished with diamond paste, and etched with dilute aqua regia, a common etch for platinum alloys. Both copper and molybdenum radiation were employed to obtain X-ray diffraction data using Debye-Scherrer cameras and a "Norelco" diffractometer Diffractometry with high scanning speeds (1 deg per min) using nickel filtered CuK, radiation was used to identify the main regions of the diagram. However, molybdenum radiation was used for the detection of boron, since the latter showed very strong absorption and fluorescence effects with CuK, radiation. RESULTS AND DISCUSSION Three intermediate compounds, corresponding to the compositions Pt3B, Pt2B, and Pt3B2, were found in the system. Fig. 1 reproduces their X-ray diffraction spectra, together with those of pure boron and pure platinum. As can be seen from the thermal-analysis data in Fig. 2, Pt3B and Pt2B are formed by

Jan 1, 1965

By Jean Bonnemaison

Societe Miniere & Metallurgique de Penarroya Noyelles-Godault works are located in the northern part of France. The complex includes a lead smelter, a zinc smelter, shops for production of manufactured products and all necessary general services. The zinc smelting complex described in this paper was designed in 1959 to replace an old horizontal retort distillation furnace and was first operated in May 1962. It includes: - a sinter plant producing the zinc sinter for the Imperial Smelting furnace : zinc, lead and bulk zinc-lead concentrates are sintered on a Dwight-Lloyd machine with a working area of 80 sq.m. Cadmium sludges are treated by the wet method in a separate plant for recovery of cadmium. Sulphur dioxide contained in gases goes to a gas washing tower and is subsequently made into sulphuric acid in a plant with a capacity of 550 m.t. per day. - a smelting plant where the process developed by Imperial Smelting Processes Ltd. is applied : the blast furnace which was modified in 1967 has an area of 17.5 sq.m. at the tuyeres level and a section of 24 sq.m. at the top of the shaft. It has a theoretical zinc capacity of 100,000 m.t. per annum. Air blast is heated by means of covers up to the theoretical temperature of 950ºC. Zinc produced is either directly cast into slabs for sale as standard 'good ordinary brand' zinc, or sent to a refining plant where the New Jersey process designed to produce 'special high grade' zinc is in application. Mixes of zinc containing various amounts of lead, cadmium or aluminum are prepared to customer specification in a mixing plant.

Jan 1, 1970

By Ralph A. Sherman

In these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home. Factors That Govern the Choice of Fuel and Burning Equipment A rational, intelligent selection of fuel and equipment for heating the home would consider two groups of factors: Cost Factors Convenience Factors 1. Cost of potential heat in fuel 1. Attention 2. Efficiency of combustion and heat transfer 2. Dirt 3. Fixed charges 3. Noise a. Interest b. Depreciation c. Repairs 4. Power costs 5. Cost of handling ash and refuse. As just stated, the purpose of this paper is to analyze the relative importance of the five cost factors and not to discuss particularly the relative total costs of different methods of heating. However, to arrive at the percentage costs and to show clearly how they were determined, a statement of the total costs is unavoidable. One example only will

Jan 1, 1934