Search Documents

By C. Schlumberger, M. Schlumberger

In order to explore electrically a terrain composed of a succession of horizontal beds, a current of known intensity i is caused to flow between two grounds A and B, and the resultant drop of potential , caused by the resistance of the earth, is measured between two given points in the soil, M and N. In practice it is convenient to choose the two points M and N so that they lie on the line AB and their midpoint coincides with the middle 0, of that line, although this is not imperative. When the lengths L and I of the two lines AB and MN are varied, equations are obtained which may be solved for the resistivity p of the subsoil at various depths. Recall briefly that the formula 4 x l gives the average resistivity, in the horizontal direction, of a layer of earth which extends to a depth1 about equal to L/4. This elementary concept is adequate for numerous practical applications. Nevertheless, it must be said that, in many cases, a rigorous mathematical analysis may be made, provided it is always a question of homogeneous, superposed horizontal beds. The authors expect to publish, later on, appropriate methods of calculation for some specific cases.

Jan 1, 1932

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

By G. Gutierrez, M. C. Fuerstenau, J. D. Miller

The response of pure goethite and two natural iron ores to flotation with potassium octyl hydroxamate is presented. The ores contained 12.5% and 39.7% iron; concentrates containing 69.5% and 61.5% iron, respectively, were obtained with additions of 0.4 lb/ton hydroxamate. Selective flotation of iron oxides from associated gangue minerals has proven difficult in the past with standard collectors, such as sulfonates and fatty acids. As a result, recent work has been directed toward silica flotation with calcium activation after the iron oxide surfaces have been blinded with certain starches.& The results obtained with this technique are encouraging. This method, however, involves depressing a mineral that would normally float under the conditions employed. A preferable method would involve floating the iron oxide because quartz is naturally depressed until activated. Earlier work involved this approach, but in view of the results obtained, collectors that exhibit greater specificity for iron are needed. During an investigation of chrysocolla flotation with potassium octyl hydroxamate, a metal chelate former, it was observed that pyrite floated well with low additions of collector.3 This phenomenon suggests that hydroxamate has a rather strong affinity for iron, and that other iron-bearing minerals should also respond to flotation with octyl hydroxamate. The object of this paper is to determine this response. The experimental work was divided into areas, the first of which involved microflotation experiments with pure goethite with an apparatus described previously.4 Goethite was selected because of the ease

Jan 1, 1968

Frontino operates three underground lode mines at Segovia in the area of northwest Antioquia, Colombia, which has been an important gold producing district since the late 1800s. Auriferous pyrite, the pre-dominent sulfide, carries very finely disseminated gold. Other minor sulfides are galena, pyrrhotite, and sphalerite in quartz gangue with the host rock being granodiorite. Silver is associated with the galena and also occurs as a sulfo-salt. In 1.973 and 1974, at an annual milling rate of 145,000 mt (160,000 st), average mill heads were 7.80 g per mt (0.23 oz per st) Au; 20.0 g per mt (0.58 oz per st) Ag; and 0.37% Pb; with a production of 1,150 kg (35,700 oz) Au and 4,500 kg (141,000 oz) Ag. Over 300 mt (330 st) of Pb concentrate were shipped. The ore is crushed to minus 16 mm (5 18 in. ) and fed to a rod mill with the discharge passing over a 1.07 m by 1.07 m (42 in. by 42 in. ) jig operating in closed circuit with the underflow from a cyclone in closed circuit with two ball mills. Cyclone overflow is bulk-floated for sulfide recovery from which the tailings are sent to the river as waste with the flotation concentrate joining the jig concentrate for cyanidation. The combined gold bearing concentrates, after cyclone classification, are reground to a very fine mesh in closed circuit with cyclone classification, with the overflow going to the primary thickener. Regrinding, classification, and thickening is done in cyanide solution, and the primary thickener produces a pregnant solution for Merrill -Crowe precipitation. The thickener underflow is the feed to the agitators, thickener, and filter from which the overflow and filtrate are sent to precipitation. The washed filter cake is repulped and floated for the recovery of a galena concentrate for shipment. About 40% of the recovered silver is in this concentrate. In the refinery the precipitate is melted into a dore bullion. This 600 mt (660 st) capacity mill employs several interesting techniques. Gold recovery of 85% to 90% from a complex sulfide denotes good practice. While total power at 42 kwh per mt (46 kwh per st) is high, it would be recognized that the grinding units are small in size and the flowsheet is complicated due to the gold occurring in the sulfide minerals. The extremely low-cost electric power is generated by

Jan 1, 1981

By P. E. Arnold, G. S. Ansell

RELAXATION in metals has been studied in detail by many workers in recent years.1-5 These studies have shown that there is an energy-loss peak observed in a metal placed in mechanical resonance at low frequencies which may be correlated with various metallurgical processes. These experiments have been largely used to study single-phase materials. In order to study the effect of a finely dispersed second phase in a metal matrix upon this phenomenon, the relaxation behavior of an aluminum-aluminum oxide SAP-Type alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions was investigated by the use of internal-friction measurements. The alloys studied, designated MD 2100, consist of a matrix of commercial-purity aluminum containing a finely dispersed second phase of aluminum oxide. The aluminum oxide is present in this alloy in the form of fine platelets approximately 130A units thick and several microns on edge. The mean free path betwen dispersed platelets is approximately 0.5 p. The grain size of this alloy is extremely stable at temperatures as high as the melting temperature of the aluminum matrix. In the as-extruded condition the grain diameter is several microns, while in the recrystallized condition it is several millimeters in diameter. The damping characteristics of the alloy samples were determined using a torsional-pendulum device. The internal-friction constant was determined for this alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions over the temperature range from 343" to 923°K at frequencies of 0.9, 1.3, and 1.8 cycles per sec. An internal-friction peak was observed in testing the fine-grained alloys which was not observed for the coarse-grained alloys. This peak, which might be associated with a type of grain-boundary relaxation, was observed at each of the three different test frequencies for the fine-grained sample. The temperature at which the relaxation peak occurred for each of the three different frequencies is shown in Table I. From these data an activation energy of relaxation for each pair of frequencies was determined by comparing the temperature shift of the relaxation peak with frequency between each of the test frequencies, assuming that an Arrhenius-type rate equation is applicable. The activation energy of relaxation determined from these data is also shown in Table I. The mean value of the activation energy was about 6 kcal per mole. The activation energy for the relaxation process determined in this investigation indicates that the relaxation associated with the grain boundaries in this aluminum-aluminum oxide SAP-Type alloy is quite a different process than grain boundary relaxation in single-phase aluminum alloys. In these latter alloys, the activation energy for relaxation has been found to be the activation energy for self-diffusion, approximately 36 kcal per mole1,2 Where the activation energy is the same as the activation energy for self diffusion, it has been proposed that the relaxation phenomena is dependent upon vacancy formation and motion. It is apparent therefore, that, in this aluminum-aluminum oxide SAP-Type alloy, the relaxation must be due to another type of atom transport. It has been shown previously in studies of the high-temperature, low-stress, steady-state creep behavior of as-extruded aluminum SAP-Type alloys, that the activation energy for steady-state creep is one that may be characterized by the nucleation of dislocations from the grain boundaries. It is proposed that the relaxation behavior observed here is due to a similar effect. In this case, the internal-friction peak is a resonance behavior due to the time-dependent nucleation of dislocations from grain boundaries in the sample. A process of this type would have an activation energy which is undoubtedly stress-dependent and of the form Q = Q, + (dQ/du)u

Jan 1, 1962

By C. W. Macgregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By C. W. MacGregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By J. H. Nead

Discussion of the paper of J. H. NEAD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2341 to 2357. E. D. CAMPBELL, Ann Arbor, Mich.-Any one at all familar with research work can at once see that Mr. Nead has condensed into his tables and curves the results of a carefully planned set of experiments which must have involved a great amount of work on his part. He deserves much credit for the way in which he has carried out these experiments, for it is to the results of such systematic experimentation that we must look for further knowledge of the underlying causes which determine the physical properties of steel. It will probably be many years before we have sufficient knowledge of all the factors of the problem of the constitution of steel, but every set of carefully carried out experiments such as Mr. Nead has made adds something to our knowledge and brings us a little nearer to the final solution of the problem.

Jan 5, 1916

AN UNUSUAL OPPORTUNITY FOR INSTITUTE MEMBERS to increase or complete their sets of the Transactions. In order to encourage the custom of members increasing each year the number of Volumes of the Transactions in their private libraries until the sets are complete, the Board of Directors has authorized the sale of Transactions previous to the year 1913 at the following greatly reduced rates. This offer is made effective for sales made only during the year 1914, and applies only to members in good standing, and to libraries. The reduced price automatically ceases to apply to any volume when the total number of such volume left in stock is reduced to fifty (50).

Jan 12, 1913

By William H. Shockley

Though China has been widely explored by mining engineers during the past dozen years, comparatively little has been published concerning its mineral resources. The few moilographs scattered through the transactions of various societies contain far less information than the private reports made to the numerous syndicates which have sent out engineers. The best general account of the geolopy and mineral resources of China is to be found in the works of von Richthofen,' a remarkably gifted observer. The observations recorded here in this paper were made in the service of the Pekin Syndicate (which has kindly given me permission to publish them), during the first months of 1898, among the coal- and iron-fields of southeastern Shansi. This is one of the largest anthracite-regions known, the area being

Jan 1, 1904

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By B. H. Bergstram, C. L. Sollenberger

When glass spheres are crushed by slow compression loading, the outer lune-shaped fragments resulting from the fracture consistently fly outward at high velocity. About 45 pct of the strain energy fed into the sphere-platen system reappears in the form of the kinetic energy possessed by these fragments. These measurements were obtained from high-speed photographs. This kinetic energy can be utilized for addtional comminution if the fragments are allowed to impact against a suitable structure. Comminution theory has advanced considerably in recent years by the study of this unit operation under laboratory conditions. Some of the parameters have been isolated, but the experimental measurements of the pertinent quantities, such as energy, particle size, etc., are still only made prior to and after the conclusion of a fracture sequence. The catastrophic fracture process itself has not been adequately studied from a comminution point of view. It has recently been suggested by Gilvarry that the fragments which result from the free crushing of a single glass sphere by slow compression contain a considerable amount of kinetic energy after fracture. This kinetic energy, if properly directed, possibly can be partially utilized to cause additional fracture. In this paper a hypothesis will be presented which suggests that this kinetic energy is necessarily present and that its dissipation is the process by which a large part of the thermal energy imparted to the crushed product is generated. Evidence supporting the existence of kinetic energy and its utilization for secondary fracture will also be presented. THEORETICAL A previous paper4 has shown that the load-deformation curve of a system composed of an elastic sphere gripped by a pair of parallel platens, can be predicted by a consideration of the theories of Hertz as summarized by Timoshenko.' The deformation A, of one half of the system is given by which states that the deformation is a function of the mutually applied load, P, the radius of the sphere, R; and the respective physical properties of Poisson's ratio, v, and Young's modulus of elasticity, Y. The shape of experimental load-deformation curves conform to this relationship. The energy input to the sphere-platen system, can be predicted from the integral of the load acting through the appropriate distance, dA. Since dA can be evaluated in terms of P from the derivative of Eq. 1, this integral can be integrated between limits of 0 and P. The test sphere, however, is loaded at not one but at two points of contact, i.e., at both ends of a diameter, and hence the total energy input, E, is twice the energy input at each end, or The energy input to the system calculated from this equation corresponds to the energy computed from the measured area under the load-deformation curve. Timoshenko, considering the impact of two perfectly elastic spheres, has shown that the inter-penetration distance A is given by - m f (D (^ * ^t w as modified for the special case where one sphere is of infinite radius, i.e., its surface is a plane; where M is the mass of the finite sphere of radius R, and V is the velocity of approach at the start of an impact and also equals the final velocity of separation for perfectly elastic bodies. Because A is also a function of the load and the elastic properties, as shown in Eq. 1, the velocity, V, can also be calculated in terms of the elastic properties and maximum load, P, or

Jan 1, 1961

By William Kent

William Kent, Pi.~t~bIJrQh, Pa.: The steel rnanufac.tnret of this country nlust ever he grateful to Dr. Dudley for his painstaking and conscientious endeavor to estaldish the relation between the chemical analysis and the wearing capcity of steel rails. They tnust thank him for the vast array of $acts he presents, and for having given them sixty-four analyses with which to combat his own conclusions and to establish their own, which are entirely opposite to his. In Dr. Duclley" discussion of his former investigation, at the Pittsburgh meeting, he said, "If you do not like my conclusions, draw your own conclusions." I have studied his last paper as thoroughly as the limited time since I received it would adruit, and have drawn some concluvions which I will first state, and then attempt to demonstrate. Briefly stated, my conclusions are: lst, That as far as these 64 analyses reveal anything of service to railmakers and cotsumera, it is that within the following chemical and physical limits, viz., Carbon,..0.20 to 0.60 Pisovphorue ,..0.026 to 0.146 Silicon,.. 0015 to 0.480 BInnganese.......0.262 to 0 880 Phosl~horus un~ts,..20.3 to 6.72 Bending weight,. 2270 lbs. to 4260 Ibs. Drfl~ctinn,.. 13O to 190° or in other words within the limits of rienrly the whole range of the chenlical and bending testa of these 6-2 mils: the wearing capacity bears no relation at all to mrbon, to phosphorus, to silicon, to mnnganese, to phosphorus units, to bending weight or to deflection or if there is any relation between the wearing capacity and thest! six or sr!ven variables, it is so obscured by the action of other cause or variat~les not yet known, that such relation cannot be expressed by any practical formula. 2d. That the difference in wearing capacity of these 64 rails was not due to unrbon, to phosphorus, to silicou, to manganese, or to anj combinntion of these four elements, but that it was due to some other cause or cornbination of causes, of which Dr. Dudley's whole iuvestigtion furnishes 11s no clue whatever. A few of the nlarry possible causes I lnay name : sulphur, copper, oxide of iron inclossl air or other gases, orerblowing, underblowing, oyrhaiting, undcrIreatinp, too hot-finishing, too cold-finishing, cold-straightening, toc great or too litkle rductiun hlu the rail to the ingot, or the portion

Jan 1, 1881

By W. L. Zeigler

The mill is a departure from gravity concentration and has gained a reputation for the low initial cost of erection, extreme simplicity and the low cost of milling on the refractory character of the ore which is treated. The structure is of heavy timbers with board walls and corrugated roofing. The floors are concrete and the general layout is of the ground floor only. All the machines are driven by individual motors and the transmission usually found in such a plant is entirely absent. (Fig. 2.) ORE The ore from the Galena mine is sheared Wallace quartzite replaced with quartz, siderite, pyrite, sphalerite, gray copper (tetrahedrite) and very fine-grained argentiferous galena. Much of the silver is undoubtedly associated with the gray copper, the amount, however, apparently varies with different localities in the vein. An average assay of the ore is 6.0 per cent. lead, 1.3 per cent. zinc, 0.3 per cent. copper, 17.5 per cent. iron and 4.5 oz. silver. The concentrates produced are of an average 53 per cent. lead, 40 oz. silver, 8 per cent. zinc and 11 per cent. iron, while the tailings are 0.5 per cent. lead, 0.4 oz. silver. With the present market for zinc no attempt is made to produce a zinc concentrate.

Jan 1, 1927

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

Jan 1, 1967

By Yves Dardel

INTRODUCTION SINCE the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts,2 then Baukloh and Oesterlen,3 during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreau,4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per 100 g of metal. Winterhager,5 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitz6 as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhauser8 extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per 100 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per 100 g, while that of the usual apparatus was only about 0.2 cm3 per 100 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. [ ] Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of Eborall and Ransley, as well as the earlier apparatus,

Jan 1, 1948