Search Documents

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nev. The supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45' to a slope angle that started at 45° on the south wall, and gradually increased to 575' at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 ft to about 550 ft. About 2.55 million tons of waste and ore were removed by stripping and mining. Measurements made between November 1965 and September 1967 showed that the pit wall was stable before excavation began, that changes in the measured quantities occurred in the pit wall during the excavation, and that the wall returned to a condition of equilibrium after the mining was completed. The need for a method and the technology to pre-design a pit slope does not require elaboration. About 5 billion tons of material are excavated yearly by surface mining methods in the United States, and the economics, safety, and availability of lower grade metals, nonmetals and fuels could all be substantially improved if operators could preselect optimum slope angles. Mining companies and the Bureau of Mines have recognized the need for developing engineering methods to determine stable slope angles. In the industry, Kennecott Copper Corp. had been making an

Jan 1, 1969

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to Villa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

By Douglas R. Shaw

Normal dodecyl mercaptan was evaluated as a collector for flotation of sulfide minerals and precious metals. The reagent is from the class of normal mercaptoalkanes (n-alkyl thiols), and is commercially available in the form of a mixture of n-dodecyl mercaptan, the primary constituent, and a water-soluble dispersant, under the trade name Pennfloat™ 3. * Reported are results of bench-scale flotation experiments on many commercially treated base metal and precious metal sulfide ores. Dosages, points of addition, and flotation pH were among the variables studied. Most notable results were increased copper, molybdenum, and precious metals recoveries. Dosages of dodecyl mercaptan on some ores were considerably lower than required for conventional collectors. The reagent was shown to be a highly effective and versatile collector on virtually all of the more than 30 sulfide ore types examined.

Jan 1, 1982

By Tomoyuki Moritani, Atsuyuki Mizuno

A concentration of manganese nodule varies areally from 0 to 30 kg/m2 in the central-eastern deep sea bottom of Central Pacific Basin with depth of 5,600-5,900m, but generally it is low, mostly of the abundance order from 0 to less than some kilograms per square metres through the bottom. A high concentration over about l0kg/m is localized to the northwestern basin, besides "St. 414 Deep Sea Hill" and “GH 76-1 Trought”, and also it is likely related with the substratum of deep sea clay. Nodules are tentatively classified into nine types of Sr, SPr, SEr, Db, Ss/SPs, ISs, IDPs and V, in terms of morphology and surface feature. The types may be related with internal structure, nuculeus, mineral composition, chemical composition, occurrence and areal distribution, and might have resulted from various environmental factors of nodule genesis. The abundance of nodule at each station shows the interesting relation with acoustic records by 3.5KHz and seismic reflection profilings. In both the records, thick transparent layer over about 45m thick yield neither any nor significant amount of nodule. The layer less than 45m relates with abundant nodules up to 30kg/m2, though it yield also very little nodule in some cases. The relation suggests that the formation of nodule most likely could be related with the accumulation rate of the post-middle Eocene sedimentary sequence to some extent and also with other controlling factors. The relation can lead us to the tentative delineation of distribution of nodule deposits in the area. The comparative-consideration with the deposits in GH 74-5 area, just east- ward of the present area, shows the areal peculiarity of nodule genesis in deep sea bottom. The results of chemical analyses will be discussed elsewhere.

Jan 1, 1976

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor counties is due to the influence of what is known as the Cisco Arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across Archer County. It has been impossible for the authors to isolate the statistics for production for each of the many small pools of this district, as such statistics are not kept by the operators except for the district as a whole, therefore Tables 1 and 2 are comparatively short. The number of wells

Jan 1, 1935

By Milton E. Wadsworth

Hydrometallurgical processing of ore deposits by solution mining or in situ techniques requires the interfacing of technologies as diverse as hydrology, geology, chemistry, and rubblization. This synthesis represents one of the main challenges to in situ processing due to the inherent complexity and vocabulary of these well-developed technologies, and to the general lack of appreciation for the depth of knowledge and endeavor in each separate field. No better example of the need for such interfacing of technologies exists than that of solution mining. How well these technologies interface depends upon the size of the operation and its financial capability to use the information and technology available. It is inconceivable that any one individual can optimize each potential contribution alone; consequently, some areas are usually neglected or simply are not fully appreciated. When one examines what must be done at a future date to develop and exploit a remote solution mining system, it becomes obvious that each discipline must effectively communicate the needed background information to make the project a synthesized whole.

Jan 12, 1977

By Eugene Guccione

FOREWORD-At the SME-AIME meeting in Las Vegas this year, the SME Publications Board and the MINING ENGINEERING Committee decided that a fitting way of celebrating the United States' bicentennial would be to publish an article in ME covering the great men in American mining. After some discussion as to the inclusion of financiers -men such as William Randolph Hearst, J. Pierpont Morgan, etc.-the group agreed that the feature should be restricted to the "nuts-and-bolt people," e.g., mining engineers, geologists, mineral processing engineers. Thus, from the AIME All Institute Honors roll and from the SME Awards list, the group chose these 11 historical figures: Herbert Hoover, Daniel C. Jackling, Henry Krumb, James Douglas, Rossiter W. Raymond, Hal W. Hardinge, Seeley W. Mudd, Erskine Ramsay, Howard N. Eavenson, Robert A. Richards, Arthur F. Taggart. What follows is an account of each of these great miners' achievements and the problems they faced, and an assessment by some of today's mining leaders of the challenges that lie ahead.

Jan 7, 1976

By Reno H. Sales

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

By Sales, Reno

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By Frederic P. Dewey

The improvement in leaching introduced by the Russell process has stimulated the development of processes for refining lixiviation-sulphides. In the early days several processes for dealing with the sulphides were proposed, and some of them were tried more or less ; but the business finally settled down to sending the sulphides to the smelters, although this was known to be both troublesome and expensive. In 1891 Mr. C. A. Stetefeldt* introduced at the Marsac mill, Park City, Utah, an unpatented process, built up out of the general fund of information available. It consisted in matting the sulphides, grinding, roasting, grinding again, and dissolving the copper out in diluted sulphuric acid, then melting the silver and crystallizing the bluestone. It did not yield fine bullion, hence the bullion had to be refined as well as parted; besides, there was some loss. This process was thoroughly tried at the Marsac refinery and then a year's run was made, the net result of which was that it did not prove sufficiently better than the sending of the sulphides to the smelters to warrant its substitution for that practice. In 1893 the Dewey-Walter Refining Company undertook the refining of the Daly sulphides in the Marsac refinery by the sulphuric acid process, upon which two United States patents ? have been issued to the writer. Naturally, difficulties were encountered in starting a new process, and most of 1893 was taken up in getting it into smooth working order; but in 1894 a run was started, in which all the regular sulphides produced by the

Jan 1, 1897

By Henry Lloyd Smyth, J. Ralph Finlay

The most important area of the so-called Keewatin rocks of northern Minnesota is that which runs westerly from Lake Saganaga, near the national boundary, and finally disappears beneath the drift (or has not been farther traced), in the neighborhood of Vermilion Lake. With this belt we have a general acquaintance, extending back some four years. During the past year we have had the opportunity of studying in considerable detail a small part of it, embracing an area of about 12 square miles on the south and east shores of Vermilion Lake. In this paper we desire to record our observations and conclusions, which seem to us important. II.—Literature. Outside the Minnesota Geological Survey, the list of the investigators who have studied the geology of the Vermilion Lake area is not long. Whittlesey, in 1876,* mentioned the occurrence, in the area about Vermilion Lake, of rocks resembling the Canadian Laurentian. Chester,? in 1884, described the iron-ore at Vermilion Lake as occurring in connection with jasper and quartzite, intimately bedded with the country-rock, chiefly sericite schist, and standing in a nearly vertical attitude. The Vermilion iron-bearing rocks, and those of the Mesabi range, he says, are of the same age.

Jan 1, 1896

By Newell Alford

AT its meeting in the fall of 1937, the Executive Committee of the Coal Division considered the growing scarcity of young engineers entering coal mining with serious intentions. This scarcity was the cause of con-siderable alarm and a committee consisting of C. T. Hayden, E. A. Holbrook, C. E. Lawall and L. E. Young, with the writer as chairman, was appointed to gather factual data on the current trend. A questionnaire1 was designed and mailed to the heads of the 60 mineral technology schools listed by Prof. W. B. Plank in his article in September 1937.2 Replies were received from 46 institutions, not all from heads of coal-mining courses but all from men that at one time or another have had experience with some kind of coal-mining curricula and know current student impressions. Our committee is indebted to all of these gentlemen for their cooperation. Our committee hoped by this means to quickly reach the root of the trouble and make a set of comprehensive recommendations to the Coal Division for relieving the industry immediately from the growing dearth of youth who yearn for coal-mining careers, but the condition is more serious than at first diagnosed. We must now refer the question back to the Coal Division, with the recommendation that the Division get the industry's permission for still another major operation on its frame of mind. In addition to 10-year statistics on the first pay received by graduates in coal mining and other technical work, we requested enrollment data for 20 years from all schools with either mining engineering or mineral technology curricula. Nine leading questions were also plied, as shown in the Appendix. Every one of the answers was significant and inter-esting. Fortunately, we encountered positive frankness that was extremely helpful.

Jan 1, 1938

By J. D. Price, W. M. Bertholf

Making maximum possible use of available equipment and material, CF&I placed a high-efficiency, high-capacity washery unit in the existing buildings to gain simplified operation, reduced manpower requirements, raised efficiency, and boosted production. THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers. In the late 1940's it became evident that something would have to be done to keep the washery abreast of progress at Pueblo and other washeries. Coal requirements were nearly two and one-half times the original requirements of the 120 small ovens, as additional ovens had been built in 1930, 1938, and 1945, whereas no additional coal washing capacity had been added since the 1936 modifications. Much of the equipment, moreover, had seen better days. One answer to the problem was to build a new and completely up-to-the-minute plant, with sep- arate sections for coarse, medium fine, fine, and very fine coal. On the other hand, it might be financially more profitable to place a high-efficiency, high-capacity unit in the existing buildings. The washing problem at Pueblo is not unique, but it is approached differently. There are no established specifications for coke ash and sulphur. The plant is operated on the principle that if it is more economical to wash it out than to slag it out, wash it out; otherwise, send it on to the blast furnaces. With coals at the Pueblo plant costing what they do, the benefits of washing at a low gravity are questionable. Hence the primary problem is to eliminate the high-ash components and retain all the low and medium-ash components. Sulphur is no problem at all, averaging 0.6 pct in the coke. Since a good proportion of the free impurity in the coals is as large as the coal or bone or larger, it appeared that it would be safe to go to jig washing and discontinue crushing the coal before washing, as had been the practice with the tables. This would boost the throughput. It might also decrease manpower requirements and washing costs considerably. It was assumed at the start and has been demonstrated in the first year of operation that a jig will do as well on the fines as the tables had been doing. It would not be necessary to discount any gains due to increased efficiency in washing the coarse material because of incapacity to wash the fines. By washing at —2+0 mesh it would be possible to dewater, by screening, a considerable tonnage satisfactorily, for example, at —2 + % or —2 + l/4, and then crush it in a hammer mill. The —?+20 could be dewatered in centrifugal driers and the remain-

Jan 1, 1955

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of' these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940