Search Documents

By Herbert R. Mosley, Paul M. Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer- consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommercial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee's phosphate-mining industry dates from the discovery of blue rock in-lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By Charles H. Morgan

THE process of wire drawing depends upon the property which certain metals possess, termed ductility, 'which is defined in Brande's Dictionary of Science as a property in consequence of which metals may be drawn out at length without interrupting the continuity of their constituent parts. As defined by M. Tresca, it is the property of flowing when subjected to pressure, and is termed by him the "flow of solids," in his paper, read before the Academy of Sciences in Paris, November, 1865 * In the simple language of the wire shop, it is that quality in certain metals that permit, them to be drawn (or stretched) out through a tapering, hole in a metal block or die, the die being more dense and harder than the metal to be reduced. It is a fact well known to those skilled in the art, that to succeed in drawing iron or steel wire, it is of the utmost importance to have thorough lubrication, as a lack of it would caws abrasion of the wire, or of the walls of the tapering hole in the die or plate, and quickly put an end to the operation. In drawing coarse or large sizes of wire, say 2/10 inch diameter, the pressure upon the sides of the tapering hole, where the wire comes in contact with the die, is so great that an ordinary lubricant is squeezed out when the usual reductions in size are made, and abrasion takes place. In order to meet this difficulty, and secure proper lubrication, it has been' a common practice for years to apply a paste made of rye or wheaten flour, or lime, to the surface of the wire to be drawn, and when the paste is dry, to smear the wire with tallow or grease; the wire is then ready to be drawn, the dried paste serving to prevent the lubricant from being pressed out in the. process. Some years since, when Bessemer metal came largely into use as material for wire, "the writer found that its drawing required so much more power than iron wire, that he was led to institute a series of trials to ascertain the difference in power required. It was found that Bessemer wire required from 100 to 200 per cent. more power to make the same reduction in sizes than soft iron wire, the difference depending upon the amount of carbon and other chemical constitu- * Interesting experiments in the flow of metals have been made, by Messrs. Hoopes Townsend, of Philadelphia, in cold-punching iron, published and illustrated in the Journal of the Franklin Institute, of March, 1878, by Mr. David Townsend.

Jan 1, 1881

By J. A. Bownocker

THE production of oil in Ohio, in 1924, was characterized by no marked or surprising change. Low prices and the absence of promising territory made the year quiet. As is well. known, Ohio has reached a state of "settled production," and the most that can be expected for the ensuing few years is to maintain the output at approximately the present figure 1921 7,335,000 1922 6,781,000 1923 7,085,000 Geographically, the Ohio fields may be divided into three areas, each of which gets its main supply of oil from a different stratigraphic horizon.

Jan 3, 1925

By Duk-Won Park, Syd S. Peng

INTRODUCTION More than five years have elapsed since the first shortwall panel was installed in a US mine in 1972. By the latest count, 11 mines have tried the shortwall method on 34 panels. Potentially, the shortwall method (see Figure 1) offers the combined advantages of longwall and continuous mlning. But just like any other mining method, shortwall is not a panacea. It is only applicable under a set of stringent conditions. Coal operators at eight of the eleven mines are satisfied with shortwall mining, though there are only five mines presently producing coal from shortwall panels.

Jan 1, 1981

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4'5 dense patches or clusters of prismatic dislocation loops, planar arrays,4'10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10' life level the

Jan 1, 1969

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, LOUIS K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

THE twenty-first birthday of the Rocky Mountain Club will be celebrated on April 11 by the Last Round-up; for, as announced at the annual meet-ing of the American Institute of Mining Engineers in February, the Club and the Institute have voted to con-solidate and formal approval by the court alone re-mains to be secured. The Rocky Mountain Club was organized some years since "to create and maintain good fellowship between the Rocky Mountain members and to further the in-terests of the Rocky Mountain States." From the first, mining men dominated it, as was natural in view of the prominence of mining in the Rocky Mountain region. A series of brilliant annual dinners were held and a site purchased for a clubhouse. A fund was raised to provide a home for the Club. Just as success was as-sured the war came and the members of the Club con-sidered it would be unpatriotic to spend money for such purpose at that time. In a spirit of patriotism the Club funds were devoted to war purposes, especially the Commission for Relief in Belgium and the caring for soldiers going to and returning from the front. So much of the money was used that at the end of the war the project for a clubhouse was out of the question with-out raising a new fund, and since 1923, the Club has been inactive. There is now in its treasury a substan-tial sum. The assets are for the most part the result of contributions made by W. B. Thompson, John Hays Hammond, and Edward H. Clark, all members of the Institute and all of whom wished to see these funds applied in a manner to leave some lasting memorial of the spirit which animated the founders and at the same time perform some useful function in the development of the region in which the Club's interest centered. It was thought that this could best be done through affilia-tion of the Club with the Institute and both organiza-tions have voted for the merger. The Club members not already in the Institute are to have the privilege of a special Rocky Mountain life membership, and the property of the Club is to be used to endow a Rocky Mountain Club fund to be used for purposes in accord with those of both the Institute and the Club and with especial reference to benefiting the Rocky Mountain region.

Jan 4, 1928

By A. B. Bowman

The 1963 Jackling Award lecturer describes the founding of Banner Mining Co. and its trials and tribulations before becoming an established firm. Such aspects as geological description of Banner mining areas, history of exploration and production, areas of present interest to the company and research work conducted by the company are included. Several years ago a wealthy Chinese business friend of mine purchased an interest in a proposed oil well to be drilled a great distance from his home. A few months later it came in as a producer and proved to be a huge success and materially added to his resources. I asked him why a man of his wealth should be so lucky in a venture outside his sphere of knowledge when most people of modest means never seemed to get ahead. His answer was, "Fat Hoy takes a chance." Even though this was his answer, I knew from my association with him that there were other tempering considerations which Mr. Hoy applied before making up his mind to enter any transaction. First, he was a cautious individual. He was also a great believer in details and insisted on knowing everything possible about a situation, and finally, he was what we call a very solid individual with good basic instincts and judgment. This philosophy of Mr. Hoy may be applied to most any business but especially to those engaged in a search for natural resources such as mining where great risks are involved. This article concerns events in the history and growth of Banner Mining Co., with which I have been associated for 27 years in capacities from mine surveyor to vice president. Mr. Hoy's philosophy has played a significant role in the exploration projects of this company over the years, but what is more important, the officers, directors, and controlling interests in Banner have been aggressive in their search for ore reserves. THE BIRTH OF BANNER Banner Mining Company was incorporated in September 1935 by a group of Oklahoma and Texas oil men for the purpose of exploring and developing the Bonney-Manilla mines at Lordsburg, N.M. These properties had a history of intermittent production since the first ore discoveries as far back as 1870. Most of the production from the district has come from four mines, namely, the Eighty-Five, the Atwood, the Bonney-Manilla, and the Misers Chest. The last two are now owned by Banner Mining. The Eighty-Five mine operated between 1885 and 1931, and production totalled 1,494,287 tons averaging 0.11 oz of gold per ton, 1.23 oz of silver per ton, and 2.80% copper. The vein extended for a distance of about 3000 ft northeast and was mined to a depth of 1650 ft. The Atwood mine, adjoining the Eighty-Five mine, to date has been of lesser importance as a producer, but it has been operating for several years producing high silica flux ores for a smelter. Production totalled 352,828 tons up to January 1, 1962 From the Bonney-Manilla and Misers Chest mines, owned by Banner, production through 1961 totalled 2,006,343 tons with an average grade as mined of 0.0192 oz of gold per ton, 0.760 oz of silver per ton and 2.63% copper. Banner built a 150-tpd flotation mill in 1936 after almost a year of development on the 600 level of the Bonney mine. After less than one year's operation, it became apparent that the 150-tpd rate was not sufficient to make a reasonable profit due to the marginal grade ores. The low tenor of the ore, mainly chalco-pyrite in a highly siliceous gangue, made mandatory the close control of costs in order to make ends meet. A 300-tpd unit was added to the mill in 1937, and it is still the operating unit today. The clean sulfides presented no problems in milling. A metallurgist doing research on it at the time stated that the copper minerals seemed to have a built-in desire to float. Mill recovery of copper throughout the 27 years of operation has averaged 96.23%. A PERIOD OF FORCED GROWTH World War II brought many hardships to Banner. Labor and supply shortages caused drastic curtailment in development work. Rapidly rising costs far outdistanced any relief from pegged prices which we received from Government agencies. Finally, a branch of the Government asked us to stop all devel-

Jan 1, 1963

By J. J. Sense

This paper deals with the Asarco method for the determination of equipment availability. It is apparent that no single availability equation will provide all of the information necessary for the complete record of equipment availability. In the Asarco system, three separate availability records are carried on major equipment. The first is mechanical availability, the second is operational availability, and the third is a historical record of equipment use. The derivation of the three items and the definitions of the time elements used in the various availability equations are presented and discussed. The Mission unit of American Smelting and Refining Co. is located in Pima County, Ariz., approximately twenty miles southwest of Tucson. The unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to company smelters at Hayden, Ariz., or El Paso, Tex. Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tpd concentrator was started in the spring of 1960. The first ore was treated in midsummer of 1961 and full ore production was reached in August 1961. At that time over 46 million tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tpd. Total production to date (ore and waste) is over 120 million tons. Major equipment currently in operation at the Mission pit is as follows: 3 P & H 1800 Electric Shovels - 9 cu yd dippers 1 P & H 1900 Electric Shovel - 9 cu yd dipper 2 B.E. 190-B Electric Shovels - 9 cu yd dippers 35 Euclid LLD Trucks - 60-ton capacity 6 KW-Dart 55-T Trucks - 55-ton capacity 1 KW-Dart D-2550 Truck - 65-ton capacity 1 LeTourneau Westinghouse 65 Haulpak - 65-ton capacity 3 Euclid S-18 Scrapers - 274011 capacity 4 Caterpillar D-8 Dozers 4 LeTourneau Westinghouse Tournadozers 1 Michigan 280 Dozer 2 Caterpillar Model 12 Motor Graders

Jan 1, 1964

By Oliver Halston

THIS paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Proutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work. Lead Metallturgy Popularly Supposed to be Without Problems In bead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that bead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the 3 years of work of the Salt Lake Station, the following classification of problems in the metallurgy of bend has been made: Those involving Oxidized Ores. 1. Ores containing only bead. s. Ores containing bead and silver or gold. 3. Ores containing bead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some bead. 2. Ores of complex zinc-bead-iron sulphides. 3. Complex sulphides containing in addition precious metals.

Jan 8, 1917

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first' outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927

By E. S. Greiner

THE hot working of chromium was first reported by Hunter and Jones; who used small pellets of the material obtained by the reduction of chromium chloride with sodium. Later, the working of chromium at 600° to 1100°C was reported by Marden and Rich,2 and at 1250°C by Kroll3 The hot rolled material3 had a Brinell hardness of about 150 (62.5 kg, 2.5 mm ball, 1 min) and was brittle at room temperature. Except for that associated with hardness indentations, no plastic flow in chromium at room temperature has been reported to the author's knowledge. Studies described here have shown slip markings in chromium after deformation at room temperature.

Jan 1, 1951

By W. J. Babyak

The habit planes for hydride precipitation in large grains of alpha zirconium and Zircaloy-4 were determined in specimens containing 161 and 136 ppm hydrogen, respectively. In zirconium, the hydride platelets precipitated on various pyramidal planes inclined to the basal plane at angles ranging from 10 to 50 deg and 75 to 90 deg. Hydrides were most frequent at inclinations of about 20 deg and 90 deg. In Zircaloy-4, hydride plates were inclined to the basal plane at angles vanging from 5 to 25 deg with the predominant inclinatioiz equal to 12 deg; no platelets were found near the prism plane position. In both zircoinium and Zir-caloy-4, hydrides were principally, but not exclusively, parallel to (1011) type planes. When the Zircaloy-4 gmins were subjected to tension stresses of 12,100 psi and 19,400 psi during hydride precipitation, the hydride habit was unchanged except that precipitation favored those habit planes which were inore nearly perpendicular to the stress direction. The stress-orientatioiz effect increased with the magnitude of the stress. THE hydride habit plane in a zirconium has been determined by several investigators. Langeron and Lehr1 in 1956 found platelets parallel to (1010) slip planes. In 1962, Westlake and Fisher2 confirmed these findings and showed that hydride precipitation on twin planes, as reported by Kunz and Bibb,3 was probably due to incomplete removal of worked metal from specimen surfaces. Secondary habit planes, ( 1011) and (1015), were also found by Westlake and Fisher under particular charging conditions where a hydride layer may have existed at the hydrogenation temperature. Most recently, walters4 and westlake5 again observed the (1010) habit exclusively in zirconium. Louthan and hgermans have reported that hydrides precipitate on various ( 101l ) and (112l) planes positioned 31.5 to 90 deg to the basal plane in Zircaloy-2. The present investigation was concerned with the hydride habit in Zircaloy-4 in relation to that in zirconium and the possible change in habit when precipitation occurs under stress. The latter consideration was prompted by the stress-orientation phenomenon originally reported by Marshall and Louthan.7, 8 I) EXPERIMENTAL Materials and Specimens. Chemical analyses of all materials are given in Table I. The zirconium specimen was a 1 by 4 in. section cut from wrought crystal bar that was hot-rolled at 790°C to 0.300 in. and cold-rolled to a final thickness of 0.095 in. All surfaces were mechanically polished and then chemically polished with a solution of H2O, HNO3, and HF (10:10:l by volume) prior to annealing. Grains as long as 0.25 in. were grown by thermally cycling the specimen three times (in 10-5 mm Hg vacuum) between 825" and 1000°C at approximately 125°C per hr. The specimen was isothermally annealed at 825°C for 24, 40, and 120 hr after each cy-

Jan 1, 1968

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting), but a few mimeographed copies of this provisional report are at the A.I.M.E. headquarters and will be mailed on request. . Dr. W. P. HAYNES presented some notes prepared by Dr. F. H. LAHEE, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Committee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training.. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. SHERWIN F. KELLY pointed out that much time in university training, which ought to be devoted to technical subjects, was taken up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. THOM protested against the crowding of high-school material into already overcrowded college curricula. C. E. DOBBIN, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat, toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1941

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By W. F. Hergert, L. H. Banning

Experimental production of Al-Si alloys, containing from 33 to 55 pct Al, by direct reduction of aluminum silicates in a three-phase arc furnace is described. Advantages of a smelting technique utilizing hogged wood waste as part of the reductant and for temperature control are discussed. WORK on the problem of producing aluminum by smelting has been in progress since the middle of the eighteenth century. Early work met with little success and in 1782 Lavoisier, an eminent French chemist, expressed the belief that alumina could not be reduced by carbon. It was almost a century later when the Cowles brothers developed a process for the production of aluminum alloys by reducing alumina coincident with the reduction of other metal oxides. In practice, the other metal oxide was usually copper. In 1907 it was first shown that alumina alone could be reduced by carbon at a temperature of 2200°C. The metal produced was volatilized and lost or recombined with the oxides of carbon formed in the reaction.' For a number of years after the Cowles brothers abandoned production of Cu-A1 alloys because their product was not commercially competitive with the aluminum produced by the Hall process, there was little interest in thermal reduction processes. After World War I interest in such processes was renewed and a number of patents were issued on processes for the production of A1-Si alloys.' , "he function of the silicon in these processes was the same as the function of the copper in the Cowles brothers process, namely, to prevent the reduced aluminum from recombining with the oxides of carbon and to promote absorption of the aluminum vapors set free at the high temperature required for the reduction reaction. The advantage of using silicon in place of copper for this function is that silicon has a higher boiling point (2600"C) than copper (2310"C) and its oxides, combined with aluminum oxides, occur in nature in almost unlimited quantities. No A1-Si alloys have been produced commercially in the United States, as far as is known. However, considerable experimental smelting of aluminum silicate materials has been done by the TVA at Wilson Dam, Ala.' The most extensive development and commercialization of the electrothermal production of A1-Si alloys took place in Germany before and during World War II.V he furnaces used in the

Jan 1, 1956