Search Documents

By W. J. Keep

Those who have observed the influence of various elements upon cast-iron will be interested in the methods used by us to form the several series of test-bars, which form the basis of the conclusions presented in this paper. We found that we could not, by adding ordinary white stickphosphorus to molten iron, produce bars which would exhibit to the eye the peculiar influence of phosphorus. By melting wrought-iron drillings with red phosphorus, Mr. H. S. Fleming produced in his laboratory 10 pounds of phosphide of iron, containing 10.22 per cent. of phosphorus. With this we made two series of test-bars, the first with our white-base iron, and the second with our FLM gray-base iron. Before the time of making these bars we had been unable to procure regularly made pig-iron which contained enough phosphorus to permit of the production of

Jan 1, 1890

By Larry J. Tucker

INTRODUCTION The orebody at Pea Ridge strikes NE-SW and dips at about 800 to the SE. The ore and surrounding rocks are Pre-Cambrian in age. These rocks are usually very competent. Locally strong jointing has caused problems and toward the hangingwall dikes have caused particular problems during or after the open stoping phase of production. About 396 m of sediments lie over the ore. The shape and mineral content of the orebody has been fairly consistent so far with production areas lying from the 1375 to the 2475 levels. The deeper limits of the ore- body haven't been found yet. The ore is high grade magnetite with a strike length of over 600 m and a maximum width of over 180 m on some levels at the center of the orebody. Production at Pea Ridge for the first three years of operation came from two types of open stopes. The original stopes were recovered with horizontal production rings being drilled and blasted from vertical raises. Later a more typical sublevel stoping method using vertical production rings from one or more drilling sub- levels was used. There were a number of reasons for the selection of open stoping as the initial production method at Pea Ridge. First, it was judged that the ore was not of a block cave quality. After fifteen years of production, this assumption can be verified. There was some concern during the planning days for the potential for high flow rates of water into the mine from aquifers in the sediments lying over the orebody. Dewatering wells from surface and underground were put in as a precaution and nothing came of this potential problem. Open stoping and its resulting pillar structure put off this problem by supporting the sediments a few years longer. For a moderate investment in level development some production from open stoping was quickly realized. The first open stopes were brought in on what was then the bottom mine production level (2275), near the shaft pillar and situated on the footwall. This production practice of stoping on the heels of development from shaft pillar westward and from footwall to hangingwall continued through the open stope phases of production at Pea Ridge for many years. From the standpoint of mine efficiency and pillar stability, this would not seem to be a recommended mining practice. 74 570 w electric slushers, using 1.37 m dippers, pulled the open stope ore out into 18 ton bottom dump cars. Ordinarily five of these cars made up a train, which was pulled to the dump area by a trolley powered electric locomotive. Open stoping had the disadvantage that 100% of the recoverable portions of the orebody had to be developed in order to recover 33% of the ore. 67% of the ore was left behind in a large pillar system. For many years we had no planned method for recovery of these pillars. Mining methods are of course, limited by the existing technology. Advancing technology, coupled with the limited production capabilities of open stoping, low efficiencies and high relative cost early in the history of the operation recommended that other mining methods be looked at. In Sweden, considerable practical experience, coupled with a large amount of theoretical work had become available on sublevel caving. To Pea Ridge it offered the apparent benefits of: 1) The flexibility of diesel powered trackless haulage. 2) The efficiency of two machines to one operator on longhole drilling. 3) A multilevel production picture with a large number of drawpoints for ore recovery. 4) 100% recovery of the mineable portion of the orebody in one production pass, with no pillar recovery problems left behind. This paper outlines the experiments and experiences which Pea Ridge has gone through with sublevel caving from 1967 to this date.

Jan 1, 1981

By Rudolph G. Wuerker

With stepped-up work in rock mechanics, more and more data on strength and elastic properties of rocks has become available. Results of measurements of tensile strength, in addition to determinations of compressive strength, allow us to deter- mine, even if only in an approximate way, the third property influencing failure of a brittle material: shear strength. It is fairly generally agreed upon in rock mechanics, in drilling and blasting research, that Mohr's theory provides an acceptable method for explaining the failure of a brittle material. Mohr states that a material may fail either 1) through plastic slip when shearing stress Y in the planes of slips has reached a limiting value (which in general depends on the normal stress, X, acting normal to the surface), or 2) when the largest normal tensile stress has reached a limiting value. The mode of failure depends upon which of the two stresses is the smaller.

Jan 10, 1959

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

By J. B. Scott, J. S. Nelson, G. H. Kruse, W. S. Johnson, K. L. Zerneke

The economics of pressure tunnel design emphasize the utmost utilization of the least expensive pressure-resisting material available, namely, the rock surrounding the tunnel. A major difficulty in the design is the problem of transferring internal hydraulic pressure to the rock through a tunnel lining or membrane provided to maintain watertight conditions. The lining is necessary not only to prevent water loss, but to prevent the diffusion of water at high pressure through joints and fractures beyond the confines of the tunnel, an occurrence which could ultimately affect the stability of the rock mass through which the tunnel passes. Because of its toughness and ability to bridge localized areas of weakness, steel is used for a lining material whenever high internal pressures are involved. The steel lining is coupled to the surrounding rock mass through an annular ring of concrete backfill. It is paradoxical that the steel lining, needed primarily to assure water tightness, must of necessity be incorporated into the structure as a major pressure-resisting component, not to augment the bearing capacity of the concrete and rock, but to limit the strain for the safety and preservation of the steel lining itself. With the deformation modulus of the steel so much greater than that of the rock, the liner approaches its yield strength before the load capacity of the rock can be fully mobilized. An economical determination of plate thickness for steel liners is therefore dependent upon measurement of the properties of the surround-

Jan 1, 1970

By W. H. Emmons

Although gold is one of the rarer metals, it is widely distributed; it is found on all of the continents and in each of the grand metallogenic provinces of the earth. It is prominent particularly in the shield areas of the earth; these areas have produced a large part of the world's lode gold and in most of them gold lodes are more important than the lodes of other metals. The Scandinavian shield is the only one that has not produced much gold. Nearly all of the world's gold has been derived from lodes and from sands and gravels where gold placers formed by the destruction of lodes. The gold derived from magmatic segregations, from pegmatites and from contact metamorphic deposits is quite subordinate to that derived from auriferous lodes. The lodes include all veins and related deposits that are formed by hot waters that move along fissures or other openings and that deposit vein 'matter :in the fissures and by replacement of the country rocks along the fissures. All of the shield areas of the earth are characterized by large areas of granitic rocks including granitic gneisses, granodiorites and other acid intrusives which here are included in the general term "granite." The granites are intruded into schists, ancient lavas and other rocks which here are designated as the "invaded" rocks. The granites are parts of what once were great batholiths: that is, they are the remaining portions of great deep-seated bodies that slope outward, have very irregular roofs and so far as known have no floors but extend downward to great though unknown depths. Some of them are scores or hundreds of miles across and contain islands or "roof pendants" of the invaded rocks at places where the roofs of the batholiths were low—that is, where erosion has not yet completely unroofed the batholiths. It is in these islands of older rocks and in the narrow marginal belts and cupolas of the batholiths that practically all of the gold lode deposits of the shields are found. Valuable lodes are lacking generally in the granites themselves except in grahite within a mile or less from .the contacts with rocks of the islands (Fig. 1). It is probable that the great areas of granites and gneisses that surround the islands are not all of the same age, and that at places unmapped granite intrudes gneiss or older

Jan 1, 1932

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

In the history of American mining, so far as I know, there is no cleaner, brighter, or more completely successful mining adventure than that of the United Verde Extension.* It deserves to be placed on record here. The mine is at Jerome, 25 miles northeast of Prescott, in Yavapai county, Arizona. For 30 years before the U.V.X., as it is known to mining men, achieved celebrity, the Jerome district was identified with a copper mine, the United Verde, one of the great mines of the world. The success of this mine, of course, stimulated the search for similar orebodies, or for an extension of those already known, in adjacent ground; but, despite vigorous prospecting, the United Verde remained for many years alone in its glory. The reason for this solitariness was geologic: a fault with a big throw frustrated the effort to trace the ore-zone, thereby causing exploratory work to be both uncertain and costly. Despite these failures to develop other mines in the vicinity, the belief persisted that all the ore was not localized in the United Verde mine, but before we consider the reasons for such a belief we must look at the geologic conditions. The basal rock of the Jerome district is a schist, which has been correlated with the Yavapai formation of the Bradshaw quadrangle. This schist is geologically ancient, for it is of pre-Cambrian age. It is composed of volcanic tuffs, together with sediments, both argillaceous and siliceous, all of which

Jan 1, 1932

By N. A. Richard, A. E. Austin, R. E. Maringer

AS part of a detailed study of the structure of metallic meteorites, the concentration and distribution of iron and nickel in the various phases of meteor -itic iron have been measured using an electron-probe microanalyzer. The specimen used was cut from a position about 3 in. below the surface of the Grant meteorite, a one-half-ton iron specimen (containing 9.35 pct Ni) found in New Mexico some years ago. A photomicrograph showing the general Widmanstztten structure, somewhat typical of iron meteorites, is shown in Fig. 1. The line across which the analyses were made is indicated by arrows. This area was chosen so as to evaluate the iron-nickel concentration in the three principal phases visible in Fig. 1. These phases, in the language of meteoritics, are kamacite, taenite, and plessite. Kamacite is the a-

Jan 1, 1960

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By Burnham E. Field

The chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is one of the more important forms of corrosion and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling this acid under plant conditions.' The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others12 but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum. 3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By Morris Muskat

A general theory has been developed for the effect of permeability stratification on the efficiency of the gas-injection phase of cycling operations. It has been applied to three special types of permeability variation; namely, exponential, probability, and linear. In the case of the exponential permeability distribution the effect of areal pattern sweep efficiency was also taken into account. The exponential permeability distribution can be characterized by the ratio of the maximum to minimum permeability, which has been termed the stratification constant. Curves were calculated for the variation in total wet gas recovery and total gas throughflow, to give that recovery to various abandonment limits of the wet gas content in the produced gas, as a function of the stratification constant. The cumulative wet gas recovery decreases monotonically as the stratification constant increases and is generally higher at the lower values of the wet gas content abandonment limits. The total gas throughflow first rises to a maximum as the stratification increases, and then ultimately declines. The effect of the areal sweep pattern efficiency is relatively minor as compared to that of the stratification constant, except in the region of low values of the latter where the formation is substantially uniform. The probability distribution can be characterized by a "variation" parameter varying from o to I as the formation changes from strict uniformity to extreme variability. The curves of total wet gas recovery and total gas throughflow to different abandonment limits of wet gas content versus the variation parameter have the same general characteristics as for the exponential permeability distribution. In the linear permeability distribution the ratio of maximum to minimum permeability also serves as a stratification constant index defining the distribution. The curves of total wet gas recovery and gas throughflow to fixed abandonment limits versus the stratification constant are similar to those for the exponential permeability distribution. However, for the higher values of the stratification constant the recoveries and throughflows do not asymptotically fall to o as in the latter, but approach constant values determined by the abandonment limit of wet gas content in the produced gas. Introduction It is becoming generally recognized that one of the most important factors determining the economic feasibility of cycling operations is the areal continuity and permeability distribution of the producing formation. While the effects of areal variations in permeability, porosity, thickness, and well pattern on the sweep efficiency can be evaluated by electrical model studies,' those due to permeability stratification require separate treatment. Several studies have been reported2,3 on the' influence of permeability variations on the wet gas recovery by cycling. In these, however, discontinuous permeability variations either have been assumed explicitly, or the analysis has been carried through as if they were discontinuous. While, in fact, the actual permeability profiles will undoubtedly be discontinuous, recent develop-

Jan 1, 1949

Discussion of the paper of W. G. MATTESON, presented at the New York meeting, February, 1918, and printed in Bulletin No. 134, February, 1915, pp. 429 to 468. WILLIAM KENNEDY, Fort Worth, Tex. (written discussion*). -In his discussion of this paper, Mr. Sherburne Rogers offers voluminous figures to show that the salt forming the. cores of the various domes could not have been derived from sea water, and gives as an illustration the immense quantity of water required to form the salt found in the Humble dome. He refers to the theory advanced by Van der Gracht apparently in support of this contention, and claims to have disposed of the views held by some that the domes were, in a great measure, formed by lateral secretion. Van der Gracht says the immense salt plugs found throughout North Germany and other countries in that region were apparently formed by orogenic movements acting upon what he calls the Mother Bed of Salt, which he gives a thickness of about 1000 ft., and an extent of several thousand square miles. The age of this "mother bed" is given as Permian. Harris, in addition to his growing-crystal theory, also says probably a great portion of the salt found in the Coastal dories may have been derived from the salt water of Permian time. Both of these theories require an abundance of water, and consequently oppose Mr. Rogers' idea that the immensity of water required disproves the formation of the salt from that source. I do not suppose, however, that either Van der Gracht or Harris absolutely limits his view to the Permian as being the only source from which the salt could have come, but would probably agree to consider any other age as being the beginning. Although the Permian is very strongly represented throughout North Texas, we have none anywhere throughout the region from which the salt may be considered as having been derived. Many deep wells have been drilled along the eastern outcropping of the Carboniferous and each has passed directly from Cretaceous to Carboniferous formations. Thus we may eliminate the Permian as a source of salt in this region. But, although the Permian may be absent, we have with us the Carboniferous with probably a thickness of 3000 to 4000 ft., and something like 3000 ft. of Cretaceous, to say nothing of approximately 8000 ft. of Tertiary and later beds, all of which, if we may judge by the quantity and density of the waters obtained from the numerous wells drilled, carry immense quantities

Jan 7, 1918

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Richard Pearce

I am deeply sensible of the honor you have conferred on me in electing me your president for this year. It is difficult to understand why I have merited such distinction at your hands, except that I may possibly have helped, in some small way, in the develop ment of metallurgical practice in the West. I fear, however, that I shall fall far shirt of the expectations you may have in regard to my fitness for such a position. The responsibility of preparing an address for this occasion has caused me considerable thought and anxiety. Unlike my predecessors in office, many of whom have dealt in their presidential addresses with subjects covering a wide field, which they could survey with the confidence born of their own extensive knowledge, I have been confined by my experience, during the last twenty-five years, almost wholly to that portion of metallurgical science which bears especially on the treatment of gold and silver. Yet perhaps some sort of general review of the progress of this branch of metallurgy in the West, besides being the contribution I feel myself best qualified to offer, may prove acceptable to many of the members of the Institute. Some few of the gentlemen present will remember the crude condition of metallurgical practice as it was conducted in Colorado only twenty-five years ago. My own personal experience covers a period of eighteen years; and during this comparatively short time I have seen the most astonishing changes in the conduct of metallurgical works. In all probability the marked progress which this country has exhibited could hardly be reached anywhere else, and this result has been achieved mainly by the activity and enterprise so characteristic of the men of the West. The first little successful attempt at smelting made at Black Hawk, in 1867, by Ex-Senator N. P. Hill, representing the Boston and Colorado Smelting Company, proved a great boon to the miners,

Jan 1, 1890

The Institute is at present in sound condition professionally and financially. During the past year 546 new members were elected, the total membership now numbering 5,221. The Treasurer's Report shows that the expenses of the Institute are met by its income. Your Directors have thought it wise to issue a referendum to the members asking for a vote upon the suggestion that the annual dues be raised from $10 to $12. This moderate increase is proposed not because the Institute needs it at present but to insure a continuation and increase in its activities and usefulness, and to provide a reserve fund for future emergencies. In well-conducted organizations, such as clubs, it is a wise and safe course to so adjust the clues of members that the total receipts from this source will about equal the annual expenditures, the initiation fees being used for reserve purposes. Our dues alone do not at present meet the expenses. This, I think, is the whole situation, so far as this question is concerned. Expenses might be reduced in some measure, but they cannot be materially reduced without affecting the integrity and usefulness of your Institute. Nothing of consequence in our internal affairs has occurred during the past year except, perhaps, the establishment of the Arizona Section and the prospect now assured of a Nevada Section. During recent months there has been a marked change in the relations of the Institute to its fellow societies and to the Government of the United States. That change is one of cooperation. The Secretary of the Navy has appointed two of your members to the Naval Consulting Board to cooperate with members of 10 other scientific organizations. This Board is now organized, and through its work your Institute is brought in close touch with the activities of the other societies and with the United States Navy. The President of the United States has requested us to recommend to the Government one of our representatives in each State in the Union to act in collaboration with a member in each State from the. American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers and the American Chemical Society, thus organizing a directorate of engineers for each State, that will conduct, through the members of each of the five societies referred to, living in each State, a campaign of industrial preparedness. No more important step than this, it seems to me,

Jan 3, 1916