Search Documents

By AIME AIME

A discussion of the Papers by Prof. H. Hubert, Liege, Belgium ; Mr. Tom Westgarth, Middlesbrough, England ; and Mr. K. Reinhardt, Dortmund, Germany, presented at the London Meeting, July, 1906, and printed in Bi-Monthly Bulletin, No. 12, November, 1906; pp. 910 to 930, 971 to 987, 1037 to 1163. MR. ADOLPH GREINER, Seraing, Belgium :-I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have cor-rected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix II. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p; in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. MR. Tom WESTGARTH, Middlesbrough, England:-My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by the engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have be-

Jan 1, 1907

By Francis Collins, E. R. Brownscombe

A study has been made of the material balance-fluid flow method of estimating reserves and degree of water drive from pressure and production history data. By considering the effect of random pressure errors it is shown that in a particular example a standard deviation of three and one-half pounds in each of ten pressure survey? permits the determination of the reserves with a standard deviation of 8 per cent and the water drive with a standard deviation of 15 per cent, assuming that certain basic geologic data are correct. It is believed that this method of estimating reserves and water drive is useful and reliable in a number of cases. The method is particularly valuable when reservoir pressure data are accurate within a very few pounds, but may also be applied with less accurate pressure data if a relatively large reservoir pressure decline occurs early in the life of the field, as for example in an under-saturated oil field. INTRODUCTION A knowledge of the magnitude of reserves and degree of water drive present in any newly discovered petroleum reservoir is necessary to early application of proper production practices. A number of investigators have contributed to methods of relating reserves, degree of water drive, and production and pressure history. 1-8 Three types of problems of increasing complexity may be mentioned. If a reservoir is known to have no water drive. and if the ratio of the volume of the reservoir occupied by gas to the volume of the reservoir occupied by oil (which ratio permits fixing the overall compressibility of the reservoir) is known, then only one further extensive reservoir property remains to be determined, namely the magnitude of the reserves. A straightforward application of material balance considerations will permit this determination. The problem becomes very much more difficult if we wish to determine not only the magnitude of the reserves but also the magnitude of water drive, if any, which is present. In principle, a combination of material balance and fluid flow considerations will permit this evaluation. Finally, if neither the magnitude of reserves, the degree of water drive, nor the ratio of oil to gas present in the reservoir is known and it is desired to determine all three of these variables, the problem could in principle be solved by a fluid flow-material balance analysis which determines the overall compressibility of the reservoir at various points in its history. The change in compressibility with pressure would provide a means of determining the ratio of gas to liquid present, since the compressibilities of gas and liquid vary differently with pressure variation. However, in practice this problem is probably so difficult as to defy solution in terms of basic data precision apt to be available.' It is the purpose of this discussion to illustrate the second case, which involves the determination of two unknown variables, single phase reserves and degree of water drive, from pressure and production history and fluid property data, and to study the precision with which these unknowns can be determined in this manner in a particular case. Although an electric analyzer developed by Bruce as used in making the calculations to be described, numerical methods necessary in carrying out the process have been devised and have been applied for this purpose. Schilthuis,' for example, developed a comprehensive equation for the material balance in a reservoir. He combined this with a simplified water drive equation, assuming that the ratio of free gas to oil was fixed by geological data and that a period of constant pressure operation at constant rate of production was available to determine the constant for his water drive equation. On this basis he was able to compute the reserves and predict the future pressure history of the reservoir. Hurst developed a generalized equation permitting the calculation of the water drive by unsteady state expansion from a finite aquifer. He showed in a specific case how the water influx calculated by his equation, using basic geologic and reservoir data to fix the constants, matched the water influx required by material balance considerations. Old3 illustrated the simultaneous use of Schilthuis' material balance equation and Hurst's fluid flow equation for the determination of the magnitude of reserves and a water drive parameter from pressure and production history. He used this method to calculate the future pressure history of the reservoir under assumed operating conditions. As a basis for determining reserves, Old assumed a value for his water drive parameter and calculated a set of values for the reserves, using the initial reservoir pressure and each successive measured pressure. The sum of the absolute values of the deviations of the resulting reserve numbers from their mean value was taken as a criterion of the closeness of fit to the experimental data possible with the water drive parameter assumed. New values of the water drive parameter were then assumed and new sets of the reserves calculated until a set of reserves numbers having a minimum deviation from the average was established. The average value of- the re-

Jan 1, 1949

By E. R. Brownscombe, Francis Collins

A study has been made of the material balance-fluid flow method of estimating reserves and degree of water drive from pressure and production history data. By considering the effect of random pressure errors it is shown that in a particular example a standard deviation of three and one-half pounds in each of ten pressure survey? permits the determination of the reserves with a standard deviation of 8 per cent and the water drive with a standard deviation of 15 per cent, assuming that certain basic geologic data are correct. It is believed that this method of estimating reserves and water drive is useful and reliable in a number of cases. The method is particularly valuable when reservoir pressure data are accurate within a very few pounds, but may also be applied with less accurate pressure data if a relatively large reservoir pressure decline occurs early in the life of the field, as for example in an under-saturated oil field. INTRODUCTION A knowledge of the magnitude of reserves and degree of water drive present in any newly discovered petroleum reservoir is necessary to early application of proper production practices. A number of investigators have contributed to methods of relating reserves, degree of water drive, and production and pressure history. 1-8 Three types of problems of increasing complexity may be mentioned. If a reservoir is known to have no water drive. and if the ratio of the volume of the reservoir occupied by gas to the volume of the reservoir occupied by oil (which ratio permits fixing the overall compressibility of the reservoir) is known, then only one further extensive reservoir property remains to be determined, namely the magnitude of the reserves. A straightforward application of material balance considerations will permit this determination. The problem becomes very much more difficult if we wish to determine not only the magnitude of the reserves but also the magnitude of water drive, if any, which is present. In principle, a combination of material balance and fluid flow considerations will permit this evaluation. Finally, if neither the magnitude of reserves, the degree of water drive, nor the ratio of oil to gas present in the reservoir is known and it is desired to determine all three of these variables, the problem could in principle be solved by a fluid flow-material balance analysis which determines the overall compressibility of the reservoir at various points in its history. The change in compressibility with pressure would provide a means of determining the ratio of gas to liquid present, since the compressibilities of gas and liquid vary differently with pressure variation. However, in practice this problem is probably so difficult as to defy solution in terms of basic data precision apt to be available.' It is the purpose of this discussion to illustrate the second case, which involves the determination of two unknown variables, single phase reserves and degree of water drive, from pressure and production history and fluid property data, and to study the precision with which these unknowns can be determined in this manner in a particular case. Although an electric analyzer developed by Bruce as used in making the calculations to be described, numerical methods necessary in carrying out the process have been devised and have been applied for this purpose. Schilthuis,' for example, developed a comprehensive equation for the material balance in a reservoir. He combined this with a simplified water drive equation, assuming that the ratio of free gas to oil was fixed by geological data and that a period of constant pressure operation at constant rate of production was available to determine the constant for his water drive equation. On this basis he was able to compute the reserves and predict the future pressure history of the reservoir. Hurst developed a generalized equation permitting the calculation of the water drive by unsteady state expansion from a finite aquifer. He showed in a specific case how the water influx calculated by his equation, using basic geologic and reservoir data to fix the constants, matched the water influx required by material balance considerations. Old3 illustrated the simultaneous use of Schilthuis' material balance equation and Hurst's fluid flow equation for the determination of the magnitude of reserves and a water drive parameter from pressure and production history. He used this method to calculate the future pressure history of the reservoir under assumed operating conditions. As a basis for determining reserves, Old assumed a value for his water drive parameter and calculated a set of values for the reserves, using the initial reservoir pressure and each successive measured pressure. The sum of the absolute values of the deviations of the resulting reserve numbers from their mean value was taken as a criterion of the closeness of fit to the experimental data possible with the water drive parameter assumed. New values of the water drive parameter were then assumed and new sets of the reserves calculated until a set of reserves numbers having a minimum deviation from the average was established. The average value of- the re-

Jan 1, 1949

By AIME AIME

TWENTY-TWO sections and all four of the divisions sent delegates to the annual meeting. They became so interested in the wide ranging dis6ussion of old and yet ever-new problems of Institute affairs that three instead of two sessions scheduled were necessary. Monday morning the meeting assembled with President Bassett presiding in the absence of President-elect Tally, who had been called to Baltimore by the serious illness of a brother. Thursday morning Vice-president Turner presided until Mr. Tally appeared after which the latter guided the sessions. Since reports from all of the active sections save one had been mimeographed and sent in advance to the delegates, detailed reports from each were dispensed with. The discussions dealt largely with membership problems, both local and national, with financing, speakers and programs, visits from national officers, and the conduct of the annual meeting. Many interesting and constructive suggestions were made and will be reported back to the sections by the delegates.

Jan 1, 1931

By James F. Kemp

The iron ores of southeastern Cuba present a subject of exceptional geological interest. Their relations to the inclosing rocks are varied and in some cases unusual. The problem of their geological origin is not a simple one and for this reason has occasioned some divergence of views among previous observers. Profiting, however, by these earlier studies and by more detailed field and laboratory observations as well as by the experience of added years of mining, much more satisfactory descriptions and interpretations can now be prepared. Previous Work In 1884, interest in the southeastern coast of Cuba became active among the consumers of iron ore along the Atlantic seaboard of the United States. Active development was undertaken by the Juragua Iron Co., Ltd., a corporation affiliated with the Bethlehem Steel Co., and the Pennsylvania Steel Co. The property of the Juragua company, which is situated about 15 miles east of Santiago, was studied in June and July, 1884, by Dr. James P. Kimball, at the time Professor of Economic Geology in Lehigh University and one of the best known of American mining geologists. Dr. Kimball published on his return two papers, the first important descriptions which we have of the local geology.1 It is

Jan 1, 1916

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By J. E. Walstrom

While intensive research continues to promote a more complete understanding of the potential and resistivity measurements that comprise the electric log, it is believed that consideration should also be given to translating these numerous and often widely separated findings into a coordinated and readable body of fundamental facts designed specifically for the petroleum engineer and geologist. Although provision is made through publication for a ready exchange of new theoretical concepts. it is also desirable to provide reviews and appraisals of the more established techniques and methods from the operating standpoint so that an economic and practical application may be realized concurrently with the theoretical progress. With these basic premises as a guide the author reviews the presnt state of electric log interpretation. The paper is directed not so much to the logging or research specialist as to the petroleum engineer and geologist to whom the electric log is only one of the many tools which he employs. Frequently, these persons do not have the time to follow in detail the many specialized contributions that appear and, as a consequence. are not in a position to place these contributions in proper relation to each other, or to the art as a whole. The paper reviews the basic steps in making quantitative determinations from the electric log of the amount of oil or gas present in subsurface formations and also discusses the degree of reliability of these determinations under various conditions. The paper also indicates the trend of future developments in electric logging systems and methods of interpretation. INTRODUCTION The electric log has been used about 20 years as a means for studying the formations penetrated by a well bore. The first half of this period is characterized by the development of suitable logging techniques and equipment. Although progress in this direction is continuing at a satisfactory rate, the last ten years are characterized more by an increasing interest in methods of electric log interpretation. During this period, a large number of fundamental papers have been published, expounding various logging techniques and particular phases of the interpretation problem. Many of these papers represent important contributions, and a few are classic. This paper is an effort to outline as concisely as possible and in simple terms the main course of progress in electric log interpretation. More specifically, it is the purpose of the paper to review the necessary elements and basic steps used in making quantitative determinations of water saturation from the electric log; and to point out the degree of reliability of these determinations under different conditions. It is strongly advised that the operating staffs of the drilling and exploration departments of oil companies cooperate wholeheartedly with both the electric logging service companies and research organizations in the testing and development of new logging systems and interpretation methods. One purpose of the paper is. however, to indicate the degree of caution which must be exercised in placing confidence in new techniques and interpretation methods that have not been thoroughly tested in the field. It is entirely possible to be cooperative in trying new methods and yet reluctant to believe in the results until the methods are firmly established. It is important to define the meaning of quantitative electric log interpretation. In the most general sense, an interpretation of the log has been made when the electrical characteristics of the formations, as portrayed on the log, have been translated into terms describing the formation geometry, rock type, or any other physical characteristics of the formations. The determination that the top of a sand is at a certain depth is an interpretation of the log. Structural determinations made by correlating electric logs from a given area are also interpretations of the logs. The term quantitative interpretation, however, will be used in this paper in the restricted sense to indicate the determination of the water saturation of a formation. This determination defines the fluid content of an oil and gas productive formation only if the porosity is known, and it assumes that the remainder of the pore space contains hydrocarbons. This assumption is believed to be true for most oil and gas productive formations. The quantitative electric log interpretation may he said to be a determination of the fluid content only to the extent which the water saturation, under the conditions given above. defines it. THE BASIC STEPS The fundamental steps in calculating water saturation from the electric log are: 1. Determination of the true resistivity of the formations from the apparent resistivities as recorded on the electric log.

Jan 1, 1952

By Donald L. Katz

FIFTEEN years ago Dr. Manning published a paper in "Petroleum Development and Technology" on '.Fundamental Research Relating to Petroleum." He tabulated for several industries "the proportion of their present success which can be fairly attributed to the application of information and processes obtained by scientific research," giving petroleum a score of 7 compared to 100 for the electrical and coal-tar industries. Today the petroleum industry as a whole and the producing groups both have raised their score beyond the majority and are climbing toward the top. Present practices are being developed both by fundamental research and the application of the research method in field operation.

Jan 1, 1941

By R. M. Howe, J. Spotts McDowell

Preparation and Use.—Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for bricklaying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining the crude or lightly burned mineral at a temperaturc that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and CO2; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brickmaking in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1/2 to 1 in: (1.25 to 2.5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are Glled. At most plants such holes, at the end of each week, are also carefully filled with dead-burned grain magnesite. For temporary

Jan 1, 1920

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining 'the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By W. S. CAYPLESS, H. O. Hofman, E. E. HARRINGTON

I. INTRODUCTION. LIME-ROASTING is a term proposed by Ingalls 1 for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If, finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse undecomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale, the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the .bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1907

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20&apos; 10&apos; N., longitude, 40 35&apos; w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about &apos;70&apos;. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879

By Charles M. Packer, Oleg D. Sherby, Roy H. Johnson

Originally round tensile specimens of a eutectic Zn-A1 alloy develop elliptical cross sections during superplastic deformation. This observation, coupled with a detailed study of the microstructure and preferred orieniation, suggests that crystallographic slip and continuous grain boundary migration or re-crystallization are important processes during super-plastic deformation. In spite of the extensive activity in superplasticity1-15 and the numerous explanations proposed, no single model has had universal acceptance. It has been established, however, that the general requirements for superplastic extension of two-phase alloys include an extremely fine, stabilized grain size of the order of a few microns, a temperature about equal to or greater than one-half the melting point, a critical range of strain rate, and a similarity in the mechanical strength of the major phases. The proposed models can perhaps best be characterized in terms of the important phenomena associated with them. These phenomena include: phase instability,1 diffusional creep by volume diffusion3 or grain boundary diffusion4,5 slip and continuous grain boundary migration or recrystalliza-tion,= grain boundary Sliding,7-9,13,14 and dislocation glide.&apos;5 In this paper, experimental observations will be reported which support a model involving slip and continuous grain boundary migration or recrystalliza-tion. Specifically, a correlation will be made between this model and the development of elliptical cross sections as originally round specimens are superplas-tically deformed. For the most part, superplasticity studies have been conducted with eutectic or eutectoid alloys. Probably the most thoroughly studied material has been the monotectoid Zn-A1 alloy.1,2,6,12,13,15 No attention to the eutectic Zn-A1 alloy has previously been reported, and the results discussed in this paper represent part of a general study of the superplastic properties of this alloy. MATERIALS The alloys used in this investigation were prepared by melting appropriate quantities of 99.99+ pct A1 and 99.999 pct Zn in air, mixing, and pouring into a water- cooled stainless-steel mold. Wet-chemical analysis was conducted with each heat of alloy prepared, using the procedure of Fish and smith.16 The composition of the eutectic alloy was 95.1 wt pct Zn. Ingots about 2 in. thick were rolled to 0.4-in. plate at about 300°C with a reduction of 5 to 10 pct per pass. Specimens were machined from the plate with the tensile axis parallel to the rolling direction. The specimens were round, with 0.150-in.-diam, 1.25-in.-long gage length, and 0.25-in.-diam threaded grip sections. EXPERIMENTAL PROCEDURE Specimens were mounted inside a uniform-temperature quartz tube which was surrounded by a double elliptical radiant furnace with a 12-in.-long uniform-temperature hot zone and a low thermal capacity. The tube extended through the top and bottom of the furnace and permitted rapid quenching of the loaded specimens when quickly filled with cold water at the conclusion of the test. The quench precluded any effects on specimen microstructure from a normal, slow cool. Constant stress was applied to test specimens by suspending a load on a constant stress cam of the type described by Hopkin.17 The design of this cam permitted application of a constant stress for elongations up to 200 pct. For greater elongation, approximately constant stress conditions were maintained by systematically reducing the load manually. RESULTS As part of an investigation of the superplastic properties of the eutectic Zn-A1 alloy, evidence was obtained for the development of elliptically shaped cross sections as originally round specimens were extended. For example, after an elongation of about 100 pct, a round specimen with an initial diameter of 0.150 in. became elliptical with major and minor axis of 0.128 and 0.88 in., respectively. Photographs are presented to illustrate the ellipticity developed during superplastic deformation, Fig. 1. The specimen shown was deformed at a stress of 500 psi, at a temperature of 285°C, and a strain rate of 2.28 x 10-2 min-1. The strain-rate sensitivity exponent* was measured at *The strain-rate sensitivity exponent, m, is defined as d In o/d In c where o is the steady-state flow stress and E is the strain rate. this temperature and in the strain rate range 10"3 to 10-1 min-1 was found to be about 0.5. This value is typical of those observed with superplastic materials. The material studied exhibited negligible strain hardening during superplastic deformation, the creep rate remaining constant under constant stress and temper-

Jan 1, 1969

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors&apos; laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe&apos;s method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By Charles R. Keyes

the leaching of near-by rocks, had had no other result than to bring out from obscurity three certain features of practical lmport, all the labor of that controversy would have been well expended. These three points are : (1) a clear distinction between the vadose and the profound zones; (2) a determination of the manner in which the latter may be invaded by conditions of the former; and (3) an establishment of the general truth of the lateral-secretion theory when vadose conditions prevail, and of the. ascension-theory under profound conditions. In the practical consideration. of ore-deposits these generalizations are fundamental. Their wider application must be productive of great industrial advantages. Of first importance in the broader scientific survey of ore-genesis is the recognition of a sharp distinction between vadose and profound conditions. To many who listened to Professor Posepny&apos;s remarkable paper, read at the Chicago session of the Institute during the Columbian Exposition in 1893, this seemed, as Dr. S. F. Emmons has already observed, its most valuable and suggestive feature. Notwithstanding Posepny&apos;s implications to the contrary, and his vigorous berating of Sandberger&apos;s views, the immediate and lasting .effect of the . argument was really to strengthen greatly Sandberger&apos;s position. For it completely and sharply separated the lateral-secretionists from the ascensionists, raising the sphere of the former bodily above the line of permanent water-level and at the same time confining .the sphere of the latter to regions below that horizon. A little later, Professor Van Rise showed in some detail how meteoric waters may deeply invade the profound zone and carry vadose conditions into it. The zonal limitations of two great and apparently opposed agencies being thus definitely fixed, it is found that neither of the theories based thereon is susceptible of general application. If the generalizations of the lateral-secretionist be propounded solely for vadose conditions, we are able to agree with all of his more-important contentions; while there is general acquiescence in the views of the ascensionist if their application be restricted to the profound zone. Of the ore-bodies of the world that are mined to-day, the majority are essentially vadose in origin, and probably originated

Jul 1, 1910

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth&apos;s magnetic field vector.

Jan 1, 1975

THIS chapter and the one following deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the simplification of the first two &apos; laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the "heat balance" of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced, and we assume that the cause lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities of flow distribution, air leakage, etc., present in any real, open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained- by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot-metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million B.t.u. per net ton. of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million B.t.u., and the sensible heat in the preheated air at the port ends is 117 million B.t.u. so that the total heat input at the ports is 477 million B.t.u. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million B.t.u., but 120 million of this is supplied by the heat in the hot metal and by various heat--evolving reactions in the bath, so that only 75 million B.t.u. need be supplied to the bath by the flame.

Jan 1, 1944