Search Documents

By K. Adam

Grinding in steel mills adversely affects the flotation of pyrrhotite. The electrochemical nature of inter action between pyrrhotite and active metals was investigated by contacting pyrrhotite with platinum at different applied potentials. Flotation tests, scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were wed to examine the surface properties of pyrrhotite. The formation of hydroxide or oxide and sulfate species of iron through the oxygen reduction reaction at the cathodically polarized surface of pyrrhotite was shown to be the mechanism responsible for the reduced floatability of pyrrhotite.

Jan 1, 1985

By W. W. Eckles

This paper is presented as a suniniary report of the use of well gas composition correlations obtained from mass spectrometer recordings as a means of identification and determination of reservoir continuity. Conventional methods for detecting composition differences are en-pensive, elaborate, and difficult to obtain. This excludes the use of extensive composition data for most applications. During recent years the mass spec-trometer has come into general use as an analytical tool in petroleum refineries. The use of mass spectrometer composition patterns ir~ characterizing or "finger-printing" the produced gas from a reservoir, presents a novel method for correlatitlg gas samples from well to well. The mass spectrometer provides a trace similar to an electric log. having peaks which represent the abuntlnnce of certaitz hydrocarbons in the well gas sample. Without going further into the detailed analysis the idea has been advanced that these traces or patterns could be used as a means of identifying a particular natural gas. This theory has proven to be essentially correct. The mass spectrometer pattern method is simple and cheap as COi?7pared to other standard methods. It greatly facilitates the solution of reservoir and geological problems in which correlation of well gas Com-positions is a factor. Specific field applications have been made. This paper concerns the results obtained in 465 individual gas analyses from 35 fields and 77 res- ervoirs. In a number of cases it has been found that such data have been extremely valuable in the determination of reservoir continuity. In at least one case, the method was a valuable contribution in tracing a reservoir from sand to sand in a coinplex fnulted field involving n11rnerous gas reservoirs. Field applications are presented to illustrate the possibilities of the method at the present stage of developnient and to stimulate the ernployrnent of this new approach by geologists and petroleum engineers in the industry. INTRODUCTION Identification of producing horizons and the determination of reservoir continuity are often a problem in those areas where dome structures and highly faulted sands are encountered. To complicate the picture further, there may be numerous sands, one on top of the other which dip and diverge in different directions. Even though it may be possible to develop some solutions to the preceding problems on the basis of the geological and reservoir data on hand. it is readily recognized that substantiating data based on independent methods would he extremely valuable. It has been found through field studies that correiation of well gas composition can be used to advantage in the geological and engineering study of a complex reservoir identification problem. METHOD FOR COMPARISON AND CORRELATION OF WELL GAS SAMPLES Since a large number of well gas samples are required in a gas identification or reservoir con- tinuity problem, it is necessary that a method of analysis be employed which can detect differences in composition readily and inexpensively. Although detection would be possible by means of low temperature fractional distillation (POD) analpsis, the method requires a relatively large sample and is comparatively slow and expensive to run. The mass spectrometer affords an inexpensive and precise analysis of small well gas samples taken at the surface which are about 1/300 as large as a POD sample. These samples can be obtained by regular field personnei and shipped to the spectrometer for analysis. It is, therefore, a practical approach to the problem. A typical record from the mass spectrometer is illustrated in Fig. I. The peaks on the record represent the abundance of ions produced from the different hydrocarbon molecules making up the gas sam-ple. In well gas comparisons only five peaks are employed, since the other peaks are formed from the same gas molecules and furnish no additional information. The five peaks used represent the abundance of methane, propane, ethane, butane and heavier, and oxygen. They are referred to respectively as the 16, 29, 30, 43, and 32 peaks. The oxygen peak is used to correct for air content in

Jan 1, 1958

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By KING HAMILTON GRAYSON

IRON and steel were the only basic industries in the Soviet Republic in 1928 that lagged behind the pre-war production on a comparative basis. This was due to the almost complete obliteration of all industrial units manufacturing iron and steel products during the Revolution, which resulted in the production of 1921 being only 4 per cent of that of 1913. By the end of 1927 the production of pig iron had reached a point equal to 70.5, per cent of 1913; steel was 84 per cent ; and rolled iron was 78 per cent. According to the. planned program of the Supreme Economic Council, the pre-war level of the iron and steel industry was to have been reached and exceeded during 1929-30. The production of the entire period from 1917 to 1928 in comparison with 1913, is shown in the following table

Jan 1, 1929

By R. H. Winn

In this paper a heterogeneous carbonate reservoir is considered as a succession of layers of formations of radically different porosities, permeabilities, water saturations, and rock matrix types; i.e., the heterogeneity is vertical rather than radial to the wellbore. Presumably each layer is more or less homogeneous. To determine the "net oil in place" in this reservoir it is desirable to know the porosity and water saturation of each layer. In addition, the section must be subdivided into that which will produce oil, that which will produce water, and that which will produce little or nothing. In numerous wells drilled in these reservoirs radioactivity surveys, guard electrode surveys, and caliper surveys have been made. These logs have been compared with core analysis data, when available, and the analysis of the surveys compared with production data. This study, still in progress, is intended to provide improved analytical techniques if such are possible. This paper is a progress report on the work. DETERMINATION OF POROSITY The neutron-gamma log has long been recognized as a measure of hydrogen concentration.1,2,3 In reservoirs that are free of clay, shale, or other hydrogen containing matrices, it has been accepted as a measure of porosity.4,5 Empirical methods to relate relative neu-tron-gamma intensity to porosity are often employed." To provide a more precise determination of porosity from the neutron-gamma log each instrument is calibrated immediately prior to each survey by a method which refers all tools to a hydrogenous cylinder. To insure stability a calibration check is made after each survey. These calibration records are printed as an integral part of the log that is recorded in standard counts per second. A detailed description of the calibration procedure is available in the literature.' The procedure employed insures that each Survey is numerically reproducible within the limits of statistical variation. To relate the standard neutron counts per second to porosity and hole size, records were made in test wells constructed of blocks of limestone. The porosities of the blocks were accurately measured and the blocks completely saturated with fresh water. Fig. 1 presents some of the results obtained in these test wells.' The lines shown in Fig. 1 were obtained by deriving an empirical equation relating the 11 points shown so that the relationship may be projected to larger and smaller hole sizes. A detailed description of the tool is available in the literature.' Field tests indicate that the tool is adjacent to the wall of the hole most of the time when the surveys are made in uncased holes drilled with saline muds. In this circumstance porosity may be calculated from Fig. 1 if the hole size is known. When fresh muds that form thick mud cakes are employed, the centralizing effect of the mud cake must be considered and the porosity determination is less reliable. In cased holes the combined effect of variations in hole diameter and the unknown eccentricity of the casing in the hole may make porosity determinations extremely unreliable. In any event, an accurate knowledge of hole size is essen-

Jan 1, 1958

By J. L. Bray

ACCELERATED programs, as discussed in this paper, refer to the year-around operation of a college or university with three sixteen-week or four twelve-week terms per year, with pauses between sufficient only to allow the administrative group to perform their functions. In most engineering schools, under such conditions, the conventional four-year course can be condensed to two years and eight months. These accelerated programs of study, which now exist in most of our technical institutions, were forced upon us under the influence of the outburst of wartime patriotism, perhaps one might go so far as to call it hysteria. Many of us felt and hoped that these programs were temporary expedients, but the cold hard threat of permanency now rears its head; consequently we should examine the merits and shortcomings of the new order, and evaluate its effect on our educational system, since it may persist in some form in the postwar years, because of the changing political and financial situation. Many engineering students are being educated in state supported institutions

Jan 1, 1944

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

Frank Firmstone, Easton, Pa. (communication to the Secretary*) : It may not be amiss to point out that the top-pressure in iron blast-furnaces is largely affected by variations in the temperature of the gas. I find in my note-books, cases in which the pressure was from 9.25 to 9.5 in. of water when the material in the furnace was low (after dinner-hour), which fell to from 8 to 8.5 in., when the furnace was again full, and the gas consequently cooled. The chief cause for this effect is, that, at the higher temperature, there is a decrease in the weight of the gas in the descending-leg of the siphon formed by the down-comer and the chimneys. It does not seem probable that there is any direct relation between top-pressure and quantity of flue-dirt. Top-pressure, at any given moment, measures the " head " necessary to discharge the gas then passing, against the resistances of pipes, valves, etc., in the gas-conduits between the top of the furnace and the mouths of the chimneys, and can be increased at will by closing, more or less, the valves, or dampers, at the stoves and the boilers. The question of relation between top-pressure and flue-dirt can be settled very easily by direct experiment, working alternately with gas-valves open, and partly closed, and noting the top-pressures and the respective quantities of fluedirt collected. The quantities of fine ore blown away, as shown by Mr. Grammer's tables, are astonishing to one who has had no actual experience with Mesabi ore and hard driving. Flue-dirt, in the sense in which he uses the term, was unknown at anthracite furnaces so long as the working was normal; when it did occur, it was always an incident of scaffolding and bad work, and was no doubt caused by an increase in the velocity

Jan 1, 1904

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By Bjorge, Guy N.

MINING method improve through the gradual process of evolution and in 1340 there were no marked outstanding innovations. On the other hand refinements of detail and betterment: in equipment design continued to progress. Among the most important changes have been the increased application of trucks and highway equipment, including tractors and bull- dozers, to open-pit mining as exemplified by Phelps Dodge's Morenci operations; the Mesabi iron range; and the Tri-State district. Mass or bulk handling contributed its part underground with slurhers and conveyors at Consolidated Coppermines and slushers at Climax; and in open-pit mining. conveyors found increased use on the Mesabi range.

Jan 1, 1941

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By E. S. Moore

The Kolar gold field has been for a long time the most important gold-producing area of India. It is situated in the Skate of Mysore, southern India, and not far from the City of Bangalore. The productive field is about 3 miles long and in it a gold-bearing quartz vein varying in width from 1 in. to over 10 ft. is worked. The vein carries high values to great depths and many of the mines have paid large dividends. Geological Formations In KolaR Region The rocks of the Kolar region are pre-Cambrian in age and bear a close resemblance to some of the pre-Cambrian formations of America. The oldest rocks seen are basic lavas, now mostly altered to hornblende-schists, with which is associated some banded iron-formation; these rocks are similar to the Keewatin schists and iron-formation in the Lake Superior region. The schist is cut by the gold-bearing quartz vein. In certain parts of the area there is also a conglomerate containing pebbles of granite, jasper, and schist. The matrix resembles a hornblende-schist and is intruded by small granite dikes, which in some cases have been pinched off by squeezing of the rock. This has led Dr. W. I?. Smeeth, Chief Inspector of Mines of Mysore, to whom the writer is greatly indebted for information regarding this area and for his hospitality while visiting the field, to regard this conglomerate as a breccia due to crushing of granite dikes in the schist. Dr. J. W. Evans has regarded the conglomerate as probably a squeezed glacial boulder clay. From analogy with pre-Cambrian conglomerates in America, the writer regards it as a metamorphosed rock similar to our basal Huronian conglomerate. However, the main bearing which it has upon the problem under discussion is the apparent fact that it is younger than the schist and that it indicates the presence of a syncline in the rocks cut by the quartz vein. Surrounding the area of schist and conglomerate is a large mass of granite-gneiss resembling the Laurentian gneiss of the Lake Superior region. Still later than the rocks mentioned above are basic intrusions which cut the quartz and schists; in the mines these are known as trap. One dike of this type is 50 to 60 yd. wide.

Jan 1, 1920

By Clarence M. Haight

The general practice in drill sharpening shops, of which descriptions have been written, is about as follows: The bit is heated to 1600" to 1900°F. Then when forged to the proper shape and size in the sharpening machine, the steel is allowed to cool; it is then passed to a hardening furnace where only the end is heated to about 1450" F., and then quenched in cold water, brine, or in brine with oil on top.

Jan 1, 1922

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By Benjamin C. Craft

A review of development in North Louisiana during 1936 centers around the Rodessa field, in Caddo Parish. Continued extension of the

Jan 1, 1937

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934