Search Documents

By August J. Breitenstein, W. Spencer Hutchinson

The outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations are shown for the years 1900, 1930 and 1950 in Table 1. Method or Preparation and Interpretation of Statistical Data The fuels comprised in this study are: (1) the coal group including both bituminous and anthracite coal; (2) the petroleum group, taking in not only petroleum but natural gas and natural-gas gasoline. Natural gas for many years has been used in localities relatively near the wells but statistics were found no earlier than 1910. Demand has rapidly

Jan 1, 1934

By E. C. Harder

Few mineral deposits have in recent years attracted such general and widespread attention as the Brazilian iron-ore depositis…

Jan 1, 1915

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

By T. N. Dixon, J. E. Briggs

A study was made of numerical techniques for solving the large sets of simultaneous equations that arise in the mathematical mode ling of oil reservoir behavior. It was found that noniterative techniques, such as the Alternating Direction Implicit (ADI) method, as well as some other finite difference approximations, produce oscillatory or unsmooth results for large time steps. Estimates of time step sizes sufficient to avoid such behavior are given. A comparison was made of the Point Successive Over-Relaxation (PSOR), Two-Line Cyclic Chebyshev Semi-Iterative SOR (2LCC), and iterative ADI methods, with respect to speed of solution of a test problem. It was found that, when applicable, iterative ADI is fastest for problems involving many points, while 2LCC is preferable for smaller problems. INTRODUCTION With the advent of high speed, large memory, digital computers, there has been an increasing emphasis on the development of improved methods for simulating and predicting reservoir performance. Two-dimensional, three-phase reservoir models with various combinations of PVT effects, as well as gravity and capillary forces, are common throughout the industry. Such models are also available through consulting firms, to anyone desiring to use them. Three-dimensional models will probably be practical in only a few years. We conducted a study of some of the numerical methods used for solving the large sets of simultaneous equations that arise in such models. A typical set of equations for a reservoir model is shown below:

Jan 1, 1969

By Robert Glass Cleland

[DATA OF THE YEAR 1950 COMPARED TO 1909 (FIRST CONSOLIDATED REPORT) CONSOLIDATED NET INCOME Without deduction for depletion of mines $ 42,395,465 $7,337,252 After deduction for depletion of mines $ 4,112,604 $7,337,252]

Jan 1, 1952

Jan 1, 1932

By Uros Bajzelj

To mine very weak carboniferous schists subjected to high ground pressures the underhand cut-and-fill stoping method was proposed using an artificial plate roof. An experimental stope was mined using three consecutive levels. Rock pressures, deformation of the reinforced concrete plate, and the quality of stowing were evaluated. It was found that roof deformations were minimized if the reinforced concrete plate and uncemented backfill were replaced with cemented backfill containing reinforcement near the bottom. The mining method prevented the occurrence of high rock pressures at the face. The method is suitable for mining subvertical ore bodies with large horizontal areas.

Jan 1, 1984

By R. G. Treuting, R. M. Brick

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By R. M. Brick, R. G. Treuting

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By C. D. Keen

IN the latter part of the summer of 1913 the Conservation Commission of the State of Louisiana, under presidency of M. L. Alexander, decided to stop the waste of natural gas going on at the "burning gas-well," located about 3/4 mile southeast of Oil City, La. On several occasions, both in newspapers and in reports, comment had been made on the condition of this well, its harmful effect on the Caddo gas field, and the considerable loss, estimated at several thousand dollars each month, caused by the escape of the valuable fuel. But nothing had been done to bring the well under control and prevent further waste of gas until the State Conservation Commission took the matter in hand. The gas fields of Louisiana are among the greatest in the country. So far most of the gas has been found in the Caddo field proper, although considerable development has been done in and around the city of Shreveport and near the town of Mansfield in DeSoto parish. To extend the life of the gas fields and to prevent the quick exhaustion of the supply of the natural fuel are matters of vital importance for this section of the country. Four gas companies have entered the Caddo field and supply the surrounding towns and cities with gas. The Arkansas Natural Gas Co. has pipe lines to Little Rock, Ark., and supplies gas to the following cities and towns in that State: Texarkana, Hope, Garland, Emmet, Prescott, Boughton, Beirne, Gurdon, Arkadelphia, Gum Springs, Malvern, Donaldson, Gifford, Perla,- Beaton, Beauxite, Mabelvale, Bryant, Sheridan, Pine Bluff, Little Rock, Argenta, Pulaski Heights, and Hot Springs. The Southwestern Gas & Electric Co. transports gas to Mooringsport, Blanchard, Caddo, Rodessa, Oil City, Vivian, Bloomburg, Hosston, Ida, Dixie, Belcher, and Shreveport. The Marshall Gas Co. supplies gas to the town of Marshall, Texas. The Louisiana Co. has a line to Shreveport.

Jan 3, 1914

By D. P. Seraphim

Single crystals of bee Li-Mg solid solution were grown and their internal friction was measured as a function of temperature, A peak of the Zener type was found in the damping spectrum. The activation energy for the relaxation process is 21.5 ± 1 kcal per mole and the frequency factor is 1015.7 ± 0.7 sec-1. ZENER internal-friction peaks which are observed for a wide range of solid solutions are attributed to stress-induced changes in local order.' In the present work a Zener internal-friction peak, the first reported for a solid solution of an alkali metal, is

Jan 1, 1961

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

In a previous article' the authors outlined a study I of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated.

Oct 1, 1955

By J. F. Lazenby, W. F. Abercrombie

The role of the laboratory is described in relation to the prospecting and exploration of kaolin clays. Test method's used to evaluate crude ore samples of kaolin clay for commercial consideration are reviewed. A background of the kaolin mineral and known means of prospecting this mineral are presented. Common analytical methods are discussed with special emphasis on those in use today.

Jan 1, 1983

Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'3S) Min. Engr., Dir., Bu¬ reau of Mines. Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch, Morenci. Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Ten¬nessee Coal Iron & R.R.. Co., 1542 Brown -Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Command¬ing, Officer, Pittsburgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D., (M'32) Alin. Engr.. Div. of Cor¬porations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur, Ga. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co., Led., Vatnkoula, Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Bans. Abernathy, Jack H., (M'40) Peer. Engr., c/o Superior Oil Corp., National Bank of Tulsa Bldg., Tulsa, Okla. Aborn, Robert H., (M'10) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'39) Peer. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles, Calif. Abramowitz, William L., (J'40) Chem., Industrial Inventions, Inc., 103 Foster Se., Peabody, Mass.

Jan 1, 1942

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material

By S. Maemura

Miike Colliery of Mitsui Coal Mining Company, the biggest and oldest coal mine in Japan, is producing a quarter of the national coal production, about 5.2 million tons of clean coal annually and almost a half of which is now being mined under the "slicing Mining System". The slicing system is a mining method to mine a thick coal seam dividing it into two faces, upper and lower. Its history started nearly 20 years ago. However, the all-around modernization of this system has made little progress up to recent years, while mining methods for single longwall faces has made a remarkable progress together with the improvements in mining machineries, self advancing supports and so on. The reason was that the tremendous difference in adaptabilities of mechanized face equipments existing between the upper and lower faces has made it very difficult to increase the total production capacity of slicing system. After our persistent study for seventeen years, we have recently realized successfully the quite satisfactory slicing system, applying the combination of shield type self advancing supports and double ranging drum cutter at both faces. We are now fully convinced of that the high efficient, quite safe and improved slicing system has been basically established for the present. This paper intends to brief the transition on the combination of self advancing supports and mining machines, its results and further to detail the development of shield type self advancing support for upper face and artificial roof material which shall be the key point to be successful in full mechanization of slicing faces.

Jan 1, 1976

By Y. Zimmels, I. J. Lin, I. Yaniv

The potential application of magnetic and electric separation techniques in beneficiation of fine-particle feeds are reviewed. Special features of these techniques are considered and compared with a view to increased amenability of such feeds to separation in electro- magnetic fields. The following techniques are discussed, with reference to those already developed and in use to-date: - Differential-susceptibility separation (DSF). - High-gradient differential-dielectric separation (HGDDS). - High-gradient magneto-gravimetric separation (HGMGS). In this context the new approach - whereby selectivity of solid- solid separation processes, in wet high-gradient magnetic and electric separation, can be improved - is described, including experimental results from DSF and HGDDS tests.

Jan 1, 1980

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) IN vol. 33 of the Proceedings of the Institution of Civil Engineers, London (part 2, for 1870-71), may be found a statement of the cost of two blast furnaces, together with a somewhat detailed description. The attempt will be made in this note to restate these items of cost, so that the information may be rendered perhaps more accessible to our members than in its present place of record, and also in order that the items may be more intelligibly compared among themselves, or with similar items in other cases.

Jan 1, 1878

By M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evalu-ated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable; from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0:03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper' of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evalu-ated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable; from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1936