Search Documents

By Eliot Blackwelder

For the purposes of this paper, the boundaries of China and Siberia will be taken as they stood about 1907. Except in the Caspian region, it is doubtful if all the oil ever produced in these countries would equal one day's flow of a good Texas well. Considering the vastness of the regions and the variety of strata, it seems strange that these two countries should have made so small a showing in the petroleum industry. No doubt the condition is caused partly by lack of prospecting and of modern methods of development; in larger measure, however, it is evidently because of unfavorable geological conditions over nearly all of east-central and northern Asia. CHINA The known oil occurrences in China are very few. For many years, perhaps a barrel a day has been obtained by primitive methods from wells near the city of Yenchang in the northwestern province of Shensi. A like amount was obtained from wells bored for salt water in the vicinity of Kiating in southwestern Szechwan. The little oil was separated from salt water by allowing it to stand in jars. The salt wells yield also considerable natural gas, which is used to evaporate the salt and also for domestic purposes. There is evidence that wells were bored in this part of China before the third century. It is said that more than 1200 wells have been sunk in that district to depths of 1600 to 2000 ft. (485 to 610 m.) in connection with the salt industry. The scarcity of petroleum in China may be ascribed to three general geologic conditions: First, China contains practically no marine sediments of Mesozoic or Cenozoic age; second, the Paleozoic sediments are not for the most part of the types that generally contribute petroleum; third, the rocks of nearly all ages have been strongly folded, faulted, and more or less intruded by igneous rocks in all parts of China except certain areas in the west and northwest.

Jan 7, 1922

By John Fritz

Gentlemen of the American Institute of Mining Engineers : I desire to thank you sincerely for the distinguished honor you have conferred upon me by electing me to the presidency of this society, a position which in the past has been filled by some of our most distinguished and ablest members, men eminently qualified by education, practical training and a business ability which has enabled them not only to fill the position with credit to themselves, but as well with honor to the society. In deference to a custom long established, by which the presidentelect is expected to read a paper on some subject with which he is more or less familiar, I have thought that a brief review of the methods employed in the manufacture of iron, as witnessed by myself, and reaching back to 1838, would interest some of our older members and give our younger ones a glimpse into the trials and difficulties encountered in those early days by the pioneers in this great industry. In 1840, 12 to 20 tons of pig-iron was the make of a furnace per week—at this time from 1200 to 2000 gross tons. In 1840, 3 to 4 tons No. 4 wire rods per turn. They have lately made 176 gross tons in 11 hours. In 1840 I have not the quantity of puddled iron made; but it was

Jan 1, 1895

By C. W. Allen, L. C. Moore

THE Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming, on the Marquette iron- range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleveland-Cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. GEOLOGY The north footwall of the Marquette Range synclinorium outcrops near the north line of sec. 2, the iron formation dipping to the south at an angle of about 40º. The south side of the trough reappears at a distance of 4 ½ miles on sec. 26 and the surface geology between shows iron formation or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 per cent P, 5.40 per cent Si, 2.87 per cent Al and 0.015 per cent S. EXPLORATION A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1945

By C. W. Allen, L. C. Moore

The Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming. on the Marquette iron range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleve-land-cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. Geology The north footwall of the Marquette Range synclinorium outcrops near the north line of set. 2, the iron formation dipping to the south at an angle of about 40. The south side of the trough reappears at a distance of 4J5 miles on sec. 26 and the surface geology between shows iron forma- tion or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850 ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 Per cent P, 5.40 per cent Si, 2-87 Per cent A1 and 0.015 per cent S. Exploration A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1946

By J. J. Gilman

Examination showed that characteristic cleavage step patterns are observed on the cleavage surfaces of undeformed, slipped, bent, twinned, compressed, and indented zinc crystals; and the effect of temperature is discussed. Dimples were seen to produce cleavage steps in a treelike pattern in otherwise undeformed crystals. The steps seem to originate when cracks intersect screw dislocations. IT has been known for a long time that the path of fracture in polycrystals may be discontinuous (see Jaffe, Reed, and Mannl for review). Recently, Kies, Sullivan, and Irwin2 have proposed, and given evidence, that crack propagation is discontinuous within individual crystals as well. Other evidence has been given by Low.' When discontinuous cracks within a crystal join together to make a macrocrack, the lamellae between each set of two cracks are torn somewhere, forming small cliffs. These cliffs appear as lines when the cleavage surface is observed microscopically.4,5 The lines have been called vein, tree, and riverlike markings by various authors, and they have sometimes been mistaken for fissures. The descriptive term cleavage steps is used in this paper. Cleavage steps vary in height over a wide range of values, from molecular dimensionsG to lor. and larger. Kies, Sullivan, and Irwin,2 as well as George,' have shown that the gross cleavage step patterns for plastics, polycrystalline metals, and for mono-crystals are sometimes similar. Thus, they depend mostly on the mechanical variables that prevail during cleavage and are relatively insensitive to the structure of the material. For example, parabolic markings2,7,8 sometimes result when cracks open up ahead of, and not coplanar with, the main crack front. If the advance crack has the same velocity as the main crack, their intersection line is a parabola, otherwise it is a hyperbola or an ellipse. The patterns are strongly affected by differences in crack velocities. This results in chevron patterns which point to the place of origin of the main crack. It is the purpose of this paper to demonstrate the existence of a mechanism of cleavage step formation which is a continuous rather than a discontinuous process. Also, certain characteristic step patterns are described, and the strong effect of temperature is shown. The specimens were zinc monocrystals (grown from 99.999+ pct pure metal). These were cleaved at room temperature and at — 196°C. Results and Discussion Cleavage step patterns are highly variable from point to point on a given specimen, as well as from one specimen to another. Although the patterns shown in the photographs are typical, they have been selected for graphic illustration. Figs. la and lb compare undeformed crystals that were cleaved at —196 °C and room temperature, respectively. Cleavage at room temperature (Fig. lb) resulted in a higher density of high steps (dark black lines) and enhanced the visibility of the fine background markings. Deformation by simple slip caused no marked change in the step patterns until the glide strain reached about 1.0. But, as Fig. lc shows, the density of high cleavage steps was greatly increased by large glide strains. Corrugations lying perpendicular to the slip direction may also be seen in Fig. lc. These are caused by deformation bands. The cleavage resistance of the crystal of Fig. lc was very high compared to undeformed crystals (estimated by the force on a needle required for cleavage). Striking and varied cleavage step patterns were observed on bent crystals. Two characteristic patterns that were observed on crystals bent at 25°C, and cleaved by reverse bending at —196°C, are shown in Figs. 2a and 2b. The first, Fig. 2a, consists of V-shaped lines similar to the parabolas of other materials2,7 Fig. 2b shows a pattern that is the equivalent of Fig. la, consisting of faint background lines with a few higher step markings. Cleavage of bent crystals at room temperature resulted in Figs. 2c and 2d. Now, the cleavage step lines show a strong tendency to follow one of two perpendicular paths. In Fig. 2c (bent once), many of the cleavage step components that lie parallel to the bend axis are assembled into irregular lines. In Fig. 2d (bent twice), the cleavage steps again tend to consist of two perpendicular components, but neither of the components is assembled into lines. Also, the step density is higher.

Jan 1, 1956

By AIME

VERSATILITY is perhaps the outstanding characteristic of the subject of this sketch. He is author, golf-player, musician, public speaker, philatelist, German scholar, and has been a school teacher; but these are incidental. Oliver Ralston's professional forte might be described as beneficiating solid minerals and he has dealt in an important way with practically all of them. To this work he has brought a fertile mind stimulated by keen imagination but kept on the track by a sense of economic balance. An indication of his versatility is evidenced by his career with the Bureau of Mines, which he first joined in 1912, when the Bureau was just one year old. Except for two excursions into industry-Hooker Electro Chemical Co. (1917-20) and United Verde Copper Co. (1928 to 1935)-his entire professional career has been with the Bureau.

Jan 1, 1946

By John B. Knaebel

The annual Jackling Award Lecture, sponsored by the Society of Mining Engineers of AIME, is intended to honor and commemorate one of the greatest mine-makers of all time, an innovator whose vision and determination made ore out of waste rock. He ushered in a new philosophy of mining which revolutionized some segments of the industry and notably affected our economy generally. To have been asked to given the Jackling Lecture this year is an honor that I scarcely deserve, but which I have accepted in humble gratitude. Although it is true that "many a mine has made the man," it is also true that while ore bodies are found, mines are made. That statement has been hammered into my skull many times by a man whose own career exemplifies its truth, a man who has been first and last a steadfast friend, who for a while was my boss and mentor, and who as one of this country's great mining geologists has laid his hand to the making of many a mine. I will doubly cherish the memory of the honor bestowed upon me because the presentation of the Jackling Award was made by this man. After the Lord made Dick Hunt he threw away the mold. Metals and other mineral products are essential ingredients of the social economy of the modern world. No well informed and thoughtful person can doubt that they will be indispensable to mankind as long as the fabric of civilization as we know it today can be held together. They are mined from ore bodies, which, unlike some other kinds of bodies, are physically inorganic and wholly incapable of reproducing themselves. Since in time they become mined out, an endless procession of new producers must be made by someone if the fundamental needs, to say nothing of the not so fundamental whims of an affluent society, are to be gratified. In saying that these mines must be made, I mean exactly that. It is my purpose to comment upon some of the problems we must cope with in making them. I shall try to avoid dwelling needlessly upon aspects of new mine development with which most people in this business are thoroughly familiar, and will attempt to discuss in a useful way some of the newer and more significant features of the economic climate in which these endeavors must be conducted. To begin with, an Almighty force put the ore into the ground, and selected the places in which to put it. Mankind was not consulted. Beyond that stage, however, mankind must find the ore deposits and contrive to extract their contents and put them into useful service. In doing this, he must use tools and techniques devised by man to overcome obstacles created in part by nature, but also in part by man himself. And most importantly of all, in making the tools and applying the techniques, he must use people. In the whole process the most pliable ingredient at hand-and also the most unpredictable-is people. Mines play out, and men die. As time goes on, we will have new mines, and they must be made by new men. The Environmental Dilemma It is perhaps timely to touch first upon the newest and in many ways the most potent consideration affecting the feasibility of developing new mines-the problems related to protection of the environment and to the

Jan 1, 1973

The Telfer Project, one of the world's newest gold mines, is located about 300 km (190 miles) northeast of the Mt. Newman iron ore project in the northern part of Western Australia. The first mineral claims were staked in 1972; and by mid-1975 ore reserves of 3. 8 million mt (4. 19 million st) of 9.6 g per mt (0. 28 oz per st) ore had been indicated. It is interesting to note that Newmont spent more than 10 years and A$10 million in Australia for extensive mineral exploration before finding the Telfer deposit, and then spent approximately A$3 million in exploration and feasibility engineering on Telfer. Including this A$3 million, a total of A$27 million was spent to complete construction of the mine, village, gold treatment plant and associated roads, airport, water and services. Over 50% of the capital cost is in the metallurgical facility, or approximately A$10, 000 per ton per day. All economically significant gold mineralization at Telfer occurs in a series of layered quartz-limonite reefs in which the former pyrite has been oxidized to limonite to a depth of 100 m (330 ft). The most important gold reef occurs at the base of the siltstone-shale horizon within the enclosing sandstone dome -like structure. At the Main Dome structure the dipping ore horizons will be mined to a vertical depth of about 60 m (200 ft) by open-cut methods. The waste-to-ore ratio is approximately 12:1. Eventually 44 million mt (48. 5 million st) of ore and waste will be mined. Mining of the waste is by contract; however, the ore and a thin layer of waste is company-mined. Dilution from mining the geological ore reserve is about 10%. The ore is completely oxidized and the gold occurs free within the reef, material as discrete particles of varying but mainly fine grain size. Most of the gold is "free milling"; that is, over 50% of the gold is coarse enough to be recoverable by gravity concentration. Two duplex mineral jigs receive the two cyclone underflows from the grinding circuit. The rougher jig concentrate is up-graded on a continuous strake from which the concentrate is tabled to produce a final free gold product. Jig tailings are returned to the ball mill and the concentrates are amalgamated. Gold amalgam is pressed, retorted, and melted into gold bars. The gravity gold recovery circuit is the same as was used in many of the gold mills in California in the 1930s.

Jan 1, 1981

By P. Bolsaitis, L. Skolnick

Vapor pressures of silver over ternary alloys of six different copper to gold ratios have been measured by means of the Knudsen effusion technique. The data obtained in the temperature range of 1330° to 1375° have been used to estimate the integral excess free energies of the ternary alloys and the activities of copper and gold. The results compare favorably to the predictions based on the electron cell model of alloys recently formulated by the authors. THE orifice effusion method for measuring vapor pressures of materials in condensed phases was first introduced by knudsen, and has since been used extensively for the determination of thermodynamic properties of condensed phases. The basis of the measurement is the effusion, through a small orifice, of vapor in equilibrium with a condensed phase. Assuming free molecular flow into high vacuum, the vapor pressure, P (in mm Hg), of the effusing species is calculated from the following equation:' where w (g) is the weight of effusing species lost during a run, t (sec) the time length of the run, A, (sq cm) the area of the effusion orifice, T ("K) the temperature at which the run is conducted, M the molecular weight of the effusing species, and k the Clausing factor, a constant that corrects for deviations from free molecular flow caused by the finite thickness of the orifice walls.17 The determination of partial and integral thermodynamic variables from vapor pressure data of ternary alloys is possible only if the vapor pressures of all but one component are negligible or can be esti-

Jan 1, 1969

By Joseph L. Gillson

Bentonite, designating a distinct type of clay, is a young name in mineral nomenclature in the light of the age-old names of most other useful nonmetallics. The earliest references in literature are to "soap clay" (1873) "taylorite" (1888) and finally "bentonite" in 1897, from its occurrence in the Fort Benton series of rocks near Rock Creek, Albany County, Wyoming. Bentonite is a rock term and consists largely of montmorillonite clay. The latter name was proposed in 1847 for a plastic clay found at Montmorillon, France. A clay of apparently identical properties was described by Cronstedt of Sweden in 1788 and a number of other similar clays found in France were given other names in publications from 1853 to 1856. The mineral name montmorillonite was recognized by Dana in 1892. The recognition of "clay mineral" distinctions which led to the present-day classifications of clays by their chief mineral content, dawned in the early part of the twentieth century. Grim6 has aptly said: About 1924, Ross10 and some colleagues of the U. S. Geological Survey began a study of the mineral composition of clays that led to a series of monumental papers on the subject. By the early 1930's what has come to be known as the clay-mineral concept became firmly established in the minds of a great many people actively studying clay materials. The clay mineral concept designates the major clays as kaolins, montmorillonites and illites and by this concept bentonites are now defined as "fine-grained clays containing not less than 85 pct montmorillonite" and a wide variety of clays found all over the world are included in that classification. They could all properly be called "montmorillonite clays" but the common commercial name is bentonite. For a period of over forty years from the time of the earlier discoveries, bentonite was thought to be only the sodium type highswelling clay produced principally in Wyoming. By the clay mineral concept, non-swelling montmorillonite clays also became known as bentonite. In the trade there are two broad divisions-sodium bentonite, often called Wyoming or "western," which expands in water and carries sodium as its predominant exchangeable ion, and calcium bentonite often called "southern," which has negligible swelling and carries calcium as its principal exchangeable ion. There are many intermediate gradations. Properties The mineralogy and chemistry of the clays are so complex that the subject cannot be summarized briefly. The reader is referred to Chapter 12 of this volume in which the subject is treated at some length. Grim6 gave the formula for montmorillonite as (OH)4Si8AL4020.nH2O. He wrote: Montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. . . . Exchangeable rations occur between the silicate layers. . . . The words "tetrahedral" and "octahedral" refer to the coordination number of the cations in the unit cell in the crystallographic lattice. Carroll5a stated: That the montmorillonite structure is the same as that of mica, but the layers are not held together by K+ ions; and water and other polar molecules, such as organic molecules, can enter between the unit layers and cause expansion. Ex-

Jan 1, 1960

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. INTRODUCTION Buchans is 5 miles north of Red Indian Lake, in Central Newfound- land, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller- town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Ch, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.1 The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north- central Arkansas. Miser has described the geology and manganese mineralization in some detail.2,3 The rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,4 Fernvale lime- stone and Cason shale, are host rocks of the primary manganese mineralization.

Jan 8, 1959

MARCH 15-Industry is rapidly snapping back from another coal crisis, other business news is in general favorable and the outlook through the Spring is by most observers considered quite promising. Most industries report comfortable backlogs of unfilled orders, department store sales in recent weeks have equalled in dollars those of the corresponding period last year, retail sales of automobiles show again over the same period a year ago, and new orders for machine tools are at the highest figures since August 1946. Orders for railway freight cars have shown a very encouraging pickup, with a total of 9385 cars in January and the N. Y. Central alone ordering 4500 in February. Construction continues very active. In January new housing starts totaled 80,000 against 50,000 a year ago and the daily average contract awards, according to the Dodge reports, were 57 pct larger. In the first 22 days of February the increase in awards was 27 pct. Lumber orders since Jan. 1 have run 22 pct above last year. All of these favorable factors bolster the opinion that the upturn in industrial output and employment which began last summer has not yet spent itself and that the setback caused by the strikes will be made up when people get back to work. Only in a few lines are there indications that primary production may be outrunning the consumption of finished goods, although inventory build-up would seem to be rather modest as the National Association of Purchasing Agents reported in February that 78 pct of its members were buying for 60 days or less. Industrial prices as a whole show no significant trend despite the continued alarm over both the immediate and the long-term possibility of inflation caused primarily by the government's increasing expenditure and its inability to balance the budget. A recent advance of 1.9 pct in primary market prices is viewed by some people as the surface symptom of renewed inflation, but even so it is more than two years since the alltime high was reached by the daily index of sensitive commodities in November 1947. Over two years have passed since prices received by farmers hit their peak and about a year and a half since all wholesale prices and the consumer price index touched their highest points in August 1948. The decline in the wholesale price index has been almost continuous, interrupted only twice by slight advances in the monthly figures from February to March 1949, and, later in the year, from August to September. Of course, this continued decline in the last half of 1949 largely reflects a downward movement in farm and food prices. Wholesale prices for commodities other than farm and food leveled out after June and now stand only slightly under the June level. Farm products are down by 22 pct from January and by 18.6 pct from August 1948. Food prices are down only slightly less. Consequently, the farm price support program is in serious trouble and has imposed a heavy financial burden on the Treasury. In those commodities other than farm products only building materials, chemicals and textiles have come down as much as the average, while housefurnishings and metals and their products have fallen hardly at all. Glancing away from the domestic front, the results of the British general election indicated a highly inconvenient situation, that public opinion there is so exactly deadlocked as to divest the victors of much ability to make forceful decisions or create significant policy. It is generally considered that another election in the near future would give substantially the same result. The British people are equally divided and the politicians are not likely to precipitate another appeal to the country until there is manifest reason to believe that external and internal circumstances have changed sufficiently to permit one party or the other to obtain a decisive verdict. Because of the lack of a clear mandate steel nationalization will likely lag in Britain. In the meantime there is considerable discussion going on as to whether the European steel industries as a whole are at a disadvantage in world competition with the American industry. An article in the "Statistical Bulletin" for January of the British Iron and Steel Federation takes issue on this point with the authors of the Geneva report, observing that they wrote before devaluation, and this particular conclusion "has been overtaken by events." The "Bulletin" also contends that the statement was in any case incorrect so far as Britain was concerned, and that it was based on scanty and insufficient evidence. To support the rebuttal a detailed and extensive comparison is made of the home prices of certain steel products in Britain and in other countries of the world. The accompanying table gives a selection of the prices published. It sets out the changed position since devaluation and since the recent increases in American steel prices. These are home market prices; no doubt in competitive export business some of the price levels could be brought closer together at need.

Jan 4, 1950

By P. J. Jorgensen, J. H. Westbrook

The anomalous indentation creep of nonmetallic solids is shown to be due to the presence of adsorbed water. Although a specific mechanism is not proposed, it is suggested that the water may be present in two chemically adsorbed states. DEPENDENCE of the indentation hardness of solids on the time of load application was first studied systematically by Hargreaves1 in a study of lead and certain low-melting alloys. This technique has become known as indentation creep and has been exploited particularly by underwood and by Mulhearn and Tabor3 as well as by others.4°7 For metals good correlations have been found between the time dependence of hardness over several orders of magnitude in the seconds range and creep parameters from conventional tests at the same temperature where creep strains were measured over hundreds or thousands of hours. However, Walker and Demer8 and Mitsche and Onitsch9 observed extensive indentation creep at room temperature (particularly for light loads) in certain minerals and in materials such as lithium fluoride and magnesium oxide for which conventional creep is ordinarily not observable unless the testing temperature is at a very much higher fraction of the melting point. Normal behavior was observed' for metals such as copper, i.e., negligible time-dependent flow during room-temperature indentation. Walker and Demer attempted to find some distinctive difference in the surface deformation markings about indentations in the anomalously behaving materials at short and very long indentation times. No significant differences were observed. Increased duration of loading was found, however, to result in an increase in the length of glide of edge-dislocation loops extending into the interior of the crystal. Jorgensen and Westbrook,10 in a recent study of

Jan 1, 1965

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

JOSEPH DANIELS, Seattle; Wash. (communication to the Secretary*). Mine models are of great value to the student and to the layman in visualizing underground conditions, and, in a measure, should be just as much a part of the equipment of a mining school as sets of ore specimens, catalogs, or drawings. The chief drawback, as Professor Stock has indicated, is the time and cost of making them. The greatest good in the development of the model comes to the person who makes it, and I have often wondered whether it might not be possible to have each student make one model during his undergraduate career. At the University of Washington we have been collecting sets of mine timbers, made of 6 by 6-in. lumber, illustrating shaft, level, and stope timbering. This work has been done by freshmen. Perhaps each educational institution could specialize in the creation of a certain type of model and exchange its product for that of another school, just as we now do with ore collections. In this way we could build up good museums at a relatively low cost. JOHN R. CHAMBERLIN, New York, N. Y. (communication to the Secretary?).-The type of model described by Professor Stoek is admirably suited to exhibits of coal mining in horizontal veins, and fulfills perfectly the three purposes mentioned. As an educational illustration in colleges, especially when the students themselves build the model under the direction of their instructors, it is of the highest value; and as each condition in mining requires special methods to depict properly in a model, the student is compelled to exercise considerable inventive resource to construct a true representation, stimulating the imagination and interest in his subject. Models built for exhibits in lawsuits are usually constructed to show prominently some particular feature of vein formation or geology, or the relation of underground workings to surface property lines, and as such their use is invaluable to the successful litigant. When the litigation is ended, it is natural that the model should be relegated to the basement and frequently destroyed, as data on underground workings are often considered of a private character by the operators; and it is

Jan 10, 1917

By Hertha R. Freche

The diffusion of magnesium and silicon from the core into the high-purity coating of Alclad sheet is important commercially, and led to the use of a duplex product for the study of diffusion by means of spectro-graphic analysis of successive layers. It has been found that in the duplex materials the diffusion of magncsium from an undersaturated aluminum-magnesium alloy into its high-purity aluminum coating is approximately of the same order of magnitude as the diffusion of silicon from a saturated aluminum-silicon alloy into its high-purity aluminum coating. However, if magnesium and silicon are both present in the alloy in the ratio of Mg2Si, they appear to diffuse in the approximate ratio of this compound. Finally, if the alloy contains silicon in excess of the amount required by magnesium silicide, the amount of diffused silicon in the high-purity aluminum coating will also be in excess. The interdiffusion of metals in the solid state is of both scientific and technical interest, because it is helpful in the study of the alloy structure and in the solution of problems pertaining to the strength and surface condition of the fabricated product. W. C. Roberts-Austenlt carried out the first quantitative determination of the coefficient of diffusion of gold into lead. This classical experiment was followed by a series of investigations on the diffusion of metals and nonmetals in iron and steel and in nonferrous metals and alloys. Recently the diffusion of copper in coated strong aluminum alloys was investigated by A. Burkhardt2. This appeared to be the first published investigation on the diffusion of metals into aluminum. The present investigation was the direct result of a technical question in connection with alloy fabrication and is a summary of some preliminary work pertaining to the diffusion of magnesium and silicon into aluminum. The results necessarily will be subject to some variations, since this is the first attempt to evaluate the coefficients of diffusion of magnesium and silicon into aluminum according to this method of procedure. This

Jan 1, 1936

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener's estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5'9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener's result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970