Search Documents

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By W. L. Dennen, V. H. Wilson

THIS paper is a description of the opera¬tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery of The Hudson Coal Co. during the first nine months of operation and follows a pre¬liminary description given at the Anthracite Institute in May, 1947, in a paper titled "Preparation of Anthracite Sift for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size operating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig 1 and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which handles the Breaker waste water. This underflow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped .to vibrating screens where the plus 316-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine

Jan 1, 1948

By Eckley B. Coxe

I WISH to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market.

Jan 1, 1879

By S. A. TAYLOR

THE aftermath of a world war brings up a number of economic problems for the consideration of all thinking and patriotic citizens. The solution of the problems which confront the country at this time cannot well be accomplished by reference to past experience, for such conditions as confront us today have not existed in the past. We must, therefore, in any attempt to solve the present problems, rely to a great extent upon a careful analysis of present conditions to determine what is wrong; and after this is determined, seek the remedy and apply it. It needs no argument to establish the fact that, in the effort to win the war, the cost of so doing, and the waste in connection with it were, to a large extent, lost sight of; and this situation caused high wages, high cost of all materials, and of food supplies.

Jan 1, 1921

By T. M. Anderson

Open pit mining at Inspiration began in 1947 after 32 years of underground mining. Two separate pits are included in the operations: the Thornton pit, which measures approximately 2500 x 2000 ft, and the Live Oak pit, which is 1500 x 3000 ft. The geographic centers of the two pits are approximately 4000 ft apart, and at the closest point, the two slopes are only 500 ft apart. Today, much of the open pit mining is being carried out in areas which were broken by earlier underground block caving operations; less than 50% of the total material moved has required drilling and blasting. In the solid or virgin areas, the, material ranges only from soft to medium hardness, thus simplifying drilling, blasting and loading operations. As a result, most mining costs and problems have been centered around truck haulage, truck maintenance and the ever-increasing length of the grade haul.

Jan 3, 1963

By D. B. Kibler

THE Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Albertus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to 1-yd. capacity. Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating. These

Jan 1, 1941

By D. B Kibler

The Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Alber-tus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. Early Mining The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to I-yd. capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas power- I house near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939 approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore 1 they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for I the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today i only three companies are operating. These

Jan 1, 1942

By D. B. Kibler

The Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Alber-tus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. Early Mining The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to I-yd. capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas power- I house near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939 approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore 1 they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for I the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today i only three companies are operating. These

Jan 1, 1942

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley' in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By Eugene Guccione

One of the world's most respected scientists, Dr. Hans A. Bethe (see box) has concluded that if anything can solve the energy crisis, it will be coal and uranium. "It is an illusion to think that we can solve our problem by energy conservation alone. For the next few years, conservation must play a very important role, but at the same time, we must see and develop all our alternative energy sources," he said. In his series of five lectures on the energy crisis, given at the University of Utah while he was visiting professor there during February 1974, Dr. Bethe examined all the existing and newly proposed energy sources. He very quickly ruled out solar power, wind power, and tidal power. Solar power, he said, would be 3% to 4 times more expensive than nuclear energy and would only make sense in tropical areas; wind power, which could at best produce one-tenth as much energy as solar, is "for the birds;" and tidal power, which can be exploited in only a very few coastal locations, is "for the fish."

Jan 5, 1975

By Roger A. Harris

INTRODUCTION The Kidd Creek Mine produces a total of 3.6 million tons annually. Geologically the orebody is complex, containing rich values of zinc, copper, silver and lead which are mined and milled as two separate "ore types". Production is mainly from highly mechanized sub-level open stopes of approximately 300,000 tons each. The Mine Engineering Department has developed, and now operates, a computer system that is the subject of this report. It was created specifically to aid the daily work of the mining engineer and has features that are new and possibly unique in the industry. DESIGN OBJECTIVES In 1971 a task force, set up to investigate the subject of computer assistance to mine engineering, specified four design requirements which it felt a successful application had to satisfy. They were:- 1) The computer had to offer a TOTAL SYSTEM that was fully integrated into the routine mine engineering function. 2) The computer had to be directly usable by the current engineering staff, the majority of which had received no formal training in computing.

Jan 1, 1977

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By R. A. L. Black

13.8-1. Introduction. Table 13.8-1 shows that production from the African continent is an important part of total world mineral production. In three of the major particular resources listed, diamonds, gold, and cobalt, African production accounts for considerably more than half the world output. Overall, South Africa including South West Africa plays a dominant role in the mineral economy of Africa, other than in petroleum production. Table 13.81 also shows that much of the production is won by surface mining methods. In addition to the minerals listed in Table 13.8-1, Africa is a main world source for the following minerals: [Beryl 33% of total world production Columbium-tantalum 50%" " 1' Platinum group metals 20% l' " 11 Corundum 55%" " " 11 Vermiculite 30% (' " (6 Uranium oxide 15 0/, of free world production] South Africa and Rhodesia together account for nearly all of this production, except for columbium (niobium) of which Nigeria is the main producer. Thus the importance of southern Africa as a major mineral province can readily be appreciated. The consequences of serious political or military conflict between white-dominated southern Africa and the rest of the continent would be grave indeed, particularly for the West whose financial and economic interest in Africa as a whole is very large. The development of mineral resources in Africa involves the same basic elements as are involved anywhere else in the world: exploration, drilling and sampling, metallurgical assessment, and economic evaluation before, if it is justified, a prospect is brought to the productive stage. The same range of factors controls the economic viability of a project in Africa as elsewhere, of which the most important are:

Jan 1, 1968

By James P. Graham

In this paper the authors present the background information to preheating and its development and describe the facilities available at the British Carbonization Research Association. The results obtained at BCRA including those collected during commissioning of the new plant at BCRA are summarized and reference is made to the research work planned for the next stage. The enlarged test-plant facilities at the British Carbonization Research Association embrace both 10-t (4.2 m high) and 17-t (6.5 m high) test ovens and two types of preheater, the preheated coal being charged by either gravity or pipeline. During the commissioning of the new equipment, an extensive programme on preheating was initiated and the paper includes the results obtained so far. These cover tests on wet and preheated coals and commercial blends, the use of Rosin- and Cerchar-type preheaters and charging by both gravity and pipeline systems to the 10-t and 17-t ovens. Accordingly, for the first time a direct comparison is possible of both the performances of the plants and the qualities of the respective products. The paper also outlines the findings from a study of the carryover of solids during the charging of preheated coal and of the treatment of those solids.

Jan 1, 1977

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would require too much space. The remainder of this discussion, therefore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. GEOLOGY The first, from the historical view, is geology in its relation to the mineral industries. Previous chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering so overlapped one another that men who were by, training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in geology as a pure science, and who perhaps took a doctor's degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would- not be questioned, even though they did not take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1939 and reports for the same year of the following standing committees: Admissions, Membership, Papers and Publications, Mining and Metallurgy (Magazine), Library, Speakers for Local Sections and Student Societies, and Student Relations. These reports present additional details. Membership.-For the second year in Succession membership reached a new high level for all time, as indicated in the accompanying tabulation in which "Members" includes all categories except Student Associates. [END 1938 END 1939 NET GAIN Members9, 57 610, 163 587 Student Associates 2,898 3,760 862 12,474 13,923 1,449] Net gain in membership (aside from Student Associates) was 587 compared with 744 in 1938, despite the fact that applications received in 1939 exceeded those received in 1938 (1271 against 1162). The smaller net gain is accounted for in three ways: (1) A greater lag in enrollment of those elected in the last quarter of the year; (2) an increase in the number of applications involving change of status from Junior Member to Member; and (3) an increase of 167 in the loss by death by resignation and by suspension in 1939 as compared with 1938. Experience shows that at the end of a year of less prosperous conditions in the mineral industries, and, therefore, among engineers engaged in these industries, resignations and suspensions are more numerous. Business and industrial indexes all show 1938 to have been somewhat less prosperous than 1937; but the improvement in 1939 should be reflected in the record for 1940.

Jan 1, 1940

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f'racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,' have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961