Search Documents

By P. Duwez, H. Martens

Dimensional changes generally occur during the sintering of metal powder compacts. These changes may have several causes and their magnitude depends upon the numerous variables involved in the process, such as the nature of the powder, size and shape of the grains, compacting pressure, rate of heating, maximum temperature, length of time at temperature, and furnace atmosphere. Among all the variables, time, temperature, and compacting pressure are probably the most important ones, and the effect of each one of the other variables can be studied separately once the effect of these is well understood. The most precise method of studying the phenomenon of dimensional changes in a compact consists of heat treating the compacts at various temperatures for different lengths of time. In this method, only very small specimens can be used, in order to achieve rapid rates of heating and cooling. The technique involved in these measurements is very simple, but is time consuming. Another experimental approach to the problem consists of measuring the change in length of a compact as it is being heated at a constant rate. Although the two variables, time and temperature, are combined into a single one (rate of heating), the results obtained by this technique may be of great interest from both practical and theoretical points of view. The purpose of this paper is to describe a systematic investigation of the change in length during sintering of compacts made of one or several metal powders. Experimental Procedure The change in lenght of compacts during sintering was measured with an automatic recording dilatometer. In this instrument the change in length and the temperature are recorded as functions of time on two separate charts and the rates of heating and cooling may be varied from 1 to 20°F per min. The temperature may be kept constant at any value up to 2200°F during any predetermined length of time and the change in length recorded as a function of time. Provision is made for atmosphere control inside the fused silica tube containing the specimen. Three different magnifications are provided, so that 1 in. on the chart corresponds to 0.002, 0.005, or 0.010 in. change in length. The mechanism following the change

Jan 1, 1950

By G. B. Gould

THE softening temperature of coal ash, as determined in the labora-tory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfail-ing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heat was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investiga-tions that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at tem-peratures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a hetero-geneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening tem-perature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion.

Jan 1, 1940

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By Whitmell J. Smithwick, Charles E. Dandois

The first operating unit of the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany was rated 185 tpd and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are under construction or on order. Sizes range from approximately 100-330 tpd, however, units of over 500 tons are in the design stage. The ring shaft kiln is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping (Fig. 1). Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc., are mounted at the kiln top and at the bottom of the kiln is the silo with a vibrator type discharger. Mounted separately is the required blower for injector air and fan for internal cooling.

Jan 4, 1973

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By Byron B. Morton

NICKEL-BEARING alloys are associated with petroleum in the fields of exploration, production, and refining. In the first- named field the geologist of today makes use of such instruments as the seismograph, torsion balance, and magnetometer, the selection of proper alloys and metals for the manufacture of which is an important matter. Nickel-bearing alloys are useful for parts that require resistance to corrosion or that must have non-magnetic properties. Where special co- efficient of thermal expansion are de- sired, they are obtained by using alloys high in nickel (20 to 60 per cent), since, by varying the nickel contents, alloys can be obtained ranging fro111 "Invar", with a low expansion between -40 and 175 cleg. F., to those with coefficients of expansion exceeding that of steels. The latter are obtained by additions of chromiurn to the alloys. Alloys containing 50 to 80 per cent of nickel, which possess high magnetic permeability, find application in certain instruments where this property is important.

Jan 1, 1935

By Robert L. Zerga

Mining equipment and systems have been incorporated into the San Manuel mine to meet the requirements of ore development and extraction. A general discussion of the existing equipment as it relates to the specific methods is presented. A comparison is made between original and present equipment, and future equipment needs. The problems, successes and failures of mining equipment adaptation for the San Manuel mining system are highlighted.

Jan 1, 1981

By Paul M. Tyler

MARKETWISE the year 1935 was rather a good one for most of the rare and minor metals; as a class they climbed out of the depression much faster than the common metals. The diamond market, too, was better than it had been for years, attributable only in part to investment buying, as there was a genuine pick-up in consumer demand. Wars and rumors of war tended to speed up purchases of certain metals, but consumption for peaceful purposes was the principal factor. Significant was the important role played by new industrial uses. New discoveries during the year were disappointingly few, considering the broad extent of this research frontier. Scientific developments were far from being at a stand-still, of course, but the dominant note was the cashing in on research consummated in former years. With even a moderate upturn in general business a surprising number of laboratory ideas donned overalls and found jobs in industry.

Jan 1, 1936

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By B. H. Caudle, L. G. Davies, I. H. Silberberg

This paper presents a method of predicting the recovery and performance of a five-spot steam injection project, in which a realistic approach to pattern sweepout efficiencies is made. Published methods for radial systems were modified for the five-spot pattern by approximating the stream lines with straight lines radiating from the injection well and then converging to the producing well. In each radial segment, the position of the steam front and the temperature profile ahead of the steam front were determined by heat balance equations, which included an estimation of heat losses to surrounding formations. The location of the saturations behind the cold water front was determined from a Buckley-Leverett solution to the material balance equation. Results from this program show steamflood recovery in a five-spot pattern to be considerably less than that predicted for true linear or radial flow systems. For a specific reservoir containing 900-cp oil, a steamflood in a purely radial flow system was predicted to recover more than 75 percent of the original oil in place when 2 PV of water had been injected as steam. A five-spot steamflood with otherwise identical properties was predicted to recover 10 percent of the original oil in place when 0.15 PV of water had been injected as steam and to recover almost no oil thereafter. A cold water five-spot flood in this system was predicted to recover approximately W percent of the oil in place with I PV of water injected. For a five-spot pattern in an example reservoir with 10-cp oil, steam injection similarly showed lower ultimate recovery than water injection but no improvement in recovery rule. Introduction The thermal recovery method considered in this study is steam injection in a five-spot pattern. Pattern steam injection has been given little attention in the past, possibly because of some rather obvious disadvantages. Unless steam temperature is maintained throughout the entire swept area, the process will revert to simple waterflood with all heat being lost prior to reaching the oil bank. Also, the oil viscosity reduction takes place near the steam front and not around the producing wellbore, so that low producing rates must still be endured. This is the reason for the success of the steam stimulation, or cyclic injection, in which the fluids are produced from the same well used for injection. On the other hand, steamflooding can offer some advantages. Oil displacement is by four methods: (1) mechanical displacement by the condensed water, (2) viscosity reduction of the crude oil, (3) swelling of the crude oil, and (4) distillation of the crude oil in the steam zone. Although dependent upon the crude, laboratory experiments have shown displacements up to 80 percent by steamflooding. In addition, steam is a good heat transport medium, since it is cheap and has a high heat content. Previous Investigations Previous publications have reported methods for predicting recovery in a steamflood for linear and radial systems. Since no pattern sweep efficiency is taken into consideration, the recovery even from a radial system must be greater than from more realistic geometries such as the very common five-spot patterns. Probably the broadest coverage is given by Willman who reported experimental results and offered a method of predicting recovery for a radial flow system. They concluded that both hot water and steam injection recover more oil than an ordinary waterflood, and that steam injection could yield recoveries "as much as 100 percent greater than by water flood." They also concluded that both the heat requirements for a reservoir and the residual oil remaining in the reservoir after steam injection were independent of the amount of oil originally in place, that short exploitation times were desirable, and that a high percentage of net sand in the reservoir with a high initial oil saturation was desirable. The method assumes that the flood occurs in three concentric cylindrical zones: (1) an inner steam zone, (2) a central hot water zone, and (3) an outer cold waterflood zone. Displacement in the steam zone is based on laboratory-determined residual oil saturations while the hot water and cold water zones use the conventional Buckley-Leverett equations. Although the results shown by Willman et al. are for a radial system flowing out from the well to an assumed external circular boundary, their equations did

Jan 1, 1969

By W. A. Anderson

Recrystallization of cold-worked metals has long been known to proceed by a process of nucleation and growth.' When a cold-worked metal is heated to a temperature at which recrystallization will ensue, nuclei of new grains, essentially strain-free, appear and grow. As the process proceeds, nuclei continue to appear and to grow, until the cold-worked matrix has been entirely consumed and recrystallization has been completed (Fig. I). Conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time, yields an isothermal recrystallization curve, showing the time course of the recrystallization process (Fig. 2).2 Evidently, then, the rate of recrystallization is determined by the rate at which nuclei form and the rate at which they grow. The rate of nucleation N is the number of nuclei that form in unit time in unit volume of the unrecrystallized matrix, and the rate of growth G is the increase in radius of the recrystallized grain per unit time. In recent years attempts have been made to determine N and G as these vary with the well-recognized variables affecting recrystallization: time, temperature, degree of deformation, etc.1 Such studies yield information that is more fundamental than that conveyed by the conventional recrystallization diagram,' since the rate of recrvstallization is thus analyzed into its two component rates3 Methods are now available by which N and G can be measured, and analytical expressions have been developed for the interrelationships among N, G, the isothermal recrystallization curve, and the final grain size, which greatly facilitate analysis.2-4 The application of these methods has been demonstrated recently for the recrystallization of silicon ferrite.2 Data on N and G in dependence upon the recognized recrystallization variables are, however, very fragmentary;" values of N and G have been determined for some metals, but the effect of temperature, which would yield the fundamentally important activation energies, has been too little studied. Thus far there has been no detailed study of the recrystallization of any one metal in terms of X and G ovcr appreciable ranges of the variables time, temperature, degree of deformation, and original grain size. It is the purpose of the present paper to provide such a study, employing aluminum.

Jan 1, 1945

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By John I. Yellott

SINCE the days of Newcomen and Watt, when men first sought to turn the energy of fuels to useful purposes, coal-generated steam has supplied most of the power needed for both stationary and mobile applications. The low efficiency and large water requirements of the nineteenth century steam-power plant caused many engineers to turn their thoughts toward more direct means of converting heat into power. As far back as 1791, John Barber secured an English patent on a combination' which he might well have called a "gas turbine." He proposed to generate procducer gas from coal or charcoal, to burn it under pressure in air obtained from a reciprocating compressor, and to drive a turbine wheel with the resultant hot combustion products. With the optimism characteristic of the inventor, he hoped that the turbine would not only operate his compressor but also perform useful work. There is no record that Barber ever built his machine, but if he had done so he would have learned that useful power can result from such a combination only when both turbine and compressor are highly efficient and when the temperature of the gas entering the turbine is not far below 1000°F. Hot-air prime movers continued to attract attention, and both Stirling in England and Ericsson in America2 built reciprocating engines that operated with some success upon coal-heated air. The internal-combustion engine, burning liquid fuels, supplanted the hot-air type, and, for the first time, challenged the supremacy of both the steam cycle and its familiar fuel, coal. LIQUID FUELS COMPETE WITH COAL As the increasing use of the automobile multiplied the demand for gasoline, the supply of residual fuel increased rapidly, and heavy oil declined in price to the point where it became competitive with coal. First in the marine field and later in stationary plants in areas adjacent to refineries, oil began to be widely used. Oil's greater convenience and higher heating value per pound of weight or per cubic foot of bunker space have caused it to take over much of the marine field. The introduction of the highly efficient diesel engine, capable of burning a fuel that is cheaper than gasoline, again threatened the position of coal, for the operating costs of the diesel became directly competitive with those of coal- burning equipment. In isolated power plants and smaller marine installations, the diesel provided the medium by which oil again successfully invaded fields formerly dominated by coal. The diesel engine, provided with an

Jan 1, 1946

By Walter Wood

The specifications for cast-iron pipe that have been submitted at this meeting are practically the outgrowth of those which were originally adopted, about 1860, by Mr. Kirkwood of Brooklyn, N. Y. They have been changed but little since that time, the mode of testing pipe in the hydraulic press, as well as the method of coating, not having departed from the original practice. The chief addition to the specifications has been in the adoption of a test-bar 2 in. by 1 in. in crosa-section, broken between 24-in. supports by a transverse strain applied on the flat side. Test-bars were first introduced into pipe-specifications about 1870. At that time a satisfactory test-piece had to stand a tensile strain of 16,000 lb. per square inch. The present test-bar was adopted in order to give some idea of the deflection of the iron that was being used. These deflection-tests have been so satisfactory to both engineers and manufacturers, and have met the requirements of the pipe-trade so accurately, that it is considered best to hold to the . 2-in. by 1-in. bar instead of adopting the short " Arbitration Bar," which yields but little information from the stand-point of deflection. The new feature in these specifications is the effort to reach standards to which pipe shall be cast in the future, thus permitting the manufacturer to make up stock and the purchaser to find material on hand when he asks for deliveries. Heretofore there has never been ally standard weight for pipes? although in some sizes certain weights are more frequently asked for than others. The fixing of standards for pipes permits the adoption of definite standards for fittings. It has been aimed to secure such uniformity for fittings as will permit the same class of fittings to cover two or more classes of pipe. In order to accomplish

Jan 1, 1905

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960