Search Documents

By S. F. Shaw

The Seminole field was first drilled in 1913. During the next 10 years other attempts were made to discover oil in this field, but without encouragement until March, 1926, when the Indian Territory Illuminating Oil Co. completed NO. 1 Dyer in the Hunton lime for 1100 bbl. On July 16, 1926, the Independent-Garland interests discovered oil in the Wilcox formation when No. 1 T. Fixico came in at 4055 ft. and on Sept. 9, 1926, production reached a peak of 8040 bbl. On Aug. 1, 1927, the daily production of the pools making up the Seminole district amounted to slightly over 500,000 bbl., practically all of which was coming from the Wilcox formation. The Hunton formation has not been very productive of oil, but has maintained a fairly high gas pressure; this formation has been encountered at from 3800 to 4200 ft., below which there is about 100 ft. of Sylvan shale. The shale is underlain by 75 ft. of Viola limestone in a few places in which formation oil has been encountered. Below the Viola lies the upper Simpson formation in which is found the Wilcox sand. The depth of the Wilcox in the Seminole field varies from 3900 to 4500 ft., and initial production has reached as much as 12,000 bbl. The gravity of the oil is about 41° Be. The general practice is to set 6 5/8 -in. casing above the Wilcox and drill in, though in several cases 5 3/16-in. casing has been set for the oil string, and in a few instances, casing as small as 4 3/4 in. has been employed. Production Statistics Production for the Seminole district for the various months since its discovery is shown in Table 1.

Jan 1, 1928

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By W. A. Hockings, D. W. Fuerstenau, A. L. Mular

This paper briefly describes a simple air pycno-meter and its use for rapid determination of the composition of mixtures of solid particles. Research on such problems as the pelletizing of solids, the mixing of solid particles, and the comminution of mixtures can be simplified by means of this analytical tool. THEORY OF OPERATION Liquid pycnometers1 are commonly employed to measure volumes. These devices are time consuming and sometimes give inconsistent results. The liquid used in the pycnometer may have an undesired influence on the material to be measured; moreover, complete displacement of air by the liquid is seldom

Jan 1, 1963

By DONALD H. McLAUGHLlN

Few factors have had more influence in maintaining the strength and stability of the United States than our persistent habit of providing .checks and balances to the dynamic powers of free enterprise on the one hand and to the controls and guidance exercised by the State on the other. .Indeed, it is this same concern for matching forces against each other that has given our republic its ability -to preserve a democratic basis of life for its citizens, and yet maintain a ,government that is able to protect the rights of all and to resist and minimize the danger of excessive concentration of authority. Our current efforts to clarify the nation's mineral policies and to define more clearly the role that the governmental agencies should play in conjunction with the functions of private -enterprise again reveal the desirability and advantages of maintaining our traditional controls. At times, the equilibrium has been temporarily disturbed by too great enthusiasm for one or the other of these basic concepts. Sooner or later, however, the balance has been restored by the healthy opposition that is always created by excesses of one sort. At the current stage in our history, the swing toward undue enlargement of the powers of the State seems to have gone dangerously far and we would be untrue 'to our traditional behavior if the group that must demonstrate the virtues of free enterprise did not rally to its support with the utmost earnestness.

Jan 1, 1949

By H. B. Pulsifer

ONE of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition.

Jan 1, 1931

By George A. Laird

THIs old and once famous district played, through its enormous production of silver and gold, an important part in the history of the State of San Luis Potosi. According to a pamphlet prepared under the direction of the Governor of the State, Sr. Don Blas Escontria, and presented to the visiting members of the Institute during the Mexican meeting of 1901, this district is situated 20 km. east of the city of San Luis Potosi, in a range of mountains of moderate height, extending 135 km. N. and S., and 16 km. E. and W.; and the mineralized area hitherto developed is about 600,000 sq. m. The history of the district, as given by the record dated 1778, and formerly kept in the Sail Francisco convent, says that it was discovered in 1575 by Sr. Don Pedro Irarte, and adds that the city of San Luis Rey de Francisco de1 Potosi received its name (in allusion to the famous Potosi mines in Bolivia) by reason of the remarkable productiveness of its gold- and silver-mines in the first period of their exploration, during which they paid to the Crown, as quintos (the fifth part of the product), $97,000,000, as appears from the accounts of the royal treasury. The amount of the quintos paid during the " bonanza period " of 80 years was $72,000,000. The larger sum first mentioned probably represents a longer series of years. But either will suffice to indicate the great wealth of the mines. In 1663, the decadence of the industry began with the caving-in of several mines, concerning which the record of 1778, already cited, says, in substance, that on Good Friday one of the owners in the enterprise, in view of the unfavorable prospect of a lawsuit in which he was engaged, set fire to the timbers supporting the underground galleries and workings of the Sail

Jan 1, 1905

By Mark David Rankin

This paper represents a general assessment of the primary factors driving the market for mobile offshore drilling rigs and the utility of those factors as choice variables for the offshore drilling program planner.

Jan 1, 1982

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By W. L. Zeigler

DURING the middle 1880s, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddies. Later Wilfley tables took the place of sand jigs and vanners superseded the buddies. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. TAILINGS DISCHARGED INTO STREAMS From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1947

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By AIME AIME

ANDREW FLETCHER, newly elected Treasurer and Director, has spent his entire mining career in the employ of the St. Joseph Lead Co. and brings to the Institute Board a career rich in financial experience and varied in interest and accomplishment. "Drew" Fletcher was born in New York City on Feb. 6, 1895. After graduating from the Sheffield Scientific School of Yale in 1916 as a mechanical engineer, he became a shipyard mechanic in Wilmington, Del. The next thirteen years saw. him gradually enlarging his responsibilities until he ultimately became the head of the W. & A. Fletcher Co., in Hoboken, N. J., ship repairers. In 1929 his program for merging the Fletcher plant with five other New York shipyards was finally consummated in the formation of the United Dry Docks, Inc., which subsequently was purchased by Bethlehem Steel, with the result that today the old Fletcher yard and organization has been expanded into one of the finest ship repair units in the United States.

Jan 1, 1944

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By William Priestley

The author has shown, by .practical experiments, how the rate of cooling steel in the mold governs ingotism, segregation, the formation of dendrites, and the distribution of intergranular material; and the resulting effect these conditions have on the physical qualities of the steel before annealing, after annealing, and after forging. The paper also describes how the structure of steel is affected by the design of the mold and the method of pouring. It is shown that the various constituents of carbon steel segregate differently under different rates of cooling. For the classes of steel covered in this paper, it is concluded that the best physical structure and the most uniform chemical composition is obtained by pouring the steel at a low temperature and solidifying as rapidly as possible in the mold. MUCH time has been devoted, by metallurgists, to the study of steel after solidification and remarkable strides have been made in the heat treatment of steel, but less knowledge is available of the thermophysical, activity of the constituents of steel prior to solidification in the mold. It is known that certain elements added to steel produce marked changes in physical properties, also that other elements added to steel produce similar changes, but we have only meager knowledge as to how these elements combine in steel under different conditions of solidification. It is not sufficient to know, from chemical analysis, that a certain element is present in steel. We should know how this element is in combination with the other elements and whether the combination is such as will give the greatest physical properties. Certain elements go into solid solution with the iron, while others segregate to the grain boundaries and combine with the impurities collected there. Until it is known where an alloy produces the most beneficial effect and a means, is determined for controlling its physical location by altering solidification conditions, or otherwise, we will not obtain the maximum value from our alloys.

Jan 2, 1924

By Marvin P. Barnes, John G. Simos

The Park City District, Utah, is situated in the Wasatch Range at the intersection of the westward extension of the axis of the Uinta Range. Ore has been mined almost continuously from the first discovery in 1869 to the present day, with a total production of over 14 million tons. Sediments of Carboniferous to Triassic age have been folded into the northerly plunging Park City anticline and subsequently modified by thrust faulting, diorite and diorite porphyry intrusions, and strong east-west normal faulting during the Laramide orogeny. Younger andesitic volcanics partially cover the eastern edge of the district. The ore bodies occur as both lode and bedded replacement deposits over widely scattered localities. Near surface, high-grade silver "bonanza" ores were mined in early days from the Ontario and Daly Lodes, which occur along the east-west zone of faulting near the center of the district. Other lode or fissure deposits were found along the Mayflower and Hawkeye faults to the east and southeast. Large bedded replacement silver-lead-zinc ore bodies associated with east-west zones of fissuring, have been mined from favorable horizons in the Park City Formation in the Daly West and Judge mines. A series of long, narrow, high-grade, replacement ore bodies occur in the Silver King mine at a single horizon in the Park City Formation. Ore is currently being mined from strong bedded replacements in the Humbug Formation near the apex of the Park City anticline. Factors controlling ore deposition are: magmatic source, structural feeder systems, and favorable host rocks. Ore deposition along favorable beds is primarily a function of physical conditioning and secondarily of chemical composition.

Jan 1, 1968

By Henry A. Wriedt, John Chipman

Equilibrium in the reaction of hydrogen gas with oxygen in liquid nickel, iron, and their alloys has been studied at temperatures of 1500° to 1700°C. The equilibrium con^stant, 0/p, [% O], is greater in nickel then in iron by a factor of 45 at 1594 C. In the alloy steel range, the activity coefficient of oxygen is slightly increased by the presence of nickel. NICKEL is more resistant to oxidation than is iron, in both the solid and the liquid state. The solubility of oxygen,' however, is greater in nickel than in iron. The two metals and their liquid alloys constitute an interesting series of solvents in which the chemical behavior of oxygen can be studied by methods similar to those used for liquid iron.' Experimental Method The furnace assembly, including the tube for preheating the entrant gas, was the same as that described by Gokcen and Chipman. " controlled mixture of water vapor, hydrogen, and argon preheated to approximately the melt temperature impinged upon the surface of the liquid metal. The charge, weighing about 35 g, was held in an alumina crucible at constant temperature in the gas stream for a prolonged period, then quenched in a stream of cold helium, sampled, and analyzed for oxygen by the vacuum fusion method. The temperature of the liquid metal was measured by a Leeds and Northrup optical pyrometer which had been checked against a similar instrument certified by the National Bureau of Standards. The freezing point of electrolytic iron in hydrogen, taken as 153j°C, was used for frequent checks. This point and the emissivity determined by Dastur and Gokcen" established the transmissivity of the optical system. The emissivities of Fe-Ni alloys at 1535" are known from the experiments of Smith and Chipman,h nd it was assumed that the variation with temperature is parallel with that of iron. Recorded temperatures are probably accurate within k5"C. Preparation of Gas Mixtures—Since the ratio H,O:H, had to be much higher for nickel than for iron, it was found convenient to construct two separate systems for gas preparation. In both cases, the ratio of argon to the sum of the other two gases was at least 4, the proportion of hydrogen and water vapor being varied to produce H,O:H, ratios from 0.2 to 70. The primary purpose of the argon was to diminish the errors caused by thermal separation' in the gas phase. In addition, its presence lowered the saturation temperature required for a given H,O:H, ratio and minimized the difficulty of preventing condensation. Both systems were modifications of the one used by Dastur and Chipman.' For H,O:HI ratios greater than 2, welding-grade argon purified by passage over magnesium chips at 620°C was mixed with hydrogen produced in the electrolytic cell shown in Fig. 1. The design was based on a cell used by Bodenstein and Pohl," the important features of which area nickel wire cathode and sodium hydroxide solution as the electrolyte. The rate of hydrogen evolution was controlled by a calibrated ammeter and a rheostat in the circuit, the current efficiency being taken as 100 pct. Precise control of the argon flow rate at about 300 ml per min was achieved by means of a capillary flowmeter having a controlled pressure drop. The molar flow rate was measured volumetrically before each run, and a constant flowmeter setting was maintained thereafter. The A-H, mixture passed through a water saturator of the type previously described," the saturation temperature being maintained automatically with a fluctuation of k0.04"C. The tube between saturator and furnace was heated by a resistance winding. The system was of all Pyrex construction with the exception of the stainless steel tube containing magnesium chips. This was connected with the glass tubing at the upstream end by

Jan 1, 1957

By P. J. Connors, William J. McCormick, F. B. Olender, Jerome F. Sheldon, Donald T. Mylar, Edgar T. Gregory, Owen S. Roberts, H. Colijn

A quiet revolution has taken place in the conveyor belt industry. Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry. Formerly the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Monofilament rayon, with desirable elongation and elastic properties, was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon.

Jan 3, 1972

By Robert Gilman Brown

The original power-plant of the Standard Company has been described* by Mr. T. H. Leggett, late president and manager of the company; but since the presentation of his paper considerable additions have been made, which will be found interesting because of the engineering features involved and of the attainment of a high degree of flexibility with the inflexible, two-wire, alternating system of electrical transmission. Although these additions have been completed during the last year, they constitute, to a large extent, only the carrying out of plans that belonged to the original conception of the installation. The regular operation of the water-power through the winter proved very difficult; there was a considerable length of ditch to be kept open, and, as the stream is small and any freezing night may stop the whole flow of water, there was the .additional trouble of having no reserve to draw upon. The rule for the winter is, that after a night of hard frost water begins to move in the canon before noon on all but the coldest days. To obviate the nuisance of the anchor-ice, and to make available all of the water, a dam of sufficient height to impound several days' run of water has been built across the canon, 3875 feet above the power-house, and provided with pressurepipe well below the surface. In place of the 1571 feet of pipeline from penstock to power-house, there has been substituted a line 3875 feet long to bring water direct from the dam. The dam is of logs, cribbed up in squares of about 12 feet, ballasted with earth and rock and sheathed on the water-face with 3-inch plank.

Jan 1, 1897

By W. F. Netzeband

Jan 1, 1927

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979