Search Documents

By G. R. Gardner, D. H. Davis

INCREASING realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. CLASSIFICATION OF DUST SOURCES The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these-namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By V. F. Zackay, W. A. Goering

ALLOYS of iron and aluminum up to 35 wt pct aluminum are single-phase solid solutions, and are of potentially wide applicability.1-3 In spite of early and continued interest1-4 little progress has been made until recently in the preparation and evaluation of sound alloys containing more than 6 wt pct aluminum. Vacuum-melting techniques for the production of ductile Fe-A1 alloys have been described recently.1-7 A. procedure for air melting these alloys is presented here. Low-carbon iron is induction melted without a slag in a rammed magnesia crucible. At the beginning of melt-down, aluminum pig (99.95 pct Al), charged in a clay-graphite bottom-pouring crucible is placed in a pot furnace at 1800°F. The primary deoxidation of the molten iron after melt-down is effected by the addition of 0.1 pct aluminum and 0.5 pct manganese. (Hilty and Crafts" have reported a significant increase in the deoxidation efficiency of the aluminum and manganese combination over that of the aluminum alone.) A more drastic deoxidation designed to reduce the oxyen content to the lowest possible level is accomplished by plunging metallic calcium to the bottom of the melt. This is done by wiring small cubes of the metal to a steel rod. A circular shield larger than the diameter of the crucible opening is attached to the rod so that any spa'ttering of the molten metal will not endanger the operator. Since the temperature of the molten metal is above the boiling point of calcium, the bath is vigclrously purged by calcium vapor. It is believed that the calcium-vapor treatment permits a homogeneous distribution of calcium in the melt. Owing to the vigor of the reaction the temperature of the molten metal should be kept below 2900°F prior to the calcium addition. A total of 0.05 pct calcium is added in two stages in this manner. The second calcium deoxidation is made just before charging the molten aluminum into the iron, in order that an excess of calcium be present for the remainder of the melt. The aluminum, which has been removed from the holding furnace, is then hydrogen degassed by bubbling chlorine through a quartz tube immersed in the molten aluminum. The hydrogen-chlorine reaction is an exothermic one preventing the solidification of the aluminum during the 5-min chlorination. Approximately 0.1 pct calcium, based on the amount of aluminum, is then added to the aluminum. A further excess of calcium is introduced into the melt in this manner. The oxide dross is removed, fluorspar is added to the molten iron, and the molten aluminum is poured through the fluorspar slag. The fluorspar should be dried thoroughly prior to its use, as any water present will react with the aluminum. Aluminum oxide formed during the pouring operation reacts with the fluorspar slag to form gaseous aluminum fluoride and calcium oxide. A forced-draft ventilating system is required for this operation as aluminum fluoride is toxic. As soon as the molten aluminum has been added, vigorous manual stirring of the melt is required because the slag-aluminum oxide reaction is highly exothermic and tends to take place near the top of the melt. The combination of high temperature and the slagging action of the fluorspar quickly erodes the crucible at the slag line if the aluminum is not stirred uniformly into the melt. It has been found that at least 4 min of manual stirring combined with induction stirring are necessary to ensure homogeneity. The power is shut off 1 min prior to pouring to allow metal and slag to separate. As much slag as possible is removed from the melt, which is then poured directly into cast-iron molds. A mold wash of aluminum oxide is used to prevent ingot sticking. For slab ingots which are to be rolled into sheet, a carbon-tetrachloride vapor atmosphere or a chlorinated-pitch mold wash is desirable, as the aluminum oxide formed in the pouring operation is subsequently removed by the chlorine in the presence of carbon." As in vacuum melting, a pouring temperature of about 2900°F is recommended. Adequate hot-topping is important as iron-aluminum ingots are subject to very deep piping. Ingots are removed from the molds and buried in vermiculite, where they are allowed to cool slowly to room temperature. The ingots are radiographed,

Jan 1, 1959

By W. E. Rice

THE ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick .wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no, grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700° F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces along, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users -of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By T. K. Redden

Protective coatings based on the formation of a surface coating of nickel aluminide (NiAl) were applied to the nickel-base superalloys IN 100, SEL 15, and U-700. Coated specimens were exposed to an oxidizing environment at temperatures between 1600 and 2200 F for times up to 1000 hr. The oxidation resistance and stability of the coating were evaluated by weight gain measurements, metallographic examination, and X-ray diffraction study of surface oxides and coating. The composition of the coating and diffusion zone was determined by electron microprobe traverse of samples before and after high-temperature exposure. Intermediate phases formed in the coating and diffusion zone were identified by X-ray diffraction in situ and after electrolytic extraction. The outer coating was found to consist of the inter-metallic compound, NiAl, while the diffusion zone contained MC, M23C6 or M6C carbides, and a phase in a matrix of NiAl + Nidl. Oxidation resulted in formation of an A1203 n'ch scale containing some Tz02. Depletion of aluminum during oxidation resulted in degradation of the outer coating to Ni3Al and the nickel alloy matrix. Diffusion of aluminum into the base metal was found to be slight and did not influence coating life significantly. The o formed in the diffusion zone during coating decomposed during elevated-temperature exposure to form stable carbide phases characteristic of the base metal. Diffusion zone phase changes were found to have no effect on the life of the aluminide coating in the oxidizing envzron?nent. THE oxidation resistance of many high-strength nickel-base superalloys is inadequate for extended exposure at temperatures above about 1600°F. In addition, some applications for these materials require that they be exposed to environments containing sulfur compounds and sodium salts which can cause surface attalk known as sulfidation or hot corrosion. In order to provide the necessary corrosion resistance to the high-strength alloys, protective coatings based on an aluminizing process have been developed. These processes, usually based on a pack cementation technique, result in the formation of a NiAl-rich outer coating layer either during the coating process or by a subsequent diffusion treatment. The performance of the aluminide coatings is affected by interactions between the coating layer and the base metal both during the coating process and during subsequent exposure at elevated temperatures. Knowledge of these interactions is required to guide the development of coatings capable of longer life and improved reliability. Goward et al.' recently reported the metallurgical factors which influence coating per- formance on MAR-M200. The present work is concerned with correlating the interactions and performance of coating compositions on several representative materials. EXPERIMENTAL PROCEDURES Materials. Three cast nickel-base superalloys which are used for turbine buckets in air-breathing engines were studied: IN 100, U-700, and SEL 15. Their chemical compositions are given in Table I. The alloys were vacuum-induction-melted and cast to slabs approximately 0.3 in. thick from which rectangular specimens 0.25 by 0.5 by 1 in. were machined. Coating Procedures. The machined specimens were coated by CODEP processes which were developed at the author's laboratory. These are based on pack cementation in various media to deposit either aluminum or aluminum in combination with titanium. The coating process which deposits only aluminum is designated CODEP-C, while the CODEP-D process deposits titanium in combination with aluminum. The CODEP-D process was applied only to IN 100. Both CODEP processes are applied at 1950" or 2000°F for 4 hr without need for a subsequent diffusion treatment. An outer coating about 1 mil in thickness is produced by these processes. Test Procedures. Coated specimens were exposed to static oxidation for periods ranging from 24 to 1000 hr at temperatures of 1600" to 2200°F. Terminal weight gain measurements and visual examination were used to evaluate oxidation resistance. including oxide spalling and coating failure. Both as-coated and exposed specimens of each alloy were studied by metallographic examination, electron microprobe analysis (EMA), and X-ray diffraction analysis either of the exposed surfaces or of phases extracted from the coating and diffusion zone. RESULTS As-Coated Condition. The microstructures of as-coated conditions were generally similar, irrespective of base materials or the particular coating process. They are typified by IN 100 coated by CODEP-D as shown in Fig. 1. The predominately single-phase outer layer, area A, Fig. 1, was identified by X-ray diffraction as the intermetallic compound NiA1. The NiAl zone extended inward to the original base metal interface. The diffusion zone, area B, Fig. 1, included carbide phases, a lamellar phase oriented perpendicular to the base metal surface, and a matrix phase consisting of a mixture of NiAl and Ni3Al. The phases in the diffusion zone were electrolytically extracted using a 10 pct HCl in methanol solution at approximately 1.3 amp per sq cm. The extracted phases were found to be M6C, MC, or M=C6 carbides and o as shown in Table I1 for each of the alloys. The d spacings from a typical diffraction pattern are

Jan 1, 1969

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By Samuel S. Wyer

Over 8,000,000 people in the United States depend on natural gas for their cooking, heating and lighting service. This service has been made possible only by the investment of large amounts of capital in transportation lines connecting the gas wells to the various communities, thus combining a hazardous mining operation with a public utility service. The effect that making these lines " common carriers" will have on the present and future service to these 8,000,000 or more people is of far reaching ethical and economic importance, and deserves careful consideration. As an introduction, it must be conceded that: 1. Natural gas, although a mineral and obtained by a mining operation—with more uncontrollable and uncertain features to cope with than exist in the mining of coal or other minerals—when served to the public becomes a public utility service. 2. The governmental power to regulate all public utilities in the interests of the public cannot be successfully disputed. 3. Mere suggestion of inconvenience to the utility is wholly irrelevant, as it cannot be considered or allowed to influence in making a defense against governmental regulation. Unfortunately it is not generally appreciated that:.. I . 1. Legislative enactments are not necessarily laws, and cannot abrogate economic laws or alter engineering facts. 2. There is a clear distinction between "common carrier7' and "public utility," although the terms are frequently confused. "A common carrier is one who undertakes for hire to transport persons or goods, or both, from place to place for all persons indifferently, the term implying indifference as to whom shall be served, and an equal readiness to serve all who apply, in the order of their application." On the other hand, property becomes a "public utility" only "when for a particular purpose the public have a right to resort to the premises and make use of them." It is, therefore, important to note that not all public utilities can be regarded as common carriers. The U. S. Supreme Court has already

Jan 1, 1915

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

By E. V. Foran

TheRe are many factors which control the ultimate production of oil and gas from a producing formation and the rate at which this production is obtained from any of the producing wells in the formation. The most important of these, and the one over which the greatest control can be exercised, is the differential pressure existing between the formation and the well bore. In producing any well by means of the gas-lift, it may be possible to change the flow tubing in a number of ways or vary the volume of circulating gas or air used for flowing the well, but if these operations, regardless of their magnitude, do not change the differential pressure between the producing sand and the well bore, they will in no way change the production of the well. If this statement is accepted as a fact, then all gas-lift or air-lift installations should be designed with but one object in view; namely, a means by which we can economically control very wide ranges of differential pressures between the formation and the well bore. Factors of Production In gas-lift production from any given formation, there are four major factors which govern the magnitude of the differential: (I) the depth of the well; (2) type and size of flow tubing; (3) volume of the circulating air or gas, and (4) physical properties of the oil-gas mixture after it has reached the well. The first of these factors is uncontrollable and does not vary. The other three are controllable within certain limits. The degree to which the last three factors can be controlled will cntircly govern the length of life of the well while on the lift, the lifting cost, and the daily production. It will also govern to some extent the ultimate production from the wells or leases producing by this method. These four factors will be discussed in detail in another part of this paper. Before proceeding further, a review of the present general practice in Texas, elsewhere than in the Gulf Coast region, will be given.

Jan 1, 1928

By Hannon, J. W. G.

Silicosis is today's most important industrial disease and probably dates back to the Stone Age. Since the industrial revolution, increasing attention has been paid to those occupations where mineral dust is present in the air breathed by the workers. For many years it was assumed that the inhalation of all mineral dusts was hazardous. but investigations conducted in several countries pointed the statistical finger of guilt at free silica in any of its numerous physical forms as a dust of outstanding toxicity. Recognition of silica as the chief hazard has resulted in widespread use of the term "silicosis." Depending upon the concentration of finely divided silica dust to which the individual is exposed and the duration of exposure, silicosis may become a disabling condition in from one to thirty years. The structure of the lung and respiratory passages is such that only minute particles of silica can gain entry to the air cells in the lung (5 microns or under are most toxic). When these minute particles gain entry to the lung tissues they stimulate certain protective cells in the lung to multiply at an excessive rate. The cell's undergo inflammatory changes which result in nodular scars and a low-grade inflammation of the lung tissue. These progressive changes in the lung structure gradually encroach

Jan 1, 1949

By Edward B. Hughes, Frank G. Norris

OXIDATION is characteristic of all processes for making steel from pig iron. This thought has been aptly expressed by H. W. Graham13 in the most recent Howe Memorial Lecture, "The process of steel-making consists of using iron oxide to reduce the carbon content of the pig iron to the desired level." Direct oxidation refers to the reaction that results from introducing oxygen either alone or mixed with other gases directly into the steel bath. In working a heat, oxygen in some form is added to the steel to remove the undesirable constituents as oxides. There are two general methods of supplying this oxygen to the open hearth bath. The method in which the oxygen is added as a, compound such as C02-or iron ore is designated an indirect method because the steel bath must first decompose the compound to attain oxygen in a usable form. The other method in which oxygen is added to the bath in the elemental or gaseous form, more or less diluted by other gases such as nitrogen, is a direct, method because no decomposition is necessary before the oxygen reacts with iron to form FeO which is dissolved in the bath in a usable form. Bubble formation (at least of a macroscopic size) presents no problem in case of direct oxidation because the reacting agent (oxygen) is in the form of bubbles when entering the metal. Regardless of whether oxygen is introduced into the bath directly or indirectly, several reactions proceed concurrently. In the presence of the bath of molten iron, FeO is formed either by oxidation of iron by oxygen or reduction of oxides by iron. This FeO dissolved in the molten iron is the source of oxygen for the oxidation of manganese, carbon, silicon, and phosphorus if these are present. The oxidation of carbon from steel is the controlling steelmaking reaction. The introduction of oxygen into the bath, its reaction in the elimination of impurities, and its control by the use of de-oxidizing additions have been subjects of importance since steel was first made by the bessemer process. Direct oxidation is, in a sense, an application of the bessemer principle to the open hearth process. Graham13 states: "The use of oxygen or air jets introduced into the metal bath is essentially an effort to approach in the open hearth the turbulence, rapid interface reaction, and high production rate per hour that exists in the bessemer process." The general subject, "Oxygen in Steelmaking," was given new life by the studies of Herty and associates starting about1925. The current interest in elemental oxygen is intimately related to the large scale production of oxygen developed during the war period. Some of the first applications were made during the early summer of 1946 at the Steel Co. of Canada using oxygen with the fuel. Such a use is of considerable interest and importance in contributing to faster heats but is not the subject of the present discussion which deals entirely with the introduction of elemental oxygen directly into the open hearth bath. A recent article12 reviewing the current

Jan 1, 1948

By Henry G. Granger

A RESIDENCE of 14 years in the Republic of Colombia, spent in almost continuous traveling and prospecting-trips, has given me an intimate knowledge of the resources of that wonderful country. The man who best knows Colombia is unquestionably General Rafael Reyes, President of the Republic for the past three years, and with seven years more to serve in his present term. Such is the strength of his personality and the wisdom of his policies that his term of office will no doubt endure as long as he is willing to serve. The vastly improved economic situation and the brilliant outlook for Colombia are so directly due to the influence of President Reyes that a few lines concerning him. will not be amiss, if they serve towards a better understanding of his personality. Born of a distinguished ancestry in the mountains of Boyaca, he is now 57 years old, just the age of his friend Porfirio Diaz when be began the work which has placed Mexico in the rank of great modern nations. It was Reyes who came to Washington to protest against the action of the government of the United States of America in reference to the establishment of the Republic of Panama, and, without entering into a discussion of this affair, it can be fairly said that there was not an American in Colombia whose feelings of justice were. not outraged at the government action and subsequent refusal to submit the matter to the impartial judgment of the' Hague. President Reyes is an accomplished linguist, speaking English, French, German, Portuguese, Spanish, and Italian. He has a remarkably. powerful voice, which can readily be heard by a large assemblage. His height is about 6 ft., and his weight exceeds 200 lb. He has clear gray eyes. Reyes was the leader of those who favored the approval of

Sep 1, 1908

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y' phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS' showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969

By C. E. Dobbin

THE identification of rock formations by a study of certain physical characteristics of burned samples was introduced in Wyoming in 1,926, when W. G. Buckles, superintendent. of the brick department of the Parco Development Co., reported to officials of the Producers & Refiners Corpn. that shales from the Cretaceous and older formations exposed between Parco and Rawlins exhibited distinctive coloration and textural features when burned in a standard brick kiln at temperatures ranging between 1000° and 3000° F. In collaboration with Elfred Beck, chief geologist of the Producers & Refiners Corpn., Buckles later burned cuttings and cores from several Wyoming wildcat wells in a standard kiln and successfully identified certain subsurface formations which had not been satisfactorily identified by other means. The results of their investigations were outlined in papers presented by Beck before the American Association of Petroleum Geologists at San Francisco in March, 1928, and by Buckles at. a joint meeting of the Rocky Mountain Oil and Gas Association and the Production Division of the American Petroleum Institute at Casper in November, 1928. These papers have not been published. The investigations set forth in this paper were carried out for. the purpose of determining the value of certain ceramic tests in assisting the petroleum engineers of the U. S. Geological Survey to identify well cuttings that represent Cretaceous shales penetrated beneath unconformable Tertiary formations in central, and eastern Wyoming, but that yield neither lithologic nor paleontologic criteria for satisfactory correlations with distinctive weathered outcrops. The investigations were made in the chemical laboratories of the Geological Survey at- Midwest, Wyo., and consisted of studying certain physical characteristics of burned bricks from representative outcrop samples of unweathered Cretaceous shales and of similarly burned cuttings of the same shales collected from wells in the Salt Creek oil field.

Jan 1, 1931

By A. L. Labbe

SOON after the Cottrell treater was placed in operation in the Murray plant in 1918 to treat combined lead sinter and Wedge roaster smoke, it was noticed that the power flowing through the treater did not remain constant. This was indicated by the varying milliamperes and also by the total amount of power consumed by the rectifiers. At times, for then unknown reasons, the treater current fluctuated through a wide range of from 40 to 300 milliamperes. Fortunately, these variations in power did not affect the treater's overall recovery, as this installation consisted of three independent units in series, a feature which made the Murray Cottrell an outstanding installation over many years of operation. Water conditioning of the smoke as a means of improving recovery was already known, but was not adaptable to this installation for reasons of excessive corrosion, which had been the case with other treaters using water as a conditioner exclusively. Tests conducted on the smoke had proved conclusively that water vapor played no part in the fluctuation of power, and the same was true of the SO2 contents and dust burden of the smoke. Neither did temperature variations of from 150 to 400°F have any effect on the power. Finally it was noticed that the variation in power taken by the treater, and the efficiency of recovery, had some definite relation to the number of Wedge roasters operating, and particularly to the sulphur contents of the charge. This observation soon led to the discovery that free sulphuric acid was the conditioner for Murray smoke and that variations in acid contents of smoke accounted for fluctuations of treater power. Analysis of recovered dust revealed that only a few hundredths of a per cent free acid was necessary to maintain a very efficient recovery. Once this knowledge was available, the roaster charge was adjusted as to sulphur contents to produce the necessary acid conditioner. For a number of years this practice was followed, but with improvements in the field of flotation, excess pyrites were eliminated from the smelting picture, so with a change in metallurgical practice we were confronted with the problem of providing the deficiency in acid by some other means. The situation was aggravated and our problem of acid conditioning made more difficult by the increase in the lead contents of concentrates roasted resulting from better flotation methods. The first step towards introducing acid vapors into the smoke stream by accessory means was accomplished by boiling sulphuric acid in cast iron pots placed in an open fire box. Acid fumes evaporated from the pots together with the combustion gases from the fire box were discharged into the flue through a cast iron pipe. Capacity of the iron pots was quite limited because of the comparatively slow rate of evaporation and the use of lump coal as a fuel, which did not lend itself to practical temperature control. This method of firing resulted in frequent pot failures due to overheating. In spite of these incidental difficulties, encountered in any new venture, the pot evaporator demonstrated the practicability of fuming sufficient acid to make up the deficiency in that naturally evolved in the Wedge furnace operation. As time progressed, less and less high sulphur material was available for Wedge roasting, and the necessity for accessory acid conditioning reached a climax when the supply of this material was entirely eliminated. Since the cast iron pots could only evaporate a few hundred pounds of acid per day, and were costly to replace, the logical thought presented itself of spraying the acid in a heated chamber. This new type of acid evaporator was simpler and more economical to operate and had sufficient capacity to fume several thousand pounds per day. The attached fig. 1 presents the outstanding features of the new furnace. A is the vaporizing drum, which is heated by the combustion gases of coal stoker fire box, B. Acid is sprayed into the hot gas stream within the drum through a number of air-acid atomizers, C, and the acid vapor, together with combustion gases, is introduced into the smoke stream through two cast iron pipes extending to different points in the flue. The operation of this type of furnace requires control of temperature inside the drum to prevent overheating, which dissociates the acid vapor to SO, and eventually to SO2, with resulting loss of acid. The dissociation to SO, at elevated temperatures is comparatively high, and in some cases accounts for as much as 60 pct of the acid sprayed into the drum. To reduce the loss of acid, through dissociation, some Cottrell plants, where the rate of acid sprayed reaches at times 9 ppm, use two evaporating units. Fuming the acid into the smoke stream is only

Jan 1, 1951

By Francis Pyne

THE following notes are presented in an endeavour to point out the disadvantages attending the use of chrome brick in reverberatory furnaces used in the treatment of materials that are too valuable to allow any great amount of metal absorption by the brick. Several years ago one of the large Eastern copper refineries decided to utilize basic material in place of siliceous material in the walls of their reverberatory furnaces for the treatment of very foul blister copper, as the latter rapidly corroded the siliceous linings. It was also expected that there would be less slag formation, with a consequent decrease in the cost of treatment and a reduction in the metal losses. Magnesite brick were first used, but while the corrosive action of the foul material was greatly reduced, and the amount of. slag formed was very much less, the magnesite proved to be unsatisfactory in certain parts of the furnace, because of its tendency to crack and span badly when subjected to the alternate heating and cooling that takes place in a reverberatory refining furnace. This made many repairs necessary, and consequent frequent interruption in the operation of the furnace, which, together with the high price of the magnesite brick, ran up the cost of maintenance to an unreasonable amount. It was, therefore, decided to substitute chronic brick for magnesite brick in the parts of the furnace affected. The results, as far as the reverberatory furnace was concerned, were very satisfactory. The corrosion due to the action of the foul blister was small and the amount of slag formed was no greater than when using magnesite, and the tendency to crack and spill shown by the magnesite was eliminated. Gradually the use of chrome brick was extended to all furnaces; those treating blister copper as well as those melting cathodes, and the results were so satin-, factory that the siliceous roofs were replaced by roofs of chrome brick except in certain places where experience showed a more satisfactory performance on the part of the silica brick.

Jan 12, 1917

By J. P. Sheehan, W. R. Hibbard, M. Baeyertz

This paper deals with molybdenum modifications of 5140 steel that have the same hardenability but a better tolerance for phosphorus than the AISI-SAE 5140 grade. Lack of toughness in steels with higher than normal phosphorus contents is well known to metallurgists. This problem is troublesome even within normal phosphorus ranges, if the heat treatment or the design of the part or the service is critical. Under such unfavorable conditions and also in the case of phosphorus contents toward the upper side of the commercial range, the use of molybdenum to replace a part of the chromium in 5140 steel provides a factor of safety. The toughness of steel is variously exhibited in different mechanical tests; broadly the term is applied to the capacity of the steel to deform prior to fracture. Defined in this way, toughness is considered to be an inherent quality that depends upon the composition and structure of the steel, and also upon its temperature during deformation and fracture in the test. In the present state of our knowledge, the type of mechanical test needs to be included in any discussion of toughness, because the revelation of this quality in steel depends on the stress state and rate of stressing imposed by the test. In comparing the toughness of one steel with another by laboratory testing, it has long been customary to use notched tests that impose severe constmint to deformation, and then to test over a range of temperatures to obtain the so-called transition. At temperatures above the transition, the steel fails after considerable deformation and absorption of energy. Below the transition, less energy is absorbed as the steel fails largely by cleavage. The transition range itself is characterized by a more or less abrupt change in energy absorption and type of fracture. The conventional V-notch Charpy impact test has been used exclusively in the work covered by this report. For the steels under study, rather sharp transitions are obtained with this test, at testing temperatures that are easily obtained in the laboratory. The position of the transition on the testing temperature scale provides a rather sensitive index of the toughness of the steel, when the steels under study are similar in character as they are in this work. Turning to the metallurgical reasons for the greater toughness of one steel as compared to another, the authors propose to limit the discussion to the small field under study. Only one structural state is considered, tempered martensite of a hardness of about 28 Rockwell C or 269 Brinell. The study deals first with the loss of toughness in AISI-SAE 5140 steel caused by increasing the phosphorus content from about 0.020 to 0.040 pct. A second part of the work deals with counteracting this loss in toughness by replacing a part of the chromium by molybdenum. A series of molybdenum modifications was studied, in each of which the chromium was reduced sufficiently to duplicate the hardenability of 5140 steel. Phosphorus affects the toughness of steel in two ways. An inherent lack of toughness of phosphorus-bearing ferrite as compared to low phosphorus ferrite has often been noted. Jolivet and Vidall have shown that phosphorus has the same effect in tempered martensite in chromium steels. The other well known effect of phosphorus is to make steel susceptible to temper embrittlement. Temper brittleness is a loss in toughness brought about by tempering steel within a limited temperature interval somewhat below the A1 temperature. In most of the standard AISI-SAE alloy steels, this temperature interval is approximately 850-1100°F. Either of these types of loss in toughness is easily followed by the shift in the transition temperature obtained with the notched-bar impact test. The data to be presented show the beneficial effect of substituting molybdenum for a part of the chromium in 5140 steel with either moderate (0.020 pct) or high (0.040 pct) phosphorus contents. Both the inherent lack of toughness of phosphorus-bearing steel and temper brittleness are counteracted by this use of molybdenum. The work of Jolivet and Vidal mentioned above shows the detrimental effect of phosphorus on the toughness of tempered martensite in the absence of temper embrittlement, as well as the temper brittleness caused by phosphorus. They used two steels, essentially 0.25 pct C-1.4 pct Cr, with 0.044 and 0.013 pct P, respectively. The nonembrittled state was obtained by quenching in oil from 1610°F, then tempering for one hour at 1200°F and quenching in water. In this state the transition temperature range of the low phosphorus steel in the notched-bar impact test was below that of the steel with 0.044 pct P. An additional treatment of 24 hr at 975°F (that is, in the embrittling range) caused both steels to lose toughness, but the high phosphorus steel showed the greater embrittlement. Recently Hollomon2 has published a comprehensive survey and bibliography of the literature on temper brittleness, to which the reader is re-

Jan 1, 1950

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By C. E. Shoenfelt, E. W. Krampert

The major oil discovery in 1938 for Wyoming was the General Petroleum Corporation's So. 1 Government, C.NW.SE. of sec. 21-35N-77W, on the Cole Creek structure in central Wyoming, 14 miles northeast of Casper. This well found commercial oil production in basal Cloverly sand (Lakota) at 7978 ft. and was completed on May 28, 1938, at 8019 ft., 3 ft. in Morrison shale. It had an initial produrtion of 10 bbl. of oil an hour but at the end of a 7-day test made 336 bbl. of oil in 24 hr. During 1938, the well produced a total of 23,161 bbl. of oil. It has been agitated about 10 days out of each month to provide fuel for lease and drilling operations, the balance of the time it has been shut in pending the completion of the second well on the structure. The Cole Creek oil is of intermediate base and has an A.P.I. gravity of 32.7". The record of the well contains the "tops" listed in the accompanying tabulation. Tops in General Petroleum Corporation's No. 1 Government Well Feet 2210 Top of the Mesa Verde (Teapot sandstone) 2960 Top Steele shale 4500 Shannon sand; good show of oil and gas 6740 Top Frontier sand; some oil saturation 6840 Halliburton test of Froutier did not show much oil, but at 6878 ft. the oil showing amounted to 50 barrels 6878-7051 Shale 7051-7062 Sand with some oil saturation 7062-7920 Shale (sandy phase of Thermopolis shale 7779 to 7788 ft.) 7920-7926 Sand (Muddy); oil-saturated 7926-7974 Shale 7974-7979 Hard, coarse, limy sand (Dakota); some oil saturation 7979-7997 Soft sand; high oil saturation 7997-8002 Shale with pyrites 8002-8016 Sand (Lakota) 8016-8019 Variegated Morrison shale 5600 Elevation Lance Creek Field.—Important extensions to the Lance Creek field in eastern Wyoming were made in 1938 by the completion of a number of

Jan 1, 1939

By Clinton M. Young

(Pittsburg Meeting, March, 1910.) I. INTRODUCTION. THE experiments herein. described were carried on in 1908-9 . by the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coal-mines, a subject which is engaging the attention. of numerous investigators. An unusual number of serious disasters has directed to. the subject a study which discloses the disquieting fact that, in the. United States, the ratio of lives lost per ton of coal mined has been on the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in, comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and. a very great increase in the amount of explosive used.. . This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle. West it is not now uncommon for a miner to use six ,kegs (150 lb.) of black powder in a "pay" of two weeks, while within the memory. of men still active, one keg (25 .lb.) would last two men for a " pay." So. great has . the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject. of explosions in coal-mines has. led to the belief . that the use of, large -quantities of explosives, in some cases by slightly-trained men, had not been * Associate Professor- of Mining Engineering, University of Kansas, Lawrence, Ran.

Aug 1, 1910

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947